Download or read book IN SITU MONITORING OF CORROSION DURING A LABORATORY SIMULATION OF OXALIC ACID CHEMICAL CLEANING written by and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The Savannah River Site (SRS) will disperse or dissolve precipitated metal oxides as part of radioactive waste tank closure operations. Previously SRS used oxalic acid to accomplish this task. To better understand the conditions of oxalic acid cleaning of the carbon steel waste tanks, laboratory simulations of the process were conducted to determine the corrosion rate of carbon steel and the generation of gases such as hydrogen and carbon dioxide. Open circuit potential measurements, linear polarization measurements, and coupon immersion tests were performed in-situ to determine the corrosion behavior of carbon steel during the demonstration. Vapor samples were analyzed continuously to determine the constituents of the phase. The combined results from these measurements indicated that in aerated environments, such as the tank, that the corrosion rates are manageable for short contact times and will facilitate prediction and control of the hydrogen generation rate during operations.
Download or read book Standard Methods for the Examination of Water and Wastewater written by American Public Health Association and published by . This book was released on 1981 with total page 1254 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book PWR steam generator chemical cleaning written by United States. Department of Energy. Division of Nuclear Power Development and published by . This book was released on 1978 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion Tests and Standards written by Robert Baboian and published by ASTM International. This book was released on 2005 with total page 887 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion Problems and Solutions in Oil Refining and Petrochemical Industry written by Alec Groysman and published by Springer. This book was released on 2016-10-24 with total page 369 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses corrosion problems and their solutions at facilities in the oil refining and petrochemical industry, including cooling water and boiler feed water units. Further, it describes and analyzes corrosion control actions, corrosion monitoring, and corrosion management. Corrosion problems are a perennial issue in the oil refining and petrochemical industry, as they lead to a deterioration of the functional properties of metallic equipment and harm the environment – both of which need to be protected for the sake of current and future generations. Accordingly, this book examines and analyzes typical and atypical corrosion failure cases and their prevention at refineries and petrochemical facilities, including problems with: pipelines, tanks, furnaces, distillation columns, absorbers, heat exchangers, and pumps. In addition, it describes naphthenic acid corrosion, stress corrosion cracking, hydrogen damages, sulfidic corrosion, microbiologically induced corrosion, erosion-corrosion, and corrosion fatigue occurring at refinery units. At last, fouling, corrosion and cleaning are discussed in this book.
Download or read book Stone Conservation written by Clifford A. Price and published by Getty Publications. This book was released on 2011-02-15 with total page 175 pages. Available in PDF, EPUB and Kindle. Book excerpt: First published in 1996, this volume has been substantially updated to reflect new research in the conservation of stone monuments, sculpture, and archaeological sites.
Download or read book Strategy and Methodology for Radioactive Waste Characterization written by International Atomic Energy Agency and published by IAEA. This book was released on 2007 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past decade significant progress has been achieved in the development of waste characterization and control procedures and equipment as a direct response to ever-increasing requirements for quality and reliability of information on waste characteristics. Failure in control procedures at any step can have important, adverse consequences and may result in producing waste packages which are not compliant with the waste acceptance criteria for disposal, thereby adversely impacting the repository. The information and guidance included in this publication corresponds to recent achievements and reflects the optimum approaches, thereby reducing the potential for error and enhancing the quality of the end product. -- Publisher's description.
Download or read book Methods of Seawater Analysis written by Klaus Grasshoff and published by John Wiley & Sons. This book was released on 2009-07-30 with total page 632 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the book first appeared in 1976, Methods of Seawater Analysis has found widespread acceptance as a reliable and detailed source of information. Its second extended and revised edition published in 1983 reflected the rapid pace of instrumental and methodological evolution in the preceding years. The development has lost nothing of its momentum, and many methods and procedures still suffering their teething troubles then have now matured into dependable tools for the analyst. This is especially evident for trace and ultra-trace analyses of organic and inorganic seawater constituents which have diversified considerably and now require more space for their description than before. Methods to determine volatile halocarbons, dimethyl sulphide, photosynthetic pigments and natural radioactive tracers have been added as well as applications of X-ray fluorescence spectroscopy and various electrochemical methods for trace metal analysis. Another method not previously described deals with the determination of the partial pressure of carbon dioxide as part of standardised procedures to describe the marine CO2 system.
Download or read book Principles of Food Sanitation written by Norman G. Marriott and published by Springer Science & Business Media. This book was released on 2013-03-09 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: Large volume food processing and preparation operations have increased the need for improved sanitary practices from processing to consumption. This trend presents a challenge to every employee in the food processing and food prepara tion industry. Sanitation is an applied science for the attainment of hygienic conditions. Because of increased emphasis on food safety, sanitation is receiving increased attention from those in the food industry. Traditionally, inexperienced employees with few skills who have received little or no training have been delegated sanitation duties. Yet sanitation employees require intensive training. In the past, these employees, including sanitation program managers, have had only limited access to material on this subject. Technical information has been confined primarily to a limited number of training manuals provided by regulatory agen cies, industry and association manuals, and recommendations from equipment and cleaning compound firms. Most of this material lacks specific information related to the selection of appropriate cleaning methods, equipment, compounds, and sanitizers for maintaining hygienic conditions in food processing and prepara tion facilities. The purpose of this text is to provide sanitation information needed to ensure hygienic practices. Sanitation is a broad subject; thus, principles related to con tamination, cleaning compounds, sanitizers, and cleaning equipment, and specific directions for applying these principles to attain hygienic conditions in food processing and food preparation are discussed. The discussion starts with the importance of sanitation and also includes regulatory requirements and voluntary sanitation programs including additional and updated information on Hazard Analysis Critical Control Points (HACCP).
Download or read book Clean In Place for Biopharmaceutical Processes written by Dale A. Seiberling and published by CRC Press. This book was released on 2007-10-15 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: An invaluable source instruction on the principles, instrumentation, design, implementation, operation, and maintenance of an effective clean-in-place system (CIP), this guide illustrates best practices and successful applications of CIP in both pharmaceutical and biotechnology facilities. Offering reader-friendly descriptions of the various types of equipment and materials found in typical CIP processes, Clean-In-Place For Biopharmaceutical Processes will take the guess-work out of CIP development, and illustrate all one needs to know for the establishment and optimal functioning of a CIP system.
Download or read book Green Corrosion Inhibitors written by V. S. Sastri and published by John Wiley & Sons. This book was released on 2012-02-14 with total page 267 pages. Available in PDF, EPUB and Kindle. Book excerpt: A book to cover developments in corrosion inhibitors is long overdue. This has been addressed by Dr Sastri in a book which presents fundamental aspects of corrosion inhibition, historical developments and the industrial applications of inhibitors. The book deals with the electrochemical principles and chemical aspects of corrosion inhibition, such as stability of metal complexes, the Hammett equation, hard and soft acid and base principle, quantum chemical aspects and Hansch' s model and also with the various surface analysis techniques, e.g. XPS, Auger, SIMS and Raman spectroscopy, that are used in industry for corrosion inhibition. The applications of corrosion inhibition are wide ranging. Examples given in this book include: oil and gas wells, petrochemical plants, steel reinforced cement, water cooling systems, and many more. The final chapters discuss economic and environmental considerations which are now of prime importance. The book is written for researchers in academia and industry, practicing corrosion engineers and students of materials science, engineering and applied chemistry.
Download or read book Advanced Oxidation Processes for Water and Wastewater Treatment written by Simon Parsons and published by IWA Publishing. This book was released on 2004-03-01 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: The suitability of Advanced Oxidation Processes (AOPs) for pollutant degradation was recognised in the early 1970s and much research and development work has been undertaken to commercialise some of these processes. AOPs have shown great potential in treating pollutants at both low and high concentrations and have found applications as diverse as ground water treatment, municipal wastewater sludge destruction and VOCs control. Advanced Oxidation Processes for Water and Wastewater Treatment is an overview of the advanced oxidation processes currently used or proposed for the remediation of water, wastewater, odours and sludge. The book contains two opening chapters which present introductions to advanced oxidation processes and a background to UV photolysis, seven chapters focusing on individual advanced oxidation processes and, finally, three chapters concentrating on selected applications of advanced oxidation processes. Advanced Oxidation Processes for Water and Wastewater Treatment will be invaluable to readers interested in water and wastewater treatment processes, including professionals and suppliers, as well as students and academics studying in this area. Dr Simon Parsons is a Senior Lecturer in Water Sciences at Cranfield University with ten years' experience of industrial and academic research and development.
Download or read book Aquatic and Surface Photochemistry written by George R. Helz and published by CRC Press. This book was released on 2018-01-10 with total page 665 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aquatic and Surface Photochemistry provides a broad overview of current research in the emerging field of environmental aquatic and surface photochemistry. Selected reviews and current research articles are blended to provide an in-depth treatment of various aspects of this research area. The first part of the text deals with photochemistry in the environment, covering recent research on the following topics: aquatic photochemistry of organic pollutants and agrochemicals, photochemical cycling of carbon and transition metals (especially iron), photochemical formation of reactive oxygen species in natural waters, photoreaction in cloud and rain droplets, and photoreactions on environmental surfaces (soil, ash, metal, oxide). The second part provides discussions and data on both heterogeneous photocatalytic and homogeneous processes, with topics ranging from applications to mechanistic studies. These chapters illustrate the wide diversity of pollutant classes that are degradable by photochemical techniques and the effects of various reaction conditions on the rates and efficiency of the techniques. Current kinetic studies are presented, which provide new information about the role of adsorption and the nature of the reactive oxidizing species that mediate these photoremediation processes.This book will interest civil, chemical, and environmental engineers, as well as chemists, soil scientists, geochemists, and atmospheric chemists.
Download or read book Chemical Oxidation Applications for Industrial Wastewaters written by Olcay Tunay and published by IWA Publishing. This book was released on 2010-10-12 with total page 361 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the most recent scientific and technological developments (state-of-the-art) in the field of chemical oxidation processes applicable for the efficient treatment of biologically-difficult-to-degrade, toxic and/or recalcitrant effluents originating from different manufacturing processes. It is a comprehensive review of process and pollution profiles as well as conventional, advanced and emerging treatment processes & technologies developed for the most relevant and pollution (wet processing)-intensive industrial sectors. It addresses chemical/photochemical oxidative treatment processes, case-specific treatability problems of major industrial sectors, emerging (novel) as well as pilot/full-scale applications, process integration, treatment system design & sizing criteria (figure-of-merits), cost evaluation and success stories in the application of chemical oxidative treatment processes. Chemical Oxidation Applications for Industrial Wastewaters is an essential reference for lecturers, researchers, industrial and environmental engineers and practitioners working in the field of environmental science and engineering. Visit the IWA WaterWiki to read and share material related to this title: http://www.iwawaterwiki.org/xwiki/bin/view/Articles/CHEMICALOXIDATIONAPPLICATIONSFORINDUSTRIALWASTEWATERS Authors: Professor Olcay Tünay, Professor Isik Kabdasli, Associate Professor Idil Arslan-Alaton and Assistant Professor Tugba Ölmez-Hanci, Environmental Engineering Department, Istanbul Technical University, Turkey.
Download or read book Corrosion Prevention and Protection written by Edward Ghali and published by John Wiley & Sons. This book was released on 2007-01-30 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion Prevention and Protection: Practical Solutions presents a functional approach to the various forms of corrosion, such as uniform corrosion, pitting corrosion, crevice corrosion, galvanic corrosion, stress corrosion, hydrogen-induced damage, sulphide stress cracking, erosion-corrosion, and corrosion fatigue in various industrial environments. The book is split into two parts. The first, consisting of five chapters: Introduction and Principles (Fundamentals) of Corrosion Corrosion Testing, Detection, Monitoring and Failure Analysis Regulations, Specifications and Safety Materials: Metals, Alloys, Steels and Plastics Corrosion Economics and Corrosion Management The second part of the book consists of two chapters which present: a discussion of corrosion reactions, media, active and active-passive corrosion behaviour and the various forms of corrosion, a collection of case histories and practical solutions which span a wide range of industrial problems in a variety of frequently encountered environments, including statues & monuments, corrosion problems in metallurgical and mineral processing plants, boilers, heat exchangers and cooling towers, aluminum and copper alloys, galvanized steel structures as well as hydrogeological environmental corrosion This text is relevant to researchers and practitioners, engineers and chemists, working in corrosion in industry, government laboratories and academia. It is also suitable as a course text for engineering students as well as libraries related to chemical and chemical engineering institutes and research departments.
Download or read book Materials and Processes written by Barrie D. Dunn and published by Springer. This book was released on 2015-12-29 with total page 677 pages. Available in PDF, EPUB and Kindle. Book excerpt: The objective of this book is to assist scientists and engineers select the ideal material or manufacturing process for particular applications; these could cover a wide range of fields, from light-weight structures to electronic hardware. The book will help in problem solving as it also presents more than 100 case studies and failure investigations from the space sector that can, by analogy, be applied to other industries. Difficult-to-find material data is included for reference. The sciences of metallic (primarily) and organic materials presented throughout the book demonstrate how they can be applied as an integral part of spacecraft product assurance schemes, which involve quality, material and processes evaluations, and the selection of mechanical and component parts. In this successor edition, which has been revised and updated, engineering problems associated with critical spacecraft hardware and the space environment are highlighted by over 500 illustrations including micrographs and fractographs. Space hardware captured by astronauts and returned to Earth from long durations in space are examined. Information detailed in the Handbook is applicable to general terrestrial applications including consumer electronics as well as high reliability systems associated with aeronautics, medical equipment and ground transportation. This Handbook is also directed to those involved in maximizing the relia bility of new materials and processes for space technology and space engineering. It will be invaluable to engineers concerned with the construction of advanced structures or mechanical and electronic sub-systems.
Download or read book Modern Aspects of Electrochemistry 42 written by Constantinos G. Vayenas and published by Springer Science & Business Media. This book was released on 2008-03-08 with total page 434 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume analyzes and summarizes recent developments in several key interfacial electrochemical systems in the areas of fuel cell electrocatatalysis, electrosynthesis and electrodeposition. The six Chapters are written by internationally recognized experts in these areas and address both fundamental and practical aspects of several existing or emerging key electrochemical technologies. The Chapter by R. Adzic, N. Marinkovic and M. Vukmirovic provides a lucid and authoritative treatment of the electrochemistry and electrocatalysis of Ruthenium, a key element for the devel- ment of efficient electrodes for polymer electrolyte (PEM) fuel cells. Starting from fundamental surface science studies and interfacial considerations, this up-to-date review by some of the pioneers in this field, provides a deep insight in the complex catalytic-electrocatalytic phenomena occurring at the interfaces of PEM fuel cell electrodes and a comprehensive treatment of recent developments in this extremely important field. Several recent breakthroughs in the design of solid oxide fuel cell (SOFC) anodes and cathodes are described in the Chapter of H. Uchida and M. Watanabe. The authors, who have pioneered several of these developments, provide a lucid presentation d- cribing how careful fundamental investigations of interfacial electrocatalytic anode and cathode phenomena lead to novel electrode compositions and microstructures and to significant practical advances of SOFC anode and cathode stability and enhanced electrocatalysis.
