Download or read book IEEE Recommended Practice for Testing Insulation Resistance of Rotating Machinery written by and published by IEEE Standards Office. This book was released on 2000 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt: This document describes the recommended procedure for measuring insulation resistance of armature and field windings in rotating machines rated 1 hp, 750 W or greater. It applies to synchronous machines, induction machines, dc machines, and synchronous condensers. Contained within this document is the general theory of insulation resistance (IR) and polarization index (P.I.), as well as factors affecting the results, test procedures, methods of interpretation, test limitations, and recommended minimum values.

Download or read book Electrical Power Equipment Maintenance and Testing written by Paul Gill and published by CRC Press. This book was released on 1997-10-01 with total page 626 pages. Available in PDF, EPUB and Kindle. Book excerpt: This practical guide provides comprehensive and up-to-date information on the testing and maintenance of electrical power systems equipment and apparatus found in utility, industrial, commercial, and institutional facilities-demonstrating when and how to perform the appropriate tests to ensure maximum operational reliability. Integrating basic principles, theory, and practice, the book discusses routine and preoperational testing and maintenance procedures for assessing equipment reliability and dependability and shows how to inspect and test equipment and apparatus insulation integrity and other operating characteristics affecting performance.

Download or read book Electrical Codes Standards Recommended Practices and Regulations written by Robert J. Alonzo and published by William Andrew. This book was released on 2009-12-21 with total page 511 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electrical codes, standards, recommended practices and regulations can be complex subjects, yet are essential in both electrical design and life safety issues.This book demystifies their usage.It is a handbook of codes, standards, recommended practices and regulations in the United States involving electrical safety and design. Many engineers and electrical safety professionals may not be aware of all of those documents and their applicability. This book identifies those documents by category, allowing the ready and easy access to the relevant requirements. Because these documents may be updated on a regular basis, this book was written so that its information is not reliant on the latest edition or release of those codes, standards, recommended practices or regulations.No single document on the market today attempts to not only list the majority of relevant electrical design and safety codes, standards, recommended practices and regulations, but also explain their use and updating cycles. This book, one-stop-information-center for electrical engineers, electrical safety professionals, and designers, does. - Covers the codes, standards, recommended practices and regulations in the United States involving electrical safety and design, providing a comprehensive reference for engineers and electrical safety professionals - Documents are identified by category, enabling easy access to the relevant requirements - Not version-specific; information is not reliant on the latest edition or release of the codes, standards, recommended practices or regulations

Download or read book Electrical Insulation for Rotating Machines written by Greg C. Stone and published by John Wiley & Sons. This book was released on 2014-07-21 with total page 685 pages. Available in PDF, EPUB and Kindle. Book excerpt: A fully expanded new edition documenting the significant improvements that have been made to the tests and monitors of electrical insulation systems Electrical Insulation for Rotating Machines: Design, Evaluation, Aging, Testing, and Repair, Second Edition covers all aspects in the design, deterioration, testing, and repair of the electrical insulation used in motors and generators of all ratings greater than fractional horsepower size. It discusses both rotor and stator windings; gives a historical overview of machine insulation design; and describes the materials and manufacturing methods of the rotor and stator winding insulation systems in current use (while covering systems made over fifty years ago). It covers how to select the insulation systems for use in new machines, and explains over thirty different rotor and stator winding failure processes, including the methods to repair, or least slow down, each process. Finally, it reviews the theoretical basis, practical application, and interpretation of forty different tests and monitors that are used to assess winding insulation condition, thereby helping machine users avoid unnecessary machine failures and reduce maintenance costs. Electrical Insulation for Rotating Machines: Documents the large array of machine electrical failure mechanisms, repair methods, and test techniques that are currently available Educates owners of machines as well as repair shops on the different failure processes and shows them how to fix or otherwise ameliorate them Offers chapters on testing, monitoring, and maintenance strategies that assist in educating machine users and repair shops on the tests needed for specific situations and how to minimize motor and generator maintenance costs Captures the state of both the present and past “art” in rotating machine insulation system design and manufacture, which helps designers learn from the knowledge acquired by previous generations An ideal read for researchers, developers, and manufacturers of electrical insulating materials for machines, Electrical Insulation for Rotating Machines will also benefit designers of motors and generators who must select and apply electrical insulation in machines.

Download or read book Handbook of Large Turbo Generator Operation and Maintenance written by Geoff Klempner and published by John Wiley & Sons. This book was released on 2018-06-15 with total page 1036 pages. Available in PDF, EPUB and Kindle. Book excerpt: The comprehensive guide for large turbo-generator operation and maintenance The Handbook of Large Turbo-Generator Operation and Maintenance is an expanded 3rd edition of the authors’ second edition of the same book. This updated revision covers additional topics on generators and provides more depth on existing topics. It is the ultimate resource for operators and inspectors of large utility and industrial generating facilities who deal with multiple units of disparate size, origin, and vintage. The book is also an excellent learning tool for students, consulting and design engineers. It offers the complete scope of information regarding operation and maintenance of all types of turbine-driven generators found in the world. Based on the authors' ver eighty combined years of generating station and design work experience, the information presented in the book is designed to inform the reader about actual machine operational problems and failure modes that occur in generating stations and other types of facilities. Readers will find very detailed coverage of: Design and construction of generators and auxiliary systems Generator operation and control, including interaction with the grid Monitoring, diagnostics, and protection of turbo-generators Inspection practices for the stator, rotor, and auxiliary systems Maintenance testing, including electrical and non-destructive examination Ideas on maintenance strategies and life cycle management Additional topics on uprating of generators and long term storage are also included The Handbook of Large Turbo-Generator Operation and Maintenance comes packed with photos and graphs, commonly used inspection forms, and extensive references for each topic. It is an indispensable reference for anyone involved in the design, construction, operation, protection, maintenance, and troubleshooting of large generators in generating stations and industrial power facilities.

Download or read book Operation and Maintenance of Large Turbo Generators written by Geoff Klempner and published by John Wiley & Sons. This book was released on 2004-08-11 with total page 590 pages. Available in PDF, EPUB and Kindle. Book excerpt: The comprehensive guide for the operation and maintenance of large turbo-generators Operation and Maintenance of Large Turbo-Generators is the ultimate resource for operators and inspectors of large utility and industrial generating facilities who deal with multiple units of disparate size, origin, and vintage. It offers the complete scope of information regarding operation and maintenance of all types of turbine-driven generators built in the world. Based on the authors’ combined sixty years of generating station and design work experience, the information presented in the book is designed to inform the reader about actual machine operational problems and failure modes that occur in generating stations and other types of facilities. Readers will find very detailed coverage of: Design and construction of generators and auxiliary systems Generator operation, including interaction with the grid Monitoring, diagnostics, and protection of turbo-generators Inspection practices, including stator, rotor, and auxiliary systems Ideas for improving plant reliability and reducing costs and electrical failures Maintenance testing, including electrical and nondestructive examination Operation and Maintenance of Large Turbo-Generators comes filled with photos and graphs, commonly used inspection forms, and extensive references for each topic. It is an indispensable resource for anyone involved in the design, construction, protection, operation, maintenance, and troubleshooting of large generators in generating stations and industrial power facilities. The book is also an excellent learning tool for students, consultants, and design engineers.

Download or read book Handbook of Electric Motors written by Hamid A. Toliyat and published by CRC Press. This book was released on 2018-10-03 with total page 850 pages. Available in PDF, EPUB and Kindle. Book excerpt: Presenting current issues in electric motor design, installation, application, and performance, this second edition serves as the most authoritative and reliable guide to electric motor utilization and assessment in the commercial and industrial sectors. Covering topics ranging from motor energy and efficiency to computer-aided design and equipment selection, this reference assists professionals in all aspects of electric motor maintenance, repair, and optimization. It has been expanded by more than 40 percent to explore the most influential technologies in the field including electronic controls, superconducting generators, recent analytical tools, new computing capabilities, and special purpose motors.

Download or read book IEEE Standards written by Institute of Electrical and Electronics Engineers and published by . This book was released on 1996 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book NIST Handbook written by and published by . This book was released on 1989 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Electrical Power Equipment Maintenance and Testing Second Edition written by Paul Gill and published by CRC Press. This book was released on 2008-12-22 with total page 1002 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of a bestseller, this definitive text covers all aspects of testing and maintenance of the equipment found in electrical power systems serving industrial, commercial, utility substations, and generating plants. It addresses practical aspects of routing testing and maintenance and presents both the methodologies and engineering basics needed to carry out these tasks. It is an essential reference for engineers and technicians responsible for the operation, maintenance, and testing of power system equipment. Comprehensive coverage includes dielectric theory, dissolved gas analysis, cable fault locating, ground resistance measurements, and power factor, dissipation factor, DC, breaker, and relay testing methods.

Download or read book Mechanical Design of Electric Motors written by Wei Tong and published by CRC Press. This book was released on 2014-04-28 with total page 736 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rapid increases in energy consumption and emphasis on environmental protection have posed challenges for the motor industry, as has the design and manufacture of highly efficient, reliable, cost-effective, energy-saving, quiet, precisely controlled, and long-lasting electric motors.Suitable for motor designers, engineers, and manufacturers, as well

Download or read book Mechanical Design and Manufacturing of Electric Motors written by Wei Tong and published by CRC Press. This book was released on 2022-05-20 with total page 1070 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Second Edition of Mechanical Design and Manufacturing of Electric Motors provides in-depth knowledge of design methods and developments of electric motors in the context of rapid increases in energy consumption, and emphasis on environmental protection, alongside new technology in 3D printing, robots, nanotechnology, and digital techniques, and the challenges these pose to the motor industry. From motor classification and design of motor components to model setup and material and bearing selections, this comprehensive text covers the fundamentals of practical design and design-related issues, modeling and simulation, engineering analysis, manufacturing processes, testing procedures, and performance characteristics of electric motors today. This Second Edition adds three brand new chapters on motor breaks, motor sensors, and power transmission and gearing systems. Using a practical approach, with a focus on innovative design and applications, the book contains a thorough discussion of major components and subsystems, such as rotors, shafts, stators, and frames, alongside various cooling techniques, including natural and forced air, direct- and indirect-liquid, phase change, and other newly-emerged innovative cooling methods. It also analyzes the calculation of motor power losses, motor vibration, and acoustic noise issues, and presents engineering analysis methods and case-study results. While suitable for motor engineers, designers, manufacturers, and end users, the book will also be of interest to maintenance personnel, undergraduate and graduate students, and academic researchers.

Download or read book 43 1974 IEEE Recommended Practice for Testing Insulation Resistance of Rotating Machinery written by and published by . This book was released on with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Large Hydro Generators written by Glenn Mottershead and published by John Wiley & Sons. This book was released on 2020-11-11 with total page 674 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers comprehensive coverage of the operation and maintenance of large hydro generators This book is a practical handbook for engineers and maintenance staff responsible for the upkeep of large salient-pole hydro generators used in electric power plants. Focusing on the physics and maintenance of large vertical salient pole generators, it offers readers real-world experience, problem description, and solutions, while teaching them about the design, modernization, inspections, maintenance, and operation of salient pole machines. Handbook of Large Hydro Generators: Operation and Maintenance provides an introduction to the principles of operation of synchronous machines. It then covers design and construction, auxiliary systems, operation and control, and monitoring and diagnostics of generators. Generator protection, inspection practices and methodology and auxiliaries inspections are also examined. The final two chapters are dedicated to maintenance and testing, and maintenance philosophies, upgrades, and uprates. The handbook includes over 420 color photos and 180 illustrations, forms, and tables to complement the topics covered in the chapters. Written with a machine operator and inspector in mind, Handbook of Large Hydro Generators: Operation and Maintenance: Instructs readers how to perform complete machine inspections, understand what they are doing, and find solutions for any problems encountered Includes real-life, practical, field experiences so that readers can familiarize themselves with aspects of machine operation, maintenance, and solutions to common problems Benefits experienced and new power plant operators, generator design engineers and operations engineers. Is authored by industry experts who participated in the writing and maintenance of IEEE standards (IEEE C50.12 and C50.13) on the subject Handbook of Large Hydro Generators: Operation and Maintenance is an ideal resource for scientists and engineers whose research interest is in electromagnetic and energy conversion. It is also an excellent book for senior undergraduate and graduate students majoring in energy generation, and generator operation and maintenance.

Download or read book Offshore Electrical Engineering Manual written by Geoff MacAngus-Gerrard and published by Gulf Professional Publishing. This book was released on 2017-11-06 with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt: Offshore Electrical Engineering Manual, Second Edition, is for electrical engineers working on offshore projects who require detailed knowledge of an array of equipment and power distribution systems. The book begins with coverage of different types of insulation, hot-spot temperatures, temperature rise, ambient air temperatures, basis of machine ratings, method of measurement of temperature rise by resistance, measurement of ambient air temperature. This is followed by coverage of AC generators, automatic voltage regulators, AC switchgear transformers, and programmable electronic systems. The emphasis throughout is on practical, ready-to-apply techniques that yield immediate and cost-effective benefits. The majority of the systems covered in the book operate at a nominal voltage of 24 y dc and, although it is not necessary for each of the systems to have separate battery and battery charger systems, the grouping criteria require more detailed discussion. The book also provides information on equipment such as dual chargers and batteries for certain vital systems, switchgear tripping/closing, and engine start batteries which are dedicated to the equipment they supply. In the case of engines which drive fire pumps, duplicate charges and batteries are also required. Packed with charts, tables, and diagrams, this work is intended to be of interest to both technical readers and to general readers. It covers electrical engineering in offshore situations, with much of the information gained in the North Sea. Some topics covered are offshore power requirements, generator selection, process drivers and starting requirements, control and monitoring systems, and cabling and equipment installation - Discusses how to perform inspections of electrical and instrument systems on equipment using appropriate regulations and specifications - Explains how to ensure electrical systems/components are maintained and production is uninterrupted - Demonstrates how to repair, modify, and install electrical instruments ensuring compliance with current regulations and specifications - Covers specification, management, and technical evaluation of offshore electrical system design - Features evaluation and optimization of electrical system options including DC/AC selection and offshore cabling designs

Download or read book Electrical Insulation for Rotating Machines written by Greg C. Stone and published by John Wiley & Sons. This book was released on 2014-07-02 with total page 685 pages. Available in PDF, EPUB and Kindle. Book excerpt: A fully expanded new edition documenting the significant improvements that have been made to the tests and monitors of electrical insulation systems Electrical Insulation for Rotating Machines: Design, Evaluation, Aging, Testing, and Repair, Second Edition covers all aspects in the design, deterioration, testing, and repair of the electrical insulation used in motors and generators of all ratings greater than fractional horsepower size. It discusses both rotor and stator windings; gives a historical overview of machine insulation design; and describes the materials and manufacturing methods of the rotor and stator winding insulation systems in current use (while covering systems made over fifty years ago). It covers how to select the insulation systems for use in new machines, and explains over thirty different rotor and stator winding failure processes, including the methods to repair, or least slow down, each process. Finally, it reviews the theoretical basis, practical application, and interpretation of forty different tests and monitors that are used to assess winding insulation condition, thereby helping machine users avoid unnecessary machine failures and reduce maintenance costs. Electrical Insulation for Rotating Machines: Documents the large array of machine electrical failure mechanisms, repair methods, and test techniques that are currently available Educates owners of machines as well as repair shops on the different failure processes and shows them how to fix or otherwise ameliorate them Offers chapters on testing, monitoring, and maintenance strategies that assist in educating machine users and repair shops on the tests needed for specific situations and how to minimize motor and generator maintenance costs Captures the state of both the present and past “art” in rotating machine insulation system design and manufacture, which helps designers learn from the knowledge acquired by previous generations An ideal read for researchers, developers, and manufacturers of electrical insulating materials for machines, Electrical Insulation for Rotating Machines will also benefit designers of motors and generators who must select and apply electrical insulation in machines.

Download or read book Handbook of Pumps and Pumping written by Brian Nesbitt and published by Elsevier. This book was released on 2006-10-18 with total page 499 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by an experienced engineer, this book contains practical information on all aspects of pumps including classifications, materials, seals, installation, commissioning and maintenance. In addition you will find essential information on units, manufacturers and suppliers worldwide, providing a unique reference for your desk, R&D lab, maintenance shop or library.* Includes maintenance techniques, helping you get the optimal performance out of your pump and reducing maintenance costs * Will help you to understand seals, couplings and ancillary equipment, ensuring systems are set up properly to save time and money * Provides useful contacts for manufacturers and suppliers who specialise in pumps, pumping and ancillary equipment