Download or read book Fabrication and Test of a Fluidic Fuel Control and Bleed Air Load Control System for Gas Turbine Engines written by T. S. Thurston and published by . This book was released on 1977 with total page 41 pages. Available in PDF, EPUB and Kindle. Book excerpt: This program has produced a production fluidic fuel-control and bleed-air-load-control system which consists of a fuel control, a load valve, and a temperature sensor. Three sets of hardware were produced for use in a follow-on program. This hardware will be subjected to acceptance tests on the AiResearch Model GTCP85-180 gas turbine engine. The production system improved the steady-state performance over that demonstrated on the prototype control produced under the previous program. The fluidic circuits were designed to perform within specification limits when operated at altitude as well as high and low temperature conditions. Designs and drawings were modified wherever necessary to facilitate production. The system underwent engine and fuel bench testing to confirm design improvement and performance. As part of this testing, a 50-hour endurance bench test of the fuel control was performed. This test, as well as the engine tests conducted, identified minor problems with the fuel metering valve and the speed sensor which were easily corrected. The appropriate design changes were incorporated into the production configuration. The production fluidic fuel-control and bleed-air-load-control system performed satisfactorily, meeting the program and engine requirements and is therefore recommended for follow-on program testing. (Author).
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1987 with total page 1126 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.
Download or read book Fluidics Feedback written by and published by . This book was released on 1976 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book NASA SP written by and published by . This book was released on 1992 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Aeronautical Engineering written by and published by . This book was released on 1979 with total page 708 pages. Available in PDF, EPUB and Kindle. Book excerpt: A selection of annotated references to unclassified reports and journal articles that were introduced into the NASA scientific and technical information system and announced in Scientific and technical aerospace reports (STAR) and International aerospace abstracts (IAA).
Download or read book Government Reports Announcements Index written by and published by . This book was released on 1981 with total page 670 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Government Reports Annual Index written by and published by . This book was released on 1978 with total page 1610 pages. Available in PDF, EPUB and Kindle. Book excerpt: Sections 1-2. Keyword Index.--Section 3. Personal author index.--Section 4. Corporate author index.-- Section 5. Contract/grant number index, NTIS order/report number index 1-E.--Section 6. NTIS order/report number index F-Z.
Download or read book NASA Contributions to Fluidic Systems written by Terry M. Weathers and published by . This book was released on 1972 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt: A state-of-the art review of fluidic technology is presented. It is oriented towards systems applications rather than theory or design. It draws heavily upon work performed or sponsored by NASA in support of the space program and aeronautical research and development (R&D). Applications are emphasized in this survey because it is hoped that the examples described and the criteria presented for evaluating the suitability of fluidics to new applications will be of value to potential users of fluidic systems. This survey of the fluidics industry suggests some of the means whereby a company may use a fluidic system effectively either to manufacture a product or as part of the end product.
Download or read book Catalog of American National Standards written by American National Standards Institute and published by . This book was released on 1995 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the Intersociety Energy Conversion Engineering Conference written by and published by . This book was released on 1976 with total page 1006 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Flow and Combustion Control 2021 written by Rudibert King and published by Springer Nature. This book was released on 2021-11-12 with total page 359 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book reports on the latest theoretical and experimental findings in the field of active flow and combustion control, in the context of energy conversion for power and propulsion systems. It covers new developments in actuator technology and sensing, robust and optimal open- and closed-loop control, model reduction for control purposes, and unsteady turbine cooling and performance, among other relevant topics. Gathering contributions to the Active Flow and Combustion Control (AFCC 2021), held virtually on September 28-29, 2021, from the Technische Universität Berlin, Germany, this book describes research that has been carried out within, and supported by, the collaborative research center SFB 1029 on “Substantial efficiency increase in gas turbines through direct use of coupled unsteady combustion and flow dynamics”, and funded by the German Research Foundation (DFG). It highlights theoretical and practical aspects, and corresponding solutions, that are important for the development of future energy conversion systems, thus offering a timely guide for researchers and practitioners in the field of aeronautics, turbomachinery, control and combustion.
Download or read book Jane s All the World s Aircraft written by and published by . This book was released on 2001 with total page 928 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Active Flow and Combustion Control 2018 written by Rudibert King and published by Springer. This book was released on 2018-09-03 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book reports on the latest theoretical and experimental findings in the field of active flow and combustion control. It covers new developments in actuator technology and sensing, in robust and optimal open- and closed-loop control, as well as in model reduction for control, constant volume combustion and dynamic impingement cooling. The chapters reports oncutting-edge contributions presented during the fourth edition of the Active Flow and Combustion Control conference, held in September 19 to 21, 2018 at the Technische Universität Berlin, in Germany. This conference, as well as the research presented in the book, have been supported by the collaborative research center SFB 1029 on “Substantial efficiency increase in gas turbines through direct use of coupled unsteady combustion and flow dynamics”, funded by the DFG (German Research Foundation). It offers a timely guide for researchers and practitioners in the field of aeronautics, turbomachinery, control and combustion.
Download or read book 1989 1990 Catalog of American National Standards written by American National Standards Institute and published by . This book was released on 1989 with total page 204 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advanced Fluidic Controls for Integrated Propulsion Systems Part II Materials and Fabrication Techniques for High Temperature Turbine Engine Controls written by Kenneth E. Solie and published by . This book was released on 1968 with total page 105 pages. Available in PDF, EPUB and Kindle. Book excerpt: An investigation of materials and fabrication techniques for fluidic components used in fluidic fuel control systems for advanced propulsion systems was conducted. The program consisted of: (1) materials selection, (2) materials evaluation and (3) fabrication techniques suitable for the usable materials. A literature survey was made to select materials that could be used for fluidic components that must operate at various temperature ranges from 500 F to 3000 F. These candidate materials were evaluated under simulated operating conditions to assess their comparative behavior and ability to withstand the anticipated environment. Several methods of fabricating the selected materials, which ranged from aluminum to ceramics, were investigated. These techniques included standard machining practices, engraving, stamping, casting, etching-diffusion-bonding, electroforming, flame spraying, and several powder metallurgy processes. For use at temperatures below 800 F aluminum appears to be the best material. Precision engraving can be used for fabrication of small numbers of these devices, but etching-diffusion-bonding or powder metallurgy with EDM cleanup is better for high volume. Nickel devices fabricated by electroforming are best for temperatures below 1200 F. For temperatures between 1000 F and 1500 F, 309 stainless steel, fabricated by etching-diffusion-bonding should be used. Either Inconel 702 or Chrome 30 are good between 1500 F and 1800 F. Above 1800 F up to 3000 F KT silicon carbide was the only material investigated capable of prolonged life and capable of withstanding thermal shock. (Author).
Download or read book Thomas Register written by and published by . This book was released on 2004 with total page 2062 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fluidics written by James W. Joyce and published by . This book was released on 1979 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:
