Download or read book Experimental Investigations of Nanosceond Pulsed Laser Micromachining of Metal Using Thin Film Microsensors written by Hong Seok Choi and published by . This book was released on 2007 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Experimental and Theoretical Investigations of Nanosecond Fibre Laser Micromachining written by Eleri Williams and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Femtosecond Pulsed Laser Deposition and Patterning of Thin Films for MEMS written by Michael Joseph Stock and published by . This book was released on 2003 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: Procedural variables such as fluence, polarization, pulse width, machining speed, and material properties are investigated to determine their effects on the PLD and laser micromachining of aluminum magnesium boride. In this work, a 120-fs pulsed, 800-nm wavelength Ti: Sapphire laser was used for micromachining thin films of ultra-hard AlMgB14 and polysilicon thin films on silicon substrate. Polysilicon was first deposited by low-pressure chemical vapor deposition followed by boride using femtosecond pulsed laser deposition. Channels were then machined in thin films to pattern a device that would produce a linear resistance/deflection curve. Results show that the ultrafast laser has precisely ablated the thin films. However, the high-energy fluence used in single-pass surface micromachining enabled the formation of recast layer of molten silicon substrate ejected by vapor pressure, and conglomerates of re-condensed material at a distance from the feature. Multi-pass surface micromachining at low energy fluences eliminated the recast layers and produced clean features. Ultrafast laser micromachining is certainly beneficial over wet and dry etching in reproducibility, material choice, and minimal number of processing steps. Thin films of ultra-hard AlMgB14 were grown on Si (100) substrates at 300 K using femtosecond pulsed Ti:sapphire laser and subsequently annealed in argon gas up to 1373 K for two hours. X-ray photoelectron spectroscopy, X-ray diffraction, atomic force microscope, and nanoindentation were employed to study the composition, microstructure and hardness of thin films. Results were compared with nanosecond pulsed KrF excimer laser-deposited films. The as-deposited and post-annealed films (up to 1173 K), independent of the pulse width, exhibited amorphous structures with a hardness of 40 GPa. However, post-annealing at higher temperatures has varied effects on crystallization depending on the pulse width. The effect of pulse width on the microstructure and quality of thin films is discussed.
Download or read book Predictive Modeling Simulation and Optimization of Laser Processing Techniques written by Luis Ernesto Criales Escobar and published by . This book was released on 2016 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the most frequently evolving areas of research is the utilization of lasers for micro-manufacturing and additive manufacturing purposes. The use of laser beam as a tool for manufacturing arises from the need for flexible and rapid manufacturing at a low-to-mid cost. Laser micro-machining provides an advantage over mechanical micro-machining due to the faster production times of large batch sizes and the high costs associated with specific tools. Laser based additive manufacturing enables processing of powder metals for direct and rapid fabrication of products. Therefore, laser processing can be viewed as a fast, flexible, and cost-effective approach compared to traditional manufacturing processes. Two types of laser processing techniques are studied: laser ablation of polymers for micro-channel fabrication and selective laser melting of metal powders. Initially, a feasibility study for laser-based micro-channel fabrication of poly(dimethylsiloxane) (PDMS) via experimentation is presented. In particular, the effectiveness of utilizing a nanosecond-pulsed laser as the energy source for laser ablation is studied. The results are analyzed statistically and a relationship between process parameters and micro-channel dimensions is established. Additionally, a process model is introduced for predicting channel depth. Model outputs are compared and analyzed to experimental results. The second part of this research focuses on a physics-based FEM approach for predicting the temperature profile and melt pool geometry in selective laser melting (SLM) of metal powders. Temperature profiles are calculated for a moving laser heat source to understand the temperature rise due to heating during SLM. Based on the predicted temperature distributions, melt pool geometry, i.e. the locations at which melting of the powder material occurs, is determined. Simulation results are compared against data obtained from experimental Inconel 625 test coupons fabricated at the National Institute for Standards & Technology via response surface methodology techniques. The main goal of this research is to develop a comprehensive predictive model with which the effect of powder material properties and laser process parameters on the built quality and integrity of SLM-produced parts can be better understood. By optimizing process parameters, SLM as an additive manufacturing technique is not only possible, but also practical and reproducible.
Download or read book Laser Precision Microfabrication written by Koji Sugioka and published by Springer. This book was released on 2010-08-13 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: Miniaturization and high precision are rapidly becoming a requirement for many industrial processes and products. As a result, there is greater interest in the use of laser microfabrication technology to achieve these goals. This book composed of 16 chapters covers all the topics of laser precision processing from fundamental aspects to industrial applications to both inorganic and biological materials. It reviews the sate of the art of research and technological development in the area of laser processing.
Download or read book Advances in Micro and Nano Manufacturing and Surface Engineering written by M. S. Shunmugam and published by Springer Nature. This book was released on 2019-11-30 with total page 720 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume presents research papers on micro and nano manufacturing and surface engineering which were presented during the 7th International and 28th All India Manufacturing Technology, Design and Research conference 2018 (AIMTDR 2018). The papers discuss the latest advances in miniature manufacturing, the machining of miniature components and features as well as improvement of surface properties. This volume will be of interest to academicians, researchers, and practicing engineers alike.
Download or read book Handbook of Modern Sensors written by Jacob Fraden and published by Springer Science & Business Media. This book was released on 2006-04-29 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: Seven years have passed since the publication of the previous edition of this book. During that time, sensor technologies have made a remarkable leap forward. The sensitivity of the sensors became higher, the dimensions became smaller, the sel- tivity became better, and the prices became lower. What have not changed are the fundamental principles of the sensor design. They are still governed by the laws of Nature. Arguably one of the greatest geniuses who ever lived, Leonardo Da Vinci, had his own peculiar way of praying. He was saying, “Oh Lord, thanks for Thou do not violate your own laws. ” It is comforting indeed that the laws of Nature do not change as time goes by; it is just our appreciation of them that is being re?ned. Thus, this new edition examines the same good old laws of Nature that are employed in the designs of various sensors. This has not changed much since the previous edition. Yet, the sections that describe the practical designs are revised substantially. Recent ideas and developments have been added, and less important and nonessential designs were dropped. Probably the most dramatic recent progress in the sensor technologies relates to wide use of MEMS and MEOMS (micro-electro-mechanical systems and micro-electro-opto-mechanical systems). These are examined in this new edition with greater detail. This book is about devices commonly called sensors. The invention of a - croprocessor has brought highly sophisticated instruments into our everyday lives.
Download or read book Laser Fabrication and Machining of Materials written by Narendra B. Dahotre and published by Springer Science & Business Media. This book was released on 2008-01-25 with total page 565 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the fundamental principles and physical phenomena behind laser-based fabrication and machining processes. It also gives an overview of their existing and potential applications. With laser machining an emerging area in various applications ranging from bulk machining in metal forming to micromachining and microstructuring, this book provides a link between advanced materials and advanced manufacturing techniques. The interdisciplinary approach of this text will help prepare students and researchers for the next generation of manufacturing.
Download or read book Semiconductor Gas Sensors written by Raivo Jaaniso and published by Woodhead Publishing. This book was released on 2019-09-24 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: Semiconductor Gas Sensors, Second Edition, summarizes recent research on basic principles, new materials and emerging technologies in this essential field. Chapters cover the foundation of the underlying principles and sensing mechanisms of gas sensors, include expanded content on gas sensing characteristics, such as response, sensitivity and cross-sensitivity, present an overview of the nanomaterials utilized for gas sensing, and review the latest applications for semiconductor gas sensors, including environmental monitoring, indoor monitoring, medical applications, CMOS integration and chemical warfare agents. This second edition has been completely updated, thus ensuring it reflects current literature and the latest materials systems and applications. Includes an overview of key applications, with new chapters on indoor monitoring and medical applications Reviews developments in gas sensors and sensing methods, including an expanded section on gas sensor theory Discusses the use of nanomaterials in gas sensing, with new chapters on single-layer graphene sensors, graphene oxide sensors, printed sensors, and much more
Download or read book Micro Manufacturing Technologies and Their Applications written by Irene Fassi and published by Springer. This book was released on 2017-01-31 with total page 301 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides in-depth theoretical and practical information on recent advances in micro-manufacturing technologies and processes, covering such topics as micro-injection moulding, micro-cutting, micro-EDM, micro-assembly, micro-additive manufacturing, moulded interconnected devices, and microscale metrology. It is designed to provide complementary material for the related e-learning platform on micro-manufacturing developed within the framework of the Leonardo da Vinci project 2013-3748/542424: MIMAN-T: Micro-Manufacturing Training System for SMEs. The book is mainly addressed to technicians and prospective professionals in the sector and will serve as an easily usable tool to facilitate the translation of micro-manufacturing technologies into tangible industrial benefits. Numerous examples are included to assist readers in learning and implementing the described technologies. In addition, an individual chapter is devoted to technological foresight, addressing market analysis and business models for micro-manufacturers.
Download or read book Laser Surface Interactions for New Materials Production written by Antonio Miotello and published by Springer Science & Business Media. This book was released on 2009-12-05 with total page 367 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides an overview on nanosecond and ultra-short laser-induced phenomena and the related diagnostics. It grew from the lectures of the International School "Laser-surface interactions for new materials production" held in July 2008.
Download or read book Non traditional Micromachining Processes written by Golam Kibria and published by Springer. This book was released on 2017-03-07 with total page 431 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a complete coverage of micromachining processes from their basic material removal phenomena to past and recent research carried by a number of researchers worldwide. Chapters on effective utilization of material resources, improved efficiency, reliability, durability, and cost effectiveness of the products are presented. This book provides the reader with new and recent developments in the field of micromachining and microfabrication of engineering materials.
Download or read book Textbook of Nanoscience and Nanotechnology written by B.S. Murty and published by Springer Science & Business Media. This book was released on 2013-12-06 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is meant to serve as a textbook for beginners in the field of nanoscience and nanotechnology. It can also be used as additional reading in this multifaceted area. It covers the entire spectrum of nanoscience and technology: introduction, terminology, historical perspectives of this domain of science, unique and widely differing properties, advances in the various synthesis, consolidation and characterization techniques, applications of nanoscience and technology and emerging materials and technologies.
Download or read book Ferroelectric Thin Films written by Masanori Okuyama and published by Springer Science & Business Media. This book was released on 2005-02-22 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ferroelectric thin films continue to attract much attention due to their developing applications in memory devices, FeRAM, infrared sensors, piezoelectric sensors and actuators. This book, aimed at students, researchers and developers, gives detailed information about the basic properties of these materials and the associated device physics. The contributing authors are acknowledged experts in the field.
Download or read book Nano Microscale Heat Transfer written by Zhuomin M. Zhang and published by Springer Nature. This book was released on 2020-06-23 with total page 780 pages. Available in PDF, EPUB and Kindle. Book excerpt: This substantially updated and augmented second edition adds over 200 pages of text covering and an array of newer developments in nanoscale thermal transport. In Nano/Microscale Heat Transfer, 2nd edition, Dr. Zhang expands his classroom-proven text to incorporate thermal conductivity spectroscopy, time-domain and frequency-domain thermoreflectance techniques, quantum size effect on specific heat, coherent phonon, minimum thermal conductivity, interface thermal conductance, thermal interface materials, 2D sheet materials and their unique thermal properties, soft materials, first-principles simulation, hyperbolic metamaterials, magnetic polaritons, and new near-field radiation experiments and numerical simulations. Informed by over 12 years use, the author’s research experience, and feedback from teaching faculty, the book has been reorganized in many sections and enriched with more examples and homework problems. Solutions for selected problems are also available to qualified faculty via a password-protected website.• Substantially updates and augments the widely adopted original edition, adding over 200 pages and many new illustrations;• Incorporates student and faculty feedback from a decade of classroom use;• Elucidates concepts explained with many examples and illustrations;• Supports student application of theory with 300 homework problems;• Maximizes reader understanding of micro/nanoscale thermophysical properties and processes and how to apply them to thermal science and engineering;• Features MATLAB codes for working with size and temperature effects on thermal conductivity, specific heat of nanostructures, thin-film optics, RCWA, and near-field radiation.
Download or read book Ferroelectric Thin Films written by Carlos Paz de Araujo and published by Taylor & Francis. This book was released on 1996 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt: The impetus for the rapid development of thin film technology, relative to that of bulk materials, is its application to a variety of microelectronic products. Many of the characteristics of thin film ferroelectric materials are utilized in the development of these products - namely, their nonvolatile memory and piezoelectric, pyroelectric, and electro-optic properties. It is befitting, therefore, that the first of a set of three complementary books with the general title Integrated Ferroelectric Devices and Technologies focuses on the synthesis of thin film ferroelectric materials and their basic properties. Because it is a basic introduction to the chemistry, materials science, processing, and physics of the materials from which integrated ferroelectrics are made, newcomers to this field as well as veterans will find this book self-contained and invaluable in acquiring the diverse elements requisite to success in their work in this area. It is directed at electronic engineers and physicists as well as process and system engineers, ceramicists, and chemists involved in the research, design, development, manufacturing, and utilization of thin film ferroelectric materials.
Download or read book Optical Diagnostics for Thin Film Processing written by Irving P. Herman and published by Elsevier. This book was released on 1996-10-23 with total page 815 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume describes the increasing role of in situ optical diagnostics in thin film processing for applications ranging from fundamental science studies to process development to control during manufacturing. The key advantage of optical diagnostics in these applications is that they are usually noninvasive and nonintrusive. Optical probes of the surface, film, wafer, and gas above the wafer are described for many processes, including plasma etching, MBE, MOCVD, and rapid thermal processing. For each optical technique, the underlying principles are presented, modes of experimental implementation are described, and applications of the diagnostic in thin film processing are analyzed, with examples drawn from microelectronics and optoelectronics. Special attention is paid to real-time probing of the surface, to the noninvasive measurement of temperature, and to the use of optical probes for process control. Optical Diagnostics for Thin Film Processing is unique. No other volume explores the real-time application of optical techniques in all modes of thin film processing. The text can be used by students and those new to the topic as an introduction and review of the subject. It also serves as a comprehensive resource for engineers, technicians, researchers, and scientists already working in the field. The only volume that comprehensively explores in situ, real-time, optical probes for all types of thin film processing Useful as an introduction to the subject or as a resource handbook Covers a wide range of thin film processes including plasma etching, MBE, MOCVD, and rapid thermal processing Examples emphasize applications in microelectronics and optoelectronics Introductory chapter serves as a guide to all optical diagnostics and their applications Each chapter presents the underlying principles, experimental implementation, and applications for a specific optical diagnostic
