Download or read book Potential of Water Injection for Gasoline Engines by Means of a 3D CFD Virtual Test Bench written by Antonino Vacca and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Water injection is one of the most promising technologies to improve the engine combustion efficiency, by mitigating knock occurrences and controlling exhaust gas temperature before turbine. As result, the engine can operate at stoichiometric conditions over the whole engine map, even during the more power-demanding RDE cycles. Antonino Vacca presents a methodology to study and optimize the effect of water injection for gasoline engines by investigating different engine layouts and injection strategies through the set-up of a 3D-CFD virtual test bench. He investigates indirect and direct water injection strategies to increase the engine knock limit and to reduce exhaust gas temperature for several operating points. Contents Influence of Water Vapour on Flame Speed and Auto-Ignition Optimization of the Water Injector Targeting Mixture Formation Induced by Water Injection Water Injection in Combination with Miller Cycle Target Groups Researchers and students in the field of automotive engineering Automotive engineers About the Author Antonino Vacca obtained a PhD at the research Institute of Automotive Engineering (IFS), University of Stuttgart and he is currently project leader at FKFS (Stuttgart, Germany) responsible for the development of innovative combustion concepts for gasoline and gas engines.

Download or read book Potential of Water Injection for Gasoline Engines by Means of a 3D CFD Virtual Test Bench written by Antonino Vacca and published by Springer Nature. This book was released on 2020-12-15 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: Water injection is one of the most promising technologies to improve the engine combustion efficiency, by mitigating knock occurrences and controlling exhaust gas temperature before turbine. As result, the engine can operate at stoichiometric conditions over the whole engine map, even during the more power-demanding RDE cycles. Antonino Vacca presents a methodology to study and optimize the effect of water injection for gasoline engines by investigating different engine layouts and injection strategies through the set-up of a 3D-CFD virtual test bench. He investigates indirect and direct water injection strategies to increase the engine knock limit and to reduce exhaust gas temperature for several operating points.

Download or read book Investigation of Innovative Water Injection Strategies for Gasoline Engines by Means of a 3D CFD Virtual Engine Test Bench written by Edoardo Rossi and published by Springer Nature. This book was released on 2024 with total page 185 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the investigation of innovative engine technologies that can improve the efficiency of internal combustion engines and reduce their environmental impact. In particular, water injection is examined as a means of improving engine behavior. The possible combination of water injection with renewable fuels is also a topic of the book. The results of this experimental and numerical research show positive results that can be used for further research and development of engines. Content 3D-CFD Simulation Environment: the Virtual Engine Test Bench Experimental Spray Analysis and 3D-CFD Injection Model Calibration Applicability of Water Injection in Combination with an eFuel Water-in-Fuel Emulsions at the Virtual Engine Test Bench Target Groups Students and researchers in the field of automotive engineering, esp. engine technology Engineers in the automotive industry About the Author Edoardo Rossi is a project manager in the virtual engine development department at the FKFS, where he did his PhD. He works on innovative solutions for future powertrain technologies for motor vehicles. .

Download or read book Emission Reduction with an Alternative Diesel Combustion Process written by Marvin Sascha Wahl and published by Springer Nature. This book was released on 2023-07-29 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: Marvin Sascha Wahl presents the possibilities for optimising diesel engine combustion. In the advanced process of partially premixed diesel combustion, nitrogen oxide and soot emissions can be minimised at the same time. A new feature is the possibility of applying this strategy up to 2000 revolutions and 10 bar indicated mean pressure. In this work, various effective parameters are also compared and correlated with each other. A final comparison with conventional diesel combustion shows the advantages and disadvantages and evaluates them.

Download or read book A Simulative Approach to Predict Energy Consumption of Future Powertrain Configurations for the Year 2040 written by Tobias Stoll and published by Springer Nature. This book was released on 2023-07-29 with total page 245 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book deals with the simulative prediction of efficiency and CO2-emissions of future powertrain systems for the year 2040. For this purpose, a suitable simulation environment is first created. This is followed by a technology extrapolation of all relevant powertrain systems, for example: combustion engines, electric drives, fuel cells as well as all relevant additional components. These components are then used to build 57 vehicle variants for the simulation. Finally, extensive simulations of the vehicle variants are carried out, evaluated and compared. Comprehensive tables of results are available for all simulated vehicle variants. The evaluations are of interest to anyone concerned with energy consumption and CO2-emissions of future vehicles.

Download or read book Analysis of Injection Processes in an Innovative 3D CFD Tool for the Simulation of Internal Combustion Engines written by Marlene Wentsch and published by Springer. This book was released on 2018-05-16 with total page 155 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to the large number of influencing parameters and interactions, the fuel injection and therewith fuel propagation and distribution are among the most complex processes in an internal combustion engine. For this reason, injection is usually the subject to highly detailed numerical modeling, which leads to unacceptably high computing times in the 3D-CFD simulation of a full engine domain. Marlene Wentsch presents a critical analysis, optimization and extension of injection modeling in an innovative, fast response 3D-CFD tool that is exclusively dedicated to the virtual development of internal combustion engines. About the Author Marlene Wentsch works as research associate in the field of 3D-CFD simulations of injection processes at the Institute of Internal Combustion Engines and Automotive Engineering (IVK), University of Stuttgart, Germany.

Download or read book Modeling of End Gas Autoignition for Knock Prediction in Gasoline Engines written by Andreas Manz and published by Logos Verlag Berlin GmbH. This book was released on 2016-08-18 with total page 263 pages. Available in PDF, EPUB and Kindle. Book excerpt: Downsizing of modern gasoline engines with direct injection is a key concept for achieving future CO22 emission targets. However, high power densities and optimum efficiency are limited by an uncontrolled autoignition of the unburned air-fuel mixture, the so-called spark knock phenomena. By a combination of three-dimensional Computational Fluid Dynamics (3D-CFD) and experiments incorporating optical diagnostics, this work presents an integral approach for predicting combustion and autoignition in Spark Ignition (SI) engines. The turbulent premixed combustion and flame front propagation in 3D-CFD is modeled with the G-equation combustion model, i.e. a laminar flamelet approach, in combination with the level set method. Autoignition in the unburned gas zone is modeled with the Shell model based on reduced chemical reactions using optimized reaction rate coefficients for different octane numbers (ON) as well as engine relevant pressures, temperatures and EGR rates. The basic functionality and sensitivities of improved sub-models, e.g. laminar flame speed, are proven in simplified test cases followed by adequate engine test cases. It is shown that the G-equation combustion model performs well even on unstructured grids with polyhedral cells and coarse grid resolution. The validation of the knock model with respect to temporal and spatial knock onset is done with fiber optical spark plug measurements and statistical evaluation of individual knocking cycles with a frequency based pressure analysis. The results show a good correlation with the Shell autoignition relevant species in the simulation. The combined model approach with G-equation and Shell autoignition in an active formulation enables a realistic representation of thin flame fronts and hence the thermodynamic conditions prior to knocking by taking into account the ignition chemistry in unburned gas, temperature fluctuations and self-acceleration effects due to pre-reactions. By the modeling approach and simulation methodology presented in this work the overall predictive capability for the virtual development of future knockproof SI engines is improved.

Download or read book Knocking in Gasoline Engines written by Michael Günther and published by Springer. This book was released on 2017-11-21 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book includes the papers presented at the conference discussing approaches to prevent or reliably control knocking and other irregular combustion events. The majority of today’s highly efficient gasoline engines utilize downsizing. High mean pressures produce increased knocking, which frequently results in a reduction in the compression ratio at high specific powers. Beyond this, the phenomenon of pre-ignition has been linked to the rise in specific power in gasoline engines for many years. Charge-diluted concepts with high compression cause extreme knocking, potentially leading to catastrophic failure. The introduction of RDE legislation this year will further grow the requirements for combustion process development, as residual gas scavenging and enrichment to improve the knock limit will be legally restricted despite no relaxation of the need to reach the main center of heat release as early as possible. New solutions in thermodynamics and control engineering are urgently needed to further increase the efficiency of gasoline engines.

Download or read book Annual Index abstracts of SAE Technical Papers written by and published by . This book was released on 2007 with total page 1218 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Common Rail System for GDI Engines written by Giovanni Fiengo and published by Springer Science & Business Media. This book was released on 2012-11-02 with total page 86 pages. Available in PDF, EPUB and Kindle. Book excerpt: Progressive reductions in vehicle emission requirements have forced the automotive industry to invest in research and development of alternative control strategies. Continual control action exerted by a dedicated electronic control unit ensures that best performance in terms of pollutant emissions and power density is married with driveability and diagnostics. Gasoline direct injection (GDI) engine technology is a way to attain these goals. This brief describes the functioning of a GDI engine equipped with a common rail (CR) system, and the devices necessary to run test-bench experiments in detail. The text should prove instructive to researchers in engine control and students are recommended to this brief as their first approach to this technology. Later chapters of the brief relate an innovative strategy designed to assist with the engine management system; injection pressure regulation for fuel pressure stabilization in the CR fuel line is proposed and validated by experiment. The resulting control scheme is composed of a feedback integral action and a static model-based feed-forward action, the gains of which are scheduled as a function of fundamental plant parameters. The tuning of closed-loop performance is supported by an analysis of the phase-margin and the sensitivity function. Experimental results confirm the effectiveness of the control algorithm in regulating the mean-value rail pressure independently from engine working conditions (engine speed and time of injection) with limited design effort.

Download or read book Simulation of a Hydrogen Internal Combustion Engine with Cryogenic Mixture Formation written by Simon Ellgas and published by Cuvillier Verlag. This book was released on 2008-02-25 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is generally accepted that the worldwide change of the climate is caused by the manmade emissions of the greenhouse gas CO2. For this reason the development of new technologies for propulsion aims at the reduction of the CO2-emissions. Using hydrogen as an energy carrier offers the possibility to produce the fuel for vehicles from renewable energy sources, thus avoiding the emission of CO2 completely. The on-board storage of liquid hydrogen at very low(cryogenic) temperatures offers currently the best basis to achieve acceptable cruising ranges of hydrogen vehicles. The consistent utilisation of the cold hydrogen using cryogenic mixture formation offers unique opportunities for the optimisation of a combustion engine with regard to power and efficiency. To fully exploit the potential of this promising mixture formation strategy, the usage of modern simulation techniques is necessary. In the course of this thesis, 1D and 3D computational fluid dynamic simulation tools were brought to a serviceable state ready for the optimisation of a hydrogen engine with cryogenic mixture formation. The simulation of the mixing and the combustion with novel models, adapted for hydrogen engine simulations, was verified by comparison to engine test bench results and optical experiments. Careful model and mesh studies have been performed. The ability of a Turbulent Flame Speed Closure (TFC) combustion model to predict the combustion process for a large part of the engine operating map could be demonstrated. This is a significant progress compared to results achieved until now regarding hydrogen engine simulations. A crucial point of the cryogenic mixture formation is the formation of frost inside the intake port due to the low mixture temperature. For the simulation of this phenomenon, a novel approach to compute frost formation in combination with a 3D CFD simulation has been developed. The validity of the model could be demonstrated on the basis of experimental results reported in literature and by comparison to preexisting cryogenic hydrogen injection experiments. The innovative simulation tool could be applied developing suggestions how to avoid the undesired formation of frost. A simple but robust solution for the frosting issue was elaborated, whose functionality could be demonstrated during engine operation at the test bench, which is regarded as an essential step towards the realisation of a hydrogen engine with cryogenic mixture formation. The presented thesis was conducted at BMW Group Research and Technology in the course of the European funded project HyICE – Optimisation of a Hydrogen Powered Internal Combustion Engine.

Download or read book Potentials of Air Path Variabilities and Water Injection in HD Gas Engines written by Marius Betz and published by . This book was released on 2023 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Mixture Formation in Internal Combustion Engines written by Carsten Baumgarten and published by Springer Science & Business Media. This book was released on 2006-09-28 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: A systematic control of mixture formation with modern high-pressure injection systems enables us to achieve considerable improvements of the combustion pr- ess in terms of reduced fuel consumption and engine-out raw emissions. However, because of the growing number of free parameters due to more flexible injection systems, variable valve trains, the application of different combustion concepts within different regions of the engine map, etc., the prediction of spray and m- ture formation becomes increasingly complex. For this reason, the optimization of the in-cylinder processes using 3D computational fluid dynamics (CFD) becomes increasingly important. In these CFD codes, the detailed modeling of spray and mixture formation is a prerequisite for the correct calculation of the subsequent processes like ignition, combustion and formation of emissions. Although such simulation tools can be viewed as standard tools today, the predictive quality of the sub-models is c- stantly enhanced by a more accurate and detailed modeling of the relevant pr- esses, and by the inclusion of new important mechanisms and effects that come along with the development of new injection systems and have not been cons- ered so far. In this book the most widely used mathematical models for the simulation of spray and mixture formation in 3D CFD calculations are described and discussed. In order to give the reader an introduction into the complex processes, the book starts with a description of the fundamental mechanisms and categories of fuel - jection, spray break-up, and mixture formation in internal combustion engines.

Download or read book Development of a Partially Premixed Combustion Model for a Diesel Engine Using Multiple Injection Strategies written by Rene Thygesen and published by Logos Verlag Berlin GmbH. This book was released on 2012 with total page 157 pages. Available in PDF, EPUB and Kindle. Book excerpt: In order to fulfil future emissions legislations, new combustion systems are to be investigated. One way of improving exhaust emissions is the application of multiple injection strategies and conventional or partially premixed combustion conditions to a Diesel engine. The application of numerical techniques as CFD supports and improves the quality of engine developments. Unfortunately, current spray and combustion models are not accurate enough to simulate multiple injection systems, being in this way a topic of research. The goal of this study was the development of a novel simulation method for the investigation of Diesel engines operated with multiple injection strategies and different combustion modes. The first part of this work focused in improving the spray modelling. The inform ation of 3D CFD simulations of the injector nozzle was introduced in the spray simulation as boundary conditions developing coupling subroutines for this issue. The atomisation modelling was also improved using validated presumed droplet size distributions. Moreover, to avoid the simulation of the injector nozzle for every investigated operating point, a novel interpolating tool was developed in order to create spray boundary conditions based on few 3D CFD simulations of the nozzle under certain initial and boundary conditions. The second part of this thesis dealt with the combustion modelling of Diesel engines. For this issue, a laminar flamelet approach called Representative Interactive Flamelet model (RIF) was selected and implemented. Afterwards, an extended combustion model based on RIF was developed in order to take into account multiple injection strategies. Finally, this new model was validated with a wide range of operating points: applying multiple injection strategies under conventional and partially premixed combustion conditions.

Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Science & Business Media. This book was released on 2010-03-03 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Phenomenology of Diesel Combustion and Modeling Diesel is the most efficient combustion engine today and it plays an important role in transport of goods and passengers on land and on high seas. The emissions must be controlled as stipulated by the society without sacrificing the legendary fuel economy of the diesel engines. These important drivers caused innovations in diesel engineering like re-entrant combustion chambers in the piston, lower swirl support and high pressure injection, in turn reducing the ignition delay and hence the nitric oxides. The limits on emissions are being continually reduced. The- fore, the required accuracy of the models to predict the emissions and efficiency of the engines is high. The phenomenological combustion models based on physical and chemical description of the processes in the engine are practical to describe diesel engine combustion and to carry out parametric studies. This is because the injection process, which can be relatively well predicted, has the dominant effect on mixture formation and subsequent course of combustion. The need for improving these models by incorporating new developments in engine designs is explained in Chapter 2. With “model based control programs” used in the Electronic Control Units of the engines, phenomenological models are assuming more importance now because the detailed CFD based models are too slow to be handled by the Electronic Control Units. Experimental work is necessary to develop the basic understanding of the pr- esses.

Download or read book Two Stroke Cycle Engine written by JohnB. Heywood and published by Routledge. This book was released on 2017-11-01 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses the two-stroke cycle internal combustion engine, used in compact, lightweight form in everything from motorcycles to chainsaws to outboard motors, and in large sizes for marine propulsion and power generation. It first provides an overview of the principles, characteristics, applications, and history of the two-stroke cycle engine, followed by descriptions and evaluations of various types of models that have been developed to predict aspects of two-stroke engine operation.

Download or read book Modeling and Simulation of Knock and Nitric Oxide Emissions in Turbocharged Direct Injection Spark Ignition Engines written by Dirk Linse and published by . This book was released on 2013-11-13 with total page 189 pages. Available in PDF, EPUB and Kindle. Book excerpt: