Download or read book RF Sputtered Back Contacts for CdS CdTe Thin Film Solar Cells written by Vijay Viswanathan and published by . This book was released on 1997 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book RF Magnetron Triode Sputtering of CdTe and ZnTe Films and Solar Cells written by Adam Lee Sanford and published by . This book was released on 2002 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: The n-CdS/p-CdTe solar cell has been researched for many years now. Research groups use a variety of processes to fabricate thin-film CdS/CdTe cells, including physical vapor deposition, chemical vapor deposition, and RIF diode sputtering. One of the central areas of investigation concerning CdS/CdTe cells is the problem of a Schottky barrier at the back contact. Even cells fabricated with ohmic back contacts degrade into Schottky barriers as the devices are used. This severely degrades power generation. One possible solution is to use p-ZnTe as an interlayer between CdTe and the back contact. ZnTe is easily doped with Cu to be p-type. However, even contacts with this ZnTe interlayer degrade over time, because Cu is highly mobile and diffuses away from the contact towards the CdS/CdTe junction. Another possibility is to dope ZnTe with N. It has been demonstrated using molecular beam epitaxy and RF diode sputtering. In this study, CdTe films are fabricated using a variation of RF diode sputtering called triode sputtering. This technique allows for control of ion bombardment to the substrate during deposition. Also, a higher plasma density near the target is achieved allowing depositions at lower pressures. These films are characterized structurally to show the effects of the various deposition parameters. N-doped ZnTe films are also fabricated using this technique. These films are characterized electrically to show the effects of the various deposition parameters. Also, the effects of post-deposition annealing are observed. It is found that annealing at the right temperature can increase the conductivity of the films by a factor of 3 or more. However, annealing at higher temperatures decreases the conductivity to as low as 12% of the initial conductivity. Finally, RF triode sputtered N-doped ZnTe films are used as an interlayer at the back contact of a CdS/CdTe solar cell. The effects of annealing the device before and after contact deposition are observed. Annealing before depositing contacts results in an increase in V[Subscript oc] of 20mV. Annealing after contact deposition results in a degradation of fill factor over time.
Download or read book Chalcogenide Photovoltaics written by Roland Scheer and published by John Wiley & Sons. This book was released on 2011-03-31 with total page 398 pages. Available in PDF, EPUB and Kindle. Book excerpt: This first comprehensive description of the most important material properties and device aspects closes the gap between general books on solar cells and journal articles on chalcogenide-based photovoltaics. Written by two very renowned authors with years of practical experience in the field, the book covers II-VI and I-III-VI2 materials as well as energy conversion at heterojunctions. It also discusses the latest semiconductor heterojunction models and presents modern analysis concepts. Thin film technology is explained with an emphasis on current and future techniques for mass production, and the book closes with a compendium of failure analysis in photovoltaic thin film modules. With its overview of the semiconductor physics and technology needed, this practical book is ideal for students, researchers, and manufacturers, as well as for the growing number of engineers and researchers working in companies and institutes on chalcogenide photovoltaics.
Download or read book Recent Advances in Thin Film Photovoltaics written by Udai P. Singh and published by Springer Nature. This book was released on 2022-09-02 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides recent development in thin-film solar cells (TFSC). TFSC have proven the promising approach for terrestrial and space photovoltaics. TFSC have the potential to change the device design and produce high efficiency devices on rigid/flexible substrates with significantly low manufacturing cost. TFSC have several advantages in manufacturing compared to traditional crystalline Si-solar cells like less requirement of materials, can be prepared with earth’s abundant materials, less processing steps, easy to dispose, etc. Several universities/research institutes/industry in India and abroad are involved in the research area of thin-film solar cells. The book helps the readers to find the details about different thin-film technologies and its advancement at one place. Each chapter covers properties of materials, its suitability for PV applications, simple manufacturing processes and recent and past literature survey. The issues related to the development of high efficiency TFSC devices over large area and its commercial and future prospects are discussed.
Download or read book McEvoy s Handbook of Photovoltaics written by Soteris Kalogirou and published by Academic Press. This book was released on 2017-08-24 with total page 1341 pages. Available in PDF, EPUB and Kindle. Book excerpt: Practical Handbook of Photovoltaics, Third Edition, is a 'benchmark' publication for those involved in the design, manufacture and use of these devices. This fully revised handbook includes brand new sections on smart grids, net metering and the modeling of photovoltaic systems, as well as fully revised content on developments in photovoltaic applications, the economics of PV manufacturing and updated chapters on solar cell function, raw materials, photovoltaic standards, calibration and testing, all with new examples and case studies. The editor has assembled internationally-respected contributors from industry and academia around the world to make this a truly global reference. It is essential reading for electrical engineers, designers of systems, installers, architects, policymakers and physicists working with photovoltaics. - Presents a cast of international experts from industry and academia to ensure the highest quality information from multiple stakeholder perspectives - Covers all things photovoltaics, from the principles of solar cell function and their raw materials, to the installation and design of full photovoltaic systems - Includes case studies, practical examples, and reports on the latest advances and worldwide applications
Download or read book Development of Back Contacts for CdTe Thin Films Solar Cells written by Fadhil Khalaf Dahash Alfadhili and published by . This book was released on 2020 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thin film solar cells based on polycrystalline p-type cadmium telluride (CdTe) represent one of these the most promising photovoltaic (PV) device due to high efficiency and low-cost production. Currently, CdTe solar cells provide the lowest cost electricity generation in utility-scale applications, which is a cost-competitive with the traditional power source, fossil fuel. CdTe thin film PV has attained 22.1 % of power conversion efficiency for small area scale and 18.6 % for modules scale. However, the high efficiency of CdTe devices has been achieved by increasing the photo-generated current by changing the traditional window layer (CdS) of CdTe to a wider bandgap material with better band alignment. The open-circuit voltage (VOC) remains below the theoretical limit due to a barrier at the back of the device due to the deep valence band edge of CdTe (-5.9 eV). Voc can be increased by adding a buffer layer between CdTe and the back electrode to decrease band banding and reducing carrier recombination at the back interface. In this thesis, several materials were investigated as a back-buffer layer, such as single-wall carbon nanotube (SWCNT), zinc telluride (ZnTe), tellurium (Te), and cadmium zinc telluride (CZT) to minimize the bend bending at CdTe/back-buffer layer interface. An alternative method to reduce the carrier recombination at the rear surface, the use of aluminum oxide (Al2O3) layer as a passivation layer was also demonstrated. Finally, an effective method of CdCl2 treatment for CZT thin film was investigated. This method shows that zinc (Zn) can be maintained during the heat treatment.
Download or read book Semiconductor Photovoltaic Cells written by Chunfu Zhang and published by Springer Nature. This book was released on 2021-02-25 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores the scientific basis of the photovoltaic effect, solar cell operation, various types of solar cells, and the main process used in their manufacture. It addresses a range of topics, including the production of solar silicon; silicon-based solar cells and modules; the choice of semiconductor materials and their production-relevant costs and performance; device structures, processing, and manufacturing options for the three major thin-film PV technologies; high-performance approaches for multi-junction, concentrator, and space applications; and new types of organic polymer and dye-sensitized solar cells. The book also presents a concept for overcoming the efficiency limit of today’s solar cells. Accessible for beginners, while also providing detailed information on the physics and technology for experts, the book is a valuable resource for researchers, engineers, and graduate students in fields such as physics, materials, energy, electrical and electronic engineering and microelectronics.
Download or read book Clean Electricity From Photovoltaics written by Mary D Archer and published by World Scientific. This book was released on 2001-06-04 with total page 870 pages. Available in PDF, EPUB and Kindle. Book excerpt: Photovoltaic cells provide clean, reversible electrical power from the sun. Made from semiconductors, they are durable, silent in operation and free of polluting emissions. In this book, experts from all sectors of the PV community — materials scientists, physicists, production engineers, economists and environmentalists — give their critical appraisals of where the technology is now and what its prospects are./a
Download or read book Solar Cells and Modules written by Arvind Shah and published by Springer Nature. This book was released on 2020-07-16 with total page 357 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives a comprehensive introduction to the field of photovoltaic (PV) solar cells and modules. In thirteen chapters, it addresses a wide range of topics including the spectrum of light received by PV devices, the basic functioning of a solar cell, and the physical factors limiting the efficiency of solar cells. It places particular emphasis on crystalline silicon solar cells and modules, which constitute today more than 90 % of all modules sold worldwide. Describing in great detail both the manufacturing process and resulting module performance, the book also touches on the newest developments in this sector, such as Tunnel Oxide Passivated Contact (TOPCON) and heterojunction modules, while dedicating a major chapter to general questions of module design and fabrication. Overall, it presents the essential theoretical and practical concepts of PV solar cells and modules in an easy-to-understand manner and discusses current challenges facing the global research and development community.
Download or read book II IV Compound Semiconductor Photovoltaic Materials Volume 668 written by Robert Birkmire and published by . This book was released on 2001-10-15 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on materials issues related to Cu(In,Ga)(Se,S)2 and CdTe-based polycrystalline thin-film photovoltaic solar cells and related oxides and chalcogenides. Phase equilibrium and thermochemical kinetic aspects of the absorber layer formation of CdTe and Cu(In,Ga)(Se,S)2 are emphasized and several papers on micro-analytical analysis report on detailed structural properties of thin films. The use of flexible plastic or metal foil substrates as an alternative to glass is addressed in terms of solar-cell performance and limitations imposed by the nature of the substrates. Properties of defects and interfaces in CdTe and CIGSS are highlighted using electrical, optical, and micro-analytical tools. While film properties are correlated to device physics, controversy still exists on the detailed operation of both CdTe and CIGSS devices. Topics include: materials and synthesis; thin films on alternate substrates; defects; growth and junction formation; surfaces and interfaces and film and device characterization.
Download or read book CdTe and Related Compounds Physics Defects Hetero and Nano structures Crystal Growth Surfaces and Applications written by and published by Elsevier. This book was released on 2009-11-11 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Almost thirty years after the remarkable monograph of K. Zanio and the numerous conferences and articles dedicated since that time to CdTe and CdZnTe, after all the significant progresses in that field and the increasing interest in these materials for several extremely attractive industrial applications, such as nuclear detectors and solar cells, the edition of a new enriched and updated monograph dedicated to these two very topical II-VI semiconductor compounds, covering all their most prominent, modern and fundamental aspects, seemed very relevant and useful. - Detailed coverage of the main topics associated with the very topical II-VI semiconductor compound CdTe and its alloy CZT - Review of the CdTe recent developments - Fundamental background of many topics clearly introduced and exposed
Download or read book Capacitance Characteristics of RF Sputtered CdS CdTe Solar Cells written by Faming Shen and published by . This book was released on 1995 with total page 94 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advances in Composite Materials for Medicine and Nanotechnology written by Brahim Attaf and published by BoD – Books on Demand. This book was released on 2011-04-01 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to their good mechanical characteristics in terms of stiffness and strength coupled with mass-saving advantage and other attractive physico-chemical properties, composite materials are successfully used in medicine and nanotechnology fields. To this end, the chapters composing the book have been divided into the following sections: medicine, dental and pharmaceutical applications; nanocomposites for energy efficiency; characterization and fabrication, all of which provide an invaluable overview of this fascinating subject area. The book presents, in addition, some studies carried out in orthopedic and stomatological applications and others aiming to design and produce new devices using the latest advances in nanotechnology. This wide variety of theoretical, numerical and experimental results can help specialists involved in these disciplines to enhance competitiveness and innovation.
Download or read book Inorganic Flexible Optoelectronics written by Zhenqiang Ma and published by John Wiley & Sons. This book was released on 2019-04-29 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensively covering inorganic flexible optoelectronics and their applications This highly application-oriented book provides an overview of the vibrant research field of inorganic flexible optoelectronics ? from materials to applications ? covering bulk materials as well as nanowires, thin films, nanomembranes for application in light emitting diodes, photodetectors, phototransistors, and solar cells. Edited and written by world-leading experts in the field, Inorganic Flexible Optoelectronics: Materials and Applications begins by covering flexible inorganic light emitting diodes enabled by new materials and designs, and provides examples of their use in neuroscience research. It then looks at flexible light-emitting diodes based on inorganic semiconductor nanostructures ? from thin films to nanowires. Next, the book examines flexible photodetectors with nanomembranes and nanowires; 2-D material based photodetectors on flexible substrates; and IV group materials based solar cells and their flexible photovoltaic technologies. Following that, it presents readers with a section on thin-film III-V single junction and multijunction solar cells and demonstrates their integration onto heterogeneous substrates. Finally, the book finishes with in-depth coverage of novel materials based flexible solar cells. -A must-have book that provides an unprecedented overview of the state of the art in flexible optoelectronics -Supplies in-depth information for new and already active researchers in the field of optoelectronics -Lays down the undiluted knowledge on inorganic flexible optoelectronics ? from materials to devices -Focuses on materials and devices for high-performance applications such as light-emitting diodes, solar cells, and photodetectors Inorganic Flexible Optoelectronics: Materials and Applications appeals to materials scientists, electronics engineers, electrical engineers, inorganic chemists, and solid state physicists.
Download or read book Study of Back Contact Formation on CdTe CdS Thin Film Solar Cells written by Jian Tang and published by . This book was released on 1998 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Tellurium Chemistry written by Bimal Krishna Banik and published by Walter de Gruyter GmbH & Co KG. This book was released on 2022-10-03 with total page 508 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tellurium, a well-known chalcogen, finds potential applications in various fields from chemistry to other branches of science such as nanotechnology and macromolecular science. However, its safety must also be taken into consideration when exploring its industrial applications. This book explores the breadth of tellurium‘s applications, outlines strategies for industrial use, and describes the safety concerns of this element.
Download or read book Study Of Cu Free Back Contacts to Thin Film CdTe Solar Cells written by Vijay Viswanathan and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: ABSTRACT: The effect of etching ambient, pressure, plasma power and etch time on contact performance will be studied.
