Download or read book Novel Supercritical Carbon Dioxide Power Cycle Utilizing Pressured Oxy combustion in Conjunction with Cryogenic Compression written by and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The team of Southwest Research Institute® (SwRI) and Thar Energy LLC (Thar) applied technology engineering and economic analysis to evaluate two advanced oxy-combustion power cycles, the Cryogenic Pressurized Oxy-combustion Cycle (CPOC), and the Supercritical Oxy-combustion Cycle. This assessment evaluated the performance and economic cost of the two proposed cycles with carbon capture, and included a technology gap analysis of the proposed technologies to determine the technology readiness level of the cycle and the cycle components. The results of the engineering and economic analysis and the technology gap analysis were used to identify the next steps along the technology development roadmap for the selected cycle. The project objectives, as outlined in the FOA, were 90% CO2 removal at no more than a 35% increase in cost of electricity (COE) as compared to a Supercritical Pulverized Coal Plant without CO2 capture. The supercritical oxy-combustion power cycle with 99% carbon capture achieves a COE of $121/MWe. This revised COE represents a 21% reduction in cost as compared to supercritical steam with 90% carbon capture ($137/MWe). However, this represents a 49% increase in the COE over supercritical steam without carbon capture ($80.95/MWe), exceeding the 35% target. The supercritical oxy-combustion cycle with 99% carbon capture achieved a 37.9% HHV plant efficiency (39.3% LHV plant efficiency), when coupling a supercritical oxy-combustion thermal loop to an indirect supercritical CO2 (sCO2) power block. In this configuration, the power block achieved 48% thermal efficiency for turbine inlet conditions of 650°C and 290 atm. Power block efficiencies near 60% are feasible with higher turbine inlet temperatures, however a design tradeoff to limit firing temperature to 650°C was made in order to use austenitic stainless steels for the high temperature pressure vessels and piping and to minimize the need for advanced turbomachinery features such as blade cooling. The overall technical readiness of the supercritical oxy-combustion cycle is TRL 2, Technology Concept, due to the maturity level of the supercritical oxy-combustor for solid fuels, and several critical supporting components, as identified in the Technical Gap Analysis. The supercritical oxycombustor for solid fuels operating at pressures near 100 atm is a unique component of the supercritical oxy-combustion cycle. In addition to the low TRL supercritical oxy-combustor, secondary systems were identified that would require adaptation for use with the supercritical oxycombustion cycle. These secondary systems include the high pressure pulverized coal feed, high temperature cyclone, removal of post-combustion particulates from the high pressure cyclone underflow stream, and micro-channel heat exchangers tolerant of particulate loading. Bench scale testing was utilized to measure coal combustion properties at elevated pressures in a CO2 environment. This testing included coal slurry preparation, visualization of coal injection into a high pressure fluid, and modification of existing test equipment to facilitate the combustion properties testing. Additional bench scale testing evaluated the effectiveness of a rotary atomizer for injecting a coal-water slurry into a fluid with similar densities, as opposed to the typical application where the high density fluid is injected into a low density fluid. The swirl type supercritical oxy-combustor was developed from initial concept to an advanced design stage through numerical simulation using FLUENT and Chemkin to model the flow through the combustor and provide initial assessment of the coal combustion reactions in the flow path. This effort enabled the initial combustor mechanical layout, initial pressure vessel design, and the conceptual layout of a pilot scale test loop. A pilot scale demonstration of the supercritical oxy-combustion cycle is proposed as the next step in the technology development. This demonstration would ad ...

Download or read book Advanced Power Generation Systems written by Ibrahim Dincer and published by Academic Press. This book was released on 2014-07-15 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Power Generation Systems examines the full range of advanced multiple output thermodynamic cycles that can enable more sustainable and efficient power production from traditional methods, as well as driving the significant gains available from renewable sources. These advanced cycles can harness the by-products of one power generation effort, such as electricity production, to simultaneously create additional energy outputs, such as heat or refrigeration. Gas turbine-based, and industrial waste heat recovery-based combined, cogeneration, and trigeneration cycles are considered in depth, along with Syngas combustion engines, hybrid SOFC/gas turbine engines, and other thermodynamically efficient and environmentally conscious generation technologies. The uses of solar power, biomass, hydrogen, and fuel cells in advanced power generation are considered, within both hybrid and dedicated systems. The detailed energy and exergy analysis of each type of system provided by globally recognized author Dr. Ibrahim Dincer will inform effective and efficient design choices, while emphasizing the pivotal role of new methodologies and models for performance assessment of existing systems. This unique resource gathers information from thermodynamics, fluid mechanics, heat transfer, and energy system design to provide a single-source guide to solving practical power engineering problems. - The only complete source of info on the whole array of multiple output thermodynamic cycles, covering all the design options for environmentally-conscious combined production of electric power, heat, and refrigeration - Offers crucial instruction on realizing more efficiency in traditional power generation systems, and on implementing renewable technologies, including solar, hydrogen, fuel cells, and biomass - Each cycle description clarified through schematic diagrams, and linked to sustainable development scenarios through detailed energy, exergy, and efficiency analyses - Case studies and examples demonstrate how novel systems and performance assessment methods function in practice

Download or read book Fundamentals and Applications of Supercritical Carbon Dioxide SCO2 Based Power Cycles written by Klaus Brun and published by Woodhead Publishing. This book was released on 2017-01-09 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamentals and Applications of Supercritical Carbon Dioxide (SCO2) Based Power Cycles aims to provide engineers and researchers with an authoritative overview of research and technology in this area. Part One introduces the technology and reviews the properties of SCO2 relevant to power cycles. Other sections of the book address components for SCO2 power cycles, such as turbomachinery expanders, compressors, recuperators, and design challenges, such as the need for high-temperature materials. Chapters on key applications, including waste heat, nuclear power, fossil energy, geothermal and concentrated solar power are also included. The final section addresses major international research programs. Readers will learn about the attractive features of SC02 power cycles, which include a lower capital cost potential than the traditional cycle, and the compounding performance benefits from a more efficient thermodynamic cycle on balance of plant requirements, fuel use, and emissions. - Represents the first book to focus exclusively on SC02 power cycles - Contains detailed coverage of cycle fundamentals, key components, and design challenges - Addresses the wide range of applications of SC02 power cycles, from more efficient electricity generation, to ship propulsion

Download or read book Compact Heat Exchangers written by J.E. Hesselgreaves and published by Elsevier. This book was released on 2001-05-08 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the ideas and industrial concepts in compact heat exchanger technology that have been developed in the last 10 years or so. Historically, the development and application of compact heat exchangers and their surfaces has taken place in a piecemeal fashion in a number of rather unrelated areas, principally those of the automotive and prime mover, aerospace, cryogenic and refrigeration sectors. Much detailed technology, familiar in one sector, progressed only slowly over the boundary into another sector. This compartmentalisation was a feature both of the user industries themselves, and also of the supplier, or manufacturing industries. These barriers are now breaking down, with valuable cross-fertilisation taking place. One of the industrial sectors that is waking up to the challenges of compact heat exchangers is that broadly defined as the process sector. If there is a bias in the book, it is towards this sector. Here, in many cases, the technical challenges are severe, since high pressures and temperatures are often involved, and working fluids can be corrosive, reactive or toxic. The opportunities, however, are correspondingly high, since compacts can offer a combination of lower capital or installed cost, lower temperature differences (and hence running costs), and lower inventory. In some cases they give the opportunity for a radical re-think of the process design, by the introduction of process intensification (PI) concepts such as combining process elements in one unit. An example of this is reaction and heat exchange, which offers, among other advantages, significantly lower by-product production.To stimulate future research, the author includes coverage of hitherto neglected approaches, such as that of the Second Law (of Thermodynamics), pioneered by Bejan and co- workers. The justification for this is that there is increasing interest in life-cycle and sustainable approaches to industrial activity as a whole, often involving exergy (Second Law) analysis. Heat exchangers, being fundamental components of energy and process systems, are both savers and spenders of exergy, according to interpretation.

Download or read book Applications of Supercritical Carbon Dioxide Based Power Cycles written by and published by . This book was released on 2018-05 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: Supercritical CO2 (sCO2) cycles are being considered for future fossil energy systems. These sCO2 systems deliver the prospect of improved efficiency combined with smaller turbo -machinery size compared to a traditional Rankine steam system if operated at turbine inlet temperatures up to 760°C. Supercritical CO2 cycles have been investigated since the 1960s, but technical limitations, both computational and physical, prevented major strides on the subject until the turn of the millennium. Since then, numerous studies have investigated and conceptualized various sCO2 cycles: as standalone power cycles for nuclear applications, in concentrated solar power plants or for waste heat recovery. Many of these studies were conducted using established performance simulation tools such as NPSS, which were expanded in their functionality through supercritical CO2 fluid property functions.Fundamentals and Applications of Supercritical Carbon Dioxide (sCO2) Based Power Cycles provides up-to-date information of research and technology in this field. This book addresses components for sCO2 power cycles, such as turbomachinery expanders, compressors, recuperators, and design challenges, such as the need for high-temperature materials. The attractive features of sC02 power cycles are addressed. The supercritical CO2 (sCO2) Brayton cycle has recently been gaining a lot of attention for application to next generation nuclear reactors. The advantages of the sCO2 cycle are high efficiency in the mild turbine inlet temperature region and a small physical footprint with a simple layout, compact turbomachinery, and heat exchangers. Currently sCO2 cycles are being investigated primarily for stationary power applications, but their high power density and efficiency, even for modest peak cycle temperatures, makes them credible bottoming cycle options for aero engine applications. To successfully utilize the high reactor outlet temperature, interest in alternative power conversion systems is also increasing. The steam Rankine cycle and gas turbine systems have been utilized by large size power plants for several decades.This book will appeal to students, practitioners, as well as researchers dealing with this field.

Download or read book A Supercritical Carbon Dioxide Cycle for Next Generation Nuclear Reactors written by Vaclav Dostal and published by . This book was released on 2004 with total page 317 pages. Available in PDF, EPUB and Kindle. Book excerpt: A systematic, detailed major component and system design evaluation and multiple parameter optimization under practical constraints has been performed of the family of supercritical CO2 Brayton power cycles for application to advanced nuclear reactors. The recompression cycle is shown to excel with respect to simplicity, compactness, cost and thermal efficiency. The main advantage of the supercritical CO2 cycle is comparable efficiency with the helium Brayton cycle at significantly lower temperature (550°C vs. 850 0C), but higher pressure (20 MPa vs. 8 MPa). The supercritical CO2 cycle is well suited to any type of nuclear reactor with core outlet temperature above [approx.] 500 0C in either direct or indirect versions. By taking advantage of the abrupt property changes near the critical point of CO2 the compression work can be reduced, which results in a significant efficiency improvement. However, a real gas cycle requires much more careful optimization than an ideal gas Brayton cycle. Previous investigations by earlier authors were systematized and refined in the present work to survey several different CO2 cycle layouts. Inter- cooling, re-heating, re-compressing and pre-compressing were considered. The recompression cycle was found to yield the highest efficiency, while still retaining simplicity. Inter-cooling is not attractive for this type of cycle as it offers a very modest efficiency improvement. Re-heating has a better potential, but it is applicable only to indirect cycles. Economic analysis of the benefit of re-heating for the indirect cycle showed that using more than one stage of re-heat is economically unattractive.

Download or read book High Fidelity Simulations of Supercritical CO2 Based Oxy Combustion with Non Ideal Equation of State written by and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The supercritical carbon dioxide (sCO2) Allam-Fetvedt cycle employs high-temperature oxy-combustion using sCO2 as the working fluid, leading to a unique and challenging environment for materials. In this cycle, pressurized gaseous fuel is combusted in the presence of a hot oxidant flow containing a mixture of CO2 and oxygen and a hot CO2 diluent recycle stream at approximately 300 bar under lean combustion conditions. We present high-fidelity reacting simulations of this oxy-combustor environment and compare the results when performing simulations with ideal and non-ideal equations of state. By doing so, we identify if the combustor behavior at the regime of interest is sensitive enough to the equation of state to justify the added computational cost incurred with a non-ideal equation of state.

Download or read book Solid Particle Erosion and Erosion corrosion of Materials written by Alan V. Levy and published by ASM International. This book was released on 1995-01-01 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: Contents include: Mechanism of Erosion - Effects of Mechanical Properties of Metals on Erosion - Effects of Erodent Particle Characteristics on the Erosion of Steel - Erosion and Erosion Corrosion of Steels at Elevated Temperatures - Erosion Corrosion of Materials in Elevated - Temperature Service and more.

Download or read book Pressurized fluidized bed combustion written by National Research Development Corporation and published by . This book was released on 1976 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Evaluation and Optimization of a Supercritical Carbon Dioxide Power Conversion Cycle for Nuclear Applications written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: There have been a number of studies involving the use of gases operating in the supercritical mode for power production and process heat applications. Supercritical carbon dioxide (CO2) is particularly attractive because it is capable of achieving relatively high power conversion cycle efficiencies in the temperature range between 550°C and 750°C. Therefore, it has the potential for use with any type of high-temperature nuclear reactor concept, assuming reactor core outlet temperatures of at least 550°C. The particular power cycle investigated in this paper is a supercritical CO2 Recompression Brayton Cycle. The CO2 Recompression Brayton Cycle can be used as either a direct or indirect power conversion cycle, depending on the reactor type and reactor outlet temperature. The advantage of this cycle when compared to the helium Brayton Cycle is the lower required operating temperature; 550°C versus 850°C. However, the supercritical CO2 Recompression Brayton Cycle requires an operating pressure in the range of 20 MPa, which is considerably higher than the required helium Brayton cycle operating pressure of 8 MPa. This paper presents results of analyses performed using the UniSim process analyses software to evaluate the performance of the supercritical CO2 Brayton Recompression Cycle for different reactor outlet temperatures. The UniSim model assumed a 600 MWt reactor power source, which provides heat to the power cycle at a maximum temperature of between 550°C and 750°C. The UniSim model used realistic component parameters and operating conditions to model the complete power conversion system. CO2 properties were evaluated, and the operating range for the cycle was adjusted to take advantage of the rapidly changing conditions near the critical point. The UniSim model was then optimized to maximize the power cycle thermal efficiency at the different maximum power cycle operating temperatures. The results of the analyses showed that power cycle thermal efficiencies in the range of 40 to 50% can be achieved.

Download or read book Techno economic Analysis of Pressurized Oxy fuel Combustion Power Cycle for CO2 Capture written by Jongsup Hong and published by . This book was released on 2009 with total page 254 pages. Available in PDF, EPUB and Kindle. Book excerpt: (cont.) We calculate the energy requirements of each unit and determine the pressure dependence of the water-condensing thermal energy recovery and its relation to the gross power output. Furthermore, a sensitivity analysis is conducted on important operating parameters including combustor temperature, Heat Recovery Steam Generator outlet temperature, oxygen purity and oxygen concentration in the flue gases. A cost analysis of the proposed system is also conducted so as to provide preliminary cost estimates.

Download or read book Modeling the Supercritical Carbon Dioxide Brayton Cycle with Recompression written by and published by . This book was released on 2014 with total page 155 pages. Available in PDF, EPUB and Kindle. Book excerpt: Supercritical carbon dioxide (SCO2) power cycles show promise for a wide range of applications, such as concentrating solar power, next-generation nuclear reactors, and waste-heat recovery. Models capable of predicting the design-point, off-design, and part-load performance of SCO2 power cycles are necessary for evaluating cycle designs. These models should be flexible in order to accommodate the range of designs under consideration and computationally efficient in order to enable timely optimization studies, possibly while considering cycle performance on an annual or life-cycle basis. This document reports on the development of a modeling framework that accommodates these requirements and is capable of predicting the performance of recuperated and recompression cycle configurations. The modeling framework is in Fortran and is flexible with respect to component-level specifics, such as the type of compressor used in the cycle or the method used to represent the off-design performance of the turbine. Optimization routines are integrated into the models, allowing exploration of optimal component and system designs or optimal operating strategies for a given system design. The optimal design-point and off-design performance of various cycle designs is predicted using turbomachinery models based on the radial compressors and turbines that are currently being investigated by Sandia National Laboratory for use in SCO2 applications. A range of heat rejection (low-side) temperatures are considered and results indicate that operating the cycles at warmer low-side temperatures requires a corresponding increase in low-side pressure in order to maximize thermal efficiency. The relationship between low-side temperature and pressure suggests that inventory control (i.e., actively controlling the low-side pressure) is a favorable control mechanism, especially if the power plant is expected to operate away from its design point for significant periods of time. For cycles designed to operate at warmer heat rejection temperatures (e.g., a dry-cooled design in an arid climate), the benefits of recompression are reduced and a simple recuperated cycle may be favorable. The optimal SCO2 Brayton cycle design depends on the application being considered, and the developed modeling framework provides the consistent performance predictions that are required for further application-specific analyses.

Download or read book Advanced Supercritical Carbon Dioxide Power Cycle Configurations for Use in Concentrating Solar Power Systems written by Zhiwen Ma and published by . This book was released on 2011 with total page 4 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the proposed design, a single-phase process using supercritical carbon dioxide (S-CO2) as both heat transfer fluid (HTF) and thermal power cycle fluid simplifies the power system configuration. The design is compatible with sensible-heat thermal energy storage, if desired. The simpler machinery and compact size of the S-CO2 process may also reduce the installation, maintenance and operation cost of the system. Brayton-cycle systems using S-CO2 have smaller weight and volume, lower thermal mass, and less complex power blocks versus Rankine cycles due to the higher density of the fluid and simpler cycle design. The lower thermal mass makes startup and load change faster for frequent start up/shut down operations and load adaption than a HTF/steam based system. The research will characterize and evaluate advanced S-CO2 Brayton cycle power generation with a modular power tower CSP system.

Download or read book Optimization and Comparison of Direct and Indirect Supercritical Carbon Dioxide Power Plant Cycles for Nuclear Applications written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: There have been a number of studies involving the use of gases operating in the supercritical mode for power production and process heat applications. Supercritical carbon dioxide (CO2) is particularly attractive because it is capable of achieving relatively high power conversion cycle efficiencies in the temperature range between 550 C and 750 C. Therefore, it has the potential for use with any type of high-temperature nuclear reactor concept, assuming reactor core outlet temperatures of at least 550 C. The particular power cycle investigated in this paper is a supercritical CO2 Recompression Brayton Cycle. The CO2 Recompression Brayton Cycle can be used as either a direct or indirect power conversion cycle, depending on the reactor type and reactor outlet temperature. The advantage of this cycle when compared to the helium Brayton cycle is the lower required operating temperature; 550 C versus 850 C. However, the supercritical CO2 Recompression Brayton Cycle requires an operating pressure in the range of 20 MPa, which is considerably higher than the required helium Brayton cycle operating pressure of 8 MPa. This paper presents results of analyses performed using the UniSim process analyses software to evaluate the performance of both a direct and indirect supercritical CO2 Brayton Recompression cycle for different reactor outlet temperatures. The direct supercritical CO2 cycle transferred heat directly from a 600 MWt reactor to the supercritical CO2 working fluid supplied to the turbine generator at approximately 20 MPa. The indirect supercritical CO2 cycle assumed a helium-cooled Very High Temperature Reactor (VHTR), operating at a primary system pressure of approximately 7.0 MPa, delivered heat through an intermediate heat exchanger to the secondary indirect supercritical CO2 Brayton Recompression cycle, again operating at a pressure of about 20 MPa. For both the direct and indirect cycles, sensitivity calculations were performed for reactor outlet temperature between 550 C and 850 C. The UniSim models used realistic component parameters and operating conditions to model the complete reactor and power conversion systems. CO2 properties were evaluated, and the operating ranges of the cycles were adjusted to take advantage of the rapidly changing properties of CO2 near the critical point. The results of the analyses showed that, for the direct supercritical CO2 power cycle, thermal efficiencies in the range of 40 to 50% can be achieved. For the indirect supercritical CO2 power cycle, thermal efficiencies were approximately 10% lower than those obtained for the direct cycle over the same reactor outlet temperature range.

Download or read book Negative Emissions Technologies and Reliable Sequestration written by National Academies of Sciences, Engineering, and Medicine and published by National Academies Press. This book was released on 2019-04-08 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: To achieve goals for climate and economic growth, "negative emissions technologies" (NETs) that remove and sequester carbon dioxide from the air will need to play a significant role in mitigating climate change. Unlike carbon capture and storage technologies that remove carbon dioxide emissions directly from large point sources such as coal power plants, NETs remove carbon dioxide directly from the atmosphere or enhance natural carbon sinks. Storing the carbon dioxide from NETs has the same impact on the atmosphere and climate as simultaneously preventing an equal amount of carbon dioxide from being emitted. Recent analyses found that deploying NETs may be less expensive and less disruptive than reducing some emissions, such as a substantial portion of agricultural and land-use emissions and some transportation emissions. In 2015, the National Academies published Climate Intervention: Carbon Dioxide Removal and Reliable Sequestration, which described and initially assessed NETs and sequestration technologies. This report acknowledged the relative paucity of research on NETs and recommended development of a research agenda that covers all aspects of NETs from fundamental science to full-scale deployment. To address this need, Negative Emissions Technologies and Reliable Sequestration: A Research Agenda assesses the benefits, risks, and "sustainable scale potential" for NETs and sequestration. This report also defines the essential components of a research and development program, including its estimated costs and potential impact.

Download or read book Geologic Carbon Sequestration written by V. Vishal and published by Springer. This book was released on 2016-05-11 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: This exclusive compilation written by eminent experts from more than ten countries, outlines the processes and methods for geologic sequestration in different sinks. It discusses and highlights the details of individual storage types, including recent advances in the science and technology of carbon storage. The topic is of immense interest to geoscientists, reservoir engineers, environmentalists and researchers from the scientific and industrial communities working on the methodologies for carbon dioxide storage. Increasing concentrations of anthropogenic carbon dioxide in the atmosphere are often held responsible for the rising temperature of the globe. Geologic sequestration prevents atmospheric release of the waste greenhouse gases by storing them underground for geologically significant periods of time. The book addresses the need for an understanding of carbon reservoir characteristics and behavior. Other book volumes on carbon capture, utilization and storage (CCUS) attempt to cover the entire process of CCUS, but the topic of geologic sequestration is not discussed in detail. This book focuses on the recent trends and up-to-date information on different storage rock types, ranging from deep saline aquifers to coal to basaltic formations.

Download or read book Advances in Carbon Capture written by Mohammad Reza Rahimpour and published by Woodhead Publishing. This book was released on 2020-08-04 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Carbon Capture reviews major implementations of CO2 capture, including absorption, adsorption, permeation and biological techniques. For each approach, key benefits and drawbacks of separation methods and technologies, perspectives on CO2 reuse and conversion, and pathways for future CO2 capture research are explored in depth. The work presents a comprehensive comparison of capture technologies. In addition, the alternatives for CO2 separation from various feeds are investigated based on process economics, flexibility, industrial aspects, purification level and environmental viewpoints. - Explores key CO2 separation and compare technologies in terms of provable advantages and limitations - Analyzes all critical CO2 capture methods in tandem with related technologies - Introduces a panorama of various applications of CO2 capture