Download or read book High strength steel Forgings written by H. J. Henning and published by . This book was released on 1961 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt: THIS REPORT IS MAINLY CONCERNED WITH FORGINGS MADE FROM MARTENSITIC STEELS HEAT TREATED TO STRENGTHS RANGING FROM 240,000 TO 300,000 PSI. FORGING CHARACTERISTICS, DESIGN LIMITATIONS, DIMENSIONAL TOLERANCES, AND QUALITY-CONTROL PROBLEMS ARE DISCUSSED. A CONSIDERABLE AMOUNT OF DATA ON MECHANICAL PROPERTIES IS ALSO PRESENTED. IN ADDITION, THE REPORT SUMMARIZES THE AVAILABLE INFORMATION ON FORGED, SEMIAUSTENITIAL STEELS. THIS COMPILATION IS BASED ON PUBLISHED ARTICLES, GOVERNMENT REPORTS, AND INTERVIEWS WITH PRODUCERS AND USERS OF STEEL FORGINGS.

Download or read book Heat Treater s Guide written by Harry Chandler and published by ASM International. This book was released on 1994-12-31 with total page 920 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edition is a complete revision and contains a great deal of new subject matter including information on ferrous powder metallurgy, cast irons, ultra high strength steels, furnace atmospheres, quenching processes, SPC and computer technology. Data on over 135 additional irons and steels have been added to the previously-covered 280 alloys.

Download or read book Steel Forgings written by Edward G. Nisbett and published by ASTM International. This book was released on 1997 with total page 371 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprises 25 papers from the November 1996 symposium in New Orleans. The papers explore four subject areas: pressure vessel and nuclear forgings, general industrial forgings, test methods, and turbine and generator forgings. Specific paper topics include: new materials and forgings used for pressure

Download or read book Steel Forgings written by and published by ASTM International. This book was released on 1997 with total page 144 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Automotive Steels written by Radhakanta Rana and published by Woodhead Publishing. This book was released on 2016-11-26 with total page 481 pages. Available in PDF, EPUB and Kindle. Book excerpt: Automotive Steels: Design, Metallurgy, Processing and Applications explores the design, processing, metallurgy, and applications of automotive steels. While some sheet steels are produced routinely in high volume today, there have been significant advances in the use of steel in the automotive industry. This book presents these metallurgical and application aspects in a way that is not available in the current literature. The editors have assembled an international team of experts who discuss recent developments and future prospects for automotive steels, compiling essential reading for both academic and industrial metallurgists, automotive design engineers, and postgraduate students attending courses on the metallurgy of automotive materials. - Presents recent developments on the design, metallurgy, processing, and applications of automotive steels - Discusses automotive steels that are currently in the early stages of research, such as low-density and high modulus steels that are driving future development - Covers traditional steels, advanced high strength steels, elevated Mn steels and ferrous composite materials

Download or read book Hot Working Guide written by Y. V. R. K. Prasad and published by ASM International. This book was released on 1997-01-01 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: A unique source book with flow stress data for hot working, processing maps with metallurgical interpretation and optimum processing conditions for metals, alloys, intermetallics, and metal matrix composites. The use of this book replaces the expensive and time consuming trial and error methods in process design and product development.

Download or read book Steels for Large Solid propellant Rocket motor Cases written by Battelle Memorial Institute. Defense Metals Information Center and published by . This book was released on 1962 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Minimum Property Standards written by and published by . This book was released on 1979 with total page 576 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Vacuum Degassing in the Production of Premium quality Steels written by P. J. O'Reilly and published by . This book was released on 1964 with total page 138 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report gives the experiences of several steel producers and consumers with vacuum degassing as a melting practice in the manufacture of high-strength steels for critical applications. The parameters involved in determining the effects of melting practice on mechanical properties are outlined. Pertinent melting processes are described and evaluated qualitatively. In presenting the data, vacuum degassing is compared with other melting practices such as conventional air melting and consumable-electrode vacuum-arc remelting (CEVAR). Generally, there is a trend indicating that vacuum degassing is being used in some production applications instead of air-melted or CEVAR material. In terms of higher and more uniform transverse tensile properties and impact strength, longer fatigue life, and improved cleanliness, the CEVAR alloys were the best. Vacuum degassing by any of the various methods resulted in an improvement in properties of air-melted alloys. In some instances it appeared that the quality of CEVAR alloys could be approached when stream degassing or D-H (Dortmund-Horder) treatment was applied to air melts. Recommendations are given for additional investigations on the effects of melting practice on mechanical properties of premium-quality steels. (Author).

Download or read book The Michigan Technic written by and published by UM Libraries. This book was released on 1932 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book The Mechanical Properties of the 18 Per Cent Nickel Maraging Steels written by J. E. Campbell and published by . This book was released on 1964 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the combination of tensile properties and toughness that can be obtained with the maraging steels is higher than can be achieved with other steels by simple heat treatments, there is considerable interest in using the maraging steels for critical components such as rocket motor cases, pressure vessels, and aircraft forgings. This report includes information on the tensile, compressive, shear, bearing, dynamic modulus, impact, bend, fatigue, creep, and rupture properties of the 18 per cent nickel maraging steels and on the effect of temperature on these properties. Data for the properties of sheet, bar, and forgings, as well as data illustrating the effect of cold rolling, variation in the heat treatment, and elevated-temperature exposure also are presented. Data on the effect of specimen orientation, which are also included, indicate that the ductility and toughness of specimens designed to evaluate the properties in the short transverse direction are somewhat lower than in the other directions. The high strength and toughness that can be obtained in the 18 per cent nickel maraging steels make them attractive for certain critical applications that require these properties. The fabrication characteristics, weldability, and simple heat treatment are other advantages of these steels. (Author).

Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1957 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Semiaustenitic Precipitation hardenable Stainless Steels written by D. C. Ludwigson and published by . This book was released on 1961 with total page 186 pages. Available in PDF, EPUB and Kindle. Book excerpt: The semiaustenitic precipitation-hardenable stainless steels remain austenitic on cooling rom a solution heat treatment at about 1950 F. In this form they are readily fabricable. Subsequent treatment at about 1400 or at about 1725 F depletes the austenite of Cr and C to the extent that martensite forms on cooling to room temperature or -100 F, respectively. Final hardening is effected by tempering, or aging, at 750 to 1100 F. The semiaustenitic precipitation-hardenable stainless steels may be obtained as transformed at the mill by cold rolling. In this condition they lack the good formability of solution-heat-treated material. However, the fabricator need only temper them to obtain very high strengths. These steels have a combination of good formability, high strength, and excellent corrosion resistance that is not easily matched by other materials.

Download or read book Die Design Handbook written by David Alkire Smith and published by Society of Manufacturing Engineers. This book was released on 1990 with total page 957 pages. Available in PDF, EPUB and Kindle. Book excerpt: Whether you're involved in a highly specialized operation, or need comprehensive information on many types of die designs, this book is your best bet book on how to design dies. Hundreds of illustrations on proven designs are included, as well as hundreds of tables and equations to help you make quick calculations for allowances, pressures, forces and more.

Download or read book Aerospace Structural Metals Handbook written by and published by . This book was released on 1989 with total page 778 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Handbook of Valves and Actuators written by Brian Nesbitt and published by Elsevier. This book was released on 2011-04-19 with total page 571 pages. Available in PDF, EPUB and Kindle. Book excerpt: Industries that use pumps, seals and pipes will also use valves and actuators in their systems. This key reference provides anyone who designs, uses, specifies or maintains valves and valve systems with all of the critical design, specification, performance and operational information they need for the job in hand. Brian Nesbitt is a well-known consultant with a considerable publishing record. A lifetime of experience backs up the huge amount of practical detail in this volume.* Valves and actuators are widely used across industry and this dedicated reference provides all the information plant designers, specifiers or those involved with maintenance require* Practical approach backed up with technical detail and engineering know-how makes this the ideal single volume reference* Compares and contracts valve and actuator types to ensure the right equipment is chosen for the right application and properly maintained

Download or read book Structural Considerations in Developing Refractory Metal Alloys written by R. I. Jaffee and published by . This book was released on 1963 with total page 36 pages. Available in PDF, EPUB and Kindle. Book excerpt: Progress made in applying advanced techniques and structural concepts to the problem of strengthening the Group VI-A metals, Cr, Mo, and W, is examined. At low temperatures, T/Tm