Download or read book Fracture Toughness of Alloy 600 and EN82H Weld in Air and Water written by and published by . This book was released on 1999 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt: The fracture toughness of Alloy 600 and its weld, EN82H, was characterized in 54 C to 338 C air and hydrogenated water. Elastic-plastic J{sub IC} testing was performed due to the inherent high toughness of these materials. Alloy 600 exhibited excellent fracture toughness under all test conditions. While EN82H welds displayed excellent toughness in air and high temperature water, a dramatic toughness degradation occurred in water at temperatures below 149 C. Comparison of the cracking response in low temperature water with that for hydrogen-precharged specimens tested in air demonstrated that the loss in toughness is due to a hydrogen-induced intergranular cracking mechanism. At loading rates about approx. 1000 MPa (square root)m/h, the toughness in low temperature water is improved because there is insufficient time for hydrogen to embrittle grain boundaries. Electron fractographic examinations were performed to correlate macroscopic properties with key microstructural features and operative fracture mechanisms.
Download or read book FRACTURE BEHAVIOR OF ALLOY 600 ALLOY 690 EN82H WELDS AND EN52 WELDS IN WATER written by and published by . This book was released on 2000 with total page 41 pages. Available in PDF, EPUB and Kindle. Book excerpt: The cracking resistance of Alloy 600, Alloy 690 and their welds, EN82H and EN52, was characterized by conducting J{sub IC} rising load tests in air and hydrogenated water and cooldown testing in water under constant-displacement conditions. All test materials displayed excellent toughness in air and high temperature water, but Alloy 690 and the two welds were severely embrittled in low temperature water. In 54 C water with 150 cc H2/kg H2O, J{sub IC} values were reduced by 70% to 95%, relative to their air counterpart. The toughness degradation was associated with a fracture mechanism transition from microvoid coalescence to intergranular fracture. Comparison of the cracking response in water with that for hydrogen-precharged specimens tested in air demonstrated that susceptibility to low temperature crack propagation (LTCP) is due to hydrogen embrittlement of grain boundaries. The effects of water temperature, hydrogen content and loading rate on LTCP were studied. In addition, testing of specimens containing natural weld defects and as-machined notches was performed to determine if low temperature cracking can initiate at these features. Unlike the other materials, Alloy 600 is not susceptible to LTCP as the toughness in 54 C water remained high and a microvoid coalescence mechanism was operative in both air and water. Cooldown testing of EN82H welds under constant-displacement conditions was performed to determine if LTCP data from rising load J{sub IC}/K{sub Pmax} tests predict the onset of LTCP for other load paths. In these tests, bolt-loaded CT specimens were subjected to 288 C water for up to 1 week, cooled to 54 C and held in 54 C hydrogenated water for 1 week. This cycle was repeated up to 6 times. For two of the three welds tested, critical K{sub I} levels for LTCP under constant-displacement conditions were much higher than rising load K{sub Pmax} values. Bolt-loaded specimens from a third weld were found to exhibit LTCP at K{sub I} levels comparable to K{sub Pmax} values. Although work to date indicates that rising load tests either accurately or conservatively predict the critical conditions for LTCP under constant displacement conditions, the potential for LTCP at K{sub I} levels less than K{sub Pmax} has not been fully evaluated. Annealing at 1093 C reduces or eliminates LTCP susceptibility. The microstructure and mechanical properties for susceptible and nonsusceptible EN82H welds were characterized to identify the key material parameters responsible for LTCP in the as-welded condition. The key microstructural feature associated with LTCP appears to be fine Nb- and Ti-rich carbonitrides decorating grain boundaries. In addition, the higher yield strength for the as-fabricated weld also promotes LTCP because it increases stresses and local hydrogen concentrations ahead of a crack.
Download or read book Gaseous Hydrogen Embrittlement of Materials in Energy Technologies written by Richard P Gangloff and published by Elsevier. This book was released on 2012-01-16 with total page 864 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many modern energy systems are reliant on the production, transportation, storage, and use of gaseous hydrogen. The safety, durability, performance and economic operation of these systems is challenged by operating-cycle dependent degradation by hydrogen of otherwise high performance materials. This important two-volume work provides a comprehensive and authoritative overview of the latest research into managing hydrogen embrittlement in energy technologies.Volume 1 is divided into three parts, the first of which provides an overview of the hydrogen embrittlement problem in specific technologies including petrochemical refining, automotive hydrogen tanks, nuclear waste disposal and power systems, and H2 storage and distribution facilities. Part two then examines modern methods of characterization and analysis of hydrogen damage and part three focuses on the hydrogen degradation of various alloy classesWith its distinguished editors and international team of expert contributors, Volume 1 of Gaseous hydrogen embrittlement of materials in energy technologies is an invaluable reference tool for engineers, designers, materials scientists, and solid mechanicians working with safety-critical components fabricated from high performance materials required to operate in severe environments based on hydrogen. Impacted technologies include aerospace, petrochemical refining, gas transmission, power generation and transportation. - Summarises the wealth of recent research on understanding and dealing with the safety, durability, performance and economic operation of using gaseous hydrogen at high pressure - Reviews how hydrogen embrittlement affects particular sectors such as the petrochemicals, automotive and nuclear industries - Discusses how hydrogen embrittlement can be characterised and its effects on particular alloy classes
Download or read book Proceedings of the 15th International Conference on Environmental Degradation of Materials in Nuclear Power Systems Water Reactors written by Gabriell Ilevbare and published by Springer. This book was released on 2017-07-17 with total page 2354 pages. Available in PDF, EPUB and Kindle. Book excerpt: This 15th Edition of the International Conference on Materials Degradation in Light Water Reactors focuses on subject areas critical to the safe and efficient running of nuclear reactor systems through the exchange and discussion of reseach results as well as field operating and management experience.
Download or read book Ninth International Symposium on Environmental Degradation of Materials in Nuclear Power Systems written by Steve Bruemmer and published by John Wiley & Sons. This book was released on 2013-10-18 with total page 1776 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection presents an exchange of ideas among scientists and engineers about the economic and safety concerns surrounding environmentally induced materials problems which lead to nuclear power plant outages. Scientists and engineers concerned with the environmental degradation processes (corrosion, mechanical, and radiation effects) present their latest results on such topics as life extension/relicensing and materials problems associated with spent fuel storage and radioactive waste disposal. This collection will be of interest to utility engineers, reactor vendor engineers, plant architect engineers, researchers concerned with materials degradation, and consultants involved in design, construction, and operation of water reactors.
Download or read book Fracture Behavior of Nickel based Alloys in Water written by and published by . This book was released on 1999 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: The cracking resistance of Alloy 600, Alloy 690 and their welds, EN82H and EN52, was characterized by conducting J{sub IC} tests in air and hydrogenated water. All test materials displayed excellent toughness in air and high temperature water, but Alloy 690 and the two welds were severely embrittled in low temperature water. In 54 C water with 150 cc H2/kg H2O, J{sub IC} values were typically 70% to 95% lower than their air counterparts. The toughness degradation was associated with a fracture mechanism transition from microvoid coalescence to intergranular fracture. Comparison of the cracking response in water with that for hydrogen-precharged specimens tested in air demonstrated that susceptibility to low temperature cracking is due to hydrogen embrittlement of grain boundaries. The effects of water temperature, hydrogen content and loading rate on low temperature crack propagation were studied. In addition, testing of specimens containing natural weld defects and as-machined notches was performed to determine if low temperature cracking can initiate at these features. Unlike the other materials, Alloy 600 is not susceptible to low temperature cracking as the toughness in 54 C water remained high and a microvoid coalescence mechanism was operative in both air and water.
Download or read book Scientific Basis for Nuclear Waste Management written by and published by . This book was released on 2004 with total page 650 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture Toughness of Alloy 690 and EN52 Weld in Air and Water written by and published by . This book was released on 1999 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: The effect of low and high temperature water with high hydrogen on the fracture toughness of Alloy 690 and its weld, EN52, was characterized using elastic-plastic J{sub IC} methodology. While both materials display excellent fracture resistance in air and elevated temperature (>93 C) water, a dramatic degradation in toughness is observed in 54 C water. The loss of toughness is associated with a hydrogen-induced intergranular cracking mechanism where hydrogen is picked up from the water. Comparison of the cracking behavior in low temperature water with that for hydrogen-precharged specimens tested in air indicates that the critical local hydrogen content required to cause low temperature embrittlement is on the order of 120 to 160 ppm. Loading rate studies show that the cracking resistance is significantly improved at rates above ca. 1000 MPa(square root)m/h because there is insufficient time to produce grain boundary embrittlement. Electron fractographic examinations were performed to correlate cracking behavior with microstructural features and operative fracture mechanics.
Download or read book Proceedings of the 18th International Conference on Environmental Degradation of Materials in Nuclear Power Systems Water Reactors written by John H. Jackson and published by Springer. This book was released on 2018-12-20 with total page 2460 pages. Available in PDF, EPUB and Kindle. Book excerpt: This two-volume set represents a collection of papers presented at the 18th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors. The purpose of this conference series is to foster an exchange of ideas about problems and their remedies in water-cooled nuclear power plants of today and the future. Contributions cover problems facing nickel-based alloys, stainless steels, pressure vessel and piping steels, zirconium alloys, and other alloys in water environments of relevance. Components covered include pressure boundary components, reactor vessels and internals, steam generators, fuel cladding, irradiated components, fuel storage containers, and balance of plant components and systems.
Download or read book Superalloys 718 625 706 and Various Derivatives written by E. A. Loria and published by Minerals, Metals, & Materials Society. This book was released on 2001 with total page 776 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text comprises a collection of papers from the Fifth International Symposium on Superalloys 718, 625, 706 and Derivatives held in June, 2001 in Pittsburgh. This volume includes discussion on melting, solidification, casting, forming technology, thermal processing, and physical metallurgy.
Download or read book Chemical Abstracts written by and published by . This book was released on 2002 with total page 2726 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Pressure Vessel and Piping Codes and Standards 2001 written by Mahendra D. Rana and published by . This book was released on 2001 with total page 242 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Pressure Vessels and Piping Codes and Standards written by and published by . This book was released on 2004 with total page 426 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Service Experience Structural Integrity Severe Accidents and Erosion in Nuclear and Fossil Plants written by Steve R. Paterson and published by . This book was released on 1995 with total page 436 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the ASME Pressure Vessels and Piping Conference 2005 Codes and standards written by and published by American Society of Mechanical Engineers. This book was released on 2005 with total page 410 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Welding Metallurgy and Weldability of Nickel Base Alloys written by John C. Lippold and published by John Wiley & Sons. This book was released on 2011-09-20 with total page 370 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most up-to-date coverage of welding metallurgy aspects and weldability issues associated with Ni-base alloys Welding Metallurgy and Weldability of Nickel-Base Alloys describes the fundamental metallurgical principles that control the microstructure and properties of welded Ni-base alloys. It serves as a practical how-to guide that enables engineers to select the proper alloys, filler metals, heat treatments, and welding conditions to ensure that failures are avoided during fabrication and service. Chapter coverage includes: Alloying additions, phase diagrams, and phase stability Solid-solution strengthened Ni-base alloys Precipitation strengthened Ni-base alloys Oxide dispersion strengthened alloys and nickel aluminides Repair welding of Ni-base alloys Dissimilar welding Weldability testing High-chromium alloys used in nuclear power applications With its excellent balance between the fundamentals and practical problem solving, the book serves as an ideal reference for scientists, engineers, and technicians, as well as a textbook for undergraduate and graduate courses in welding metallurgy.
Download or read book Nuclear Corrosion Science and Engineering written by Damien Feron and published by Elsevier. This book was released on 2012-02-21 with total page 1073 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion of nuclear materials, i.e. the interaction between these materials and their environments, is a major issue for plant safety as well as for operation and economic competitiveness. Understanding these corrosion mechanisms, the systems and materials they affect, and the methods to accurately measure their incidence is of critical importance to the nuclear industry. Combining assessment techniques and analytical models into this understanding allows operators to predict the service life of corrosion-affected nuclear plant materials, and to apply the most appropriate maintenance and mitigation options to ensure safe long term operation.This book critically reviews the fundamental corrosion mechanisms that affect nuclear power plants and facilities. Initial sections introduce the complex field of nuclear corrosion science, with detailed chapters on the different types of both aqueous and non aqueous corrosion mechanisms and the nuclear materials susceptible to attack from them. This is complemented by reviews of monitoring and control methodologies, as well as modelling and lifetime prediction approaches. Given that corrosion is an applied science, the final sections review corrosion issues across the range of current and next-generation nuclear reactors, and across such nuclear applications as fuel reprocessing facilities, radioactive waste storage and geological disposal systems.With its distinguished editor and international team of expert contributors, Nuclear corrosion science and engineering is an invaluable reference for nuclear metallurgists, materials scientists and engineers, as well as nuclear facility operators, regulators and consultants, and researchers and academics in this field. - Comprehensively reviews the fundamental corrosion mechanisms that affect nuclear power plants and facilities - Chapters assess different types of both aqueous and non aqueous corrosion mechanisms and the nuclear materials susceptible to attack from them - Considers monitoring and control methodologies, as well as modelling and lifetime prediction approaches
