Download or read book Fittings Axially Swaged Tube with Flareless Separable Fluid System 5080 Psi 35 000 KPa Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged titanium tube fittings on titanium tubing with flareless separable fitting for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35,000 kPa) maximum and an operating temperature range of -65 to +275 °F (-54 to +135 °C). This specification was prepared to provide the performance requirements for axially swaged, field attachable, 5080 psi, tube fittings.

Download or read book Fittings Axially Swaged Tube with Flareless Separable Fluid System for Operating Pressures Up to and Including 5080 Psi 35 000 KPa Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2009 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged titanium tube fittings on titanium and CRES tubing with flareless separable fitting for use in hydraulic supply and return aerospace fluid systems up to a maximum operating pressure of 5080 psig (35 000 kPa) and a maximum operating temperature range of -65 to +275 °F (-54 to +135 °C).This specification covers a common 5080 psi pressure titanium fitting that may be used for a range of operating pressures up to 5080 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5959. The fitting operating pressure is based on the fitting thread pitch. Extra fine pitch for 5080 psi operating pressure and fine pitch for operating pressures 3000 psi and less. Table 12 shows applicable fitting number and tubing materials and operating pressures. Add performance requirements for additional tube materials, tube thicknesses and pressures.

Download or read book Fittings Axially Swaged Tube with Flareless Separable Fluid System for Operating Pressures Up to and Including 5080 Psi 35000 KPa Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for axially swaged titanium fittings on titanium, CRES, and aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems up to operating pressure of 5080 psig (35000 kPa) maximum. The operating temperature range for titanium tubing and CRES tubing is 65 to +275 °F (54 to +135 °C) and the operating temperature range for aluminum return system tubing is 65 to +225 °F (54 to +107 °C).This specification covers a common 5080 psi pressure titanium fitting that may be used for a range of operating pressures up to 5080 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5959. The flareless fitting operating pressure is based on the fitting thread pitch. Extra fine pitch is used for 5080 psi operating pressure and fine pitch for operating pressures 3000 psi and less. Table 14 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Add performance requirements for aluminum tubing, class designation for tubing, update and correct existing text and figures.

Download or read book Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 Psi 10 340 KPa Maximum Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2011 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged aluminum tube fittings on aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems including pneumatic, coolants, and fire extinguishers up to a maximum operating pressure of 1500 psig (10 340 kPa) and a maximum operating temperature range of 65 to +225 °F (54 to +107 °C).This specification covers a common aluminum fitting that may be used for a range of operating pressures up to 1500 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS6124. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. This specification is being prepared to provide the performance requirements for aluminum axially swaged, field attachable, 1500 psi, tube fittings.

Download or read book Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 Psi 10340 KPa Maximum Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2016 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged aluminum tube fittings on aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems including pneumatic, coolants, and fire extinguishers up to a maximum operating pressure of 1500 psig (10340 kPa) and a maximum operating temperature range of -65 to +225 °F (-54 to +107 °C).This specification covers a common aluminum fitting that may be used for a range of operating pressures up to 1500 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS6124. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Change operating pressure requirements of size 24 from 500 to 600 psi (including proof and burst pressures), add vibration curves requirements to Tables 10 and 11 for size 24, add the new configuration part number AS6323 to Table 12, and add size 24 dimensions to some of the standards configurations.

Download or read book Fittings Tube Fluid System 3000 Psig 21 000 KPa Rated Pressure Externally Swaged Specification For written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged tube-fitting assemblies used in aircraft fluid systems in the following pressure classes: B (1500 psi or 10 500 kPa), and D (3000 psi or 21 000 kPa), and in temperature types I (65 to 160 °F or 55 to 70 °C), and II (65 to 275 °F or 55 to 135 °C) of AS2001.This specification covers a common Cres, titanium, and aluminum fittings that may be used for a range of operating pressures up to 3000 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordance with AS5902. Table 10 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. Complete update of the procurement specification to prepare for QPL listing of part standards listed in Table 10 including corrections of material specification numbers, tube materials, wall thicknesses in Table 7, description of back-up seal, and updating quality conformance plans.

Download or read book Aerospace Series Tube Fittings for Fluid Systems 5 080 Psi 35 000 KPa Qualification Specification written by British Standards Institute Staff and published by . This book was released on 1915-09-30 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: FLUID EQUIPMENT COMPONENTS, AIRCRAFT COMPONENTS, FLUID EQUIPMENT, PIPE FITTINGS, HYDRAULIC EQUIPMENT, PERFORMANCE, INSPECTION, APPROVAL TESTING, QUALITY CONTROL, SPECIMEN PREPARATION, MECHANICAL TESTING, AIR TRANSPORT ENGINEERING, DESIGN, PRODUCTION, QUALIFICATION APPROVAL, QUALITY ASSURANCE

Download or read book FITTING ASSEMBLY UNION AXIALLY SWAGED HYDRAULIC 5080 PSI written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2012 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: REVISED FOR DEFINITION CORRECTION OF DIMENSION A1 (FITTING BODY LENGTH) BY ADDING FIGURE 2 FOR CLARIFICATION, REVISE NOTES 7 & 13. ADD LETTER CODE "B" FOR FITTING ASSEMBLY WITH BLUE ANODIZED RING AND NOTE 16 AS AN OPTION FOR FUTURE REPLACEMENT OF CURRENT BLUE CODE COLORING, AND ADD AS6449 AS A NEW LUBRICANT TYPE. /1/MATERIALS:CODE LETTER "T" RINGS -AMS4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS4928 TITANIUM ALLOY 6.0AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT. BODY -AMS4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED 2FINISH: TITANIUM - NONE /3/COATINGS/LUBRICANTS /16/: aNO SUFFIX CODE LETTER (1)RINGS - THE OUTER SURFACE SHALL HAVE A .125 INCH MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. PTFE COATING OR PAINT SHALL BE RESISTANT TO AS1241 FLUID WHEN USED. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958. (2)BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. bSUFFIX CODE LETTER A (1)RINGS - NO BLUE PTFE COATING OR PAINT. THE WORD "BLUE" SHALL BE MARKED ON THE RING TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958. (2)BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. cSUFFIX CODE LETTER B (1)RINGS - PARTIALLY (.125 INCH MINIMUM WIDTH) OR COMPLETELY ANODIZED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958. (2)BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT, MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID. /4/PROCUREMENT SPECIFICATION: AS5958 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LISTING FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE www.eAuditNet.com FOR CURRENT QPL ON-LINE. 5DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. /7/FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. THE AFTER SWAGE ACCEPTABILITY LIMIT DIMENSION "Z" FOR EACH PORT SIZE IS DEFINED IN AS5959. 8SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. 9DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. aDIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED bDIMENSIONAL TOLERANCES SHALL BE ±.005 INCHES UNLESS OTHERWISE SPECIFIED cANGULAR TOLERANCES SHALL BE ±.50 DEGREES UNLESS OTHERWISE SPECIFIED dBREAK ALL EDGES .003 TO .010 INCHES UNLESS OTHERWISE SPECIFIED 10INTERPRETATION OF DRAWING PER ARP4296. /11/THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /12/FOR JUMP SIZE FITTINGS, A TRANSITION DIAMETER WILL OCCUR IN THIS AREA. /13/DIMENSION A IS THE FITTING ASSEMBLY LENGTH PRIOR TO SWAGE AND A1 IS THE FITTING BODY LENGTH BEFORE SWAGE. 14A CHANGE BAR ( %7c ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. /15/EXAMPLE OF PART NUMBER: /16/UNPAINTED RINGS "CODE A" WERE NEEDED TO PREVENT COATING/PAINT DEBRIS OF RINGS "NO CODE" IN CONTAMINATION SENSITIVE SYSTEMS. NO CODE LETTER AND CODE LETTER "A" PARTS ARE NOT RECOMMENDED FOR PROCUREMENT AFTER 03/31/2014 AND SHOULD BE REPLACED BY ANODIZED PARTS WITH CODE LETTER "B".

Download or read book Aerospace Separable Tube Fittings for Fluid Systems for 24 0D Cones for Pressures Up to 3 000 Psi Or 21 000 KPa Procurement Specification Inch metric written by British Standards Institute Staff and published by . This book was released on 1914-11-30 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aircraft components, Hydraulic equipment, Fluid equipment components, Fluid equipment, Pipe fittings, Threads, Defects, Surface defects, Pressure, Grades (quality), Performance, Dimensions, Angles (geometry), Colour codes, Marking, Finishes, Classification systems, Test pressure, Bend testing, Leak tests, Stress corrosion, Corrosion tests, Mechanical testing, Pressure testing, Sampling methods, Quality assurance, Inspection, Approval testing, Quality control, Statistical quality control, Packaging, Test specimens

Download or read book Aerospace Separable Tube Fittings for Fluid Systems for 24 0D Cones for Pressures Up to 3000 PSI Or 21000 KPa Procurement Specification Inch Metric written by British Standards Institute Staff and published by . This book was released on 2007-05-31 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aircraft components, Hydraulic equipment, Fluid equipment components, Fluid equipment, Pipe fittings, Threads, Defects, Surface defects, Pressure, Grades (quality), Performance, Dimensions, Angles (geometry), Colour codes, Marking, Finishes, Classification systems, Test pressure, Bend testing, Leak tests, Stress corrosion, Corrosion tests, Mechanical testing, Pressure testing, Sampling methods, Quality assurance, Inspection, Approval testing, Quality control, Statistical quality control, Packaging, Test specimens

Download or read book Fittings Tube Fluid Systems Separable Beam Seal 3000 4000 Psi General Specification For Supplement 1 written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification. AS85421SUP1 has been reaffirmed to comply with the SAE five-year review policy.

Download or read book Fittings Tube Fluid System 3000 4000 Psig Rated Pressure Externally Swaged Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2004 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for externally swaged tube fittings for use in hydraulic and other aerospace fluid systems in temperature range of -65 to 275 °F.

Download or read book TUBE FITTINGS FLUID SYSTEMS SEPARABLE GENERAL SPECIFICATION FOR written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 1981 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This document establishes the basic performance and quality criteria for screw-together tube fitting assemblies and port connectors used in aircraft fluid systems.

Download or read book Fittings Weld Fluid Connection 35 000 KPa Metric written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2015 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Metric Aerospace Standard (AS) establishes the requirements for weld fluid connection fittings and rings to be orbital arc welded to tubing for use in metric aircraft fluid systems at a maximum operating pressure of 35,000 kPa. MA4510 has been reaffirmed to comply with the SAE five-year review policy.

Download or read book Fitting Plug in Union Ring Locked 24 Cone Fluid Connection 5080 Psi Specification for written by G-3C, AS-EN Harmonization Task Group and published by . This book was released on 2006 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Aerospace Standard (AS) establishes the requirements for 24° cone AS5827 or EN 6123 flareless Ring locked fitting assemblies per AS5550 and AS5865, for use in aircraft fluid systems at nominal operating pressure of 5080 psi maximum and operating temperature range of -65 to +275 °F.The general requirements shall be for, but not limited to, commercial aircraft hydraulic components per AS4941, using port configuration as specified in AS5551. This specification covers requirements for qualification testing and procurement of flareless port fittings for 5000 psi hydraulic components.

Download or read book Fittings Tube Fluid Systems Separable Beam Seal 3000 4000 Psi General Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2021 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This specification covers the design requirements and test procedures for separable beam seal fittings which includes end fittings (see 2.3.4), fitting bodies (see 2.3.7), and boss fittings (see 2.3.2) for use in aerospace fluid systems. Design requirements are for class 3000 in corrosion resistant steel (15-5 PH, 17-4 PH CRES) only and for class 4000 in titanium alloy (Ti) and corrosion and heat-resistant steel (nickel alloy 718 CRES) only. Definition of fittings and related terms are defined in 2.3. Corrected error to sample numbers in burst test (4.6.3); modified periodic control testing procedures/tests (4.4.3); clarified flexure Tables 2A, 2B, and 2C; and added new tubing material options to Table 1.

Download or read book Fittings Tube Fluid Systems Separable High Pressure Beam Seal 5000 8000 Psi General Specification for written by G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This specification covers the design requirements and test procedures for separable beam seal fittings which include end fittings (see 2.4.2), connectors (see 2.4.3), and boss fittings for use in aerospace fluid systems. Design requirements are for Class 5000 and 8000 in titanium, and corrosion resistant steel (CRES). Definition of fittings and related terms are defined in 2.4. Modified periodic control testing procedures/tests (4.4.3); clarified flexure Tables 2A, 2B, and 2C; and added new tubing material options to Table 1.