Download or read book New Approaches to Scaled up Carbon Nanotube Synthesis and Nanotube based Metal Composites and Sensors written by Amit Goyal and published by . This book was released on 2007 with total page 255 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first phase of the work presented in this dissertation is the development of a scaleable process for the cost-effective synthesis of single walled carbon nanotubes (SWNTs) by thermally-induced catalytic chemical vapor deposition (CVD). With the goal of understanding the growth mechanism and optimize the synthesis process, the effect of CVD and catalyst parameters on nanotube formation was investigated in detail. It was found that nucleation and growth of SWNTs occurred within a few seconds of the introduction of the carbon source, carbon monoxide, at temperatures above 675°C over a Co-Mo/MgO catalyst/support system, resulting in the formation of high quality thinly bundled SWNTs with a narrow individual nanotube diameter distribution. A simple kinetic model is proposed to explain the observed growth and exit gas (CO2) concentration data. A scaled up run using fluidized bed reactor is performed to demonstrate large SWNTs production. In the second phase of the research performed some of the CVD parameters optimized for the synthesis of pure nanotubes were used to infiltrate SWNTs as well as multiwalled carbon nanotubes (MWNTs) into catalyst precursor filled iron and aluminum matrices, respectively, to directly fabricate metal-nanotube composites. Two carbon sources, carbon monoxide and acetylene were used for the synthesis of SWNTs and MWNTs, respectively. The yield strength of iron-carbon nanotube composites showed substantial enhancement of up to 45% and 36 % with 1 wt % of infiltrated SWNTs and MWNTs, respectively, relative to that of similarly treated pure iron samples of the same piece density without carbon nanotubes. Vickers hardness measurements showed an increase of 74% and 96% for iron composites filled with SWNTs and MWNTs, respectively. The use of a mixed feed of CO and acetylene resulted in carbide-free fabrication of the nanocomposites. A reaction mechanism supporting the observed carbide-free growth is also presented. In the third phase of the research performed, a SWNT fabrication protocol using CVD growth or electrophoretic deposition was employed for integrating nanotubes as biosensor and chemical gas sensor probes. For biosensor probes, vertically aligned SWNTs were grown or deposited on metal interconnects (Cr/Co), at precise locations, which were patterned on quartz substrates using photo- and e-beam Iithogrpahy to make electrical connections to each SWNT/bundle individually. Gas sensor probes were fabricated using individually suspended SWNTs contacted by Cr/Au pads as source and drain field effect transistor components for the monitoring of NO2 vapors. The adsorption of an electron donating gas such as NO2 on the SWNT sidewalls shifts the Fermi level of the p-type semiconducting nanotubes, consequently changing their electrical conductivity. Experimental results showed that sensor response to NO2 (at 10-300 ppm levels) was of the order of a few seconds at 100 ppm, and was reversible and reproducible. Recovery of the sensor response was achieved by heating the sensors at 120 °C for a period of 10-12 hours indicating physisorption of the NO2 molecules on the nanotube sidewalls.
Download or read book Carbon Nanotube Science written by Peter J. F. Harris and published by Cambridge University Press. This book was released on 2009-03-19 with total page 315 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes represent one of the most exciting research areas in modern science. These molecular-scale carbon tubes are the stiffest and strongest fibres known, with remarkable electronic properties, and potential applications in a wide range of fields. Carbon Nanotube Science is a concise, accessible book, presenting the basic knowledge that graduates and researchers need to know. Based on the successful Carbon Nanotubes and Related Structures, this book focuses solely on carbon nanotubes, covering the major advances made in recent years in this rapidly developing field. Chapters focus on electronic properties, chemical and bimolecular functionalisation, nanotube composites and nanotube-based probes and sensors. The book begins with a comprehensive discussion of synthesis, purification and processing methods. With its comprehensive coverage of this active research field, this book will appeal to researchers in a broad range of disciplines, including nanotechnology, engineering, materials science and physics.
Download or read book Fundamentals of Conjugated Polymer Blends Copolymers and Composites written by Parveen Saini and published by John Wiley & Sons. This book was released on 2015-04-30 with total page 684 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since their discovery in 1977, the evolution of conducting polymers has revolutionized modern science and technology. These polymers enjoy a special status in the area of materials science yet they are not as popular among young readers or common people when compared to other materials like metals, paper, plastics, rubber, textiles, ceramics and composites like concrete. Most importantly, much of the available literature in the form of papers, specific review articles and books is targeted either at advanced readers (scientists / technologists / engineers / senior academicians) or for those who are already familiar with the topic (doctoral / postdoctoral scholars). For a beginner or even school / college students, such compilations are bit difficult to access / digest. In fact, they need proper introduction to the topic of conducting polymers including their discovery, preparation, properties, applications and societal impact, using suitable examples and already known principles/knowledge/phenomenon. Further, active participation of readers in terms of "question & answers", "fill-in-the-blanks", "numerical" along with suitable answer key is necessary to maintain the interest and to initiate the "thought process". The readers also need to know about the drawbacks and any hazards of such materials. Therefore, I believe that a comprehensive source on the science / technology of conducting polymers which maintains a link between grass root fundamentals and state-of-the-art R&D is still missing from the open literature.
Download or read book Syntheses and Applications of Carbon Nanotubes and Their Composites written by Satoru Suzuki and published by BoD – Books on Demand. This book was released on 2013-05-09 with total page 552 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes are rolled up graphene sheets with a quasi-one-dimensional structure of nanometer-scale diameter. In these last twenty years, carbon nanotubes have attracted much attention from physicists, chemists, material scientists, and electronic device engineers, because of their excellent structural, electronic, optical, chemical and mechanical properties. More recently, demand for innovative industrial applications of carbon nanotubes is increasing. This book covers recent research topics regarding syntheses techniques of carbon nanotubes and nanotube-based composites, and their applications. The chapters in this book will be helpful to many students, engineers and researchers working in the field of carbon nanotubes.
Download or read book Nanotube Superfiber Materials written by Mark Schulz and published by William Andrew. This book was released on 2013-09-16 with total page 861 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanotube Superfiber Materials refers to different forms of macroscale materials with unique properties constructed from carbon nanotubes. These materials include nanotube arrays, ribbons, scrolls, yarn, braid, and sheets. Nanotube materials are in the early stage of development and this is the first dedicated book on the subject. Transitioning from molecules to materials is a breakthrough that will positively impact almost all industries and areas of society. Key properties of superfiber materials are high flexibility and fatigue resistance, high energy absorption, high strength, good electrical conductivity, high maximum current density, reduced skin and proximity effects, high thermal conductivity, lightweight, good field emission, piezoresistive, magnetoresistive, thermoelectric, and other properties. These properties will open up the door to dozens of applications including replacing copper wire for power conduction, EMI shielding, coax cable, carbon biofiber, bullet-proof vests, impact resistant glass, wearable antennas, biomedical microdevices, biosensors, self-sensing composites, supercapacitors, superinductors, hybrid superconductor, reinforced elastomers, nerve scaffolding, energy storage, and many others. The scope of the book covers three main areas: Part I: Processing; Part II: Properties; and Part III: Applications. Processing involves nanotube synthesis and macro scale material formation methods. Properties covers the mechanical, electrical, chemical and other properties of nanotubes and macroscale materials. Different approaches to growing high quality long nanotubes and spinning the nanotubes into yarn are explained in detail. The best ideas are collected from all around the world including commercial approaches. Applications of nanotube superfiber cover a huge field and provides a broad survey of uses. The book gives a broad overview starting from bioelectronics to carbon industrial machines. - First book to explore the production and applications of macro-scale materials made from nano-scale particles - Sets out the processes for producing macro-scale materials from carbon nanotubes, and describes the unique properties of these materials - Potential applications for CNT fiber/yarn include replacing copper wire for power conduction, EMI shielding, coax cable, carbon biofiber, bullet-proof vests, impact resistant glass, wearable antennas, biomedical microdevices, biosensors, self-sensing composites, supercapacitors, superinductors, hybrid superconductor, reinforced elastomers, nerve scaffolding, energy storage, and many others
Download or read book Carbon Nanotubes for a Green Environment written by Shrikaant Kulkarni and published by CRC Press. This book was released on 2022-06-30 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon Nanotubes for a Green Environment: Balancing the Risks and Rewards describes the synthesis, characterization, and unique applications of undoped and doped carbon nanotubes as well as hybrids of them with grapheme or nanocomposites, focusing on green aspects of carbon nanotube applications. The volume shows new approaches used for tapping the potential and promise of key materials in isolation or combined with other materials. The research-oriented chapters highlight a spectrum of applications of carbon nanotubes as novel materials for energy storage as well as for environmental remediation, wastewater treatment, green health care products, and more. Chapters explore the use of carbon nanotubes for remediation methods for wastewater treatment such as by using graphene oxide-carbon nanotube composites and by applying undoped and doped carbon nanotubes for removing contaminates. The book also looks at the application of carbon nanotubes for enhanced oil recovery and for heavy metal separation. Other chapters look at the rheological behavior of carbon nanotubes-based materials and their role in processing for various products, the thermal and electrical transport in carbon nanotubes composites, carbon nanotubes-based composite materials for electromagnetic shielding applications. The biomedical applications of carbon nanotube-based nanomaterials also explored, such as FTIR spectroscopy.
Download or read book Carbon Composites written by Eduardo A. Castro and published by CRC Press. This book was released on 2023-05-31 with total page 338 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the innovative methodologies and strategies adopted in carbon materials research area including: Synthesis, characterization, and functionalization of carbon nanotubes and graphene Surface modification of graphene Carbon-based nanostructured materials The use of carbon nanomaterials for energy applications Development of carbon nanotubes reinforced metal matrix composites and non-metallic composites and their myriad potential end-use applications Key challenges to the successful and widespread implementation of carbon nanotubes reinforced metal matrix composites and non-metallic composites Methods for quantification and improved control of carbon nanotubes distributions Recent research and design trends for carbon nanomaterials-based sensors for a variety of applications Advances and potential applications in environmental monitoring and healthcare
Download or read book Carbon Nanotubes written by Arvind Agarwal and published by CRC Press. This book was released on 2017-06-20 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: From the Foreword, written by legendary nano pioneer M. Meyyappan, Chief Scientist for Exploration Technology NASA Ames Research Center, Moffett Field, California, USA: ..".there is critical need for a book to summarize the status of the field but more importantly to lay out the principles behind the technology. This is what Professor Arvind Agarwal and his co-workers ... have done here." Carbon Nanotubes: Reinforced Metal Matrix Composites reflects the authors' desire to share the benefits of nanotechnology with the masses by developing metal matrix carbon nanotube (MM-CNT) composites for large-scale applications. Multiwall carbon nanotubes can now be produced on a large scale and at a significantly reduced cost. The book explores potential applications and applies the author's own research to highlight critical developmental issues for different MM-CNT composites--and then outline novel solutions. With this problem-solving approach, the book explores: Advantages, limitations, and the evolution of processing techniques used for MM-CNT composites Characterization techniques unique to the study of MM-CNT composites--and the limitations of these methods Existing research on different MM-CNT composites, presented in useful tables that include composition, processing method, quality of CNT dispersion, and properties The micro-mechanical strengthening that results from adding CNT The applicability of micro-mechanics models in MM-CNT composites Significance of chemical stability for carbon nanotubes in the metal matrix as a function of processing, and its impact on CNT/metal interface and mechanical properties Computational studies that have not been sufficiently covered although they are essential to research and development The critical issue of CNT dispersion in the metal matrix, as well as a unique way to quantify CNT distribution and subsequently improve control of the processing parameters for obtaining improved properties Carbon Nanotubes: Reinforced Metal Matrix Composites paints a vivid picture of scientific and application achievements in this field. Exploring the mechanisms through which CNTs are enhancing the properties of different metal-based composites, the authors provide a roadmap to help researchers develop MM-CNT composites and choose potential materials for use in emerging areas of technology.
Download or read book Carbon Nanotubes written by Andy Nieto and published by CRC Press. This book was released on 2021-05-18 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt: This discovery of carbon nanotubes (CNT) three decades ago ushered in the technological era of nanotechnology. Among the most widely studied areas of CNT research is their use as structural reinforcements in composites. This book describes the development of CNT reinforced metal matrix composites (CNT-MMCs) over the last two decades. The field of CNT-MMCs is abundant in fundamental science, rich in engineering challenges and innovations and ripe for technological maturation and commercialization. The authors have sought to present the current state of the-art in CNT-MMC technology from their synthesis to their myriad potential end-use applications. Specifically, topics explored include: • Advantages, limitations, and evolution of processing techniques used to synthesize and fabricate CNT-MMCs • Emphasizes dispersion techniques of CNTs in metallic systems, a key challenge to the successful and widespread implementation of CNT-MMCs. Methods for quantification and improved control of CNT distributions are presented • Methods for quantification and improved control of CNT distributions are presented • Characterization techniques uniquely suited for charactering these nanoscale materials and their many chemical and physical interactions with the metal matrix, including real-time in-situ characterization of deformation mechanisms • Electron microscope images from premier studies enrich discussions on micro-mechanical modeling, interfacial design, mechanical behavior, and functional properties • A chapter is dedicated to the emergence of dual reinforcement composites that seek to enhance the efficacy of CNTs and lead to material properties by design This book highlights seminal findings in CNT-MMC research and includes several tables listing processing methods, associated CNT states, and resulting properties in order to aid the next generation of researchers in advancing the science and engineering of CNT-MMCs. In addition, a survey of the patent literature is presented in order to shed light on what the first wave of CNT-MMC commercialization may look like and the challenges that will have to be overcome, both technologically and commercially.
Download or read book Perspective of Carbon Nanotubes written by Hosam El-Din Saleh and published by BoD – Books on Demand. This book was released on 2019-12-11 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes belong to new nanomaterials and have been known for almost 20 years, but their history is somewhat lengthier. They have been identified as promising candidates for various applications.High-temperature preparation techniques are conventional techniques for the synthesis of carbon nanotubes using arc discharge or laser ablation, but today these methods are being replaced by low-temperature vapor deposition techniques, since orientation, alignment, nanotube length, diameter, purity, and density of carbon nanotubes can be precisely controlled. The synthesis of carbon nanotubes by chemical vapor deposition on catalyst arrays leads to nanotube models grown from specific sites on surfaces. The controlled synthesis of nanotubes opens up interesting possibilities in nanoscience and nanotechnologies, including electrical, mechanical and electromechanical properties and devices, chemical functionalization, surface chemistry and photochemistry, molecular sensors, and interfacing with moderate biological systems.Carbon nanotubes are used in many applications due to their unique electrical, mechanical, optical, thermal, and other properties. Conductive and high-strength composite materials, energy saving and energy conversion devices, sensors, visualization of field emissions and sources of radiation, means for storing hydrogen, and nanoscale semiconductor devices, probes, and interconnections are some of the many applications of carbon nanotubes.
Download or read book Carbon Nanotubes written by A. K. HAGHI and published by Apple Academic Press. This book was released on 2021-03-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the diversity of recent advances in carbon nanotubes from a broad perspective that will be useful for scientists as well as for graduate students and engineers. Presenting leading-edge research in this dynamic field, this volume is an introduction to the physical concepts needed for investigating carbon nanotubes and other one-dimensional solid-state systems. Written for a wide scientific readership, each chapter consists of an instructive approach to the topic and sustainable ideas for solutions. Carbon nanotubes, with their extraordinary mechanical and unique electronic properties, have garnered much attention in recent years. With a broad range of potential applications, including nanoelectronics, composites, chemical sensors, biosensors, microscopy, nanoelectromechanical systems, and many more, the scientific community is more motivated than ever to move beyond basic properties and explore the real issues associated with carbon nanotube-based applications. Carbon nanotubes are exceptionally interesting from a fundamental research point of view. They open up new perspectives for various applications, such as nano-transistors in circuits, field-emission displays, artificial muscles, or added reinforcements in alloys. This book reviews the recent progress in modeling of carbon nanotubes and their composites. The advantages and disadvantages of different methods are discussed. The ability of continuum methods to bridge different scales is emphasized. Recommendations for future research are given by focusing on what each method has to learn from the nano-scale. The scope of the book is to provide current knowledge aiming to support researchers entering the scientific area of carbon nanotubes to choose the appropriate modeling tool for accomplishing their study and place their efforts to further improve continuum methods.
Download or read book Carbon Nanotube Reinforced Composites written by Sie Chin Tjong and published by John Wiley & Sons. This book was released on 2009-04-08 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing a broad insight into the potential applications of carbon nanotubes with metals and ceramic materials as a matrix, this book focuses on the preparation and the microstructural, physical, and mechanical characterizations of such novel nanocomposites. It features information on current synthesis and structure-property-relationships of metals and ceramics reinforced with CNT, organizing the vast array of surveys scattered throughout the literature in a single monograph. With its laboratory protocols and data tables this is invaluable reading for research workers and academics, as well as for applied scientists and industry personnel.
Download or read book Characterization of Carbon Nanotube Based Composites under Consideration of Defects written by Moones Rahmandoust and published by Springer. This book was released on 2015-10-14 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents the characterization methods involved with carbon nanotubes and carbon nanotube-based composites, with a more detailed look at computational mechanics approaches, namely the finite element method. Special emphasis is placed on studies that consider the extent to which imperfections in the structure of the nanomaterials affect their mechanical properties. These defects may include random distribution of fibers in the composite structure, as well as atom vacancies, perturbation and doping in the structure of individual carbon nanotubes.
Download or read book Carbon Nanotubes and Related Structures written by Dirk M. Guldi and published by John Wiley & Sons. This book was released on 2010-01-26 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by the most prominent experts and pioneers in the field, this ready reference combines fundamental research, recent breakthroughs and real-life applications in one well-organized treatise. As such, both newcomers and established researchers will find here a wide range of current methods for producing and characterizing carbon nanotubes using imaging as well as spectroscopic techniques. One major part of this thorough overview is devoted to the controlled chemical functionalization of carbon nanotubes, covering intriguing applications in photovoltaics, organic electronics and materials design. The latest research on novel carbon-derived structures, such as graphene, nanoonions and carbon pea pods, round off the book.
Download or read book Carbon Nanotube Based Composites written by Antonio Pantano and published by Smithers Rapra. This book was released on 2012-09-28 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes (CNTs) have amazing properties and a key way to take advantage of this is by incorporating nanotubes into a matrix to build composite materials. The best candidates for this task are undoubtedly polymers. Almost every characteristic of a polymer can be significantly enhanced by adding carbon nanotubes and as a result, new potential applications of carbon nanotube enhanced polymer composites are discovered every day. However, before carbon nanotube enhanced polymer composites become commonplace there are some tough challenges that need to be overcome. This book reviews the status of worldwide research in both single-walled and multi-walled carbon nanotube based composites. It serves as a practical guide on carbon nanotube based composites and a reference to students and researchers from the academia and industry.
Download or read book Syntheses and Applications of Carbon Nanotubes and Their Composites written by Satoru Suzuki and published by . This book was released on 2013 with total page 550 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes are rolled up graphene sheets with a quasi-one-dimensional structure of nanometer-scale diameter. In these last twenty years, carbon nanotubes have attracted much attention from physicists, chemists, material scientists, and electronic device engineers, because of their excellent structural, electronic, optical, chemical and mechanical properties. More recently, demand for innovative industrial applications of carbon nanotubes is increasing. This book covers recent research topics regarding syntheses techniques of carbon nanotubes and nanotube-based composites, and their applications. The chapters in this book will be helpful to many students, engineers and researchers working in the field of carbon nanotubes.
Download or read book Aligned Carbon Nanotubes written by Zhifeng Ren and published by Springer Science & Business Media. This book was released on 2012-09-05 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives a survey of the physics and fabrication of carbon nanotubes and their applications in optics, electronics, chemistry and biotechnology. It focuses on the structural characterization of various carbon nanotubes, fabrication of vertically or parallel aligned carbon nanotubes on substrates or in composites, physical properties for their alignment, and applications of aligned carbon nanotubes in field emission, optical antennas, light transmission, solar cells, chemical devices, bio-devices, and many others. Major fabrication methods are illustrated in detail, particularly the most widely used PECVD growth technique on which various device integration schemes are based, followed by applications such as electrical interconnects, nanodiodes, optical antennas, and nanocoax solar cells, whereas current limitations and challenges are also be discussed to lay the foundation for future developments.
