Download or read book Hot Carrier Degradation in Semiconductor Devices written by Tibor Grasser and published by Springer. This book was released on 2014-10-29 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides readers with a variety of tools to address the challenges posed by hot carrier degradation, one of today’s most complicated reliability issues in semiconductor devices. Coverage includes an explanation of carrier transport within devices and book-keeping of how they acquire energy (“become hot”), interaction of an ensemble of colder and hotter carriers with defect precursors, which eventually leads to the creation of a defect, and a description of how these defects interact with the device, degrading its performance.

Download or read book Hot Carrier Reliability of MOS VLSI Circuits written by Yusuf Leblebici and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 223 pages. Available in PDF, EPUB and Kindle. Book excerpt: As the complexity and the density of VLSI chips increase with shrinking design rules, the evaluation of long-term reliability of MOS VLSI circuits is becoming an important problem. The assessment and improvement of reliability on the circuit level should be based on both the failure mode analysis and the basic understanding of the physical failure mechanisms observed in integrated circuits. Hot-carrier induced degrada tion of MOS transistor characteristics is one of the primary mechanisms affecting the long-term reliability of MOS VLSI circuits. It is likely to become even more important in future generation chips, since the down ward scaling of transistor dimensions without proportional scaling of the operating voltage aggravates this problem. A thorough understanding of the physical mechanisms leading to hot-carrier related degradation of MOS transistors is a prerequisite for accurate circuit reliability evaluation. It is also being recognized that important reliability concerns other than the post-manufacture reliability qualification need to be addressed rigorously early in the design phase. The development and use of accurate reliability simulation tools are therefore crucial for early assessment and improvement of circuit reliability : Once the long-term reliability of the circuit is estimated through simulation, the results can be compared with predetermined reliability specifications or limits. If the predicted reliability does not satisfy the requirements, appropriate design modifications may be carried out to improve the resistance of the devices to degradation.

Download or read book Characterization Methods for Submicron MOSFETs written by Hisham Haddara and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is true that the Metal-Oxide-Semiconductor Field-Eeffect Transistor (MOSFET) is a key component in modern microelectronics. It is also true that there is a lack of comprehensive books on MOSFET characterization in gen eral. However there is more than that as to the motivation and reasons behind writing this book. During the last decade, device physicists, researchers and engineers have been continuously faced with new elements which made the task of MOSFET characterization more and more crucial as well as difficult. The progressive miniaturization of devices has caused several phenomena to emerge and modify the performance of scaled-down MOSFETs. Localized degradation induced by hot carrier injection and Random Telegraph Signal (RTS) noise generated by individual traps are examples of these phenomena. Therefore, it was inevitable to develop new models and new characterization methods or at least adapt the existing ones to cope with the special nature of these new phenomena. The need for more deep and extensive characterization of MOSFET param eters has further increased as the applications of this device have gained ground in many new fields in which its performance has become more and more sensi tive to the properties of its Si - Si0 interface. MOS transistors have crossed 2 the borders of high speed electronics where they operate at GHz frequencies. Moreover, MOSFETs are now widely employed in the subthreshold regime in neural circuits and biomedical applications.

Download or read book Fundamentals of Bias Temperature Instability in MOS Transistors written by Souvik Mahapatra and published by Springer. This book was released on 2015-08-05 with total page 282 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book aims to cover different aspects of Bias Temperature Instability (BTI). BTI remains as an important reliability concern for CMOS transistors and circuits. Development of BTI resilient technology relies on utilizing artefact-free stress and measurement methods and suitable physics-based models for accurate determination of degradation at end-of-life and understanding the gate insulator process impact on BTI. This book discusses different ultra-fast characterization techniques for recovery artefact free BTI measurements. It also covers different direct measurements techniques to access pre-existing and newly generated gate insulator traps responsible for BTI. The book provides a consistent physical framework for NBTI and PBTI respectively for p- and n- channel MOSFETs, consisting of trap generation and trapping. A physics-based compact model is presented to estimate measured BTI degradation in planar Si MOSFETs having differently processed SiON and HKMG gate insulators, in planar SiGe MOSFETs and also in Si FinFETs. The contents also include a detailed investigation of the gate insulator process dependence of BTI in differently processed SiON and HKMG MOSFETs. The book then goes on to discuss Reaction-Diffusion (RD) model to estimate generation of new traps for DC and AC NBTI stress and Transient Trap Occupancy Model (TTOM) to estimate charge occupancy of generated traps and their contribution to BTI degradation. Finally, a comprehensive NBTI modeling framework including TTOM enabled RD model and hole trapping to predict time evolution of BTI degradation and recovery during and after DC stress for different stress and recovery biases and temperature, during consecutive arbitrary stress and recovery cycles and during AC stress at different frequency and duty cycle. The contents of this book should prove useful to academia and professionals alike.

Download or read book Hot Carrier Effects in MOS Devices written by Eiji Takeda and published by Elsevier. This book was released on 1995-11-28 with total page 329 pages. Available in PDF, EPUB and Kindle. Book excerpt: The exploding number of uses for ultrafast, ultrasmall integrated circuits has increased the importance of hot-carrier effects in manufacturing as well as for other technological applications. They are rapidly movingout of the research lab and into the real world. This book is derived from Dr. Takedas book in Japanese, Hot-Carrier Effects, (published in 1987 by Nikkei Business Publishers). However, the new book is much more than a translation. Takedas original work was a starting point for developing this much more complete and fundamental text on this increasingly important topic. The new work encompasses not only all the latest research and discoveries made in the fast-paced area of hot carriers, but also includes the basics of MOS devices, and the practical considerations related to hot carriers. - Chapter one itself is a comprehensive review of MOS device physics which allows a reader with little background in MOS devices to pick up a sufficient amount of information to be able to follow the rest of the book - The book is written to allow the reader to learn about MOS Device Reliability in a relatively short amount of time, making the texts detailed treatment of hot-carrier effects especially useful and instructive to both researchers and others with varyingamounts of experience in the field - The logical organization of the book begins by discussing known principles, then progresses to empirical information and, finally, to practical solutions - Provides the most complete review of device degradation mechanisms as well as drain engineering methods - Contains the most extensive reference list on the subject

Download or read book MOSFET Models for VLSI Circuit Simulation written by Narain D. Arora and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 628 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal Oxide Semiconductor (MOS) transistors are the basic building block ofMOS integrated circuits (I C). Very Large Scale Integrated (VLSI) circuits using MOS technology have emerged as the dominant technology in the semiconductor industry. Over the past decade, the complexity of MOS IC's has increased at an astonishing rate. This is realized mainly through the reduction of MOS transistor dimensions in addition to the improvements in processing. Today VLSI circuits with over 3 million transistors on a chip, with effective or electrical channel lengths of 0. 5 microns, are in volume production. Designing such complex chips is virtually impossible without simulation tools which help to predict circuit behavior before actual circuits are fabricated. However, the utility of simulators as a tool for the design and analysis of circuits depends on the adequacy of the device models used in the simulator. This problem is further aggravated by the technology trend towards smaller and smaller device dimensions which increases the complexity of the models. There is extensive literature available on modeling these short channel devices. However, there is a lot of confusion too. Often it is not clear what model to use and which model parameter values are important and how to determine them. After working over 15 years in the field of semiconductor device modeling, I have felt the need for a book which can fill the gap between the theory and the practice of MOS transistor modeling. This book is an attempt in that direction.

Download or read book Hot Carrier Design Considerations for MOS Devices and Circuits written by Cheng Wang and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: As device dimensions decrease, hot-carrier effects, which are due mainly to the presence of a high electric field inside the device, are becoming a major design concern. On the one hand, the detrimental effects-such as transconductance degradation and threshold shift-need to be minimized or, if possible, avoided altogether. On the other hand, performance such as the programming efficiency of nonvolatile memories or the carrier velocity inside the devices-need to be maintained or improved through the use of submicron technologies, even in the presence of a reduced power supply. As a result, one of the major challenges facing MOS design engineers today is to harness the hot-carrier effects so that, without sacrificing product performance, degradation can be kept to a minimum and a reli able design obtained. To accomplish this, the physical mechanisms re sponsible for the degradations should first be experimentally identified and characterized. With adequate models thus obtained, steps can be taken to optimize the design, so that an adequate level of quality assur ance in device or circuit performance can be achieved. This book ad dresses these hot-carrier design issues for MOS devices and circuits, and is used primarily as a professional guide for process development engi neers, device engineers, and circuit designers who are interested in the latest developments in hot-carrier degradation modeling and hot-carrier reliability design techniques. It may also be considered as a reference book for graduate students who have some research interests in this excit ing, yet sometime controversial, field.

Download or read book Proceedings of the Symposium on Low Temperature Electronics and High Temperature Superconductors written by and published by . This book was released on 1988 with total page 624 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Injection Phenomena written by Robert K. Willardson and published by . This book was released on 1966 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt: SEMICONDUCTORS & amp; SEMIMETALS V6.

Download or read book Reliability and Failure of Electronic Materials and Devices written by Milton Ohring and published by Elsevier. This book was released on 1998-06-12 with total page 715 pages. Available in PDF, EPUB and Kindle. Book excerpt: Suitable as a reference work for reliability professionals or as a text for advanced undergraduate or graduate students, this book introduces the reader to the widely dispersed reliability literature of microelectronic and electronic-optional devices. Reliability and Failure of Electronic Materials and Devices integrates a treatment of chip and packaging level failures within the context of the atomic mechanisms and models used to explain degradation, and the statistical handling of lifetime data. Electromigration, dielectric radiation damage and the mechanical failure of contacts and solder joints are among the failure mechanisms considered. An underlying thread of the book concerns product defects--their relation to yield and reliability, the role they play in failure, and the way they are experimentally exposed.The reader will gain a deeper physical understanding of failure mechanisms in electronic materials and devices, acquire skills in the mathematical handling of reliability data, and better appreciate future technology trends and the reliability issues they raise. - Discusses reliability and failure on both the chip and packaging levels - Handles the role of defects in yield and reliability - Includes a tutorial chapter on the mathematics of reliability - Focuses on electromigration, dielectric breakdown, hot-electron effects, electrostatic discharge, corrosion, radiation damage and the mechanical failure of packages, contacts, and solder joints - Considers defect detection methods and failure analysis techniques

Download or read book The RF and Microwave Handbook 3 Volume Set written by Mike Golio and published by CRC Press. This book was released on 2018-10-08 with total page 2208 pages. Available in PDF, EPUB and Kindle. Book excerpt: By 1990 the wireless revolution had begun. In late 2000, Mike Golio gave the world a significant tool to use in this revolution: The RF and Microwave Handbook. Since then, wireless technology spread across the globe with unprecedented speed, fueled by 3G and 4G mobile technology and the proliferation of wireless LANs. Updated to reflect this tremendous growth, the second edition of this widely embraced, bestselling handbook divides its coverage conveniently into a set of three books, each focused on a particular aspect of the technology. Six new chapters cover WiMAX, broadband cable, bit error ratio (BER) testing, high-power PAs (power amplifiers), heterojunction bipolar transistors (HBTs), as well as an overview of microwave engineering. Over 100 contributors, with diverse backgrounds in academic, industrial, government, manufacturing, design, and research reflect the breadth and depth of the field. This eclectic mix of contributors ensures that the coverage balances fundamental technical issues with the important business and marketing constraints that define commercial RF and microwave engineering. Focused chapters filled with formulas, charts, graphs, diagrams, and tables make the information easy to locate and apply to practical cases. The new format, three tightly focused volumes, provides not only increased information but also ease of use. You can find the information you need quickly, without wading through material you don’t immediately need, giving you access to the caliber of data you have come to expect in a much more user-friendly format.

Download or read book Strain Engineered MOSFETs written by C.K. Maiti and published by CRC Press. This book was released on 2018-10-03 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: Currently strain engineering is the main technique used to enhance the performance of advanced silicon-based metal-oxide-semiconductor field-effect transistors (MOSFETs). Written from an engineering application standpoint, Strain-Engineered MOSFETs introduces promising strain techniques to fabricate strain-engineered MOSFETs and to methods to assess the applications of these techniques. The book provides the background and physical insight needed to understand new and future developments in the modeling and design of n- and p-MOSFETs at nanoscale. This book focuses on recent developments in strain-engineered MOSFETS implemented in high-mobility substrates such as, Ge, SiGe, strained-Si, ultrathin germanium-on-insulator platforms, combined with high-k insulators and metal-gate. It covers the materials aspects, principles, and design of advanced devices, fabrication, and applications. It also presents a full technology computer aided design (TCAD) methodology for strain-engineering in Si-CMOS technology involving data flow from process simulation to process variability simulation via device simulation and generation of SPICE process compact models for manufacturing for yield optimization. Microelectronics fabrication is facing serious challenges due to the introduction of new materials in manufacturing and fundamental limitations of nanoscale devices that result in increasing unpredictability in the characteristics of the devices. The down scaling of CMOS technologies has brought about the increased variability of key parameters affecting the performance of integrated circuits. This book provides a single text that combines coverage of the strain-engineered MOSFETS and their modeling using TCAD, making it a tool for process technology development and the design of strain-engineered MOSFETs.

Download or read book RF and Microwave Passive and Active Technologies written by Mike Golio and published by CRC Press. This book was released on 2018-10-03 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt: In the high frequency world, the passive technologies required to realize RF and microwave functionality present distinctive challenges. SAW filters, dielectric resonators, MEMS, and waveguide do not have counterparts in the low frequency or digital environment. Even when conventional lumped components can be used in high frequency applications, their behavior does not resemble that observed at lower frequencies. RF and Microwave Passive and Active Technologies provides detailed information about a wide range of component technologies used in modern RF and microwave systems. Updated chapters include new material on such technologies as MEMS, device packaging, surface acoustic wave (SAW) filters, bipolar junction and heterojunction transistors, and high mobility electron transistors (HMETs). The book also features a completely rewritten section on wide bandgap transistors.

Download or read book Essderc 98 written by and published by Atlantica Séguier Frontières. This book was released on 1998 with total page 680 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book BiCMOS Technology and Applications written by Antonio R. Alvarez and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 345 pages. Available in PDF, EPUB and Kindle. Book excerpt: The topic of bipolar compatible CMOS (BiCMOS) is a fascinating one and of ever-growing practical importance. The "technology pendulum" has swung from the two extremes of preeminence of bipolar in the 1950s and 60s to the apparent endless horizons for VLSI NMOS technology during the 1970s and 80s. Yet starting in the 1980s severallimits were clouding the horizon for pure NMOS technology. CMOS reemerged as a· viable high density, high performance technology. Similarly by the mid 1980s scaled bipolar devices had not only demonstrated new high speed records, but early versions of mixed bipolar/CMOS technology were being produced. Hence the paradigm of either high density . Q[ high speed was metamorphasizing into an opportunity for both speed and density via a BiCMOS approach. Now as we approach the 1990s there have been a number of practical demonstrations of BiCMOS both for memory and logic applications and I expect the trend to escalate over the next decade. This book makes a timely contribution to the field of BiCMOS technology and circuit development. The evolution is now indeed rapid so that it is difficult to make such a book exhaustive of current developments. Probably equally difficult is the fact that the new technology opens a range of novel circuit opportunities that are as yet only formative in their development. Given these obstacles it is a herculean task to try to assemble a book on BiCMOS.

Download or read book The Drift Diffusion Equation and Its Applications in MOSFET Modeling written by Wilfried Hänsch and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: To be perfect does not mean that there is nothing to add, but rather there is nothing to take away Antoine de Saint-Exupery The drift-diffusion approximation has served for more than two decades as the cornerstone for the numerical simulation of semiconductor devices. However, the tremendous speed in the development of the semiconductor industry demands numerical simulation tools that are efficient and provide reliable results. This makes the development of a simulation tool an interdisciplinary task in which physics, numerical algorithms, and device technology merge. For the sake of an efficient code there are trade-offs between the different influencing factors. The numerical performance of a program that is highly flexible in device types and the geometries it covers certainly cannot compare with a program that is optimized for one type of device only. Very often the device is sufficiently described by a two dimensional geometry. This is the case in a MOSFET, for example, if the gate length is small compared with the gate width. In these cases the geometry reduces to the specification of a two-dimensional device. Here again the simplest geometries, which are planar or at least rectangular surfaces, will give the most efficient numerical codes. The device engineer has to decide whether this reduced description of the real device is still suitable for his purposes.

Download or read book Simulation of Semiconductor Processes and Devices 1998 written by Kristin De Meyer and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 423 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume contains the proceedings of the 1998 International Conference on Simulation of Semiconductor Processes and Devices and provides an open forum for the presentation of the latest results and trends in modeling and simulation of semiconductor equipment, processes and devices. Topics include: • semiconductor equipment simulation • process modeling and simulation • device modeling and simulation of complex structures • interconnect modeling • integrated systems for process, device, circuit simulation and optimisation • numerical methods and algorithms • compact modeling and parameter extraction • modeling for RF applications • simulation and modeling of new devices (heterojunction based, SET’s, quantum effect devices, laser based ...)