Download or read book Multicore Systems On Chip Practical Software Hardware Design written by Abderazek Ben Abdallah and published by Springer Science & Business Media. This book was released on 2013-07-20 with total page 291 pages. Available in PDF, EPUB and Kindle. Book excerpt: System on chips designs have evolved from fairly simple unicore, single memory designs to complex heterogeneous multicore SoC architectures consisting of a large number of IP blocks on the same silicon. To meet high computational demands posed by latest consumer electronic devices, most current systems are based on such paradigm, which represents a real revolution in many aspects in computing. The attraction of multicore processing for power reduction is compelling. By splitting a set of tasks among multiple processor cores, the operating frequency necessary for each core can be reduced, allowing to reduce the voltage on each core. Because dynamic power is proportional to the frequency and to the square of the voltage, we get a big gain, even though we may have more cores running. As more and more cores are integrated into these designs to share the ever increasing processing load, the main challenges lie in efficient memory hierarchy, scalable system interconnect, new programming paradigms, and efficient integration methodology for connecting such heterogeneous cores into a single system capable of leveraging their individual flexibility. Current design methods tend toward mixed HW/SW co-designs targeting multicore systems on-chip for specific applications. To decide on the lowest cost mix of cores, designers must iteratively map the device’s functionality to a particular HW/SW partition and target architectures. In addition, to connect the heterogeneous cores, the architecture requires high performance complex communication architectures and efficient communication protocols, such as hierarchical bus, point-to-point connection, or Network-on-Chip. Software development also becomes far more complex due to the difficulties in breaking a single processing task into multiple parts that can be processed separately and then reassembled later. This reflects the fact that certain processor jobs cannot be easily parallelized to run concurrently on multiple processing cores and that load balancing between processing cores – especially heterogeneous cores – is very difficult.

Download or read book MULTICORE SYSTEMS ON CHIP written by Ben Abadallah Abderazek and published by Springer Science & Business Media. This book was released on 2010-08-01 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt: Conventional on-chip communication design mostly use ad-hoc approaches that fail to meet the challenges posed by the next-generation MultiCore Systems on-chip (MCSoC) designs. These major challenges include wiring delay, predictability, diverse interconnection architectures, and power dissipation. A Network-on-Chip (NoC) paradigm is emerging as the solution for the problems of interconnecting dozens of cores into a single system on-chip. However, there are many problems associated with the design of such systems. These problems arise from non-scalable global wire delays, failure to achieve global synchronization, and difficulties associated with non-scalable bus-based functional interconnects. The book consists of three parts, with each part being subdivided into four chapters. The first part deals with design and methodology issues. The architectures used in conventional methods of MCSoCs design and custom multiprocessor architectures are not flexible enough to meet the requirements of different application domains and not scalable enough to meet different computation needs and different complexities of various applications. Several chapters of the first part will emphasize on the design techniques and methodologies. The second part covers the most critical part of MCSoCs design — the interconnections. One approach to addressing the design methodologies is to adopt the so-called reusability feature to boost design productivity. In the past years, the primitive design units evolved from transistors to gates, finite state machines, and processor cores. The network-on-chip paradigm offers this attractive property for the future and will be able to close the productivity gap. The last part of this book delves into MCSoCs validations and optimizations. A more qualitative approach of system validation is based on the use of formal techniques for hardware design. The main advantage of formal methods is the possibility to prove the validity of essential design requirements. As formal languages have a mathematical foundation, it is possible to formally extract and verify these desired properties of the complete abstract state space. Online testing techniques for identifying faults that can lead to system failure are also surveyed. Emphasis is given to analytical redundancy-based techniques that have been developed for fault detection and isolation in the automatic control area.

Download or read book Applied Reconfigurable Computing Architectures Tools and Applications written by Nikolaos Voros and published by Springer. This book was released on 2018-04-25 with total page 761 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book constitutes the proceedings of the 14th International Conference on Applied Reconfigurable Computing, ARC 2018, held in Santorini, Greece, in May 2018. The 29 full papers and 22 short presented in this volume were carefully reviewed and selected from 78 submissions. In addition, the volume contains 9 contributions from research projects. The papers were organized in topical sections named: machine learning and neural networks; FPGA-based design and CGRA optimizations; applications and surveys; fault-tolerance, security and communication architectures; reconfigurable and adaptive architectures; design methods and fast prototyping; FPGA-based design and applications; and special session: research projects.

Download or read book Analytical Modelling in Parallel and Distributed Computing written by Peter Hanuliak and published by Chartridge Books Oxford. This book was released on 2014 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: This publication examines complex performance evaluation of various typical parallel algorithms (shared memory, distributed memory) and their practical implementations. As real application examples we demonstrate the various influences during the process of modelling and performance evaluation and the consequences of their distributed parallel implementations.

Download or read book Computer Vision and Action Recognition written by Md. Atiqur Rahman Ahad and published by Springer Science & Business Media. This book was released on 2011-12-02 with total page 228 pages. Available in PDF, EPUB and Kindle. Book excerpt: Human action analyses and recognition are challenging problems due to large variations in human motion and appearance, camera viewpoint and environment settings. The field of action and activity representation and recognition is relatively old, yet not well-understood by the students and research community. Some important but common motion recognition problems are even now unsolved properly by the computer vision community. However, in the last decade, a number of good approaches are proposed and evaluated subsequently by many researchers. Among those methods, some methods get significant attention from many researchers in the computer vision field due to their better robustness and performance. This book will cover gap of information and materials on comprehensive outlook – through various strategies from the scratch to the state-of-the-art on computer vision regarding action recognition approaches. This book will target the students and researchers who have knowledge on image processing at a basic level and would like to explore more on this area and do research. The step by step methodologies will encourage one to move forward for a comprehensive knowledge on computer vision for recognizing various human actions.

Download or read book Trustworthy Ubiquitous Computing written by Ismail Khalil and published by Springer Science & Business Media. This book was released on 2012-09-08 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: Trustworthy Ubiquitous Computing covers aspects of trust in ubiquitous computing environments. The aspects of context, privacy, reliability, usability and user experience related to “emerged and exciting new computing paradigm of Ubiquitous Computing”, includes pervasive, grid, and peer-to-peer computing including sensor networks to provide secure computing and communication services at anytime and anywhere. Marc Weiser presented his vision of disappearing and ubiquitous computing more than 15 years ago. The big picture of the computer introduced into our environment was a big innovation and the starting point for various areas of research. In order to totally adopt the idea of ubiquitous computing several houses were build, equipped with technology and used as laboratory in order to find and test appliances that are useful and could be made available in our everyday life. Within the last years industry picked up the idea of integrating ubiquitous computing and already available products like remote controls for your house were developed and brought to the market. In spite of many applications and projects in the area of ubiquitous and pervasive computing the success is still far away. One of the main reasons is the lack of acceptance of and confidence in this technology. Although researchers and industry are working in all of these areas a forum to elaborate security, reliability and privacy issues, that resolve in trustworthy interfaces and computing environments for people interacting within these ubiquitous environments is important. The user experience factor of trust thus becomes a crucial issue for the success of a UbiComp application. The goal of this book is to provide a state the art of Trustworthy Ubiquitous Computing to address recent research results and to present and discuss the ideas, theories, technologies, systems, tools, applications and experiences on all theoretical and practical issues.

Download or read book Activity Recognition in Pervasive Intelligent Environments written by Liming Chen and published by Springer Science & Business Media. This book was released on 2011-05-04 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book consists of a number of chapters addressing different aspects of activity recognition, roughly in three main categories of topics. The first topic will be focused on activity modeling, representation and reasoning using mathematical models, knowledge representation formalisms and AI techniques. The second topic will concentrate on activity recognition methods and algorithms. Apart from traditional methods based on data mining and machine learning, we are particularly interested in novel approaches, such as the ontology-based approach, that facilitate data integration, sharing and automatic/automated processing. In the third topic we intend to cover novel architectures and frameworks for activity recognition, which are scalable and applicable to large scale distributed dynamic environments. In addition, this topic will also include the underpinning technological infrastructure, i.e. tools and APIs, that supports function/capability sharing and reuse, and rapid development and deployment of technological solutions. The fourth category of topic will be dedicated to representative applications of activity recognition in intelligent environments, which address the life cycle of activity recognition and their use for novel functions of the end-user systems with comprehensive implementation, prototyping and evaluation. This will include a wide range of application scenarios, such as smart homes, intelligent conference venues and cars.

Download or read book A Practical Introduction to Hardware Software Codesign written by Patrick R. Schaumont and published by Springer Science & Business Media. This book was released on 2010-09-09 with total page 403 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a practical book for computer engineers who want to understand or implement hardware/software systems. It focuses on problems that require one to combine hardware design with software design – such problems can be solved with hardware/software codesign. When used properly, hardware/software co- sign works better than hardware design or software design alone: it can improve the overall performance of digital systems, and it can shorten their design time. Hardware/software codesign can help a designer to make trade-offs between the ?exibility and the performanceof a digital system. To achieve this, a designer needs to combine two radically different ways of design: the sequential way of dec- position in time, using software, with the parallel way of decomposition in space, using hardware. Intended Audience This book assumes that you have a basic understandingof hardware that you are - miliar with standard digital hardware componentssuch as registers, logic gates, and components such as multiplexers and arithmetic operators. The book also assumes that you know how to write a program in C. These topics are usually covered in an introductory course on computer engineering or in a combination of courses on digital design and software engineering.

Download or read book Embedded Memory Design for Multi Core and Systems on Chip written by Baker Mohammad and published by Springer Science & Business Media. This book was released on 2013-10-22 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes the various tradeoffs systems designers face when designing embedded memory. Readers designing multi-core systems and systems on chip will benefit from the discussion of different topics from memory architecture, array organization, circuit design techniques and design for test. The presentation enables a multi-disciplinary approach to chip design, which bridges the gap between the architecture level and circuit level, in order to address yield, reliability and power-related issues for embedded memory.

Download or read book Photonic Interconnects for Computing Systems written by Gabriela Nicolescu and published by CRC Press. This book was released on 2022-09-01 with total page 453 pages. Available in PDF, EPUB and Kindle. Book excerpt: In recent years, there has been a considerable amount of effort, both in industry and academia, focusing on the design, implementation, performance analysis, evaluation and prediction of silicon photonic interconnects for inter- and intra-chip communication, paving the way for the design and dimensioning of the next and future generation of high-performance computing systems. Photonic Interconnects for Computing Systems provides a comprehensive overview of the current state-of-the-art technology and research achievements in employing silicon photonics for interconnection networks and high-performance computing, summarizing main opportunities and some challenges. The majority of the chapters were collected from presentations made at the International Workshop on Optical/Photonic Interconnects for Computing Systems (OPTICS) held over the past two years. The workshop invites internationally recognized speakers on the range of topics relevant to silicon photonics and computing systems. Technical topics discussed in the book include:Design and Implementation of Chip-Scale Photonic Interconnects;Developing Design Automation Solutions for Chip-Scale Photonic Interconnects;Design Space Exploration in Chip-Scale Photonic Interconnects;Thermal Analysis and Modeling in Photonic Interconnects;Design for Reliability;Fabrication Non-Uniformity in Photonic Interconnects;Photonic Interconnects for Computing Systems presents a compilation of outstanding contributions from leading research groups in the field. It presents a comprehensive overview of the design, advantages, challenges, and requirements of photonic interconnects for computing systems. The selected contributions present important discussions and approaches related to the design and development of novel photonic interconnect architectures, as well as various design solutions to improve the performance of such systems while considering different challenges. The book is ideal for personnel in computer/photonic industries as well as academic staff and master/graduate students in computer science and engineering, electronic engineering, electrical engineering and photonics.

Download or read book Processor and System on Chip Simulation written by Rainer Leupers and published by Springer Science & Business Media. This book was released on 2010-09-15 with total page 343 pages. Available in PDF, EPUB and Kindle. Book excerpt: Simulation of computer architectures has made rapid progress recently. The primary application areas are hardware/software performance estimation and optimization as well as functional and timing verification. Recent, innovative technologies such as retargetable simulator generation, dynamic binary translation, or sampling simulation have enabled widespread use of processor and system-on-chip (SoC) simulation tools in the semiconductor and embedded system industries. Simultaneously, processor and SoC simulation is still a very active research area, e.g. what amounts to higher simulation speed, flexibility, and accuracy/speed trade-offs. This book presents and discusses the principle technologies and state-of-the-art in high-level hardware architecture simulation, both at the processor and the system-on-chip level.

Download or read book Three Plays of Maureen Hunter written by Hunter, Maureen and published by OIBooks-Libros. This book was released on 2003 with total page 944 pages. Available in PDF, EPUB and Kindle. Book excerpt: Book is clean and tight. No writing in text. Like New

Download or read book Principles and Practice of Constraint Programming written by Peter J. Stuckey and published by Springer. This book was released on 2008-09-22 with total page 662 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains the proceedings of the 14th International Conference on Principles and Practice of Constraint Programming (CP 2008) held in Sydney, Australia, September 14–18, 2008. The conference was held in conjunction with the International Conference on Automated Planning and Scheduling (ICAPS 2008) and the International Conference on Knowledge Representation and R- soning (KR 2008). Information about the conference can be found at the w- sitehttp://www. unimelb. edu. au/cp2008/. Held annually, the CP conference series is the premier international conference on constraint programming. The conference focuses on all aspects of computing with constraints. The CP conf- ence series is organized by the Association for Constraint Programming (ACP). Information about the conferences in the series can be found on the Web at http://www. cs. ualberta. ca/~ai/cp/. Information about ACP can be found athttp://www. a4cp. org/. CP 2008 included two calls for contributions: a call for research papers, - scribing novel contributions in the ?eld, and a call for application papers, - scribing applications of constraint technology. For the ?rst time authors could directly submit short papers for consideration by the committee. The research track received 84 long submissions and 21 short submissions and the application track received 15 long submissions. Each paper received at least three reviews, which the authors had the opportunity to see and to react to, before the papers and their reviews were discussed extensively by the members of the Program Committee.

Download or read book Software Engineering for Embedded Systems written by Robert Oshana and published by Newnes. This book was released on 2013-04-01 with total page 1201 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Expert Guide gives you the techniques and technologies in software engineering to optimally design and implement your embedded system. Written by experts with a solutions focus, this encyclopedic reference gives you an indispensable aid to tackling the day-to-day problems when using software engineering methods to develop your embedded systems. With this book you will learn: - The principles of good architecture for an embedded system - Design practices to help make your embedded project successful - Details on principles that are often a part of embedded systems, including digital signal processing, safety-critical principles, and development processes - Techniques for setting up a performance engineering strategy for your embedded system software - How to develop user interfaces for embedded systems - Strategies for testing and deploying your embedded system, and ensuring quality development processes - Practical techniques for optimizing embedded software for performance, memory, and power - Advanced guidelines for developing multicore software for embedded systems - How to develop embedded software for networking, storage, and automotive segments - How to manage the embedded development process Includes contributions from: Frank Schirrmeister, Shelly Gretlein, Bruce Douglass, Erich Styger, Gary Stringham, Jean Labrosse, Jim Trudeau, Mike Brogioli, Mark Pitchford, Catalin Dan Udma, Markus Levy, Pete Wilson, Whit Waldo, Inga Harris, Xinxin Yang, Srinivasa Addepalli, Andrew McKay, Mark Kraeling and Robert Oshana. - Road map of key problems/issues and references to their solution in the text - Review of core methods in the context of how to apply them - Examples demonstrating timeless implementation details - Short and to- the- point case studies show how key ideas can be implemented, the rationale for choices made, and design guidelines and trade-offs

Download or read book Embedded Computing Systems Applications Optimization and Advanced Design written by Khalgui, Mohamed and published by IGI Global. This book was released on 2013-04-30 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Embedded computing systems play an important and complex role in the functionality of electronic devices. With our daily routines becoming more reliant on electronics for personal and professional use, the understanding of these computing systems is crucial. Embedded Computing Systems: Applications, Optimization, and Advanced Design brings together theoretical and technical concepts of intelligent embedded control systems and their use in hardware and software architectures. By highlighting formal modeling, execution models, and optimal implementations, this reference source is essential for experts, researchers, and technical supporters in the industry and academia.

Download or read book Programming Many Core Chips written by András Vajda and published by Springer Science & Business Media. This book was released on 2011-06-10 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents new concepts, techniques and promising programming models for designing software for chips with "many" (hundreds to thousands) processor cores. Given the scale of parallelism inherent to these chips, software designers face new challenges in terms of operating systems, middleware and applications. This will serve as an invaluable, single-source reference to the state-of-the-art in programming many-core chips. Coverage includes many-core architectures, operating systems, middleware, and programming models.

Download or read book Design of Cost Efficient Interconnect Processing Units written by Marcello Coppola and published by CRC Press. This book was released on 2020-10-14 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Streamlined Design Solutions Specifically for NoC To solve critical network-on-chip (NoC) architecture and design problems related to structure, performance and modularity, engineers generally rely on guidance from the abundance of literature about better-understood system-level interconnection networks. However, on-chip networks present several distinct challenges that require novel and specialized solutions not found in the tried-and-true system-level techniques. A Balanced Analysis of NoC Architecture As the first detailed description of the commercial Spidergon STNoC architecture, Design of Cost-Efficient Interconnect Processing Units: Spidergon STNoC examines the highly regarded, cost-cutting technology that is set to replace well-known shared bus architectures, such as STBus, for demanding multiprocessor system-on-chip (SoC) applications. Employing a balanced, well-organized structure, simple teaching methods, numerous illustrations, and easy-to-understand examples, the authors explain: how the SoC and NoC technology works why developers designed it the way they did the system-level design methodology and tools used to configure the Spidergon STNoC architecture differences in cost structure between NoCs and system-level networks From professionals in computer sciences, electrical engineering, and other related fields, to semiconductor vendors and investors – all readers will appreciate the encyclopedic treatment of background NoC information ranging from CMPs to the basics of interconnection networks. The text introduces innovative system-level design methodology and tools for efficient design space exploration and topology selection. It also provides a wealth of key theoretical and practical MPSoC and NoC topics, such as technological deep sub-micron effects, homogeneous and heterogeneous processor architectures, multicore SoC, interconnect processing units, generic NoC components, and embeddings of common communication patterns.