Download or read book Experimental Study of Lean Pre mixed and Pre vaporised Turbulent Spray Combustion written by Y. Michou and published by . This book was released on 1999 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Turbulent Premixed Flames written by Nedunchezhian Swaminathan and published by Cambridge University Press. This book was released on 2011-04-25 with total page 447 pages. Available in PDF, EPUB and Kindle. Book excerpt: A work on turbulent premixed combustion is important because of increased concern about the environmental impact of combustion and the search for new combustion concepts and technologies. An improved understanding of lean fuel turbulent premixed flames must play a central role in the fundamental science of these new concepts. Lean premixed flames have the potential to offer ultra-low emission levels, but they are notoriously susceptible to combustion oscillations. Thus, sophisticated control measures are inevitably required. The editors' intent is to set out the modeling aspects in the field of turbulent premixed combustion. Good progress has been made on this topic, and this cohesive volume contains contributions from international experts on various subtopics of the lean premixed flame problem.
Download or read book Experimental Study of Premixed Lean Combustion in Opposing Jets written by Li Qiang Wang and published by . This book was released on 1994 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fundamentals of Premixed Turbulent Combustion written by Andrei Lipatnikov and published by CRC Press. This book was released on 2012-10-24 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt: Lean burning of premixed gases is considered to be a promising combustion technology for future clean and highly efficient gas turbine combustors. Yet researchers face several challenges in dealing with premixed turbulent combustion, from its nonlinear multiscale nature and the impact of local phenomena to the multitude of competing models. Filling
Download or read book Droplets and Sprays written by Saptarshi Basu and published by Springer. This book was released on 2017-12-11 with total page 433 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on droplets and sprays relevant to combustion and propulsion applications. The book includes fundamental studies on the heating, evaporation and combustion of individual droplets and basic mechanisms of spray formation. The contents also extend to the latest analytical, numerical and experimental techniques for investigating the behavior of sprays in devices like combustion engines and gas turbines. In addition, the book explores several emerging areas like interactions between sprays and flames and the dynamic characteristics of spray combustion systems on the fundamental side, as well as the development of novel fuel injectors for specific devices on the application side. Given its breadth of coverage, the book will benefit researchers and professionals alike.
Download or read book Experimental Investigation of the Dynamics and Structure of Lean premixed Turbulent Combustion written by and published by . This book was released on 2003 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: PhD.
Download or read book Experimental Study of Turbulent Premixed Combustion in V shaped Flames written by Sina Kheirkhah and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Characteristics of turbulent premixed flames were investigated experimentally. The investigations were performed using Mie scattering, Particle Image Velocimetry, Rayleigh scattering, and broad-band luminosity imaging techniques. Methane-air flames associated with a relatively wide range of turbulence intensities, fuel-air equivalence ratios, and mean bulk flow velocities were investigated. For a relatively moderate value of turbulence intensity, a new concept is introduced and utilized to provide a detailed description associated with interaction of turbulent flow and flame front. The concept pertains to reactants velocity estimated at the vicinity of the flame front and is referred to as the edge velocity. Specifically, it is shown that fluctuations of the flame front position are induced by fluctuations of the edge velocity. For a relatively wide range of turbulence intensity, several characteristics of turbulent premixed flames, namely, front topology, brush thickness, surface density, and consumption speeds are investigated. For the first time, several flame front structures are identified and studied. It is shown that, due to formation of these front structures, the regime of turbulent premixed combustion transitions from the regime of counter-gradient diffusion to that of the gradient diffusion. In addition to these, a comprehensive study is performed to investigate influence of flame configuration on several flame front characteristics. It is obtained that, although changing the flame configuration influences several flame characteristics, the trends associated with the effects of governing parameters on the characteristics are nearly independent of the flame configuration.
Download or read book Simulation of Lean Premixed Turbulent Combustion written by Robert K. Cheng and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: There is considerable technological interest in developingnew fuel-flexible combustion systems that can burn fuels such ashydrogenor syngas. Lean premixed systems have the potential to burn thesetypes of fuels with high efficiency and low NOx emissions due to reducedburnt gas temperatures. Although traditional scientific approaches basedon theory and laboratory experiment have played essential roles indeveloping our current understanding of premixed combustion, they areunable to meet the challenges of designing fuel-flexible lean premixedcombustion devices. Computation, with itsability to deal with complexityand its unlimited access to data, hasthe potential for addressing thesechallenges. Realizing this potential requires the ability to perform highfidelity simulations of turbulent lean premixed flames under realisticconditions. In this paper, we examine the specialized mathematicalstructure of these combustion problems and discuss simulation approachesthat exploit this structure. Using these ideas we can dramatically reducecomputational cost, making it possible to perform high-fidelitysimulations of realistic flames. We illustrate this methodology byconsidering ultra-lean hydrogen flames and discuss how this type ofsimulation is changing the way researchers study combustion.
Download or read book Experiments and Numerical Simulations of Turbulent Combustion of Diluted Sprays written by Bart Merci and published by Springer Science & Business Media. This book was released on 2014-03-27 with total page 167 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reflects the results of the 2nd and 3rd International Workshops on Turbulent Spray Combustion. The focus is on progress in experiments and numerical simulations for two-phase flows, with emphasis on spray combustion. Knowledge of the dominant phenomena and their interactions allows development of predictive models and their use in combustor and gas turbine design. Experts and young researchers present the state-of-the-art results, report on the latest developments and exchange ideas in the areas of experiments, modelling and simulation of reactive multiphase flows. The first chapter reflects on flame structure, auto-ignition and atomization with reference to well-characterized burners, to be implemented by modellers with relative ease. The second chapter presents an overview of first simulation results on target test cases, developed at the occasion of the 1st International Workshop on Turbulent Spray Combustion. In the third chapter, evaporation rate modelling aspects are covered, while the fourth chapter deals with evaporation effects in the context of flamelet models. In chapter five, LES simulation results are discussed for variable fuel and mass loading. The final chapter discusses PDF modelling of turbulent spray combustion. In short, the contributions in this book are highly valuable for the research community in this field, providing in-depth insight into some of the many aspects of dilute turbulent spray combustion.
Download or read book Experimental Investigation of the Dynamics and Structure of Lean premixed Turbulent Combustion written by Frank Tat Cheong Yuen and published by . This book was released on 2009 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbulent premixed propane/air and methane/air flames were studied using planar Rayleigh scattering and particle image velocimetry on a stabilized Bunsen type burner. The fuel-air equivalence ratio was varied from &phis; = 0:7 to 1.0 for propane flames, and from &phis; = 0:6 to 1.0 for methane flames. The non-dimensional turbulence intensity, u'/ SL (ratio of fluctuation velocity to laminar burning velocity), covered the range from 3 to 24, equivalent to conditions of corrugated flamelets and thin reaction zones regimes. Temperature gradients decreased with the increasing u'/SL and levelled off beyond u'/SL > 10 for both propane and methane flames. Flame front thickness increased slightly as u'/SL increased for both mixtures, although the thickness increase was more noticeable for propane flames, which meant the thermal flame front structure was being thickened. A zone of higher temperature was observed on the average temperature profile in the preheat zone of the flame front as well as some instantaneous temperature profiles at the highest u'/SL. Curvature probability density functions were similar to the Gaussian distribution at all u'/ SL for both mixtures and for all the flame sections. The mean curvature values decreased as a function of u'/ SL and approached zero. Flame front thickness was smaller when evaluated at flame front locations with zero curvature than that with curvature. Temperature gradients and FSD were larger when the flame curvature was zero. The combined thickness and FSD data suggest that the curvature effect is more dominant than that of the stretch by turbulent eddies during flame propagation. Integrated flame surface density for both propane and methane flames exhibited no dependance on u'/S L regardless of the FSD method used for evaluation. This observation implies that flame surface area may not be the dominant factor in increasing the turbulent burning velocity and the flamelet assumption may not be valid under the conditions studied. Dkappa term, the product of diffusivity evaluated at conditions studied and the flame front curvature, was a magnitude smaller than or the same magnitude as the laminar burning velocity.
Download or read book Lean Premixed Flame Structure in Intense Turbulence written by Sastri Purushottama Nandula and published by . This book was released on 2003 with total page 364 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Turbulent Combustion Modeling written by Tarek Echekki and published by Springer Science & Business Media. This book was released on 2010-12-25 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: Turbulent combustion sits at the interface of two important nonlinear, multiscale phenomena: chemistry and turbulence. Its study is extremely timely in view of the need to develop new combustion technologies in order to address challenges associated with climate change, energy source uncertainty, and air pollution. Despite the fact that modeling of turbulent combustion is a subject that has been researched for a number of years, its complexity implies that key issues are still eluding, and a theoretical description that is accurate enough to make turbulent combustion models rigorous and quantitative for industrial use is still lacking. In this book, prominent experts review most of the available approaches in modeling turbulent combustion, with particular focus on the exploding increase in computational resources that has allowed the simulation of increasingly detailed phenomena. The relevant algorithms are presented, the theoretical methods are explained, and various application examples are given. The book is intended for a relatively broad audience, including seasoned researchers and graduate students in engineering, applied mathematics and computational science, engine designers and computational fluid dynamics (CFD) practitioners, scientists at funding agencies, and anyone wishing to understand the state-of-the-art and the future directions of this scientifically challenging and practically important field.
Download or read book Combustion Characteristics of Lean Turbulent Pre mixed Flames with a Very Lean Co flow written by J. C. Hermanson and published by . This book was released on 1997 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book On the Experimental and Theoretical Investigations of Lean Partially Premixed Combustion Burning Speed Flame Instability and Plasma Formation of Alternative Fuels at High Temperatures and Pressures written by Omid Askari and published by . This book was released on 2016 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation investigates the combustion and injection fundamental characteristics of different alternative fuels both experimentally and theoretically. The subjects such as lean partially premixed combustion of methane/hydrogen/air/diluent, methane high pressure direct-injection, thermal plasma formation, thermodynamic properties of hydrocarbon/air mixtures at high temperatures, laminar flames and flame morphology of synthetic gas (syngas) and Gas-to-Liquid (GTL) fuels were extensively studied in this work. These subjects will be summarized in three following paragraphs. The fundamentals of spray and partially premixed combustion characteristics of directly injected methane in a constant volume combustion chamber have been experimentally studied. The injected fuel jet generates turbulence in the vessel and forms a turbulent heterogeneous fuel-air mixture in the vessel, similar to that in a Compressed Natural Gas (CNG) Direct-Injection (DI) engines. The effect of different characteristics parameters such as spark delay time, stratification ratio, turbulence intensity, fuel injection pressure, chamber pressure, chamber temperature, Exhaust Gas recirculation (EGR) addition, hydrogen addition and equivalence ratio on flame propagation and emission concentrations were analyzed. As a part of this work and for the purpose of control and calibration of high pressure injector, spray development and characteristics including spray tip penetration, spray cone angle and overall equivalence ratio were evaluated under a wide range of fuel injection pressures of 30 to 90 atm and different chamber pressures of 1 to 5 atm. Thermodynamic properties of hydrocarbon/air plasma mixtures at ultra-high temperatures must be precisely calculated due to important influence on the flame kernel formation and propagation in combusting flows and spark discharge applications. A new algorithm based on the statistical thermodynamics was developed to calculate the ultra-high temperature plasma composition and thermodynamic properties. The method was applied to compute the thermodynamic properties of hydrogen/air and methane/air plasma mixtures for a wide range of temperatures (1,000-100,000 K), pressures (10−6-100 atm) and different equivalence ratios within flammability limit. In calculating the individual thermodynamic properties of the atomic species, the Debye-Huckel cutoff criterion has been used for terminating the series expression of the electronic partition function. A new differential-based multi-shell model was developed in conjunction with Schlieren photography to measure laminar burning speed and to study the flame instabilities for different alternative fuels such as syngas and GTL. Flame instabilities such as cracking and wrinkling were observed during flame propagation and discussed in terms of the hydrodynamic and thermo-diffusive effects. Laminar burning speeds were measured using pressure rise data during flame propagation and power law correlations were developed over a wide range of temperatures, pressures and equivalence ratios. As a part of this work, the effect of EGR addition and substitution of nitrogen with helium in air on flame morphology and laminar burning speed were extensively investigated. The effect of cell formation on flame surface area of syngas fuel in terms of a newly defined parameter called cellularity factor was also evaluated. In addition to that the experimental onset of auto-ignition and theoretical ignition delay times of premixed GTL/air mixture were determined at high pressures and low temperatures over a wide range of equivalence ratios.
Download or read book Combustion and Mass Transfer written by D Brian Spalding and published by Elsevier. This book was released on 2013-10-22 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion and Mass Transfer: A Textbook with Multiple-Choice Exercises for Engineering Students is a 20-chapter lecture text that covers various aspects of combustion and mass transfer. Each of the 20 chapters is provided with a set partly analytical and multiple-choice tutorial exercises, designed to assist the student to understand the material of the lectures. The opening chapters deal with the importance of combustion and mass transfer processes. The succeeding chapters survey the concepts and principles of droplet vaporization, droplet combustion, liquid-propellant rocket, and laminar and turbulent jet. These topics are followed by discussions of laminar and turbulent diffusion flame, kinetically-influenced phenomena, chemical kinetics, and spontaneous ignition. The remaining chapters consider the basic concepts of stirred reactor, flame stabilization, laminar flame propagation, spark ignition, and coal-particle combustion. This book is intended for undergraduate mechanical engineering students.
Download or read book A Comparison of Experimental Measurements and Numerical Calculations of Ignition Delay in Lean Premixed H2 O2 N2 Turbulent Combustion written by Dong Ho Lee and published by . This book was released on 1998 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental Study of Premixed Flames in a Taylor Couette Combustor written by Vahid Vaezi and published by . This book was released on 2000 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt:
