Download or read book Evaluation of Select Methods of Corrosion Control Corrosion Prevention and Repair in Reinforced Concrete Bridges written by Habib Tabatabai and published by . This book was released on 2009 with total page 376 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Long term Performance of Corrosion Inhibitors Used in Repair of Reinforced Concrete Bridge Components written by Moavin Islam and published by DIANE Publishing. This book was released on 2003 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary objective of the project was to determine the effectiveness of cathodic protection, electrochemical chloride extraction, and corrosion-inhibitor treatment systems installed during the SHRP effort through the long-term evaluation of 32 field test sites and a number of laboratory concrete slab specimens. The FHWA program required monitoring the long-term performance of corrosion inhibitor treatments on selected components of four bridges that were treated and evaluated under SHRP C-103. Three evaluations over a period of 5 years were conducted on structures located in Minnesota, New York and Pennsylvania, and two evaluations were conducted on a structure in Washington State. An analysis of the results concluded that neither of the corrosion inhibitors evaluated in this study, using the specified repairs and exposed to the specific environments, provided any corrosion-inhibiting benefit. Shrinkage cracking plagued repairs at all test sites except for the Washington site.
Download or read book Evaluation of Corrosion Protection Methods for Reinforced Concrete Highway Structures written by Jennifer L. Kepler and published by . This book was released on 2000 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the 1970s, research projects and field studies have been conducted on different methods for protecting reinforced concrete bridges from corrosion damage. The methods include alternative reinforcement and slab design, barrier methods, electrochemical methods, and corrosion inhibitors. Each method and its underlying principles are described, performance results of laboratory and/or field trials are reviewed, and systems are evaluated based on the results of the trials. Using performance results from the studies and costs obtained from transportation agencies, an economic analysis is used to estimate the cost of each system over a 75-year economic life using discount rates of 2%, 4% and 6%.
Download or read book Manual on Service Life of Corrosion damaged Reinforced Concrete Bridge Superstructure Elements written by Ali Akbar Sohanghpurwala and published by Transportation Research Board. This book was released on 2006 with total page 72 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Performance Evaluation of Various Corrosion Protection Systems of Bridges in Colorado written by Yunping Xi and published by . This book was released on 2004 with total page 166 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion of reinforced concrete structures has been a significant problem for many state and transportation agencies since the application of deicing salts was introduced. Much research has been conducted to develop corrosion protection systems that can prolong the life span of reinforced concrete structures. The Colorado Department of Transportation (CDOT) has several routine and experimental measures to prevent corrosion of the rebar including epoxy-coated rebar, calcium nitrite admixture, organic corrosion inhibitors, a thick cover of quality concrete, and a waterproofing membrane covered by an asphalt overlay. An extensive literature review was performed to collect information on various corrosion protection systems that have been used in the U.S. and around the world. Current CDOT practices in terms of corrosion protection measures were reviewed. A draft inspection plan for Colorado's bridge structures was proposed.
Download or read book Corrosion of Steel in Concrete written by John P. Broomfield and published by CRC Press. This book was released on 2023-01-31 with total page 305 pages. Available in PDF, EPUB and Kindle. Book excerpt: Corrosion of Steel in Concrete: Understanding, Investigation and Repair is a guide for designing, constructing and maintaining reinforced concrete structures, such as buildings and bridges which are subject to reinforcement corrosion. It presents the basics of theory and practice in steel corrosion in concrete and reviews the latest research and developments, such as progress on measuring the corrosion threshold for chloride-induced corrosion. This third edition compares the currently proliferating major national and international standards and guidance documents. New developments are considered, such as hybrid anodes for electrochemical treatment and the latest research and developments in assessment, such as the use of ground penetrating radar to measure the chloride content of the concrete cover. It overhauls coverage of electrochemical repair and rehabilitation techniques and outlines recent innovations in structural repair and construction and investigates their implications for durability. The book is ideal for practitioners and graduate students in structural engineering and concrete technology.
Download or read book Case Studies of Rehabilitation Repair Retrofitting and Strengthening of Structures written by Mourad M. Bakhoum and published by IABSE. This book was released on 2010 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Evaluation of Selected Repair Methods for Chloride included Corrosion Damaged Reinforced Concrete Railway Bridges written by Mohamed Jogiat and published by . This book was released on 2019 with total page 232 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Sustainable Civil Engineering at the Beginning of Third Millennium written by Umut Türker and published by Springer Nature. This book was released on with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Bibliography on the Corrosion and Protection of Steel in Concrete written by E. Escalante and published by . This book was released on 1979 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Corrosion of Steel in Concrete written by Luca Bertolini and published by John Wiley & Sons. This book was released on 2013-02-26 with total page 389 pages. Available in PDF, EPUB and Kindle. Book excerpt: Steel-reinforced concrete is used ubiquitously as a building material due to its unique combination of the high compressive strength of concrete and the high tensile strength of steel. Therefore, reinforced concrete is an ideal composite material that is used for a wide range of applications in structural engineering such as buildings, bridges, tunnels, harbor quays, foundations, tanks and pipes. To ensure durability of these structures, however, measures must be taken to prevent, diagnose and, if necessary, repair damage to the material especially due to corrosion of the steel reinforcement. The book examines the different aspects of corrosion of steel in concrete, starting from basic and essential mechanisms of the phenomenon, moving up to practical consequences for designers, contractors and owners both for new and existing reinforced and prestressed concrete structures. It covers general aspects of corrosion and protection of reinforcement, forms of attack in the presence of carbonation and chlorides, problems of hydrogen embrittlement as well as techniques of diagnosis, monitoring and repair. This second edition updates the contents with recent findings on the different topics considered and bibliographic references, with particular attention to recent European standards. This book is a self-contained treatment for civil and construction engineers, material scientists, advanced students and architects concerned with the design and maintenance of reinforced concrete structures. Readers will benefit from the knowledge, tools, and methods needed to understand corrosion in reinforced concrete and how to prevent it or keep it within acceptable limits.
Download or read book Corrosion of Reinforcement in Concrete EFC 25 written by J. Mietz and published by CRC Press. This book was released on 2020-08-13 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book compiles the full papers presented in the successful session "Corrosion of Steel in Concrete" at EUROCORR '97. It highlights the areas of technical development in this field, including monitoring of steel reinforcement corrosion, prevention of corrosion and electrochemical repair methods.
Download or read book Evaluation of Multiple Corrosion Protection Systems and Corrosion Inhibitors for Reinforced Concrete Bridge Decks written by Lihua Xing and published by . This book was released on 2010 with total page 459 pages. Available in PDF, EPUB and Kindle. Book excerpt: The corrosion performance of different corrosion protection systems is evaluated using the mortar-wrapped rapid macrocell test, bench-scale tests (the Southern Exposure, cracked beam, and ASTM G109 tests), and field tests. The systems include conventional steel with three different corrosion inhibitors (DCI-S, Hycrete, and Rheocrete), epoxy-coated reinforcement (ECR) with three different corrosion inhibitors and ECR with a primer coating containing microencapsulated calcium nitrite, multiple-coated reinforcement with a zinc layer underlying an epoxy coating, ECR with zinc chromate pretreatment before application of the epoxy coating to improve adhesion between the epoxy and the underlying steel, ECR with improved adhesion epoxy coatings, and pickled 2205 duplex stainless steel. Conventional steel in concretes with two different water-cement ratios (0.45 and 0.35) is also tested. Of these systems, specimens containing conventional steel or conventional epoxy-coated steel serve as controls. The critical chloride thresholds of conventional steel in concrete with different corrosion inhibitors and zinc-coated reinforcement are determined. The results of the tests are used in an economic analysis of bridge decks containing different corrosion protection systems over a design life of 75 years. The results indicate that a reduced water-cement ratio improves the corrosion resistance of conventional steel in uncracked concrete compared to the same steel in concrete with a higher water-cement ratio. The use of a corrosion inhibitor improves the corrosion resistance of conventional steel in both cracked and uncracked concrete and delays the onset of corrosion in uncracked concrete, but provides only a very limited improvement in the corrosion resistance of epoxy-coated reinforcement due to the high corrosion resistance provided by the epoxy coating itself. Based on results in the field tests, the epoxy-coated bars with a primer containing microencapsulated calcium nitrite show no improvement in the corrosion resistance compared to conventional epoxy-coated reinforcement. Increased adhesion between the epoxy coating and reinforcing steel provides no improvement in the corrosion resistance of epoxy-coated reinforcement. The corrosion losses for multiple-coated reinforcement are comparable with those of conventional epoxy-coated reinforcement in the field tests in uncracked and cracked concrete. Corrosion potential measurements show that the zinc is corroded preferentially, providing protection for the underlying steel. Pickled 2205 stainless steel demonstrates excellent corrosion resistance, and no corrosion activity is observed for the pickled 2205 stainless steel in bridge decks, or in the SE, CB, or field test specimens after four years.
Download or read book Corrosion of Reinforcement in Concrete written by M Raupach and published by Woodhead Publishing. This book was released on 2014-01-23 with total page 337 pages. Available in PDF, EPUB and Kindle. Book excerpt: Given the widespread use of reinforced concrete in infrastructure, understanding the corrosion of this material is of major importance. As a result there has been a wealth of research into catalysts, inhibitors and effective means of monitoring the rate of corrosion. Corrosion of reinforcement in concrete: mechanisms, monitoring, inhibitors and rehabilitation techniques summarises some of the most significant research and its implications.The book begins by reviewing findings from various experiments designed to test the corrosion rate of metals induced by a range of factors. Later chapters discuss techniques for monitoring and testing for corrosion. The book concludes by assessing important methods of prevention, including corrosion inhibitors, protective coatings and electrochemical methods for protection, together with rehabilitation procedures for susceptible structures.Filled with practical examples and written by a distinguished team of international contributors, Corrosion of reinforcement in concrete: mechanisms, monitoring, inhibitors and rehabilitation techniques is an essential reference for civil engineers using reinforced concrete. Summarises research into catalysts, inhibitors and effective means of monitoring the rate of corrosion Concludes by assessing important methods of prevention
Download or read book Corrosion Protection Performance Evaluation of Low Permeable Concretes in Exposure Specimens written by Jerzy Zemajtis and published by . This book was released on 1999 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: The application of a mineral admixture or a combination of a mineral admixture with corrosion inhibitor are the methods used for the corrosion protection for reinforced concrete bridges. The results of a 1.5-year study on evaluation of three concretes with fly ash, slag cement (SC), and silica fume (SF) and one concrete with silica fume and a corrosion inhibitor (SFD) are presented. The specimens were built to simulate four exposure conditions typical for concrete bridges located in the coastal region or inland where deicing salts are used. The exposure conditions were horizontal, vertical, tidal, and immersed zones. The specimens were kept inside the laboratory and were exposed to weekly ponding cycles of 6% sodium chloride solution by weight. In addition, cover depth measurements from 21 bridge decks and chloride data from 3 bridge decks were used, together with laboratory data, in modeling the service lives of investigated corrosion protection methods. The methods used to assess the condition of the specimens included chloride concentration measurements, corrosion potentials, and corrosion rates (3LP). Additionally, visual observations were performed for identification of rust stains and cracking on concrete surfaces. The results of chloride testing indicate that the amount of chlorides present at the bar level is more than sufficient to initiate corrosion. Chloride and rapid permeability data demonstrate that for low permeable (LP) concretes there appears to be significant difference both in a rate of chloride ingress and in the diffusion coefficients in comparison to the controls. Corrosion potentials agree with corrosion rates and suggest the possibility of an active corrosion process development on control specimens during indoor exposure. The structural cracks that were observed in some specimens appeared to have no influence on the corrosion development on the bars in the vicinity of the these cracks. It was concluded that the silicone and duct tape protection was adequate. The cracking, other than structural, appeared to be related to the reinforcing steel corrosion, except the cracks in the horizontal zone of the specimen with slag cement which were probably caused by the subsidence cracking. The least number of cracks was observed on the SF and SFD specimens. Modeling the time as a function of probability of the end of functional service life (EFSL) was presented. It has been shown that the distributions of surface concentrations of chloride ions (CO) and diffusion constants (DC) are key elements in the model. Model predictions show that the LP concretes provide much better level of protection against moisture and chlorides than the A4 concrete alone. Application of a corrosion inhibitor causes an elevation of the chloride threshold resulting in an additional increase in time to EFSL. Recommendations are to continue monitoring until cracking has occurred in all specimens to a greater extent to better estimate the service lives of LP concretes than is presently known in the construction of concrete bridge components in Virginia. The specimens with LP concretes and one control (continuous reinforcement in the legs) should be taken to the Hampton Road North Tunnel Island and placed in the brackish water to a depth of the immersed zone at low tide for further exposure to chloride. The other control (non-continuous reinforcement in the legs) should remain in an outdoor exposure in Southwest Virginia like the Civil Engineering Materials Research Laboratory in Blacksburg, Virginia. Also more field studies are needed to better estimate distributions of surface chloride concentration and diffusion coefficient of Virginia bridge decks, and to confirm predicted times to EFSL for LP concretes.
Download or read book Evaluation of Two Corrosion Inhibitors Using Two Surface Application Methods for Reinforced Concrete Structures written by Stephen R. Sharp and published by . This book was released on 2004 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study investigated the use of penetrating corrosion inhibitors to extend the life of existing reinforced concrete bridge decks. The use of assisted (vacuum/pressure injection) and unassisted (diffusion) treatment methods and two inhibitors were evaluated. The inhibitors were FerroGard 903, from Sika Corp., and TPS-II, from Surtreat International. Testing was performed on exposure slabs with 15 lb/yd3 of NaCl in the top layer and no NaCl in the bottom layer. The slab design was a variation of the specimen design provided in ASTM G109, with each slab containing nine steel reinforcing rods instead of three. The exposure slabs had either a uniform cover over the top pieces of steel or an inclined cover over the steel. TPS-II was also evaluated on the deck of a bridge in Orange County, Virginia. The study found that when applied to the concrete surface, neither inhibitor penetrated the concrete to reach the steel reinforcement. The vacuum/pressure injection method showed promise but requires refinement. In addition, based on macro-cell measurements, a sufficient quantity of inhibitor can be injected into the concrete to reduce the charge passed.
Download or read book Evaluation of the Effectiveness of Surface Applied Corrosion Inhibitors for Concrete Bridges written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Deicing salts and salt-water spray can cause serious corrosion problems for reinforced concrete bridge structures. These problems can lead to costly and labor intensive repair and even replacement of the structure. Surface applied corrosion inhibitors are potentially a useful and cost effective way to prolong the life of existing structures. The purpose of this research project was to evaluate the effectiveness of commercially available corrosion inhibitors for surface treatments of existing reinforced concrete bridges. Reinforced concrete specimens were cast with different levels of initial chloride contents, coated with one of six products tested, and placed in accelerated corrosion environments. Each manufacturer donated their corresponding products for use in the experiment. The manufacturers were also given the test matrix and parameters in advance of the product application and invited to participate in the application process. Environmental conditions, voltmeter, and half cell potential readings were taken on a weekly basis in accordance with ASTM standards. Intermittently, some of these specimens were removed from their environments and evaluated on a visual, mass loss, strength loss, and chloride content basis. This data was then compiled and compared to each other and to control specimens located in a non-corrosive environment. It was found that surface applied corrosion inhibitors delay the onset of corrosion and the speed of the corrosion process. It was also found that a maximum chloride content of 0.5% by cement weight exists beyond which none of the inhibitor products were useful. Suggestions for further research in this area of study are also included.
