Download or read book Impingement Jet Cooling in Gas Turbines written by R.S. Amano and published by WIT Press. This book was released on 2014-05-28 with total page 253 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to the requirement for enhanced cooling technologies on modern gas turbine engines, advanced research and development has had to take place in field of thermal engineering. Among the gas turbine cooling technologies, impingement jet cooling is one of the most effective in terms of cooling effectiveness, manufacturability and cost. The chapters contained in this book describe research on state-of-the-art and advanced cooling technologies that have been developed, or that are being researched, with a variety of approaches from theoretical, experimental, and CFD studies. The authors of the chapters have been selected from some of the most active researchers and scientists on the subject. This is the first to book published on the topics of gas turbines and heat transfer to focus on impingement cooling alone.
Download or read book Gas Turbine Blade Cooling written by Chaitanya D Ghodke and published by SAE International. This book was released on 2018-12-10 with total page 238 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gas turbines play an extremely important role in fulfilling a variety of power needs and are mainly used for power generation and propulsion applications. The performance and efficiency of gas turbine engines are to a large extent dependent on turbine rotor inlet temperatures: typically, the hotter the better. In gas turbines, the combustion temperature and the fuel efficiency are limited by the heat transfer properties of the turbine blades. However, in pushing the limits of hot gas temperatures while preventing the melting of blade components in high-pressure turbines, the use of effective cooling technologies is critical. Increasing the turbine inlet temperature also increases heat transferred to the turbine blade, and it is possible that the operating temperature could reach far above permissible metal temperature. In such cases, insufficient cooling of turbine blades results in excessive thermal stress on the blades causing premature blade failure. This may bring hazards to the engine's safe operation. Gas Turbine Blade Cooling, edited by Dr. Chaitanya D. Ghodke, offers 10 handpicked SAE International's technical papers, which identify key aspects of turbine blade cooling and help readers understand how this process can improve the performance of turbine hardware.
Download or read book Journal of Thermophysics and Heat Transfer written by and published by . This book was released on 2006 with total page 996 pages. Available in PDF, EPUB and Kindle. Book excerpt: This journal is devoted to the advancement of the science and technology of thermophysics and heat transfer through the dissemination of original research papers disclosing new technical knowledge and exploratory developments and applications based on new knowledge. It publishes papers that deal with the properties and mechanisms involved in thermal energy transfer and storage in gases, liquids, and solids or combinations thereof. These studies include conductive, convective, and radiative modes alone or in combination and the effects of the environment.
Download or read book Heat Transfer in Gas Turbines written by Bengt Sundén and published by Witpress. This book was released on 2001 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: This title presents and reflects current active research on various heat transfer topics and related phenomena in gas turbine systems. It begins with a general introduction to gas turbine heat transfer, before moving on to specific areas.
Download or read book Three Dimensional Attached Viscous Flow written by Ernst Heinrich Hirschel and published by Springer Science & Business Media. This book was released on 2013-10-29 with total page 396 pages. Available in PDF, EPUB and Kindle. Book excerpt: Viscous flow is treated usually in the frame of boundary-layer theory and as two-dimensional flow. Books on boundary layers give at most the describing equations for three-dimensional boundary layers, and solutions often only for some special cases. This book provides basic principles and theoretical foundations regarding three-dimensional attached viscous flow. Emphasis is put on general three-dimensional attached viscous flows and not on three-dimensional boundary layers. This wider scope is necessary in view of the theoretical and practical problems to be mastered in practice. The topics are weak, strong, and global interaction, the locality principle, properties of three-dimensional viscous flow, thermal surface effects, characteristic properties, wall compatibility conditions, connections between inviscid and viscous flow, flow topology, quasi-one- and two-dimensional flows, laminar-turbulent transition and turbulence. Though the primary flight speed range is that of civil air transport vehicles, flows past other flying vehicles up to hypersonic speeds are also considered. Emphasis is put on general three-dimensional attached viscous flows and not on three-dimensional boundary layers, as this wider scope is necessary in view of the theoretical and practical problems that have to be overcome in practice. The specific topics covered include weak, strong, and global interaction; the locality principle; properties of three-dimensional viscous flows; thermal surface effects; characteristic properties; wall compatibility conditions; connections between inviscid and viscous flows; flow topology; quasi-one- and two-dimensional flows; laminar-turbulent transition; and turbulence. Detailed discussions of examples illustrate these topics and the relevant phenomena encountered in three-dimensional viscous flows. The full governing equations, reference-temperature relations for qualitative considerations and estimations of flow properties, and coordinates for fuselages and wings are also provided. Sample problems with solutions allow readers to test their understanding.
Download or read book Gas Turbine Heat Transfer and Cooling Technology Second Edition written by Je-Chin Han and published by CRC Press. This book was released on 2012-11-27 with total page 892 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.
Download or read book Cooling of Electronic Systems written by Sadik Kakaç and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 953 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electronic technology is developing rapidly and, with it, the problems associated with the cooling of microelectronic equipment are becoming increasingly complex. So much so that it is necessary for experts in the fluid and thermal sciences to become involved with the cooling problem. Such thoughts as these led to an approach to leading specialists with a request to contribute to the present book. Cooling of Electronic Systems presents the technical progress achieved in the fundamentals of the thermal management of electronic systems and thermal strategies for the design of microelectronic equipment. The book starts with an introduction to the cooling of electronic systems, involving such topics as trends in computer system cooling, the cooling of high performance computers, thermal design of microelectronic components, natural and forced convection cooling, cooling by impinging air and liquid jets, thermal control systems for high speed computers, together with a detailed review of advances in manufacturing and assembly technology. Following this, practical methods for the determination of the parameters required for the thermal analysis of electronic systems and the accurate prediction of temperature in consumer electronics. Cooling of Electronic Systems is currently the most up-to-date book on the thermal management of electronic and microelectronic equipment, and the subject is presented by eminent scientists and experts in the field. Vital reading for all designers of modern, high-speed computers.
Download or read book Handbook of Thermal Science and Engineering written by and published by Springer. This book was released on 2018-07-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook provides researchers, faculty, design engineers in industrial R&D, and practicing engineers in the field concise treatments of advanced and more-recently established topics in thermal science and engineering, with an important emphasis on micro- and nanosystems, not covered in earlier references on applied thermal science, heat transfer or relevant aspects of mechanical/chemical engineering. Major sections address new developments in heat transfer, transport phenomena, single- and multiphase flows with energy transfer, thermal-bioengineering, thermal radiation, combined mode heat transfer, coupled heat and mass transfer, and energy systems. Energy transport at the macro-scale and micro/nano-scales is also included. The internationally recognized team of authors adopt a consistent and systematic approach and writing style, including ample cross reference among topics, offering readers a user-friendly knowledgebase greater than the sum of its parts, perfect for frequent consultation. The Handbook of Thermal Science and Engineering is ideal for academic and professional readers in the traditional and emerging areas of mechanical engineering, chemical engineering, aerospace engineering, bioengineering, electronics fabrication, energy, and manufacturing concerned with the influence thermal phenomena.
Download or read book Advances in Heat Transfer written by and published by Elsevier. This book was released on 2023-05-25 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Heat Transfer, Volume 55, the newest release in this series, highlights advances in the field with this new volume presenting interesting chapters written by an international board of authors. Topics discussed in this release include Mesoscopic Scale Simulations of Heat Transport in Porous Structures, Advancements in Single-Phase Enhanced Heat Transfer in Microchannels, and more. - Provides the authority and expertise of leading contributors from an international board of authors - Presents the latest release in the Advances in Heat Transfer series
Download or read book Gas Turbine Heat Transfer and Cooling Technology written by Je-Chin Han and published by Taylor & Francis. This book was released on 2012-11-27 with total page 865 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference for engineers and researchers, this second edition focuses on gas turbine heat transfer issues and their associated cooling technologies for aircraft and land-based gas turbines. It provides information on state-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling schemes. The book also offers updated experimental methods for gas turbine heat transfer and cooling research, as well as advanced computational models for gas turbine heat transfer and cooling performance predictions. The authors provide suggestions for future research within this technology and includes 800 illustrations to help clarify concepts and instruction.
Download or read book Thermal Quadrupoles written by Denis Maillet and published by . This book was released on 2000-11-17 with total page 392 pages. Available in PDF, EPUB and Kindle. Book excerpt: This superb text describes a novel and powerful method for allowing design engineers to firstly model a linear problem in heat conduction, then build a solution in an explicit form and finally obtain a numerical solution. It constitutes a modelling and calculation tool based on a very efficient and systemic methodological approach. Solving the heat equations through integral transforms does not constitute a new subject. However, finding a solution generally constitutes only one part of the problem. In design problems, an initial thermal design has to be tested through the calculation of the temperature or flux field, followed by an analysis of this field in terms of constraints. A modified design is then proposed, followed by a new thermal field calculation, and so on until the right design is found. The thermal quadrupole method allows this often painful iterative procedure to be removed by allowing only one calculation. The chapters in this book increase in complexity from a rapid presentation of the method for one dimensional transient problems in chapter one, to non uniform boundary conditions or inhomogeneous media in chapter six. In addition, a wide range of corrected problems of contemporary interest are presented mainly in chapters three and six with their numerical implementation in MATLAB (r) language. This book covers the whole scope of linear problems and presents a wide range of concrete issues of contemporary interest such as harmonic excitations of buildings, transfer in composite media, thermal contact resistance and moving material heat transfer. Extensions of this method to coupled transfers in a semi-transparent medium and to mass transfer in porous media are considered respectively in chapters seven and eight. Chapter nine is devoted to practical numerical methods that can be used to inverse the Laplace transform. Written from an engineering perspective, with applications to real engineering problems, this book will be of significant interest not only to researchers, lecturers and graduate students in mechanical engineering (thermodynamics) and process engineers needing to model a heat transfer problem to obtain optimized operating conditions, but also to researchers interested in the simulation or design of experiments where heat transfer play a significant role.
Download or read book Heat Transfer in Gas Turbine Systems written by Richard J. Goldstein and published by . This book was released on 2001 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Explores recent developments in heat transfer and thermal control applied to modern high-temperature gas turbine systems. It examines experimental results and techniques computational studies and methods and design recommendations. Aspects of heat transfer in rotating machinery are studied as well as thermal aspects of other sections of the turbine (e.g. the compressor). Proceedings of an August 2000 conference.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1986 with total page 992 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Journal of Heat Transfer written by and published by . This book was released on 2008 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book NASA SP written by and published by . This book was released on 1993 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Rules of Thumb for Mechanical Engineers written by J. Edward Pope and published by Gulf Professional Publishing. This book was released on 1997 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fluids -- Heat transfer -- Thermodynamics -- Mechanical seals -- Pumps and compressors -- Drivers -- Gears -- Bearings -- Piping and pressure vessels -- Tribology -- Vibration -- Materials -- Stress and strain -- Fatigue -- Instrumentation -- Engineering economics.
Download or read book Proceedings of the ASME Turbo Expo 2002 written by and published by . This book was released on 2002 with total page 590 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Volumes 3A and 3B are part of a five-volume set comprising the proceedings of the June 2002 conference held in the Netherlands. Approximately 125 articles address heat transfer, and manufacturing materials and metallurgy. A sampling of topics: the effect of freestream turbulence on film cooling adiabatic effectiveness; the influence of periodic unsteady inflow conditions on leading edge film cooling; and fluid dynamcis of a pre-swirl rotor-stator system. No subject index. Annotation c. Book News, Inc., Portland, OR (booknews.com).
