Download or read book Enhancement of Pool Boiling Heat Transfer with Electrohydrodynamics and Its Fundamental Study written by Sri Laxmi Priya Raghupathi and published by . This book was released on 1998 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book EHD enhanced Pool Boiling Heat Transfer written by Majid Ali Faani Tabrizi Nezhaad and published by . This book was released on 1997 with total page 492 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Advances in Heat Transfer written by and published by Academic Press. This book was released on 1999-02-24 with total page 543 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Heat Transfer is designed to fill the information gap between regularly scheduled journals and university level textbooks by providing in-depth review articles over a broader scope than is allowable in either journals or texts.
Download or read book Electro hydro dynamics Enhancement of Multiphase Heat Transfer in Pool Boiling written by Thai H. Nguyen and published by . This book was released on 2003 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Effect of Electrode Geometry on the Electrohydrodynamic Enhancement of Pool Boiling Heat Transfer of R123 oil Mixture written by Riyaz Amir Papar and published by . This book was released on 1993 with total page 194 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book High pressure Pool boiling Heat Transfer Enhancement and Mechanism on Engineered Surfaces written by Smreeti Dahariya and published by . This book was released on 2020 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Boiling has received considerable attention in the technology advancement of electronics cooling for high-performance computing applications. Two-phase cooling has an advantage over a single-phase cooling in the high heat removal rate with a small thermal gradient due to the latent heat of vaporization. Many surface modifications have been done in the past including surface roughness, mixed wettability and, porous wick copper play a crucial role in the liquid-vapor phase change heat transfer. However, the mechanisms of high-pressure pool-boiling heat transfer enhancement due to surface modifications has not been well studied or understood. The properties of water, such as the latent heat of vaporization, surface tension, the difference in specific volume of liquid and vapor, decrease at high-pressure. High-pressure pool-boiling heat transfer enhancement is studied fundamentally on various engineered surfaces. The boiling tests are performed at a maximum pressure of 90 psig (620.5 kPa) and then compared to results at 0 psig (0 kPa). The results indicate that the pressure influences the boiling performance through changes in bubble dynamics. The bubble departure diameter, bubble departure frequency, and the active nucleation sites change with pressure. The pool-boiling heat transfer enhancement of a Teflon© coated surface is also experimentally tested, using water as the working fluid. The boiling results are compared with a plain surface at two different pressures, 30 and 45 psig. The maximum heat transfer enhancement is found at the low heat fluxes. At high heat fluxes, a negligible effect is observed in HTC. The primary reasons for the HTC enhancement at low heat fluxes are active nucleation sites at low wall superheat and bubble departure size. The Teflon© coated surface promotes nucleation because of the lower surface energy requirement. The boiling results are also obtained for wick surfaces. The wick surfaces are fabricated using a sintering process. The boiling results are compared with a plain surface. The reasons for enhancements in the pool-boiling performance are primarily due to increased bubble generation, higher bubble release frequency, reduced thermal-hydraulic length modulation, and enhanced thermal conductivity due to the sintered wick layer. The analysis suggests that the Rayleigh-critical wavelength decreases by 4.67 % of varying pressure, which may cause the bubble pinning between the gaps of sintered particles and avoids the bubble coalescence. Changes in the pitch distance indicate that a liquid-vapor phase separation happens at the solid/liquid interface, which impacts the heat-transfer performance significantly. Similarly, the role of the high-pressure over the wicking layer is further analyzed and studied. It is found that the critical flow length, [lambda]u reduces by three times with 200 [mu]m particles. The results suggest that the porous wick layer provides a capillary-assist to liquid flow effect, and delays the surface dry out. The surface modification and the pressure amplify the boiling heat transfer performance. All these reasons may contribute to the CHF, and HTC enhancement in the wicking layer at high-pressure.
Download or read book Enhancement of Pool Boiling Heat Transfer in Confined Space written by Chia-Hsiang Hsu and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Pool boiling is an effective method used in many technical applications for a long time. Its highly efficient heat transfer performance results from not only the convection effect but also the phase change process in pool boiling. Pool boiling enhancement has been studied in the past decade. However, the mechanisms of pool boiling has not yet been fully understood because of the many parameters that affect its behavior including the latent heat of vaporization, nucleation density, bubble and fluid motion, interaction at the interface, and the physical properties of surface. Among the current studies, bubble departure rate is viewed as one of the dominant factors that affect heat transfer. This research considers the effect of bubble confinement on pool boiling. In the study, confinement was achieved by placing a flat plate over heated surface. The flat plate has a hole in the middle, and there is a gap between the flat plate and the heater. The diameters of hole are 2 mm, 3 mm, and 4 mm; the gap distances are 2.3 mm, 3.6 mm, and 5 mm. The heater consists of an indium-tin-oxide layer deposited on a silicon wafer. An IR camera and high speed cameras are used to acquire the surface temperature distribution and bubble image. By controlling the plate hole size and the gap distance, the effect of confinement on heat transfer performance can be evaluated. Moreover, heat transfer performance of pool boiling with three-2mm-holes plate was investigated and compared with that of single-2mm-hole plate with the smallest gap size. At the lower heat flux values, heat transfer enhancement in confined space was experimentally observed. Surface temperature can be reduced by 4 °C at most. Results indicate that higher bubble departure rate and coalescence effect might be the dominant factor for improving heat transfer performance in a confined space caused by induced shear flow. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/152843
Download or read book Proceedings of IEEE International Conference on Dielectric Liquids ICDL written by and published by . This book was released on 1999 with total page 726 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Enhancement of Pool Boiling Critical Heat Flux in Dielectric Liquids written by Mehmet Arik and published by . This book was released on 2001 with total page 462 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Pool Boiling Heat Transfer written by Dong Soo Jung and published by . This book was released on 1984 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Bubble Dynamics and Boiling Heat Transfer written by Samuel Siedel and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since boiling heat transfer affords a very effective means to transfer heat, it is implemented in numerous technologies and industries ranging from large power generation plants to micro-electronic thermal management. Although having been a subject of research for several decades, an accurate prediction of boiling heat transfer is still challenging due to the complexity of the coupled mechanisms involved. It appears that the boiling heat transfer coefficient is intimately related to bubble dynamics (i.e. bubble nucleation, growth and detachment) as well as factors such as nucleation site density and interaction between neighbouring and successive bubbles. In order to contribute to the understanding of the boiling phenomenon, an experimental investigation of saturated pool boiling from a single or two neighbouring artificial nucleation sites on a polished copper surface has been performed. The bubble growth dynamics has been characterized for different wall superheats and a experimental growth law has been established. The interaction between successive bubbles from the same nucleation site has been studied, showing the bubble shape oscillations that can be caused by these interactions. The forces acting on a growing bubble has been reviewed, and a complete momentum balance has been made for all stages of bubble growth. The curvature along the interface has been measured, and indications concerning the mechanism of bubble detachment have been suggested. The rise of bubble after detachment has been investigated, and the maximum velocity reached before a change of direction has been estimated and compared to existing models from the literature. The interaction between bubbles growing side by side has been studied: the generation and propagation of a wave front during the coalescence of two bubbles has been highlighted. As boiling heat transfer enhancement techniques are being imagined and developed, this study also focuses on the electrohydrodynamic enhancement technique. Boiling experiments have been performed in the presence of electric fields, and their effects on heat transfer and bubble dynamics have been characterized. Although the volume of the bubbles at detachment and the relationship between the bubble frequency and the wall superheat were not affected, the bubble growth curve was modified. The bubbles were elongated in the direction of the electric field, and this elongation was estimated and compared to other studies from the literature. The rising velocity of the bubble was reduced in the presence of electric field, and the behaviour of bubbles growing side by side was modified, the electric field causing the bubbles to repeal each other. These results, obtained in a fully controlled environment, provide compelling evidence that electric fields can be implemented to alter the bubble dynamics and subsequently heat transfer rates during boiling of dielectric fluids.
Download or read book Enhancement of Pool Boiling Heat Transfer Using a Combination of Open Microchannels and Microporous Surfaces written by Chinmay Patil and published by . This book was released on 2014 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book An Experimental Study of Sodium Pool Boiling Heat Transfer written by R. C. Noyes and published by . This book was released on 1962 with total page 42 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Enhanced Pool Boiling of Water with Open Microchannels Over Cylindrical Tubes written by Jeet S. Mehta and published by . This book was released on 2013 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Pool boiling is a stable and efficient method for transferring large quantities of heat. It is employed in a wide range of applications, including steam generation in boilers, petrochemical, pharmaceutical, cryogenic and many other industrial processes. The objective of this work was to investigate the augmentation in the boiling heat transfer rates with an array of open microchannels over a cylindrical tube. In order to develop high performance surfaces, rectangular and V-groove cross-sectional geometry microchannels were fabricated and tested over tubular test sections. These microchannels were manufactured in two configurations: circumferentially around the test section and axially along the length. The effects of the microchannel geometric parameters on pool boiling performance were studied under horizontal and vertical orientations. Twenty uniquely modified microchannel surfaces were designed, fabricated and tested. The best performance was obtained with a circumferential rectangular microchannel test section in the horizontal orientation. A maximum heat transfer coefficient of 129 kW/m2*K was achieved at a heat flux of 1095 kW/m2, while maintaining a wall superheat of 8.5 K. The overall enhancement factors obtained at the maximum heat flux condition, ranged between 1.9 and 3.4 in the horizontal orientation, and 2.1 and 3.1 in the vertical orientation. The critical heat flux for almost all the designed test surfaces was increased by a factor of at least 1.6 over a plain tube. Area normalized results indicated that factors other than area enhancement are responsible for augmenting the heat transfer performance. High-speed videography of bubbles nucleating, growing and departing from the heated surface was performed. The bubble behavior over these open microchannels was analyzed to understand the fundamental mechanism during pool boiling. The bubble interactions in and over the open microchannels, and the liquid rewetting phenomenon greatly influence the heat transfer performance for these surface."--Abstract.
Download or read book Experimental Investigation of Pool Boiling Heat Transfer Augmentation in R 123 Using the Electrohydrodynamic Technique and Its Long Term Effects written by Alok Kumar and published by . This book was released on 1994 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Electrohydrodynamic Pool Boiling Heat Transfer in Microgravity written by Charles Akira Murakami and published by . This book was released on 2004 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Enhancement of Pool Boiling Heat Transfer Using Thermally conductive Microporous Coating Techniques written by Joo Han Kim and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The present research is an experimental study of the enhancement of boiling heat transfer using microporous coating techniques. The current research is divided into four major phases. During the first phase, the effects of different metal particle sizes in the coating compound for thermally non-conductive microporous coating on pool boiling performance of refrigerants and water are investigated. The test surfaces were solid copper blocks with 1-cm2 base at atmospheric pressure in saturated FC-72, R-123, and water. Results showed that the surface treatment by non-conductive microporous coating significantly enhanced both nucleate boiling and critical heat flux of FC-72 and R-123. However, the enhancement of boiling performance for water was merely shown. In the second phase, thermally conductive microporous coatings to enhance boiling performance of water were developed. The first phase motivated efforts to fabricate microporous coatings with conducting binder options. The second phase was stemmed from an effort to combine the advantages of both a mixture batch type (inexpensive & easy process) and sintering/machining method (low thermal resistance of conduction). Two categories of surface treatment processes were considered in the current research. The first can be achieved by a chemical process, Multi-Staged Electroplating (MSE), which uses electricity in a chemical bath to deposit a microporous structure on the surface. The second is a soldering process, Multi-Temperature Soldering Process (MTSP), which binds the metal particles to generate optimum microporous cavities. Scanning Electron Microscope (SEM) and optical microscope images were obtained for thermally conductive microporous coated surfaces. During the third phase, the pool boiling performance of developed MSE and MTSP from second phase was confirmed for water. Results showed that the MSE and MTSP augmented the boiling performance not only for refrigerants but also for water significantly compared to non-conductive microporous coatings. Further investigation for possible future industrial applications of microporous coatings, such as indirect cooling for electronic chips, nanofluids for high power generation industries, and freezing problem of water, were conducted in the final phase.
