Download or read book Fault Diagnosis Systems written by Rolf Isermann and published by Springer Science & Business Media. This book was released on 2006-01-16 with total page 478 pages. Available in PDF, EPUB and Kindle. Book excerpt: With increasing demands for efficiency and product quality plus progress in the integration of automatic control systems in high-cost mechatronic and safety-critical processes, the field of supervision (or monitoring), fault detection and fault diagnosis plays an important role. The book gives an introduction into advanced methods of fault detection and diagnosis (FDD). After definitions of important terms, it considers the reliability, availability, safety and systems integrity of technical processes. Then fault-detection methods for single signals without models such as limit and trend checking and with harmonic and stochastic models, such as Fourier analysis, correlation and wavelets are treated. This is followed by fault detection with process models using the relationships between signals such as parameter estimation, parity equations, observers and principal component analysis. The treated fault-diagnosis methods include classification methods from Bayes classification to neural networks with decision trees and inference methods from approximate reasoning with fuzzy logic to hybrid fuzzy-neuro systems. Several practical examples for fault detection and diagnosis of DC motor drives, a centrifugal pump, automotive suspension and tire demonstrate applications.
Download or read book Fault Tolerant Process Control written by Prashant Mhaskar and published by Springer Science & Business Media. This book was released on 2012-11-27 with total page 279 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fault-Tolerant Process Control focuses on the development of general, yet practical, methods for the design of advanced fault-tolerant control systems; these ensure an efficient fault detection and a timely response to enhance fault recovery, prevent faults from propagating or developing into total failures, and reduce the risk of safety hazards. To this end, methods are presented for the design of advanced fault-tolerant control systems for chemical processes which explicitly deal with actuator/controller failures and sensor faults and data losses. Specifically, the book puts forward: · A framework for detection, isolation and diagnosis of actuator and sensor faults for nonlinear systems; · Controller reconfiguration and safe-parking-based fault-handling methodologies; · Integrated-data- and model-based fault-detection and isolation and fault-tolerant control methods; · Methods for handling sensor faults and data losses; and · Methods for monitoring the performance of low-level PID loops. The methodologies proposed employ nonlinear systems analysis, Lyapunov techniques, optimization, statistical methods and hybrid systems theory and are predicated upon the idea of integrating fault-detection, local feedback control, and supervisory control. The applicability and performance of the methods are demonstrated through a number of chemical process examples. Fault-Tolerant Process Control is a valuable resource for academic researchers, industrial practitioners as well as graduate students pursuing research in this area.
Download or read book Process Control System Fault Diagnosis written by Ruben Gonzalez and published by John Wiley & Sons. This book was released on 2016-07-25 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Control System Fault Diagnosis: A Bayesian Approach Ruben T. Gonzalez, University of Alberta, Canada Fei Qi, Suncor Energy Inc., Canada Biao Huang, University of Alberta, Canada Data-driven Inferential Solutions for Control System Fault Diagnosis A typical modern process system consists of hundreds or even thousands of control loops, which are overwhelming for plant personnel to monitor. The main objectives of this book are to establish a new framework for control system fault diagnosis, to synthesize observations of different monitors with a prior knowledge, and to pinpoint possible abnormal sources on the basis of Bayesian theory. Process Control System Fault Diagnosis: A Bayesian Approach consolidates results developed by the authors, along with the fundamentals, and presents them in a systematic way. The book provides a comprehensive coverage of various Bayesian methods for control system fault diagnosis, along with a detailed tutorial. The book is useful for graduate students and researchers as a monograph and as a reference for state-of-the-art techniques in control system performance monitoring and fault diagnosis. Since several self-contained practical examples are included in the book, it also provides a place for practicing engineers to look for solutions to their daily monitoring and diagnosis problems. Key features: • A comprehensive coverage of Bayesian Inference for control system fault diagnosis. • Theory and applications are self-contained. • Provides detailed algorithms and sample Matlab codes. • Theory is illustrated through benchmark simulation examples, pilot-scale experiments and industrial application. Process Control System Fault Diagnosis: A Bayesian Approach is a comprehensive guide for graduate students, practicing engineers, and researchers who are interests in applying theory to practice.
Download or read book Fault Detection and Diagnosis in Industrial Systems written by L.H. Chiang and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 281 pages. Available in PDF, EPUB and Kindle. Book excerpt: Early and accurate fault detection and diagnosis for modern chemical plants can minimize downtime, increase the safety of plant operations, and reduce manufacturing costs. This book presents the theoretical background and practical techniques for data-driven process monitoring. It demonstrates the application of all the data-driven process monitoring techniques to the Tennessee Eastman plant simulator, and looks at the strengths and weaknesses of each approach in detail. A plant simulator and problems allow readers to apply process monitoring techniques.
Download or read book Fault Diagnosis and Reconfiguration in Flight Control Systems written by C. Hajiyev and published by Springer Science & Business Media. This book was released on 2013-12-01 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: The problem of fault diagnosis and reconfigurable control is a new and actually developing field of science and engineering. The subject becomes more interesting since there is an increasing demand for the navigation and control systems of aerospace vehicles, automated actuators etc. to be more safe and reliable. Nowadays, the problems of fault detection and isolation and reconfigurable control attract the attention the scientists in the world. The subject is emphasized in the recent international congresses such as IF AC World Congresses (San Francisco-1996, Beijing-1999, and Barcelona-2002) and lMEKO World Congresses (Tampere-1997, Osaka-1999, Vienna-2000), and also in the international conferences on fault diagnosis such as SAFEPROCESS Conferences (Hull-1997, Budapest-2000). The presented methods in the book are based on linear and nonlinear dynamic mathematical models of the systems. Technical objects and systems stated by these models are very large, and include various control systems, actuators, sensors, computer systems, communication systems, and mechanical, hydraulic, pneumatic, electrical and electronic devices. The analytical fault diagnosis techniques of these objects have been developed for several decades. Many of those techniques are based on the use of the results of modem control theory. This is natural, because it is known that fault diagnosis process in control systems is considered as a part of general control process. xxii In organization of fault diagnosis of control systems, the use of the concepts and methods of modem control theory including concepts of state space, modeling, controllability, observability, estimation, identification, and filtering is very efficient.
Download or read book Issues of Fault Diagnosis for Dynamic Systems written by Ron J. Patton and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the time our first book Fault Diagnosis in Dynamic Systems: The ory and Applications was published in 1989 by Prentice Hall, there has been a surge in interest in research and applications into reliable methods for diag nosing faults in complex systems. The first book sold more than 1,200 copies and has become the main text in fault diagnosis for dynamic systems. This book will follow on this excellent record by focusing on some of the advances in this subject, by introducing new concepts in research and new application topics. The work cannot provide an exhaustive discussion of all the recent research in fault diagnosis for dynamic systems, but nevertheless serves to sample some of the major issues. It has been valuable once again to have the co-operation of experts throughout the world working in industry, gov emment establishments and academic institutions in writing the individual chapters. Sometimes dynamical systems have associated numerical models available in state space or in frequency domain format. When model infor mation is available, the quantitative model-based approach to fault diagnosis can be taken, using the mathematical model to generate analytically redun dant alternatives to the measured signals. When this approach is used, it becomes important to try to understand the limitations of the mathematical models i. e. , the extent to which model parameter variations occur and the effect of changing the systems point of operation.
Download or read book Fault Diagnosis and Reconfiguration in Flight Control Systems written by Chingiz Hajiyev and published by . This book was released on 2014-09-01 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Data driven Design of Fault Diagnosis and Fault tolerant Control Systems written by Steven X. Ding and published by Springer Science & Business Media. This book was released on 2014-04-12 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: Data-driven Design of Fault Diagnosis and Fault-tolerant Control Systems presents basic statistical process monitoring, fault diagnosis, and control methods and introduces advanced data-driven schemes for the design of fault diagnosis and fault-tolerant control systems catering to the needs of dynamic industrial processes. With ever increasing demands for reliability, availability and safety in technical processes and assets, process monitoring and fault-tolerance have become important issues surrounding the design of automatic control systems. This text shows the reader how, thanks to the rapid development of information technology, key techniques of data-driven and statistical process monitoring and control can now become widely used in industrial practice to address these issues. To allow for self-contained study and facilitate implementation in real applications, important mathematical and control theoretical knowledge and tools are included in this book. Major schemes are presented in algorithm form and demonstrated on industrial case systems. Data-driven Design of Fault Diagnosis and Fault-tolerant Control Systems will be of interest to process and control engineers, engineering students and researchers with a control engineering background.
Download or read book Diagnosis and Fault tolerant Control Volume 2 written by Vicenc Puig and published by John Wiley & Sons. This book was released on 2021-12-29 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents recent advances in fault diagnosis and fault-tolerant control of dynamic processes. Its impetus derives from the need for an overview of the challenges of the fault diagnosis technique and sustainable control, especially for those demanding systems that require reliability, availability, maintainability, and safety to ensure efficient operations. Moreover, the need for a high degree of tolerance with respect to possible faults represents a further key point, primarily for complex systems, as modeling and control are inherently challenging, and maintenance is both expensive and safety-critical. Diagnosis and Fault-tolerant Control 2 also presents and compares different fault diagnosis and fault-tolerant schemes, using well established, innovative strategies for modeling the behavior of the dynamic process under investigation. An updated treatise of diagnosis and fault-tolerant control is addressed with the use of essential and advanced methods including signal-based, model-based and data-driven techniques. Another key feature is the application of these methods for dealing with robustness and reliability.
Download or read book Process Control System Fault Diagnosis written by Ruben Gonzalez and published by John Wiley & Sons. This book was released on 2016-07-21 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: Process Control System Fault Diagnosis: A Bayesian Approach Ruben T. Gonzalez, University of Alberta, Canada Fei Qi, Suncor Energy Inc., Canada Biao Huang, University of Alberta, Canada Data-driven Inferential Solutions for Control System Fault Diagnosis A typical modern process system consists of hundreds or even thousands of control loops, which are overwhelming for plant personnel to monitor. The main objectives of this book are to establish a new framework for control system fault diagnosis, to synthesize observations of different monitors with a prior knowledge, and to pinpoint possible abnormal sources on the basis of Bayesian theory. Process Control System Fault Diagnosis: A Bayesian Approach consolidates results developed by the authors, along with the fundamentals, and presents them in a systematic way. The book provides a comprehensive coverage of various Bayesian methods for control system fault diagnosis, along with a detailed tutorial. The book is useful for graduate students and researchers as a monograph and as a reference for state-of-the-art techniques in control system performance monitoring and fault diagnosis. Since several self-contained practical examples are included in the book, it also provides a place for practicing engineers to look for solutions to their daily monitoring and diagnosis problems. Key features: • A comprehensive coverage of Bayesian Inference for control system fault diagnosis. • Theory and applications are self-contained. • Provides detailed algorithms and sample Matlab codes. • Theory is illustrated through benchmark simulation examples, pilot-scale experiments and industrial application. Process Control System Fault Diagnosis: A Bayesian Approach is a comprehensive guide for graduate students, practicing engineers, and researchers who are interests in applying theory to practice.
Download or read book Model Based Fault Diagnosis Techniques written by Steven X. Ding and published by Springer Science & Business Media. This book was released on 2012-12-20 with total page 533 pages. Available in PDF, EPUB and Kindle. Book excerpt: Guaranteeing a high system performance over a wide operating range is an important issue surrounding the design of automatic control systems with successively increasing complexity. As a key technology in the search for a solution, advanced fault detection and identification (FDI) is receiving considerable attention. This book introduces basic model-based FDI schemes, advanced analysis and design algorithms, and mathematical and control-theoretic tools. This second edition of Model-Based Fault Diagnosis Techniques contains: • new material on fault isolation and identification and alarm management; • extended and revised treatment of systematic threshold determination for systems with both deterministic unknown inputs and stochastic noises; • addition of the continuously-stirred tank heater as a representative process-industrial benchmark; and • enhanced discussion of residual evaluation which now deals with stochastic processes. Model-based Fault Diagnosis Techniques will interest academic researchers working in fault identification and diagnosis and as a text it is suitable for graduate students in a formal university-based course or as a self-study aid for practising engineers working with automatic control or mechatronic systems from backgrounds as diverse as chemical process and power engineering.
Download or read book Advanced methods for fault diagnosis and fault tolerant control written by Steven X. Ding and published by Springer Nature. This book was released on 2020-11-24 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt: The major objective of this book is to introduce advanced design and (online) optimization methods for fault diagnosis and fault-tolerant control from different aspects. Under the aspect of system types, fault diagnosis and fault-tolerant issues are dealt with for linear time-invariant and time-varying systems as well as for nonlinear and distributed (including networked) systems. From the methodological point of view, both model-based and data-driven schemes are investigated.To allow for a self-contained study and enable an easy implementation in real applications, the necessary knowledge as well as tools in mathematics and control theory are included in this book. The main results with the fault diagnosis and fault-tolerant schemes are presented in form of algorithms and demonstrated by means of benchmark case studies. The intended audience of this book are process and control engineers, engineering students and researchers with control engineering background.
Download or read book Diagnosis and Fault Tolerant Control written by Mogens Blanke and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 583 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents model-based analysis and design methods for fault diagnosis and fault-tolerant control. Architectural and structural models are used to analyse the propagation of the fault through the process, test fault detectability and reveal redundancies that can be used to ensure fault tolerance. Case studies demonstrate the methods presented. The second edition includes new material on reconfigurable control, diagnosis of nonlinear systems, and remote diagnosis, plus new examples and updated bibliography.
Download or read book Fault Diagnosis of Nonlinear Systems Using a Hybrid Approach written by Ehsan Sobhani-Tehrani and published by Springer Science & Business Media. This book was released on 2009-06-22 with total page 275 pages. Available in PDF, EPUB and Kindle. Book excerpt: Theincreasingcomplexityofspacevehiclessuchassatellites,andthecostreduction measures that have affected satellite operators are increasingly driving the need for more autonomy in satellite diagnostics and control systems. Current methods for detecting and correcting anomalies onboard the spacecraft as well as on the ground are primarily manual and labor intensive, and therefore, tend to be slow. Operators inspect telemetry data to determine the current satellite health. They use various statisticaltechniques andmodels,buttheanalysisandevaluation ofthelargevolume of data still require extensive human intervention and expertise that is prone to error. Furthermore, for spacecraft and most of these satellites, there can be potentially unduly long delays in round-trip communications between the ground station and the satellite. In this context, it is desirable to have onboard fault-diagnosis system that is capable of detecting, isolating, identifying or classifying faults in the system withouttheinvolvementandinterventionofoperators.Towardthisend,theprinciple goal here is to improve the ef?ciency, accuracy, and reliability of the trend analysis and diagnostics techniques through utilization of intelligent-based and hybrid-based methodologies.
Download or read book Artificial Intelligence in Process Fault Diagnosis written by Richard J. Fickelscherer and published by John Wiley & Sons. This book was released on 2024-02-21 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt: Artificial Intelligence in Process Fault Diagnosis A comprehensive guide to the future of process fault diagnosis Automation has revolutionized every aspect of industrial production, from the accumulation of raw materials to quality control inspections. Even process analysis itself has become subject to automated efficiencies, in the form of process fault analyzers, i.e., computer programs capable of analyzing process plant operations to identify faults, improve safety, and enhance productivity. Prohibitive cost and challenges of application have prevented widespread industry adoption of this technology, but recent advances in artificial intelligence promise to place these programs at the center of manufacturing process analysis. Artificial Intelligence in Process Fault Diagnosis brings together insights from data science and machine learning to deliver an effective introduction to these advances and their potential applications. Balancing theory and practice, it walks readers through the process of choosing an ideal diagnostic methodology and the creation of intelligent computer programs. The result promises to place readers at the forefront of this revolution in manufacturing. Artificial Intelligence in Process Fault Diagnosis readers will also find: Coverage of various AI-based diagnostic methodologies elaborated by leading experts Guidance for creating programs that can prevent catastrophic operating disasters, reduce downtime after emergency process shutdowns, and more Comprehensive overview of optimized best practices Artificial Intelligence in Process Fault Diagnosis is ideal for process control engineers, operating engineers working with processing industrial plants, and plant managers and operators throughout the various process industries.
Download or read book Fault Diagnosis written by Józef Korbicz and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 936 pages. Available in PDF, EPUB and Kindle. Book excerpt: This comprehensive work presents the status and likely development of fault diagnosis, an emerging discipline of modern control engineering. It covers fundamentals of model-based fault diagnosis in a wide context, providing a good introduction to the theoretical foundation and many basic approaches of fault detection.
Download or read book Bond Graph Model based Fault Diagnosis of Hybrid Systems written by Wolfgang Borutzky and published by Springer. This book was released on 2014-11-04 with total page 283 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents bond graph model-based fault detection with a focus on hybrid system models. The book addresses model design, simulation, control and model-based fault diagnosis of multidisciplinary engineering systems. The text beings with a brief survey of the state-of-the-art, then focuses on hybrid systems. The author then uses different bond graph approaches throughout the text and provides case studies.
