Download or read book Modeling Engine Spray and Combustion Processes written by Gunnar Stiesch and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt: The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Download or read book Introduction to Modeling and Control of Internal Combustion Engine Systems written by Lino Guzzella and published by Springer Science & Business Media. This book was released on 2013-03-14 with total page 303 pages. Available in PDF, EPUB and Kindle. Book excerpt: Internal combustion engines still have a potential for substantial improvements, particularly with regard to fuel efficiency and environmental compatibility. These goals can be achieved with help of control systems. Modeling and Control of Internal Combustion Engines (ICE) addresses these issues by offering an introduction to cost-effective model-based control system design for ICE. The primary emphasis is put on the ICE and its auxiliary devices. Mathematical models for these processes are developed in the text and selected feedforward and feedback control problems are discussed. The appendix contains a summary of the most important controller analysis and design methods, and a case study that analyzes a simplified idle-speed control problem. The book is written for students interested in the design of classical and novel ICE control systems.
Download or read book Engine Modeling and Control written by Rolf Isermann and published by Springer. This book was released on 2016-09-24 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The increasing demands for internal combustion engines with regard to fuel consumption, emissions and driveability lead to more actuators, sensors and complex control functions. A systematic implementation of the electronic control systems requires mathematical models from basic design through simulation to calibration. The book treats physically-based as well as models based experimentally on test benches for gasoline (spark ignition) and diesel (compression ignition) engines and uses them for the design of the different control functions. The main topics are: - Development steps for engine control - Stationary and dynamic experimental modeling - Physical models of intake, combustion, mechanical system, turbocharger, exhaust, cooling, lubrication, drive train - Engine control structures, hardware, software, actuators, sensors, fuel supply, injection system, camshaft - Engine control methods, static and dynamic feedforward and feedback control, calibration and optimization, HiL, RCP, control software development - Control of gasoline engines, control of air/fuel, ignition, knock, idle, coolant, adaptive control functions - Control of diesel engines, combustion models, air flow and exhaust recirculation control, combustion-pressure-based control (HCCI), optimization of feedforward and feedback control, smoke limitation and emission control This book is an introduction to electronic engine management with many practical examples, measurements and research results. It is aimed at advanced students of electrical, mechanical, mechatronic and control engineering and at practicing engineers in the field of combustion engine and automotive engineering.
Download or read book 1D and Multi D Modeling Techniques for IC Engine Simulation written by Angelo Onorati and published by SAE International. This book was released on 2020-04-06 with total page 552 pages. Available in PDF, EPUB and Kindle. Book excerpt: 1D and Multi-D Modeling Techniques for IC Engine Simulation provides a description of the most significant and recent achievements in the field of 1D engine simulation models and coupled 1D-3D modeling techniques, including 0D combustion models, quasi-3D methods and some 3D model applications.
Download or read book Combustion for Power Generation and Transportation written by Avinash Kumar Agarwal and published by Springer. This book was released on 2017-01-20 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: This research monograph presents both fundamental science and applied innovations on several key and emerging technologies involving fossil and alternate fuel utilization in power and transport sectors from renowned experts in the field. Some of the topics covered include: autoignition in laminar and turbulent nonpremixed flames; Langevin simulation of turbulent combustion; lean blowout (LBO) prediction through symbolic time series analysis; lasers and optical diagnostics for next generation IC engine development; exergy destruction study on small DI diesel engine; and gasoline direct injection. The book includes a chapter on carbon sequestration and optimization of enhanced oil and gas recovery. The contents of this book will be useful to researchers and professionals working on all aspects on combustion.
Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Science & Business Media. This book was released on 2010-03-03 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Phenomenology of Diesel Combustion and Modeling Diesel is the most efficient combustion engine today and it plays an important role in transport of goods and passengers on land and on high seas. The emissions must be controlled as stipulated by the society without sacrificing the legendary fuel economy of the diesel engines. These important drivers caused innovations in diesel engineering like re-entrant combustion chambers in the piston, lower swirl support and high pressure injection, in turn reducing the ignition delay and hence the nitric oxides. The limits on emissions are being continually reduced. The- fore, the required accuracy of the models to predict the emissions and efficiency of the engines is high. The phenomenological combustion models based on physical and chemical description of the processes in the engine are practical to describe diesel engine combustion and to carry out parametric studies. This is because the injection process, which can be relatively well predicted, has the dominant effect on mixture formation and subsequent course of combustion. The need for improving these models by incorporating new developments in engine designs is explained in Chapter 2. With “model based control programs” used in the Electronic Control Units of the engines, phenomenological models are assuming more importance now because the detailed CFD based models are too slow to be handled by the Electronic Control Units. Experimental work is necessary to develop the basic understanding of the pr- esses.
Download or read book Heat and Mass Transfer written by Hans Dieter Baehr and published by Springer Science & Business Media. This book was released on 2006-08-02 with total page 706 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a solid foundation in the principles of heat and mass transfer and shows how to solve problems by applying modern methods. The basic theory is developed systematically, exploring in detail the solution methods to all important problems. The revised second edition incorporates state-of-the-art findings on heat and mass transfer correlations. The book will be useful not only to upper- and graduate-level students, but also to practicing scientists and engineers. Many worked-out examples and numerous exercises with their solutions will facilitate learning and understanding, and an appendix includes data on key properties of important substances.
Download or read book Engineering Fundamentals of the Internal Combustion Engine written by Willard W. Pulkrabek and published by Pearson. This book was released on 2013-11-01 with total page 485 pages. Available in PDF, EPUB and Kindle. Book excerpt: This applied thermoscience text explores the basic principles and applications of various types of internal combustion engines, with a major emphasis on reciprocating engines.
Download or read book Internal Combustion Engine Fundamentals written by John B. Heywood and published by McGraw-Hill Education. This book was released on 1988 with total page 930 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text, by a leading authority in the field, presents a fundamental and factual development of the science and engineering underlying the design of combustion engines and turbines. An extensive illustration program supports the concepts and theories discussed.
Download or read book Fundamentals of Fuel Injection and Emission in Two Stroke Engines written by Wadysaw Mitianiec and published by Nova Science Publishers. This book was released on 2018 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The main goal of the book is the presentation of the last theoretical and experimental works concerning fuel injection systems, mainly in small power two-stroke engines as well as in marine engines. This book includes thirteen chapters devoted to the processes of fuel injection and the combustion that takes place in a stratified charge within the cylinders of two-stroke engines. In the first two chapters, the division into different injection systems in two-stroke engines and each injection system is briefly described. Various theoretical and practical solutions of fueling system designs are described. In Chapter Three, mathematical models, the spatial movement of gas in the cylinder and the combustion chamber are introduced, taking into account the turbulence of the charge. Chapter Four relates to the behavior of fuel injected into the gaseous medium, including evaporation processes, disintegration and processes occurring while the fuel drops connect with the wall. The next section describes the zero-dimensional model of fuel injection in two-stroke engines along with examples of numerical calculations. The sixth chapter is devoted to CFD multi-dimensional models of movement and evaporation of the fuel in a closed gaseous medium, occurring also in other engine types. Chapter Seven describes a two-zone model of the combustion process and the effect of the geometry of the combustion chamber on the flame propagation with a simplified verification model of combustion. Chapter Eight compares the propagation phase of gas and liquid fuels concerning direct fuel injection as well as the direct fuel injection from the cylinder head and the thermodynamic parameters of the charge. The formation of the components during the combustion process in the direct fuel injection two-stroke engine was obtained by numerical calculations and results are discussed in Chapter Nine. Chapter Ten describes the parameters of the two-stroke engine with a direct fuel injection carried out at the Cracow University of Technology. Additionally, the chapter presents CFD simulations of fuel propagation and combustion processes, taking into account the formation of toxic components and exhaust gas emission. The processes of two direct rich mixture injection systems FAST and RMIS developed in CUT are presented in Chapter Eleven. Miscellaneous problems of direct fuel injection, such as characteristics of fuel injectors, problems of direct gaseous fuel injection, and the application of fuelling systems in outboard engines and snowmobile vehicles are presented in Chapter Twelve. A comparison of working parameters in two- and four stroke engines is also mapped out. The last chapters contain the final conclusions and remarks concerning fuel injection and emission of exhaust gases in small two-stroke engines. This book is a comprehensive monograph on fuel injection. The author presents a series of theoretical and design information from his own experience and on the basis of the works of other authors. The main text intends to direct fuel injection with respect to gas motion in the combustion chamber and influence the injection parameters for exhaust emission. The book presents its own theoretical work and experimental tests concerning a two-stroke gasoline engine with electrically controlled direct fuel injection. The book describes the processes of a general nature also occurring in other types of engines and presents a comparison of different injection systems on working parameters and gas emission. The book contains 294 images, 290 equations and 16 tables obtained from the CFD simulation and experimental works.
Download or read book Mathematical Modelling in Science and Technology written by Xavier J.R. Avula and published by Elsevier. This book was released on 2014-05-09 with total page 1023 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mathematical Modelling in Science and Technology: The Fourth International Conference covers the proceedings of the Fourth International Conference by the same title, held at the Swiss Federal Institute of Technology, Zurich, Switzerland on August 15-17, 1983. Mathematical modeling is a powerful tool to solve many complex problems presented by scientific and technological developments. This book is organized into 20 parts encompassing 180 chapters. The first parts present the basic principles, methodology, systems theory, parameter estimation, system identification, and optimization of mathematical modeling. The succeeding parts discuss the features of stochastic and numerical modeling and simulation languages. Considerable parts deal with the application areas of mathematical modeling, such as in chemical engineering, solid and fluid mechanics, water resources, medicine, economics, transportation, and industry. The last parts tackle the application of mathematical modeling in student management and other academic cases. This book will prove useful to researchers in various science and technology fields.
Download or read book Internal Combustion Engines written by Colin R. Ferguson and published by John Wiley & Sons. This book was released on 2015-07-01 with total page 477 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the publication of the Second Edition in 2001, there have been considerable advances and developments in the field of internal combustion engines. These include the increased importance of biofuels, new internal combustion processes, more stringent emissions requirements and characterization, and more detailed engine performance modeling, instrumentation, and control. There have also been changes in the instructional methodologies used in the applied thermal sciences that require inclusion in a new edition. These methodologies suggest that an increased focus on applications, examples, problem-based learning, and computation will have a positive effect on learning of the material, both at the novice student, and practicing engineer level. This Third Edition mirrors its predecessor with additional tables, illustrations, photographs, examples, and problems/solutions. All of the software is ‘open source’, so that readers can see how the computations are performed. In addition to additional java applets, there is companion Matlab code, which has become a default computational tool in most mechanical engineering programs.
Download or read book Combustion written by J. Warnatz and published by Springer Science & Business Media. This book was released on 2006-09-23 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a rigorous treatment of the coupling of chemical reactions and fluid flow. Combustion-specific topics of chemistry and fluid mechanics are considered and tools described for the simulation of combustion processes. This edition is completely restructured. Mathematical Formulae and derivations as well as the space-consuming reaction mechanisms have been replaced from the text to appendix. A new chapter discusses the impact of combustion processes on the atmosphere, the chapter on auto-ignition is extended to combustion in Otto- and Diesel-engines, and the chapters on heterogeneous combustion and on soot formation are heavily revised.
Download or read book Combustion Engines Development written by Günter P. Merker and published by Springer Science & Business Media. This book was released on 2011-09-24 with total page 660 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion Engines Development nowadays is based on simulation, not only of the transient reaction of vehicles or of the complete driveshaft, but also of the highly unsteady processes in the carburation process and the combustion chamber of an engine. Different physical and chemical approaches are described to show the potentials and limits of the models used for simulation.
Download or read book Computer Simulation Of Spark Ignition Engine Processes written by V. Ganesan and published by Universities Press. This book was released on 1996 with total page 252 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains the theory and computer programs for the simulation of spark ignition (SI) engine processes. It starts with the fundamental concepts and goes on to the advanced level and can thus be used by undergraduates, postgraduates and Ph. D. scholars.
Download or read book Engine Modeling and Simulation written by Avinash Kumar Agarwal and published by Springer Nature. This book was released on 2021-12-16 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the simulation and modeling of internal combustion engines. The contents include various aspects of diesel and gasoline engine modeling and simulation such as spray, combustion, ignition, in-cylinder phenomena, emissions, exhaust heat recovery. It also explored engine models and analysis of cylinder bore piston stresses and temperature effects. This book includes recent literature and focuses on current modeling and simulation trends for internal combustion engines. Readers will gain knowledge about engine process simulation and modeling, helpful for the development of efficient and emission-free engines. A few chapters highlight the review of state-of-the-art models for spray, combustion, and emissions, focusing on the theory, models, and their applications from an engine point of view. This volume would be of interest to professionals, post-graduate students involved in alternative fuels, IC engines, engine modeling and simulation, and environmental research.
Download or read book Introduction to Internal Combustion Engines written by Richard Stone and published by Bloomsbury Publishing. This book was released on 2017-09-16 with total page 516 pages. Available in PDF, EPUB and Kindle. Book excerpt: Now in its fourth edition, this textbook remains the indispensable text to guide readers through automotive or mechanical engineering, both at university and beyond. Thoroughly updated, clear, comprehensive and well-illustrated, with a wealth of worked examples and problems, its combination of theory and applied practice aids in the understanding of internal combustion engines, from thermodynamics and combustion to fluid mechanics and materials science. This textbook is aimed at third year undergraduate or postgraduate students on mechanical or automotive engineering degrees. New to this Edition: - Fully updated for changes in technology in this fast-moving area - New material on direct injection spark engines, supercharging and renewable fuels - Solutions manual online for lecturers
