Download or read book Illumination Guidelines for Nighttime Highway Work written by Ralph D. Ellis (Ph.D.) and published by Transportation Research Board. This book was released on 2003 with total page 83 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Illumination Guidelines for Nighttime Highway Work written by Ralph D. Ellis (Civil engineer) and published by . This book was released on 1996 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Illumination Guidelines for Nighttime Highway Work written by Transportation Research Board. National Cooperative Highway Research Program and published by . This book was released on 1996 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Roadway Lighting Design Guide written by American Association of State Highway and Transportation Officials and published by AASHTO. This book was released on 2005 with total page 134 pages. Available in PDF, EPUB and Kindle. Book excerpt: This guide replaces the 1984 publication entitled An Informational Guide for Roadway Lighting. It has been revised and brought up to date to reflect current practices in roadway lighting. The guide provides a general overview of lighting systems from the point of view of the transportation departments and recommends minimum levels of quality. The guide incorporates the illuminance and luminance design methods, but does not include the small target visibility (STV) method.

Download or read book A Guidebook for Nighttime Construction written by Jennifer Sue Shane and published by Transportation Research Board. This book was released on 2012 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: "TRB's National Cooperative Highway Research Program (NCHRP) Report 726: A Guidebook for Nighttime Construction: Impacts on Safety, Quality, and Productivity provides suggested guidance on the conduct of nighttime highway construction and maintenance operations. These guidelines are based on best practices and strategies for nighttime operations that relate to the personnel and traveling public safety and the quality of the as-built facility. The guide also addresses work-zone risk analysis planning and implementation, construction nuisances to both neighbors and workers, and work-zone illumination methods."--Publisher's description.

Download or read book Guidelines for Design and Operation of Nighttime Traffic Control for Highway Maintenance and Construction written by James E. Bryden and published by Transportation Research Board. This book was released on 2002 with total page 131 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Evaluation of Glare and Lighting Performance in Nighttime Highway Construction Projects written by Ibrahim S. Odeh and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: An increasing amount of highway repair and construction work is being performed during the off-peak nighttime hours. Nighttime construction is advocated as a way to mitigate the impact of construction operations on the traveling public, shorten the duration of construction operations, and reduce the potential for work zone accidents. However, the utilization and placement of lighting equipment to illuminate the work zone may cause harmful levels of glare for the traveling public. This type of nighttime glare needs to be controlled and minimized to ensure safety for the traveling public and construction workers. This research study focused on studying the veiling luminance ratio (glare) experienced by drive-by motorists in lanes adjacent to nighttime work zones. The major objectives of this study are to: (1) provide an in-depth comprehensive review of the latest literature on the causes of glare and the existing practices that can be used to quantify and control glare during nighttime highway construction; (2) identify practical factors that affect the measurement of veiling luminance ratio (glare) in and around nighttime work zones; (3) analyze and compare the levels of glare and lighting performance generated by typical lighting arrangements in nighttime highway construction; (4) evaluate the impact of lighting design parameters on glare and provide practical recommendations to reduce and control lighting glare in and around nighttime work zones; (5) develop a practical model that can be utilized by resident engineers and contractors to measure and quantify veiling luminance ratio (glare) experienced by drive-by motorists near nighttime highway construction sites; and (6) investigate and analyze existing recommendations on the maximum allowable levels of veiling luminance ratio (glare) that can be tolerated by nighttime drivers from similar lighting sources. In order to achieve these objectives, the study was conducted in four major tasks that focused on: (1) conducting a comprehensive literature review; (2) visiting and studying a number of nighttime highway construction projects; (3) conducting field studies to evaluate the performance of selected lighting arrangements; and (4) developing practical models to measure and control the levels of glare experienced by drive-by motorists in lanes adjacent to nighttime work zones. In the first task of the project, a comprehensive literature review was conducted to study the latest research and developments on veiling luminance ratio (glare) and its effects on drivers and construction workers during nighttime highway construction work. Sources of information included publications from professional societies, journal articles, on-line databases, and contacts from DOT0́9s. The review of the literature focused on: (1) lighting requirements for nighttime highway construction; (2) causes and sources of glare in nighttime work zones, including fixed roadway lighting, vehicles headlamps, and nighttime lighting equipment in the work zone; (3) the main types of glare which can be classified based on its source as either direct or reflected glare; and based on its impact as discomfort, disabling, or blinding glare; (4) available procedures to measure and quantify discomfort and disabling glare; (5) existing methods to quantify pavement/adaptation luminance which is essential in measuring discomfort and disabling glare; (6) available recommendations by State DOTs and professional organizations to control glare; and (7) existing guidelines and hardware for glare control. The second task involved site visits to a number of nighttime work zones to identify practical factors that affect the measurement of the veiling luminance ratio in nighttime construction sites. The site visits were conducted over a five-month period in order to gather data on the type of construction operations that are typically performed during nighttime hours, the type of lighting equipment used to illuminate the work area, and the levels of glare experienced by workers and motorists in and around the work zone. One of the main findings of these site visits was identifying a number of challenges and practical factors that significantly affect the measurement and quantification of the veiling luminance ratio (glare) in nighttime work zones. These practical factors were carefully considered during the development of the glare measurement model in this study to ensure its practicality and ease of use in nighttime work zones by resident engineers and contractors alike. Another important finding of the site visits was the observation that improper utilization and setup of construction lighting equipment may cause significant levels of glare for construction workers and drive-by motorists. In the third task, field experiments were conducted to study and evaluate the levels of lighting glare caused by commonly used lighting equipment in nighttime work zones. During these experiments, a total of 25 different lighting arrangements were tested over a period of 33 days from May 10, 2007 to June 12, 2007 at the Illinois Center for Transportation (ICT) in the University of Illinois at Urbana-Champaign. The objectives of these experiments were to: (1) analyze and compare the levels of glare and lighting performance generated by typical lighting arrangements in nighttime highway construction; and (2) provide practical recommendations for lighting arrangements to reduce and control lighting glare in and around nighttime work zones. The field tests were designed to evaluate the levels of glare and lighting performance generated by commonly used construction lighting equipment, including one balloon light, two balloon lights, three balloon lights, one light tower and one Nite Lite. The tests were also designed to study the impact of tested lighting parameters (i.e., type of light, height of light, aiming and rotation angles of light towers, and height of vehicle/observer) on the veiling luminance ratio experienced by drive-by motorists as well as their impact on the average horizontal illuminance and lighting uniformity ratio in the work area. Based on the findings from these tests, a number of practical recommendations were provided to control and reduce veiling luminance ratio/glare in and around nighttime work zones. The final (fourth) task of this study focused on the development of a practical model to measure and quantify veiling luminance ratio (glare) experienced by drive-by motorists in lanes adjacent to nighttime work zones. The model was designed to consider the practical factors that were identified during the site visits, including the need to provide a robust balance between practicality and accuracy to ensure that it can be efficiently and effectively used by resident engineers on nighttime highway construction sites. To ensure practicality, the model enables resident engineers to measure the required vertical illuminance data in safe locations inside the work zone while allowing the traffic in adjacent lanes to flow uninterrupted. These measurements can then be analyzed by newly developed regression models to accurately calculate the vertical illuminance values experienced by drivers from which the veiling luminance ratio (glare) can be derived. This task also analyzed existing recommendations on the maximum allowable levels of veiling luminance ratio (glare) that can be tolerated by nighttime drivers from various lighting sources, including roadway lighting, headlights of opposite traffic vehicles, and lighting equipment in nighttime work zones. The main research development of this study contribute to the advancement of current practice in highway construction and can lead to an increase in the safety of construction workers and the traveling public in and around the nighttime work zones. The outcome of this study will help in: (1) identifying practical factors and challenges that affect the measurements of glare in and around nighttime work zones; (2) evaluating and comparing the lighting performance and glare levels of typical construction lighting equipment that are commonly used in nighttime highway construction projects; (3) recommending practical lighting arrangements that generate acceptable levels of lighting glare for motorists and adequate levels of lighting performance for construction workers inside the work zone; (4) developing practical and safe model for measuring and quantifying the veiling luminance ratio experienced by drive-by motorists near nighttime highway construction sites; and (5) providing a baseline for Departments of Transportation (DOTs) to develop specifications and standards on how to control and quantify the levels of glare in nighttime highway construction projects.

Download or read book Nighttime Highway Construction Illumination written by John D. Bullough and published by . This book was released on 2014 with total page 79 pages. Available in PDF, EPUB and Kindle. Book excerpt: The nighttime driving environment, consisting of roadway illumination, signs, vehicle lighting and markers, delineators and flashing lights, can be complex or even confusing for both pedestrians and drivers. The nighttime construction environment is even more complex and even chaotic because of the added presence of workers, construction equipment and bright lights (which are sometimes flashing). Work zones at night often involve changing conditions and new traffic patterns that are unfamiliar to drivers. Workers in highway construction areas and drivers navigating through these areas have distinct visual requirements that must be met both through lighting and other forms of visual information provided in the work zone. Conventional methods for illuminating work zones are prone to producing glare for workers and for drivers. At the same time, new technologies for lighting and traffic control, such as balloon lights, light emitting diodes (LEDs), highly reflective retroreflective sheeting and intelligent warning lights are being developed that could address many of the concerns associated with nighttime highway construction. As part of a multi-phase project, requirements for worker and driver visibility and visual information were identified through human factors research, and various technologies and new approaches to work zone lighting and traffic control were demonstrated and evaluated to provide preliminary guidance for when they might be of benefit. A checklist of planning and design issues, and a method for estimating visual performance under nighttime work zone lighting are provided to help transportation engineers and highway contractors identify promising solutions for work zone lighting.

Download or read book Guidance for Implementation of the AASHTO Strategic Highway Safety Plan written by Nicholas D. Antonucci and published by Transportation Research Board. This book was released on 2005 with total page 177 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Nationally Coordinated Program of Highway Research Development and Technology Annual Progress Report Fiscal Year 1994 written by and published by . This book was released on 1995 with total page 168 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Traffic Control Handbook for Mobile Operations at Night written by James E. Bryden and published by . This book was released on 2003 with total page 60 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Research Results Digest National Cooperative Highway Research Program written by National Cooperative Highway Research Program and published by . This book was released on 2009 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Development of a Model for Determining Workzone Illumination Requirements During Nighttime Highway Construction written by Ashish Kumar and published by . This book was released on 1994 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Research Results Digest written by and published by . This book was released on 1993 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Structural Construction Conf written by Franco Bontempi and published by CRC Press. This book was released on 2003-01-01 with total page 978 pages. Available in PDF, EPUB and Kindle. Book excerpt: Objective of conference is to define knowledge and technologies needed to design and develop project processes and to produce high-quality, competitive, environment- and consumer-friendly structures and constructed facilities. This goal is clearly related to the development and (re)-use of quality materials, to excellence in construction management and to reliable measurement and testing methods.

Download or read book Roadway Lighting ANSI IES RP 8 14 written by Illuminating Engineering Society and published by . This book was released on 2014-10-10 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book An Informational Guide for Roadway Lighting written by American Association of State Highway Officials. Committee on Planning and Design Policies and published by . This book was released on 1969 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: