Download or read book Residual Stresses written by A. Niku-Lari and published by Elsevier. This book was released on 2014-05-17 with total page 587 pages. Available in PDF, EPUB and Kindle. Book excerpt: Residual Stresses presents a collection of articles that provides information regarding the use of surface treatment systems. It discusses the developments in the technology and application of surface treatment. It addresses the influence of minor stresses on the performance of materials. Some of the topics covered in the book are the introduction to self-equilibrating stresses existing in materials, the stresses that form as a consequence of welding, the stresses made by machining, and the mechanical generation of self-stresses. The analysis of the stresses caused by thermal and thermochemical surface treatments is covered. The minor stresses in composite materials are discussed. The text describes the stresses in uranium and uranium alloys. The Trepan or ring core method, centre-hole method, and Sach's method are presented. A chapter of the volume is devoted to the measurement of residual stresses. Another section of the book focuses on the application of shot peened plates to residual stress distribution. The book will provide useful information to mechanics, engineers, students, and researchers.
Download or read book IIW Recommendations On Methods for Improving the Fatigue Strength of Welded Joints written by P J Haagensen and published by Woodhead Publishing. This book was released on 2013-01-25 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt: The weld toe is a primary source of fatigue cracking because of the severity of the stress concentration it produces. Weld toe improvement can increase the fatigue strength of new structures significantly. It can also be used to repair or upgrade existing structures. However, in practice there have been wide variations in the actual improvements in fatigue strength achieved. Based on an extensive testing programme organised by the IIW, this report reviews the main methods for weld toe improvement to increase fatigue strength: burr grinding, TIG dressing and hammer and needle peening. The report provides specifications for the practical use of each method, including equipment, weld preparation and operation. It also offers guidance on inspection, quality control and training as well as assessments of fatigue strength and thickness effects possible with each technique. IIW recommendations on methods for improving the fatigue strength of welded joints will allow a more consistent use of these methods and more predictable increases in fatigue strength. Provides specifications for the practical use of each weld toe method, including equipment, weld preparation and operation Offers guidance on inspection, quality control and training, as well as assessments of fatigue strength and thickness effects possible with each technique This report will allow a more consistent use of these methods and more predictable increases in fatigue strength
Download or read book Theory of Notch Stresses written by Heinz Neuber and published by . This book was released on 1946 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Texas written by James A. Michener and published by Dial Press. This book was released on 2014-01-21 with total page 1474 pages. Available in PDF, EPUB and Kindle. Book excerpt: Spanning four and a half centuries, James A. Michener’s monumental saga chronicles the epic history of Texas, from its Spanish roots in the age of the conquistadors to its current reputation as one of America’s most affluent, diverse, and provocative states. Among his finely drawn cast of characters, emotional and political alliances are made and broken, as the loyalties established over the course of each turbulent age inevitably collapse under the weight of wealth and industry. With Michener as our guide, Texas is a tale of patriotism and statesmanship, growth and development, violence and betrayal—a stunning achievement by a literary master. BONUS: This edition includes an excerpt from James A. Michener's Hawaii. Praise for Texas “Fascinating.”—Time “A book about oil and water, rangers and outlaws, frontier and settlement, money and power . . . [James A. Michener] manages to make history vivid.”—The Boston Globe “A sweeping panorama . . . [Michener] grapples earnestly with the Texas character in a way that Texas’s own writers often don’t.”—The Washington Post Book World “Vast, sprawling, and eclectic in population and geography, the state has just the sort of larger-than-life history that lends itself to Mr. Michener’s taste for multigenerational epics.”—The New York Times
Download or read book Fatigue and Fracture Testing of Weldments written by Harry I. McHenry and published by ASTM International. This book was released on 1990 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fifteen papers from a symposium held in Sparks, Nev., April 1988. They cover: low and high cycle fatigue, fatigue crack growth, corrosion fatigue, fracture toughness testing, and wide-plate testing. Annotation copyright Book News, Inc. Portland, Or.
Download or read book Advances in Fatigue Lifetime Predictive Techniques written by Michael R. Mitchell and published by ASTM International. This book was released on 1992 with total page 495 pages. Available in PDF, EPUB and Kindle. Book excerpt: Twenty-seven papers from fatigue researchers and practitioners review in detail recent progress in the development of methods to predict fatigue performance of materials and structures and to assess the extent to which these new methods are finding their way into practice. The papers, from the ASTM
Download or read book Mechanical Properties and Working of Metals and Alloys written by Amit Bhaduri and published by Springer. This book was released on 2018-05-12 with total page 758 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book is intended to serve as core text or handy reference on two key areas of metallic materials: (i) mechanical behavior and properties evaluated by mechanical testing; and (ii) different types of metal working or forming operations to produce useful shapes. The book consists of 16 chapters which are divided into two parts. The first part contains nine chapters which describe tension (including elastic stress – strain relation, relevant theory of plasticity, and strengthening methods), compression, hardness, bending, torsion – pure shear, impact loading, creep and stress rupture, fatigue, and fracture. The second part is composed of seven chapters and covers fundamentals of mechanical working, forging, rolling, extrusion, drawing of flat strip, round bar, and tube, deep drawing, and high-energy rate forming. The book comprises an exhaustive description of mechanical properties evaluated by testing of metals and metal working in sufficient depth and with reasonably wide coverage. The book is written in an easy-to-understand manner and includes many solved problems. More than 150 numerical problems and many multiple choice questions as exercise along with their answers have also been provided. The mathematical analyses are well elaborated without skipping any intermediate steps. Slab method of analysis or free-body equilibrium approach is used for the analytical treatment of mechanical working processes. For hot working processes, different frictional conditions (sliding, sticking and mixed sticking–sliding) have been considered to estimate the deformation loads. In addition to the slab method of analysis, this book also contains slip-line field theory, its application to the static system, and the steady state motion, Further, this book includes upper-bound theorem, and upper-bound solutions for indentation, compression, extrusion and strip drawing. The book can be used to teach graduate and undergraduate courses offered to students of mechanical, aerospace, production, manufacturing and metallurgical engineering disciplines. The book can also be used for metallurgists and practicing engineers in industry and development courses in the metallurgy and metallic manufacturing industries.
Download or read book Fundamentals of Metal Fatigue Analysis written by Julie A. Bannantine and published by Pearson. This book was released on 1990 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first book to present current methods and techniques of fatigue analysis, with a focus on developing basic skills for selecting appropriate analytical techniques. Contains numerous worked examples, chapter summaries, and problems. (vs. Fuchs/Stevens).
Download or read book Advances in Surface Treatments written by A. Niku-Lari and published by . This book was released on 1984 with total page 596 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Multiaxial Notch Fatigue written by Luca Susmel and published by Elsevier. This book was released on 2009-03-20 with total page 589 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal and composite components used in structural engineering not only contain geometrical features resulting in stress concentration phenomena, but they are also subjected to in-service multiaxial fatigue loading. To address the problem, structural engineers need reliable methodologies which allow for an adequate margin of safety. The book summarises methods devised by the author to design real components against multiaxial fatigue by taking full advantage not only of nominal but also of local stress-strain quantities.The book begins by reviewing definitions suitable for calculating the stress-strain quantities commonly used to perform fatigue assessment. The Modified Wöhler Curve Method is then explained in detail, by focusing attention on both the high- and the medium-cycle fatigue regime. The existing links between the multiaxial fatigue criterion and physical properties are also discussed. A procedure suitable for employing the method developed by the author to estimate fatigue damage both in notched and in welded components is explained. The Modified Manson-Coffin Curve method is investigated in depth, by reviewing those concepts playing a fundamental role in the so-called strain based approach. Lastly, the problem of performing the fatigue assessment of composite materials is addressed by considering design parameters influencing composite behaviour under complex cyclic loading paths and those criteria suitable for designing real components against multiaxial fatigue. The book also contains two appendices summarising experimental data from the technical literature. These appendices provide a unique and highly valuable resource for engineers. The appendices summarise around 100 values of the material characteristic length L, experimentally determined by testing specimens made of different engineering materials and about 4500 experimental fatigue results generated by testing plain, notched and welded specimens under constant-amplitude proportional and non-proportional multiaxial fatigue loading are listed. - Summarises methods devised by the author to design real components against multiaxial fatigue - Reviews definitions suitable for calculating the stress-strain quantities commonly used to perform fatigue assessment - Includes an in-depth explanation of both the Modified Wöhler Curve and Modified Manson-Coffin Curve Method
Download or read book Proceedings of the International Conference on Offshore Mechanics and Arctic Engineering written by and published by . This book was released on 1991 with total page 1244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue of Structures and Materials written by J. Schijve and published by Springer Science & Business Media. This book was released on 2008-12-16 with total page 627 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue of structures and materials covers a wide scope of different topics. The purpose of the present book is to explain these topics, to indicate how they can be analyzed, and how this can contribute to the designing of fatigue resistant structures and to prevent structural fatigue problems in service. Chapter 1 gives a general survey of the topic with brief comments on the signi?cance of the aspects involved. This serves as a kind of a program for the following chapters. The central issues in this book are predictions of fatigue properties and designing against fatigue. These objectives cannot be realized without a physical and mechanical understanding of all relevant conditions. In Chapter 2 the book starts with basic concepts of what happens in the material of a structure under cyclic loads. It illustrates the large number of variables which can affect fatigue properties and it provides the essential background knowledge for subsequent chapters. Different subjects are presented in the following main parts: • Basic chapters on fatigue properties and predictions (Chapters 2–8) • Load spectra and fatigue under variable-amplitude loading (Chapters 9–11) • Fatigue tests and scatter (Chapters 12 and 13) • Special fatigue conditions (Chapters 14–17) • Fatigue of joints and structures (Chapters 18–20) • Fiber-metal laminates (Chapter 21) Each chapter presents a discussion of a speci?c subject.
Download or read book The Theory of Critical Distances written by David Taylor and published by Elsevier. This book was released on 2010-07-07 with total page 307 pages. Available in PDF, EPUB and Kindle. Book excerpt: Critical distance methods are extremely useful for predicting fracture and fatigue in engineering components. They also represent an important development in the theory of fracture mechanics. Despite being in use for over fifty years in some fields, there has never been a book about these methods – until now. So why now? Because the increasing use of computer-aided stress analysis (by FEA and other techniques) has made these methods extremely easy to use in practical situations. This is turn has prompted researchers to re-examine the underlying theory with renewed interest. The Theory of Critical Distances begins with a general introduction to the phenomena of mechanical failure in materials: a basic understanding of solid mechanics and materials engineering is assumed, though appropriate introductory references are provided where necessary. After a simple explanation of how to use critical distance methods, and a more detailed exposition of the methods including their history and classification, the book continues by showing examples of how critical distance approaches can be applied to predict fracture and fatigue in different classes of materials. Subsequent chapters include some more complex theoretical areas, such as multiaxial loading and contact problems, and a range of practical examples using case studies of real engineering components taken from the author's own consultancy work. The Theory of Critical Distances will be of interest to a range of readers, from academic researchers concerned with the theoretical basis of the subject, to industrial engineers who wish to incorporate the method into modern computer-aided design and analysis. - Comprehensive collection of published data, plus new data from the author's own laboratories - A simple 'how-to-do-it' exposition of the method, plus examples and case studies - Detailed theoretical treatment - Covers all classes of materials: metals, polymers, ceramics and composites - Includes fracture, fatigue, fretting, size effects and multiaxial loading
Download or read book Handbook of Residual Stress and Deformation of Steel written by George E. Totten and published by ASM International. This book was released on 2002 with total page 496 pages. Available in PDF, EPUB and Kindle. Book excerpt: Annotation Examines the factors that contribute to overall steel deformation problems. The 27 articles address the effect of materials and processing, the measurement and prediction of residual stress and distortion, and residual stress formation in the shaping of materials, during hardening processes, and during manufacturing processes. Some of the topics are the stability and relaxation behavior of macro and micro residual stresses, stress determination in coatings, the effects of process equipment design, the application of metallo- thermo-mechanic to quenching, inducing compressive stresses through controlled shot peening, and the origin and assessment of residual stresses during welding and brazing. Annotation c. Book News, Inc., Portland, OR (booknews.com)
Download or read book Fatigue Assessment of Welded Joints by Local Approaches written by Dieter Radaj and published by Woodhead Publishing. This book was released on 2006-10-30 with total page 661 pages. Available in PDF, EPUB and Kindle. Book excerpt: Local approaches to fatigue assessment are used to predict the structural durability of welded joints, to optimise their design and to evaluate unforeseen joint failures. This standard work provides a systematic survey of the principles and practical applications of the various methods. It covers the hot spot structural stress approach to fatigue in general, the notch stress and notch strain approach to crack initiation and the fracture mechanics approach to crack propagation. Seam-welded and spot-welded joints in structural steels and aluminium alloys are also considered.This completely reworked second edition takes into account the tremendous progress in understanding and applying local approaches which has been achieved in the last decade. It is a standard reference for designers, structural analysts and testing engineers who are responsible for the fatigue-resistant in-service behaviour of welded structures. - Completely reworked second edition of a standard work providing a systematic survey of the principles and practical applications of the various methods - Covers the hot spot structural stress approach to fatigue in general, the notch stress and notch strain approach to crack initiation and the fracture mechanics approach to crack propagation. - Written by a distinguished team of authors
Download or read book Fracture Fatigue Failure and Damage Evolution Volume 8 written by Allison M. Beese and published by Springer. This book was released on 2015-11-07 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fracture, Fatigue, Failure and Damage Evolution, Volume 8 represents the eighth of nine volumes of technical papers presented at the Society for Experimental Mechanics (SEM) 15th International Congress & Exposition on Experimental and Applied Mechanics, held at Costa Mesa, California, June 8-11, 2015. The full set of proceedings also includes volumes on: Dynamic Behavior of Materials, Challenges in Mechanics of Time Dependent Materials, Advancement of Optical Methods in Experimental Mechanics, Experimental and Applied Mechanics, 16th International Symposium on MEMS and Nanotechnology, International Symposium on the Mechanics of Composite and Multi-functional Materials, 5th International Symposium on the Mechanics of Biological Systems and Materials, International Symposium on the Mechanics of Composite and Multi-functional Materials; and Residual Stress, Thermomechanics & Infrared Imaging, Hybrid Techniques and Inverse Problems.
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1972 with total page 1056 pages. Available in PDF, EPUB and Kindle. Book excerpt:
