Download or read book Underbalanced Drilling Limits and Extremes written by Bill Rehm and published by Elsevier. This book was released on 2013-11-25 with total page 680 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present crude oil and natural gas reservoirs around the world have depleted conventional production levels. To continue enhancing productivity for the remaining mature reservoirs, drilling decision-makers could no longer rely on traditional balanced or overbalanced methods of drilling. Derived from conventional air drilling, underbalanced drilling is increasingly necessary to meet today’s energy and drilling needs. While more costly and extreme, underbalanced drilling can minimize pressure within the formation, increase drilling rate of penetration, reduce formation damage and lost circulation, making mature reservoirs once again viable and more productive. To further explain this essential drilling procedure, Bill Rehm, an experienced legend in drilling along with his co-editors, has compiled a handbook perfect for the drilling supervisor. Underbalanced Drilling: Limits and Extremes, written under the auspices of the IADC Technical Publications Committee, contain many great features and contributions including: Real case studies shared by major service companies to give the reader guidelines on what might happen in actual operations Questions and answers at the end of the chapters for upcoming engineers to test their knowledge Common procedures, typical and special equipment involved, and most importantly, the limits and challenges that still surround this technology

Download or read book Applied Gaseous Fluid Drilling Engineering written by Boyun Guo and published by Gulf Professional Publishing. This book was released on 2021-09-23 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: Applied Gaseous Fluid Drilling Engineering: Design and Field Case Studies provides an introduction on the benefits of using gaseous fluid drilling engineering. In addition, the book describes the multi-phase systems needed, along with discussions on stability control. Safety and economic considerations are also included, as well as key components of surface equipment needed and how to properly select equipment depending on the type of fluid system. Rounding out with proven case studies that demonstrate good practices and lessons from failures, this book delivers a practical tool for understanding the guidelines and mitigations needed to utilize this valuable process and technology. - Helps readers gain a framework of understanding regarding the basic processes, technology and equipment needed for gaseous fluid drilling operations - Highlights benefits and challenges using drilling flow charts, photos of relevant equipment, and table comparisons of available fluid systems - Presents multiple case studies involving successful and unsuccessful operations

Download or read book Reservoir Formation Damage written by Faruk Civan and published by Elsevier. This book was released on 2011-08-30 with total page 1135 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reservoir Formation Damage, Second edition is a comprehensive treatise of the theory and modeling of common formation damage problems and is an important guide for research and development, laboratory testing for diagnosis and effective treatment, and tailor-fit- design of optimal strategies for mitigation of reservoir formation damage. The new edition includes field case histories and simulated scenarios demonstrating the consequences of formation damage in petroleum reservoirsFaruk Civan, Ph.D., is an Alumni Chair Professor in the Mewbourne School of Petroleum and Geological Engineering at the University of Oklahoma in Norman. Dr. Civan has received numerous honors and awards, including five distinguished lectureship awards and the 2003 SPE Distinguished Achievement Award for Petroleum Engineering Faculty. - Petroleum engineers and managers get critical material on evaluation, prevention, and remediation of formation damage which can save or cost millions in profits from a mechanistic point of view - State-of-the-Art knowledge and valuable insights into the nature of processes and operational practices causing formation damage - Provides new strategies designed to minimize the impact of and avoid formation damage in petroleum reservoirs with the newest drilling, monitoring, and detection techniques

Download or read book Managed Pressure Drilling written by Bill Rehm and published by Elsevier. This book was released on 2013-12-18 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt: With extraction out of depleted wells more important than ever, this new and developing technology is literally changing drilling engineering for future generations. Never before published in book form, these cutting-edge technologies and the processes that surround them are explained in easy-tounderstand language, complete with worked examples, problems and solutions. This volume is invaluable as a textbook for both the engineering student and the veteran engineer who needs to keep up with changing technology.

Download or read book Petroleum Rock Mechanics written by Bernt S. Aadnoy and published by Gulf Professional Publishing. This book was released on 2019-06-15 with total page 461 pages. Available in PDF, EPUB and Kindle. Book excerpt: Petroleum Rock Mechanics: Drilling Operations and Well Design, Second Edition, keeps petroleum and drilling engineers centrally focused on the basic fundamentals surrounding geomechanics, while also keeping them up-to-speed on the latest issues and practical problems. Updated with new chapters on operations surrounding shale oil, shale gas, and hydraulic fracturing, and with new sections on in-situ stress, drilling design of optimal mud weight, and wellbore instability analysis, this book is an ideal resource. By creating a link between theory with practical problems, this updated edition continues to provide the most recent research and fundamentals critical to today's drilling operations. - Helps readers grasp the techniques needed to analyze and solve drilling challenges, in particular wellbore instability analysis - Teaches rock mechanic fundamentals and presents new concepts surrounding sand production and hydraulic fracturing operations - Includes new case studies and sample problems to practice

Download or read book Reservoir Formation Damage written by Faruk Civan and published by Gulf Professional Publishing. This book was released on 2023-04-07 with total page 1097 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reservoir Formation Damage: Fundamentals, Modeling, Assessment, and Mitigation, Fourth Edition gives engineers a structured layout to predict and improve productivity, providing strategies, recent developments and methods for more successful operations. Updated with many new chapters, including completion damage effects for fractured wells, flow assurance, and fluid damage effects, the book will help engineers better tackle today's assets. Additional new chapters include bacterial induced formation damage, new aspects of chemically induced formation damage, and new field application designs and cost assessments for measures and strategies. Additional procedures for unconventional reservoirs get the engineer up to date. Structured to progress through your career, Reservoir Formation Damage, Fourth Edition continues to deliver a trusted source for both petroleum and reservoir engineers. - Covers new applications through case studies and test questions - Bridges theory and practice, with detailed illustrations and a structured progression of chapter topics - Considers environmental aspects, with new content on water control, conformance and produced water reinjection

Download or read book Composition and Properties of Drilling and Completion Fluids written by Ryen Caenn and published by Gulf Professional Publishing. This book was released on 2011-09-29 with total page 721 pages. Available in PDF, EPUB and Kindle. Book excerpt: The petroleum industry in general has been dominated by engineers and production specialists. The upstream segment of the industry is dominated by drilling/completion engineers. Usually, neither of those disciplines have a great deal of training in the chemistry aspects of drilling and completing a well prior to its going on production. The chemistry of drilling fluids and completion fluids have a profound effect on the success of a well. For example, historically the drilling fluid costs to drill a well have averaged around 7% of the overall cost of the well, before completion. The successful delivery of up to 100% of that wellbore, in many cases may be attributable to the fluid used. Considered the "bible" of the industry, Composition and Properties of Drilling and Completion Fluids, first written by Walter Rogers in 1948, and updated on a regular basis thereafter, is a key tool to achieving successful delivery of the wellbore. In its Sixth Edition, Composition and Properties of Drilling and Completion Fluids has been updated and revised to incorporate new information on technology, economic, and political issues that have impacted the use of fluids to drill and complete oil and gas wells. With updated content on Completion Fluids and Reservoir Drilling Fluids, Health, Safety & Environment, Drilling Fluid Systems and Products, new fluid systems and additives from both chemical and engineering perspectives, Wellbore Stability, adding the new R&D on water-based muds, and with increased content on Equipment and Procedures for Evaluating Drilling Fluid Performance in light of the advent of digital technology and better manufacturing techniques, Composition and Properties of Drilling and Completion Fluids has been thoroughly updated to meet the drilling and completion engineer's needs. - Explains a myriad of new products and fluid systems - Cover the newest API/SI standards - New R&D on water-based muds - New emphases on Health, Safety & Environment - New Chapter on waste management and disposal

Download or read book Petroleum Engineer s Guide to Oil Field Chemicals and Fluids written by Johannes Fink and published by Gulf Professional Publishing. This book was released on 2011-05-13 with total page 809 pages. Available in PDF, EPUB and Kindle. Book excerpt: Petroleum Engineer's Guide to Oil Field Chemicals and Fluids is a comprehensive manual that provides end users with information about oil field chemicals, such as drilling muds, corrosion and scale inhibitors, gelling agents and bacterial control. This book is an extension and update of Oil Field Chemicals published in 2003, and it presents a compilation of materials from literature and patents, arranged according to applications and the way a typical job is practiced. The text is composed of 23 chapters that cover oil field chemicals arranged according to their use. Each chapter follows a uniform template, starting with a brief overview of the chemical followed by reviews, monomers, polymerization, and fabrication. The different aspects of application, including safety and environmental impacts, for each chemical are also discussed throughout the chapters. The text also includes handy indices for trade names, acronyms and chemicals. Petroleum, production, drilling, completion, and operations engineers and managers will find this book invaluable for project management and production. Non-experts and students in petroleum engineering will also find this reference useful. - Chemicals are ordered by use including drilling muds, corrosion inhibitors, and bacteria control - Includes cutting edge chemicals and polymers such as water soluble polymers and viscosity control - Handy index of chemical substances as well as a general chemical index

Download or read book Sand Control in Well Construction and Operation written by Davorin Matanovic and published by Springer Science & Business Media. This book was released on 2012-02-21 with total page 205 pages. Available in PDF, EPUB and Kindle. Book excerpt: Produced sand causes a lot of problems. From that reasons sand production must be monitored and kept within acceptable limits. Sand control problems in wells result from improper completion techniques or changes in reservoir properties. The idea is to provide support to the formation to prevent movement under stresses resulting from fluid flow from reservoir to well bore. That means that sand control often result with reduced well production. Control of sand production is achieved by: reducing drag forces (the cheapest and most effective method), mechanical sand bridging (screens, gravel packs) and increasing of formation strength (chemical consolidation). For open hole completions or with un-cemented slotted liners/screens sand failure will occur and must be predicted. Main problem is plugging. To combat well failures due to plugging and sand breakthrough Water-Packing or Shunt-Packing are used.

Download or read book Air and Gas Drilling Manual written by William C. Lyons and published by Elsevier. This book was released on 2009-01-15 with total page 777 pages. Available in PDF, EPUB and Kindle. Book excerpt: The third edition of Air and Gas Drilling Manual describes the basic simulation models for drilling deep wells with air or gas drilling fluids, gasified two-phase drilling fluids, and stable foam drilling fluids. The models are the basis for the development of a systematic method for planning under balanced deep well drilling operations and for monitoring the drilling operation as well as construction project advances. Air and Gas Drilling Manual discusses both oil and natural gas industry applications, and geotechnical (water well, environmental, mining) industry applications. Important well construction and completion issues are discussed for all applications. The engineering analyses techniques are used to develop pre-operations planning methods, troubleshooting operations monitoring techniques and overall operations risk analysis. The essential objective of the book is drilling and well construction cost management control. The book is in both SI and British Imperial units. - Master the air and gas drilling techniques in construction and development of water wells, monitoring wells, geotechnical boreholes, mining operations boreholes and more - 30% of all wells drilled use gas and air, according to the U.S. Department of Energy estimates - Contains basic simulation equations with examples for direct and reverse circulation drilling models and examples for air and gas, gasified fluids, and stable foam drilling models

Download or read book Applied Drilling Circulation Systems written by Boyun Guo and published by Gulf Professional Publishing. This book was released on 2011-04-21 with total page 273 pages. Available in PDF, EPUB and Kindle. Book excerpt: Used to clean the borehole, stabilize rock, control pressures, or enhance drilling rates, drilling fluids and their circulation systems are used in all phases of a drilling operation. These systems are highly dynamic and complicated to model until now. Written by an author with over 25 years of experience, Applied Drilling Circulation Systems: Hydraulics, Calculations and Models provide users with the necessary analytical/numerical models to handle problems associated with the design and optimization of cost-effective drilling circulation systems. The only book which combines system modeling, design, and equipment, Applied Drilling Circulation Systems: Hydraulics, Calculations and Models provides a clear and rigorous exposition of traditional and non-traditional circulation systems and equipment followed by self contained chapters concerning system modelling applications. Theories are illustrated by case studies based on the author's real life experience. The book is accompanied by a website which permits readers to construct, validate, and run models employing Newtonian fluids, Bingham Plastic fluids, Power Law fluids, and aerated fluids principles. This combination book and website arrangement will prove particularly useful to drilling and production engineers who need to plan operations including pipe-tripping, running-in casing, and cementing. - In-depth coverage of both on- and offshore drilling hydraulics. - Methods for optimizing both on- and offshore drilling hydraulics. - Contains problems and solutions based on years of experience.

Download or read book Lost Circulation written by Alexandre Lavrov and published by Gulf Professional Publishing. This book was released on 2016-03-16 with total page 266 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lost Circulation: Mechanisms and Solutions provides the latest information on a long-existing problem for drilling and cementing engineers that can cause improper drilling conditions, safety risks, and annual losses of millions of wasted dollars for oil and gas companies. While several conferences have convened on the topic, this book is the first reliable reference to provide a well-rounded, unbiased approach on the fundamental causes of lost circulation, how to diagnose it in the well, and how to treat and prevent it in future well planning operations. As today's drilling operations become more complex, and include situations such as sub-salt formations, deepwater wells with losses caused by cooling, and more depleted reservoirs with reduced in-situ stresses, this book provides critical content on the current state of the industry that includes a breakdown of basics on stresses and fractures and how drilling fluids work in the wellbore. The book then covers the more practical issues caused by induced fractures, such as how to understand where the losses are occurring and how to use proven preventative measures such as wellbore strengthening and the effect of base fluid on lost circulation performance. Supported by realistic case studies, this book separates the many myths from the known facts, equipping today's drilling and cementing engineer with a go-to solution for every day well challenges. - Understand the processes, challenges and solutions involved in lost circulation, a critical problem in drilling - Gain a balance between fundamental understanding and practical application through real-world case studies - Succeed in solving lost circulation in today's operations such as wells involving casing drilling, deepwater, and managed pressure drilling

Download or read book Formation Damage Caused by Oil Well Drilling Fluids written by Mahmoud Abdou and published by Lulu.com. This book was released on 2014-07-14 with total page 521 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book investigates the limits of formation damage encountered with the various types of drilling fluids components. Remedial work was performed to restore the oil bearing formation characteristics. The objective of this book can be summarized in the following points: 1. Evaluation of various reservoir rocks towards the impact of the formation damage, caused by various types of drilling fluids, on the oil and / or gas productivity. 2. Delineate the pore channels blocking by the fine particles which may either caused by drilling fluids directly or released by filtrate invasion from the pore walls. 3. Minimize the formation damage using different treatment methods to improve the properties of formation productivity.

Download or read book Petroleum Engineering Handbook written by Larry W. Lake and published by . This book was released on 2006 with total page 930 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Petroleum Engineering Handbook has long been recognized as a valuable comprehensive reference book that offers practical day-to-day applications for students and experienced engineering professionals alike. Available now in 7 Volumes, Volume 1 covers General Engineering topics including chapters on mathematics, fluid properties (fluid sampling techniques; properties and correlations of oil, gas, condensate, and water; hydrocarbon phase behavior and phase diagrams for hydrocarbon systems; the phase behavior of water/hydrocarbon systems; and the properties of waxes, asphaltenes, and crude oil emulsions), rock properties (bulk rock properties, permeability, relative permeability, and capillary pressure), the economic and regulatory environment, and the role of fossil energy in the 21st century energy mix.

Download or read book IADC Drilling Manual written by IADC Staff and published by . This book was released on 2014-12-01 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The IADC Drilling Manual, 12th edition, is the definitive manual for drilling operations, training, maintenance and troubleshooting. The two-volume, 26-chapter reference guide covers all aspects of drilling, with chapters on types of drilling rigs, automation, drill bits, casing and tubing, casing while drilling, cementing, chains and sprockets, directional drilling, downhole tools, drill string, drilling fluid processing, drilling fluids, hydraulics, drilling practices, floating drilling equipment and operations, high-pressure drilling hoses, lubrication, managed pressure drilling and related practices, power generation and distribution, pumps, rotating and pipehandling equipment, special operations, structures and land rig mobilization, well control equipment and procedures, and wire rope. A comprehensive glossary of drilling terms is also included. More than 900 color and black-and-white illustrations, 600 tables and thirteen videos. 1,158 pages. Copyright © IADC. All rights reserved.

Download or read book Formation Damage during Improved Oil Recovery written by Bin Yuan and published by Gulf Professional Publishing. This book was released on 2018-05-31 with total page 678 pages. Available in PDF, EPUB and Kindle. Book excerpt: Formation Damage during Improved Oil Recovery: Fundamentals and Applications bridges the gap between theoretical knowledge and field practice by presenting information on formation damage issues that arise during enhanced oil recovery. Multi-contributed technical chapters include sections on modeling and simulation, lab experiments, field case studies, and newly proposed technologies and methods that are related to formation damage during secondary and tertiary recovery processes in both conventional and unconventional reservoirs. Focusing on both the fundamental theories related to EOR and formation damage, this reference helps engineers formulate integrated and systematic designs for applying EOR processes while also considering formation damage issues. - Presents the first complete reference addressing formation damage as a result of enhanced oil recovery - Provides the mechanisms for formation damage issues that are coupled with EOR - Suggests appropriate preventative actions or responses - Delivers a structured approach on how to understand the fundamental theories, practical challenges and solutions

Download or read book Standard Handbook of Petroleum and Natural Gas Engineering written by William Lyons and published by Gulf Professional Publishing. This book was released on 2015-12-08 with total page 1823 pages. Available in PDF, EPUB and Kindle. Book excerpt: Standard Handbook of Petroleum and Natural Gas Engineering, Third Edition, provides you with the best, state-of-the-art coverage for every aspect of petroleum and natural gas engineering. With thousands of illustrations and 1,600 information-packed pages, this handbook is a handy and valuable reference. Written by dozens of leading industry experts and academics, the book provides the best, most comprehensive source of petroleum engineering information available. Now in an easy-to-use single volume format, this classic is one of the true "must haves" in any petroleum or natural gas engineer's library. A classic for over 65 years, this book is the most comprehensive source for the newest developments, advances, and procedures in the oil and gas industry. New to this edition are materials covering everything from drilling and production to the economics of the oil patch. Updated sections include: underbalanced drilling; integrated reservoir management; and environmental health and safety. The sections on natural gas have been updated with new sections on natural gas liquefaction processing, natural gas distribution, and transport. Additionally there are updated and new sections on offshore equipment and operations, subsea connection systems, production control systems, and subsea control systems. Standard Handbook of Petroleum and Natural Gas Engineering, Third Edition, is a one-stop training tool for any new petroleum engineer or veteran looking for a daily practical reference. - Presents new and updated sections in drilling and production - Covers all calculations, tables, and equations for every day petroleum engineers - Features new sections on today's unconventional resources and reservoirs