Download or read book IUTAM Symposium on Designing for Quietness written by MANOHAR LAL Munjal and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 329 pages. Available in PDF, EPUB and Kindle. Book excerpt: It is well known that noise control at the source is the most cost-effective. Designing for quietness is therefore the most important concept in Engineering Acoustics or Technical Acoustics. The IUTAM Symposium on Designing for Quietness held at the Indian Institute of Science Bangalore in December 2000, was probably the first on this topic anywhere in the world. Papers were invited from reputed researchers and professionals spread over several countries. 18 of the 21 papers presented in the Symposium are included in these proceedings after rigorous review, revision and editing. This volume covers a large number of applications, such as silencers, lined ducts, acoustic materials, source characterization, acoustical design of vehicle cabs, ships, space antennas, MEMS pressure transducer etc., active control of structure-borne noise and cavities, SEA for engine noise and structural acoustic modelling with application to design of quieter panels. A list of references at the end of every paper will provide sources for further reading.
Download or read book IUTAM Symposium on Topological Design Optimization of Structures Machines and Materials written by Martin Philip Bendsoe and published by Springer Science & Business Media. This book was released on 2006-10-03 with total page 602 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume offers edited papers presented at the IUTAM-Symposium Topological design optimization of structures, machines and materials - status and perspectives, October 2005. The papers cover the application of topological design optimization to fluid-solid interaction problems, acoustics problems, and to problems in biomechanics, as well as to other multiphysics problems. Also in focus are new basic modelling paradigms, covering new geometry modelling such as level-set methods and topological derivatives.
Download or read book Soil Stress Strain Behavior Measurement Modeling and Analysis written by Hoe I. Ling and published by Springer Science & Business Media. This book was released on 2007-11-28 with total page 989 pages. Available in PDF, EPUB and Kindle. Book excerpt: The material in this work is focused on recent developments in research into the stress-strain behavior of geomaterials, with an emphasis on laboratory measurements, soil constitutive modeling and behavior of soil structures (such as reinforced soils, piles and slopes). The latest advancements in the field, such as the rate effect and dynamic behavior of both clay and sand, behavior of modified soils and soil mixtures, and soil liquefaction are addressed.
Download or read book Mechanics of Microelectronics written by G.Q. Zhang and published by Springer Science & Business Media. This book was released on 2006-08-25 with total page 580 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is written by leading experts with both profound knowledge and rich practical experience in advanced mechanics and the microelectronics industry essential for current and future development. It aims to provide the cutting edge knowledge and solutions for various mechanical related problems, in a systematic way. It contains important and detailed information about the state-of-the-art theories, methodologies, the way of working and real case studies.
Download or read book Elasticity of Transversely Isotropic Materials written by Haojiang Ding and published by Springer Science & Business Media. This book was released on 2006-07-09 with total page 443 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book aims to provide a comprehensive introduction to the theory and applications of the mechanics of transversely isotropic elastic materials. There are many reasons why it should be written. First, the theory of transversely isotropic elastic materials is an important branch of applied mathematics and engineering science; but because of the difficulties caused by anisotropy, the mathematical treatments and descriptions of individual problems have been scattered throughout the technical literature. This often hinders further development and applications. Hence, a text that can present the theory and solution methodology uniformly is necessary. Secondly, with the rapid development of modern technologies, the theory of transversely isotropic elasticity has become increasingly important. In addition to the fields with which the theory has traditionally been associated, such as civil engineering and materials engineering, many emerging technologies have demanded the development of transversely isotropic elasticity. Some immediate examples are thin film technology, piezoelectric technology, functionally gradient materials technology and those involving transversely isotropic and layered microstructures, such as multi-layer systems and tribology mechanics of magnetic recording devices. Thus a unified mathematical treatment and presentation of solution methods for a wide range of mechanics models are of primary importance to both technological and economic progress.
Download or read book Fracture Mechanics written by E.E. Gdoutos and published by Springer Science & Business Media. This book was released on 2005-07-25 with total page 391 pages. Available in PDF, EPUB and Kindle. Book excerpt: New developments in the applications of fracture mechanics to engineering problems have taken place in the last years. Composite materials have extensively been used in engineering problems. Quasi-brittle materials including concrete, cement pastes, rock, soil, etc. all benefit from these developments. Layered materials and especially thin film/substrate systems are becoming important in small volume systems used in micro and nanoelectromechancial systems (MEMS and NEMS). Nanostructured materials are being introduced in our every day life. In all these problems fracture mechanics plays a major role for the prediction of failure and safe design of materials and structures. These new challenges motivated the author to proceed with the second edition of the book. The second edition of the book contains four new chapters in addition to the ten chapters of the first edition. The fourteen chapters of the book cover the basic principles and traditional applications, as well as the latest developments of fracture mechanics as applied to problems of composite materials, thin films, nanoindentation and cementitious materials. Thus the book provides an introductory coverage of the traditional and contemporary applications of fracture mechanics in problems of utmost technological importance. With the addition of the four new chapters the book presents a comprehensive treatment of fracture mechanics. It includes the basic principles and traditional applications as well as the new frontiers of research of fracture mechanics during the last three decades in topics of contemporary importance, like composites, thin films, nanoindentation and cementitious materials. The book contains fifty example problems and more than two hundred unsolved problems. A "Solutions Manual" is available upon request for course instructors from the author.
Download or read book Self Consistent Methods for Composites written by S.K. Kanaun and published by Springer Science & Business Media. This book was released on 2007-12-20 with total page 390 pages. Available in PDF, EPUB and Kindle. Book excerpt: This timely text is the first monograph to develop self-consistent methods and apply these to the solution of problems of electromagnetic and elastic wave propagation in matrix composites and polycrystals. Predictions are compared with experimental data and exact solutions. Explicit equations and efficient numerical algorithms for calculating the velocities and attenuation coefficients of the mean (coherent) wave fields propagating in composites and polycrystals are presented.
Download or read book Optimal Control from Theory to Computer Programs written by Viorel Arnăutu and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: The aim of this book is to present the mathematical theory and the know-how to make computer programs for the numerical approximation of Optimal Control of PDE's. The computer programs are presented in a straightforward generic language. As a consequence they are well structured, clearly explained and can be translated easily into any high level programming language. Applications and corresponding numerical tests are also given and discussed. To our knowledge, this is the first book to put together mathematics and computer programs for Optimal Control in order to bridge the gap between mathematical abstract algorithms and concrete numerical ones. The text is addressed to students and graduates in Mathematics, Mechanics, Applied Mathematics, Numerical Software, Information Technology and Engineering. It can also be used for Master and Ph.D. programs.
Download or read book A Modern Course in Aeroelasticity written by Robert Clark and published by Springer Science & Business Media. This book was released on 2006-01-24 with total page 770 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this new edition, the fundamental material on classical linear aeroelasticity has been revised. Also new material has been added describing recent results on the research frontiers dealing with nonlinear aeroelasticity as well as major advances in the modelling of unsteady aerodynamic flows using the methods of computational fluid dynamics and reduced order modeling techniques. New chapters on aeroelasticity in turbomachinery and aeroelasticity and the latter chapters for a more advanced course, a graduate seminar or as a reference source for an entrée to the research literature.
Download or read book Plate and Panel Structures of Isotropic Composite and Piezoelectric Materials Including Sandwich Construction written by Jack R. Vinson and published by Springer Science & Business Media. This book was released on 2005-02-08 with total page 448 pages. Available in PDF, EPUB and Kindle. Book excerpt: Plates and panels are primary components in many structures including space vehicles, aircraft, automobiles, buildings, bridge decks, ships and submarines. The ability to design, analyse, optimise and select the proper materials for these structures is a necessity for structural designers, analysts and researchers. This text consists of four parts. The first deals with plates of isotropic (metallic and polymeric) materials. The second involves composite material plates, including anisotropy and laminate considerations. The third section treats sandwich constructions of various types, and the final section gives an introduction to plates involving piezoelectric materials, in which the "smart" or "intelligent" materials are used as actuators or sensors. In each section, the formulations encompass plate structures subjected to static loads, dynamic loads, buckling, thermal/moisture environments, and minimum weight structural optimisation. This is a textbook for a graduate course, an undergraduate senior course and a reference. Many homework problems are given in various chapters.
Download or read book Parallel Robots written by J.P. Merlet and published by Springer Science & Business Media. This book was released on 2006-07-01 with total page 418 pages. Available in PDF, EPUB and Kindle. Book excerpt: Parallel robots are closed-loop mechanisms presenting very good performances in terms of accuracy, velocity, rigidity and ability to manipulate large loads. They have been used in a large number of applications ranging from astronomy to flight simulators and are becoming increasingly popular in the field of machine-tool industry. This book presents a complete synthesis of the latest results on the possible mechanical architectures, analysis and synthesis of this type of mechanism. It is intended to be used by students (with over 150 exercises and numerous internet addresses), researchers (with over 650 references and anonymous ftp access to the code of some algorithms presented in this book) and engineers (for which practical results, mistakes to avoid, and applications are presented). Since the publication of the first edition (2000) there has been an impressive increase in terms of study and use of this kind of structure that are reported in this book. This second edition has been completely overhauled. The initial chapter on kinematics has been split into Inverse Kinematics and Direct Kinematics. A new chapter on calibration was added. The other chapters have also been rewritten to a large extent. The reference section has been updated to include around 45% new works that appeared after the first edition.
Download or read book Models of Mechanics written by A. Klarbring and published by Springer Science & Business Media. This book was released on 2006-09-05 with total page 214 pages. Available in PDF, EPUB and Kindle. Book excerpt: This textbook on models and modeling in mechanics introduces a new unifying approach to applied mechanics: through the concept of the open scheme, a step-by-step approach to modeling evolves. The unifying approach enables a very large scope on relatively few pages: the book treats theories of mass points and rigid bodies, continuum models of solids and fluids, as well as traditional engineering mechanics of beams, cables, pipe flow and wave propagation.
Download or read book Fundamentals of Cavitation written by Jean-Pierre Franc and published by Springer Science & Business Media. This book was released on 2006-01-22 with total page 321 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book treats cavitation, which is a unique phenomenon in the field of hyd- dynamics, although it can occur in any hydraulic machinery such as pumps, propellers, artificial hearts, and so forth. Cavitation is generated not only in water, but also in any kind of fluid, such as liquid hydrogen. The generation of cavitation can cause severe damage in hydraulic machinery. Therefore, the prevention of cavitation is an important concern for designers of hydraulic machinery. On the contrary, there is great potential to utilize cavitation in various important applications, such as environmental protection. There have been several books published on cavitation, including one by the same authors. This book differs from those previous ones, in that it is both more physical and more theoretical. Any theoretical explanation of the cavitation phenomenon is rather difficult, but the authors have succeeded in explaining it very well, and a reader can follow the equations easily. It is an advantage in reading this book to have some understanding of the physics of cavitation. Therefore, this book is not an introductory text, but a book for more advanced study. However, this does not mean that this book is too difficult for a beginner, because it explains the cavitation phenomenon using many figures. Therefore, even a beginner on cavitation can read and can understand what cavitation is. If the student studies through this book (with patience), he or she can become an expert on the physics of cavitation.
Download or read book Dynamics of Advanced Materials and Smart Structures written by Kazumi Watanabe and published by Springer Science & Business Media. This book was released on 2013-04-17 with total page 501 pages. Available in PDF, EPUB and Kindle. Book excerpt: Two key words for mechanical engineering in the future are Micro and Intelligence. It is weIl known that the leadership in the intelligence technology is a marter of vital importance for the future status of industrial society, and thus national research projects for intelligent materials, structures and machines have started not only in advanced countries, but also in developing countries. Materials and structures which have self-sensing, diagnosis and actuating systems, are called intelligent or smart, and are of growing research interest in the world. In this situation, the IUT AM symposium on Dynamics 0/ Advanced Materials and Smart Structures was a timely one. Smart materials and structures are those equipped with sensors and actuators to achieve their designed performance in achanging environment. They have complex structural properties and mechanical responses. Many engineering problems, such as interface and edge phenomena, mechanical and electro-magnetic interaction/coupling and sensing, actuating and control techniques, arise in the development ofintelligent structures. Due to the multi-disciplinary nature ofthese problems, all ofthe classical sciences and technologies, such as applied mathematics, material science, solid and fluid mechanics, control techniques and others must be assembled and used to solve them. IUTAM weIl understands the importance ofthis emerging technology. An IUTAM symposium on Smart Structures and Structronic Systems (Chaired by U.
Download or read book Variational and Quasi Variational Inequalities in Mechanics written by Alexander S. Kravchuk and published by Springer Science & Business Media. This book was released on 2007-09-04 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: The essential aim of this book is to consider a wide set of problems arising in the mathematical modeling of mechanical systems under unilateral constraints. In these investigations elastic and non-elastic deformations, friction and adhesion phenomena are taken into account. All the necessary mathematical tools are given: local boundary value problem formulations, construction of variational equations and inequalities and their transition to minimization problems, existence and uniqueness theorems, and variational transformations (Friedrichs and Young-Fenchel-Moreau) to dual and saddle-point search problems.
Download or read book Applied High Speed Plate Penetration Dynamics written by Gabi Ben-Dor and published by Springer Science & Business Media. This book was released on 2006-02-22 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: High-speed impact dynamics is of interest in the fundamental sciences, e.g., astrophysics and space sciences, and has a number of important applications in military technologies, homeland security and engineering. When compared with experiments or numerical simulations, analytical approaches in impact mechanics only seldom yield useful results. However, when successful, analytical approaches allow us to determine general laws that are not only important in themselves but also serve as benchmarks for subsequent numerical simulations and experiments. The main goal of this monograph is to demonstrate the potential and effectiveness of analytical methods in applied high-speed penetration mechanics for two classes of problem. The first class of problem is shape optimization of impactors penetrating into ductile, concrete and some composite media. The second class of problem comprises investigation of ballistic properties and optimization of multi-layered shields, including spaced and two-component ceramic shields. Despite the massive use of mathematical techniques, the obtained results have a clear engineering meaning and are presented in an easy-to-use form. One of the chapters is devoted solely to some common approximate models, and this is the first time that a comprehensive description of the localized impactor/medium interaction approach is given. In the monograph the authors present systematically their theoretical results in the field of high-speed impact dynamics obtained during the last decade which only partially appeared in scientific journals and conferences proceedings.
Download or read book Thermoelastic Models of Continua written by D. Iesan and published by Springer Science & Business Media. This book was released on 2013-03-19 with total page 309 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume is concerned with the basic problems of the theory of thermoelasticity for three models of continuous bodies: materials with voids, micropolar solids and nonsimple bodies. Beginning with the basic laws of thermodynamics, the theory of thermoelastic materials with voids is treated. Two subsequent chapters cover the analysis of the linear theory of micropolar thermoelastic bodies. The book concludes with a study of nonsimple thermoelastic materials, which are characterised by the inclusion of higher gradients of displacement in the basic postulates. Relevant examples and exercises which illustrate the theory are given throughout the text. The book should be of interest to mathematicians and specialists working in the fields of elasticity, thermoelasticity, civil engineering and geophysics.
