Download or read book Heating and Evaporation of Multi Component Fuel Droplets written by Mansour Al Qubeissi and published by BoD – Books on Demand. This book was released on 2015-08-01 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book documents pioneering mathematical models introduced for the simulation of multi-component droplets heating and evaporation processes which are implementable into commercial CFD codes. These models, described as 'multi-dimensional quasi discrete' (MDQD) and 'discrete-component' models, were applied to automotive fuel droplets in experimentally measured internal combustion engine conditions for biodiesel, diesel, and gasoline fuels. For instance, it is shown that the suggested models lead to accurate predictions of temperatures and evaporation times in typical diesel and gasoline engine conditions. Such models have also reduced CPU time about 85% compared with cases when classical approaches are used.
Download or read book Handbook of Physical Properties of Liquids and Gases written by N.B. Vargaftik and published by Springer. This book was released on 2014-04-13 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides numerical data on physical and thermodynamic properties of a large number of elements and compounds. SI units are used throughout, and in addition, an adequate set of conversion tables is included. This volume will be a valuable source of reference for physical chemists and chemical engineers.
Download or read book Fluid Dynamics and Transport of Droplets and Sprays written by W. A. Sirignano and published by Cambridge University Press. This book was released on 1999-07-28 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: An authoritative review of the science and technology of droplets and sprays.
Download or read book Transport Phenomena with Drops and Bubbles written by Satwindar S. Sadhal and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 528 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fluid flows that transfer heat and mass often involve drops and bubbles, particularly if there are changes of phase in the fluid in the formation or condensation of steam, for example. Such flows pose problems for the chemical and mechanical engineer significantly different from those posed by single-phase flows. This book reviews the current state of the field and will serve as a reference for researchers, engineers, teachers, and students concerned with transport phenomena. It begins with a review of the basics of fluid flow and a discussion of the shapes and sizes of fluid particles and the factors that determine these. The discussion then turns to flows at low Reynolds numbers, including effects due to phase changes or to large radial inertia. Flows at intermediate and high Reynolds numbers are treated from a numerical perspective, with reference to experimental results. The next chapter considers the effects of solid walls on fluid particles, treating both the statics and dynamics of the particle-wall interaction and the effects of phase changes at a solid wall. This is followed by a discussion of the formation and breakup of drops and bubbles, both with and without phase changes. The last two chapters discuss compound drops and bubbles, primarily in three-phase systems, and special topics, such as transport in an electric field.
Download or read book Atomization and Sprays written by Arthur H. Lefebvre and published by CRC Press. This book was released on 2017-03-27 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of this long-time bestseller provides a framework for designing and understanding sprays for a wide array of engineering applications. The text contains correlations and design tools that can be easily understood and used in relating the design of atomizers to the resulting spray behavior. Written to be accessible to readers with a modest technical background, the emphasis is on application rather than in-depth theory. Numerous examples are provided to serve as starting points for using the information in the book. Overall, this is a thoroughly updated edition that still retains the practical focus and readability of the original work by Arthur Lefebvre.
Download or read book Advances in Heat Transfer written by and published by Academic Press. This book was released on 1995-05-25 with total page 347 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Heat Transfer is designed to fill the information gap between regularly scheduled journals and university level textbooks by providing in-depth review articles over a broader scope than is allowablein either journals or texts.
Download or read book Fluid Dynamics and Transport of Droplets and Sprays written by W. A. Sirignano and published by Cambridge University Press. This book was released on 2010-01-11 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book discusses the theoretical foundations of spray and droplet applications relevant to the technology for active control of sprays applied to new products and applications, improved product performance, cost reductions, and improved environmental outcomes. It also covers theory related to power and propulsion; materials processing and manufacturing technologies including droplet-based net form processing, coating, and painting; medication; pesticides and insecticides; and other consumer uses.
Download or read book Droplets and Sprays Simple Models of Complex Processes written by Sergei S. Sazhin and published by Springer Nature. This book was released on 2022-06-28 with total page 603 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book acts as a guide to simple models that describe some of the complex fluid dynamics, heat/mass transfer and combustion processes in droplets and sprays. Attention is focused mainly on the use of classical hydrodynamics, and a combination of kinetic and hydrodynamic models, to analyse the heating and evaporation of mono- and multi-component droplets. The models were developed for cases when small and large numbers of components are present in droplets. Some of these models are used for the prediction of time to puffing/micro-explosion of composite water/fuel droplets — processes that are widely used in combustion devices to stimulate disintegration of relatively large droplets into smaller ones. The predictions of numerical codes based on these models are validated against experimental results where possible. In most of the models, droplets are assumed to be spherical; some preliminary results of the generalisation of these models to the case of non-spherical droplets, approximating them as spheroids, are presented.
Download or read book Modeling of Multicomponent Fuels with Application to Sprays and Simulation of Diesel Engine Cold Start written by Andreas M. Lippert and published by . This book was released on 1999 with total page 728 pages. Available in PDF, EPUB and Kindle. Book excerpt: May 1999
Download or read book An Integrated Approach to Spray Combustion Model Development written by W. A. Sirignano and published by . This book was released on 1986 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Internal Combustion Processes of Liquid Rocket Engines written by Zhen-Guo Wang and published by John Wiley & Sons. This book was released on 2016-05-17 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book concentrates on modeling and numerical simulations of combustion in liquid rocket engines, covering liquid propellant atomization, evaporation of liquid droplets, turbulent flows, turbulent combustion, heat transfer, and combustion instability. It presents some state of the art models and numerical methodologies in this area. The book can be categorized into two parts. Part 1 describes the modeling for each subtopic of the combustion process in the liquid rocket engines. Part 2 presents detailed numerical methodology and several representative applications in simulations of rocket engine combustion.
Download or read book Combustion Theory written by Forman A. Williams and published by CRC Press. This book was released on 2018-03-05 with total page 549 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion Theory delves deeper into the science of combustion than most other texts and gives insight into combustions from a molecular and a continuum point of view. The book presents derivations of the basic equations of combustion theory and contains appendices on the background of subjects of thermodynamics, chemical kinetics, fluid dynamics, and transport processes. Diffusion flames, reactions in flows with negligible transport and the theory of pre-mixed flames are treated, as are detonation phenomena, the combustion of solid propellents, and ignition, extinction, and flamibility pehnomena.
Download or read book Droplet Interactions and Spray Processes written by Grazia Lamanna and published by Springer Nature. This book was released on 2020-03-14 with total page 312 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a selection of contributions to the DIPSI workshop 2019 (Droplet Impact Phenomena & Spray Investigations) as well as recent progress of the Int. Research Training Group “DROPIT”.The DIPSI workshop, which is now at its thirteenth edition, represents an important opportunity to share recent knowledge on droplets and sprays in a variety of research fields and industrial applications. The research training group “DROPIT” is focused on droplet interaction technologies where microscopic effects influence strongly macroscopic behavior. This requires the inclusion of interface kinetics and/or a detailed analysis of surface microstructures. Normally, complicated technical processes cover the underlying basic mechanisms, and therefore, progress in the overall process modelling can hardly be gained. Therefore, DROPIT focuses on the underlying basic processes. This is done by investigating different spatial and/or temporal scales of the problems and by linking them through a multi-scale approach. In addition, multi-physics are required to understand e.g. problems for droplet-wall interactions, where porous structures are involved.
Download or read book Principles of Convective Heat Transfer written by Massoud Kaviany and published by Springer Science & Business Media. This book was released on 2001-05-11 with total page 742 pages. Available in PDF, EPUB and Kindle. Book excerpt: This concise and unified text reviews recent contributions to the principles of convective heat transfer for single and multi-phase systems. This valuable new edition has been updated throughout and contains new examples and problems.
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1987 with total page 934 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Droplets and Sprays written by Sergei Sazhin and published by Springer. This book was released on 2014-05-19 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing a clear and systematic description of droplets and spray dynamic models, this book maximises reader insight into the underlying physics of the processes involved, outlines the development of new physical and mathematical models and broadens understanding of interactions between the complex physical processes which take place in sprays. Complementing approaches based on the direct application of computational fluid dynamics (CFD), Droplets and Sprays treats both theoretical and practical aspects of internal combustion engine process such as the direct injection of liquid fuel, subcritical heating and evaporation. Including case studies that illustrate the approaches relevance to automotive applications, it is also anticipated that the described models can find use in other areas such as in medicine and environmental science.
Download or read book Direct Contact Heat Transfer written by Frank Kreith and published by Springer Science & Business Media. This book was released on 2013-11-11 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt: to increase the use of direct contact processes, the National Science Foundation sup ported a workshop on direct contact heat transfer at the Solar Energy Research Insti tute in the summer of 1985. We served as organizers for this workshop, which em phasized an area of thermal engineering that, in our opinion, has great promise for the future, but has not yet reached the point of wide-spread commercial application. Hence, a summary of the state of knowledge at this point is timely. The workshop had a dual objective: 1. To summarize the current state of knowledge in such a form that industrial practi tioners can make use of the available information. 2. To indicate the research and development needed to advance the state-of-the-art, indicating not only what kind of research is needed, but also the industrial poten tial that could be realized if the information to be obtained through the proposed research activities were available.
