EBookClubs

Read Books & Download eBooks Full Online

EBookClubs

Read Books & Download eBooks Full Online

Book Fabrication of Zinc Nitride Thin Films Using RF Magnetron Sputtering Deposition for Optoelectronic Applications

Download or read book Fabrication of Zinc Nitride Thin Films Using RF Magnetron Sputtering Deposition for Optoelectronic Applications written by Ting Wen and published by . This book was released on 2012 with total page 122 pages. Available in PDF, EPUB and Kindle. Book excerpt: Zinc nitride thin films possess a small optical band gap with direct transition, low resistivity, high mobility and carrier concentration. Therefore, it may be suitable as an optoelectronic material for infrared sensors, smart windows and energy conversion devices. The objective of this work is to grow zinc nitride thin films using RF magnetron sputtering, understand its mechanical, optical, and electrical properties, and investigate its performance as light sensing devices. Synthesis and characterization of zinc nitride thin films has been investigated in this work. An RF magnetron sputtering deposition was employed to synthesize zinc nitride thin films using pure metal zinc target in either N2-Ar or N2-Ar-H2 mixtures. The microstructural, optical and electrical characterizations of the representative films were investigated with stylus profilometry, XRD, AFM, SEM, TEM, UV-VIS-NIR double beam spectrometry, and Hall effect measurement. The photoresponse of the zinc nitride photoconductors was also studied under the irradiation of white light and NIR light. The as-deposited zinc nitride thin films were relatively soft and densely packed with smooth surface. It possesses a narrow optical band gap in the NIR range with direct transition. The zinc nitride showed n-type conductivity with low resistivity and high carrier concentration. To study the RF discharge power effect, the zinc nitride thin films were synthesized at different discharge powers densities. With discharge power density increasing, the film deposition rate increased, and the zinc nitride films acquired better crystalline structure, smaller optical band gap and less oxygen contaminations. After thermal annealing at moderate temperatures in either air or O2, the annealed zinc nitride thin films were photoconductive under irradiation of both NIR light and white light. The largest photoresponse and fastest response times were measured at the room temperature for the zinc nitride thin films annealed at 300 degree in the air. Hydrogen inclusion can modify the electrical and optical properties of crystalline semiconductor films by introducing impurity donor states. The ZnNx:H films deposited in N2-Ar-H2 mixture acquired less oxygen contamination and higher relative nitrogen atom concentration than the ZnNx films deposited in N2-Ar mixture. The as-deposited ZnNx:H films showed a clear photonic behavior under white light irradiation, and the annealed ZnNx:H films exhibited a pronounced change in resistance under both white light and NIR light irradiation comparing to the annealed ZnNx films. This was the first time to report photoresponse of zinc nitride thin films fabricated by reactive sputtering method. The photoconductivity was gradually improved by optimization of deposition conditions, annealing conditions and film compositions.

Book Tin Oxide Indium Tin Oxide Thin Films for Photovotaic Application

Download or read book Tin Oxide Indium Tin Oxide Thin Films for Photovotaic Application written by Anshuman Borthakur and published by LAP Lambert Academic Publishing. This book was released on 2014-04 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt: With dwindling energy reserves, Photovoltaic(PV) module which is one of the most promising renewable sources of energy is slowly becoming indispensable for world's electricity production paradigm. Due to the low electrical resistance and high optical transparency in the visible range of the electromagnetic spectrum, Transparent Conducting Oxide (TCO) thin film(TF)s have found application as window electrode for fabrication of solar cell. Besides TCOs have wide application in display devices and other optoelectronic devices. This book mainly focuses on the fabrication and study of the optoelectronic properties of TCO thin films with special reference to PV application. This book also includes the fabrication and study of a heterojunction II-VI semiconductor solar cell using TCO as front electrode. It also highlights different methods used for the study of optoelectrical and structural properties of TF (e.g. SEM, XRD, thickness measurement, optical band gap, mobility, determination of carrier type, carrier concentration, conductivity etc.). This book is designed to serve as a handbook for the beginners who want to work in the field of thin film technology.

Book Zinc Oxide Bulk Thin Films and Nanostructures Processing Properties and Applications

Download or read book Zinc Oxide Bulk Thin Films and Nanostructures Processing Properties and Applications written by Chennupati Jagadish and published by Elsevier Science. This book was released on 2006-09 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt: With an in-depth exploration of the following topics, this book covers the broad uses of zinc oxide within the fields of materials science and engineering: - Recent advances in bulk, thin film and nanowire growth of ZnO (including MBE, MOCVD and PLD), - The characterization of the resulting material (including the related ternary systems ZgMgO and ZnCdO), - Improvements in device processing modules (including ion implantation for doping and isolation, Ohmic and Schottky contacts, wet and dry etching), - The role of impurities and defects on materials properties - Applications of ZnO in UV light emitters/detectors, gas, biological and chemical-sensing, transparent electronics, spintronics and thin film

Book Investigation of Magnesium Indium Oxide Thin Film Fabricated by RF Sputtering System and Their Optoelectronics Applications

Download or read book Investigation of Magnesium Indium Oxide Thin Film Fabricated by RF Sputtering System and Their Optoelectronics Applications written by 陳維德 and published by . This book was released on 2020 with total page 120 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Zinc Oxide Bulk Thin Films and Nanostructures

Download or read book Zinc Oxide Bulk Thin Films and Nanostructures written by Chennupati Jagadish and published by Elsevier. This book was released on 2011-10-10 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt: With an in-depth exploration of the following topics, this book covers the broad uses of zinc oxide within the fields of materials science and engineering:- Recent advances in bulk , thin film and nanowire growth of ZnO (including MBE, MOCVD and PLD), - The characterization of the resulting material (including the related ternary systems ZgMgO and ZnCdO), - Improvements in device processing modules (including ion implantation for doping and isolation ,Ohmic and Schottky contacts , wet and dry etching), - The role of impurities and defects on materials properties - Applications of ZnO in UV light emitters/detectors, gas, biological and chemical-sensing, transparent electronics, spintronics and thin film

Book Zinc Oxide A Material for Micro and Optoelectronic Applications

Download or read book Zinc Oxide A Material for Micro and Optoelectronic Applications written by Norbert H. Nickel and published by Springer Science & Business Media. This book was released on 2005-12-28 with total page 245 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recently, a significant effort has been devoted to the investigation of ZnO as a suitable semiconductor for UV light-emitting diodes, lasers, and detectors and hetero-substrates for GaN. Research is driven not only by the technological requirements of state-of-the-art applications but also by the lack of a fundamental understanding of growth processes, the role of intrinsic defects and dopants, and the properties of hydrogen. The NATO Advanced Research Workshop on “Zinc oxide as a material for micro- and optoelectronic applications”, held from June 23 to June 25 2004 in St. Petersburg, Russia, was organized accordingly and started with the growth of ZnO. A variety of growth methods for bulk and layer growth were discussed. These techniques comprised growth methods such as closed space vapor transport (CSVT), metal-organic chemical vapor deposition, reactive ion sputtering, and pulsed laser deposition. From a structural point of view using these growth techniques ZnO can be fabricated ranging from single crystalline bulk material to polycrystalline ZnO and nanowhiskers. A major aspect of the ZnO growth is doping. n-type doping is relatively easy to accomplish with elements such al Al or Ga. At room temperature single crystal ZnO exhibits a resistivity of about 0. 3 -cm, an electron mobility of 2 17 -3 225 cm /Vs, and a carrier concentration of 10 cm . In n-type ZnO two shallow donors are observable with activation energies of 30 – 40 meV and 60 – 70 meV.

Book Thinfilm Schottky Barriers and Heterojunctions

Download or read book Thinfilm Schottky Barriers and Heterojunctions written by Sumbit Chaliha and published by LAP Lambert Academic Publishing. This book was released on 2012-03 with total page 276 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor thin films and their junctions such as metal-semiconductor (Schottky barrier) and heterojunctions have received much attention due to their applications in various electronic and optoelectronic devices including solar cells. This book is based on the electrical and optical studies of thin film Schottky barriers and heterojunctions with an aim to use in optoelectronic devices. In this work, two wide band gap semiconductors, one Zinc Selenide (ZnSe) from group II-VI, and another transparent conducting oxide, Indium Tin Oxide are investigated in the forms of thin films and their junctions, for the possible uses as photovoltaic converter. The structural, morphological, optical and electrical (in dark and under illumination) properties of ZnSe and ITO thin films prepared at different growth conditions by thermal evaporation method have been studied by applying different experimental techniques. Schottky barriers and heterojunctions of ZnSe with different barrier metals and semiconductors have been fabricated and their current-voltage and photovoltaic characteristics are studied. The findings of it presented in this book will be helpful for the researchers of this field.

Book Optimisation of ZnO Thin Films

Download or read book Optimisation of ZnO Thin Films written by Saurabh Nagar and published by Springer. This book was released on 2017-05-22 with total page 101 pages. Available in PDF, EPUB and Kindle. Book excerpt: This monograph describes the different implantation mechanisms which can be used to achieve strong, reliable and stable p-type ZnO thin films. The results will prove useful in the field of optoelectronics in the UV region. This book will prove useful to research scholars and professionals working on doping and implantation of ZnO thin films and subsequently fabricating optoelectronic devices. The first chapter of the monograph emphasises the importance of ZnO in the field of optoelectronics for ultraviolet (UV) region and also discusses the material, electronic and optical properties of ZnO. The book then goes on to discuss the optimization of pulsed laser deposited (PLD) ZnO thin films in order to make successful p-type films. This can enable achievement of high optical output required for high-efficiency devices. The book also discusses a hydrogen implantation study on the optimized films to confirm whether the implantation leads to improvement in the optimized results.

Book Investigation of Oxide Semiconductor Based Thin Films

Download or read book Investigation of Oxide Semiconductor Based Thin Films written by Meena Suhanya Rajachidambaram and published by . This book was released on 2012 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanostructured ZnO films were obtained via thermal oxidation of thin films formed with metallic Zn-nanoparticle dispersions. Commercial zinc nanoparticles used for this work were characterized by microscopic and thermal analysis methods to analyze the Zn-ZnO core shell structure, surface morphology and oxidation characteristics. These dispersions were spin-coated on SiO2/Si substrates and then annealed in air between 100 and 600 °C. Significant nanostructural changes were observed for the resulting films, particularly those from larger Zn nanoparticles. These nanostructures, including nanoneedles and nanorods, were likely formed due to fracturing of ZnO outer shell due to differential thermal expansion between the Zn core and the ZnO shell. At temperatures above 227 °C, the metallic Zn has a high vapor pressure leading to high mass transport through these defects. Ultimately the Zn vapor rapidly oxidizes in air to form the ZnO nanostructures. We have found that the resulting films annealed above 400 °C had high electrical resistivity. The zinc nanoparticles were incorporated into zinc indium oxide solution and spin-coated to form thin film transistor (TFT) test structures to evaluate the potential of forming nanostructured field effect sensors using simple solution processing. The functionalization of zinc tin oxide (ZTO) films with self-assembled monolayers (SAMs) of n-hexylphosphonic acid (n-HPA) was investigated. The n-HPA modified ZTO surfaces were characterized using contact angle measurement, x-ray photoelectron spectroscopy (XPS) and electrical measurements. High contact angles were obtained suggesting high surface coverage of n-HPA on the ZTO films, which was also confirmed using XPS. The impact of n-HPA functionalization on the stability of ZTO TFTs was investigated. The n-HPA functionalized ZTO TFTs were either measured directly after drying or after post-annealing at 140 °C for 48 hours in flowing nitrogen. Their electrical characteristics were compared with that of non-functionalized ZTO reference TFTs fabricated using identical conditions. We found that the non-functionalized devices had a significant turn-on voltage (V[subscript ON]) shift of ~0.9 V and ~1.5 V for the non-annealed and the post-annealed conditions under positive gate bias stress for 10,000 seconds. The n-HPA modified devices showed very minimal shift in V[subscript ON] (0.1 V), regardless of post-thermal treatment. The VON instabilities were attributed to the interaction of species from the ambient atmosphere with the exposed ZTO back channel during gate voltage stress. These species can either accept or donate electrons resulting in changes in the channel conductance with respect to the applied stress.

Book Reactive Sputtering Deposition and Characterization of Zinc Nitride and Oxy nitride Films for Electronic and Photovoltaic Applications

Download or read book Reactive Sputtering Deposition and Characterization of Zinc Nitride and Oxy nitride Films for Electronic and Photovoltaic Applications written by Nanke Jiang and published by . This book was released on 2013 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation presents a study on the fabrication of zinc nitride and zinc oxy-nitride films, and related hetero-structures on glass, silicon and other substrates. The goals of this study include gaining fundamental understanding on the electrical and optical properties, the chemical-bonding states and the micro-structure of these materials and examining their potential for photovoltaic and other electronic and optoelectronic applications. Reactive radio-frequency (RF) magnetron sputtering was used as the deposition method, which potentially enables control of composition of the thin films, as well as fabrication of multilayer structures for the study of possible hetero-junctions between zinc nitride and zinc oxy-nitrides. Along with reactive sputtering, several other fabrication methods, such as thermal evaporation and solution (e.g. silver or carbon paste) painting, were used as auxiliaries where necessary. The characterization techniques employed include (i) x-ray based techniques (x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), energy dispersive x-ray spectroscopy (EDXS)), (ii) optical based methods (spectroscopic ellipsometry (SE), optical spectrophotometry, Raman spectroscopy), (iii) scanning electron microscopy (SEM), and (iv) electrical measurements (resistivity, Hall effect measurements, current-voltage and photovoltaic measurements). The cross-correlation between the deposition/post-deposition conditions and the physical properties of the films was investigated. The deposition conditions, such as the nitrogen (or oxygen) partial concentration in the sputtering gas mixture, substrate temperatures, total deposition pressure, as well as the post-deposition treatments such as thermal treatment and/or oxidation in ambient, were studied in detail. Zinc nitride, with a small fraction of "naturally" incorporated oxygen, is found to be a promising candidate for photovoltaic applications because of its optical and electrical properties. Also, the capability of property tuning for the zinc oxy-nitride material system was demonstrated by intentionally introducing varied amount oxygen into zinc nitride. In order to better understand the crystalline structure and the electronic band structure of these materials, first principle density functional theory (DFT) was used for computations of pure zinc nitride and the doping effects in it with both native elements (Zn, N) and copper family elements (Cu, Ag, Au) as possible p-type dopants. Atomic geometry, formation energy, as well as electronic structure of defects in zinc nitride were studied and a general consistency was observed between theoretically calculated and experimentally determined results. Defect density of states (DOS) suggest that among all three studied copper-family elements, copper is a good candidate for a p-type dopant. Technological insight and approaches to the fabrication of device-relevant structures were the other important outcomes of this work. Our studies showed that the fabrication of device-relevant ohmic contacts, rectifying metal-nitride junctions and p-n junctions was possible. Substantial photovoltaic action was observed in a single junction solar cell configuration that uses p-type zinc oxy-nitride as an absorber layer.

Book Solution Processed Metal Oxide Thin Films for Electronic Applications

Download or read book Solution Processed Metal Oxide Thin Films for Electronic Applications written by Zheng Cui and published by Elsevier. This book was released on 2020-06-11 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: Solution Processed Metal Oxide Thin Films for Electronic Applications discusses the fundamentals of solution processing materials chemistry techniques as they are applied to metal oxide materials systems for key device applications. The book introduces basic information (materials properties, materials synthesis, barriers), discusses ink formulation and solution processing methods, including sol-gel processing, surface functionalization aspects, and presents a comprehensive accounting on the electronic applications of solution processed metal oxide films, including thin film transistors, photovoltaic cells and other electronics devices and circuits. This is an important reference for those interested in oxide electronics, printed electronics, flexible electronics and large-area electronics. - Provides in-depth information on solution processing fundamentals, techniques, considerations and barriers combined with key device applications - Reviews important device applications, including transistors, light-emitting diodes, and photovoltaic cells - Includes an overview of metal oxide materials systems (semiconductors, nanomaterials and thin films), addressing materials synthesis, properties, limitations and surface aspects