Download or read book Enhanced Analysis and Users Manual for Radial Inflow Turbine Conceptual Design Code Rtd written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-02 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modeling enhancements made to a radial-inflow turbine conceptual design code are documented in this report. A stator-endwall clearance-flow model was added for use with pivoting vanes. The rotor calculations were modified to account for swept blades and splitter blades. Stator and rotor trailing-edge losses and a vaneless-space loss were added to the loss model. Changes were made to the disk-friction and rotor-clearance loss calculations. The loss model was then calibrated based on experimental turbine performance. A complete description of code input and output along with sample cases are included in the report. Glassman, Arthur J. Unspecified Center NAG3-1165; RTOP 505-69-50...
Download or read book Enhanced Analysis and Users Manual for Radial inflow Turbine Conceptual Design Code RTD written by Arthur J. Glassman and published by . This book was released on 1995 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1995 with total page 548 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book 14th International Conference on Turbochargers and Turbocharging written by Institution of Mechanical Engineers and published by CRC Press. This book was released on 2020-09-30 with total page 390 pages. Available in PDF, EPUB and Kindle. Book excerpt: 14th International Conference on Turbochargers and Turbocharging addresses current and novel turbocharging system choices and components with a renewed emphasis to address the challenges posed by emission regulations and market trends. The contributions focus on the development of air management solutions and waste heat recovery ideas to support thermal propulsion systems leading to high thermal efficiency and low exhaust emissions. These can be in the form of internal combustion engines or other propulsion technologies (eg. Fuel cell) in both direct drive and hybridised configuration. 14th International Conference on Turbochargers and Turbocharging also provides a particular focus on turbochargers, superchargers, waste heat recovery turbines and related air managements components in both electrical and mechanical forms.
Download or read book Monthly Catalogue United States Public Documents written by and published by . This book was released on 1995 with total page 1638 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Monthly Catalog of United States Government Publications written by and published by . This book was released on 1995 with total page 854 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design Geometry and Design off design Performance Computer Codes for Compressors and Turbines written by and published by . This book was released on 1995 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Simulation Tools and Methods for Supercritical Carbon Dioxide Radial Inflow Turbine written by Jianhui Qi and published by Springer Nature. This book was released on 2023-01-01 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: To protect the Earth, China has launched its target of peaking carbon dioxide emissions by 2030, and achieving carbon neutrality by 2060 , which greatly encourages the use and development of renewable energy. Supercritical CO2 power cycle is a promising technology and the radial inflow turbine is the most important component of it, whose design and optimisation are considered as great challenges. This book introduces simulation tools and methods for supercritical CO2 radial inflow turbine, including a high fidelity quasi-one-dimensional design procedure, a non-ideal compressible fluid dynamics Riemann solver within open-source CFD software OpenFOAM framework, and a multi-objective Nelder–Mead geometry optimiser. Enhanced one-dimensional loss models are presented for providing a new insight towards the preliminary design of the supercritical CO2 radial inflow turbine. Since the flow phenomena within the blade channels are complex, involving fluid flow, shock wave transmission and boundary layer separation, only employing the ideal gas model is inadequate to predict the performance of the turbine. Thus, a non-ideal compressible fluid dynamics Riemann solver based on OpenFOAM library is developed. This book addresses the issues related to the turbine design and blade optimization and provides leading techniques. Hence, this book is of great value for the readers working on the supercritical CO2 radial inflow turbine and understanding the knowledge of CFD and turbomachinery.
Download or read book Government Reports Announcements Index written by and published by . This book was released on 1995 with total page 478 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Aeronautical Engineering A Cumulative Index to a Continuing Bibliography supplement 325 written by and published by . This book was released on 1995 with total page 470 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Gas Turbine Engineering Handbook written by Meherwan P. Boyce and published by Elsevier. This book was released on 2017-09-01 with total page 956 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Gas Turbine Engineering Handbook has been the standard for engineers involved in the design, selection, and operation of gas turbines. This revision includes new case histories, the latest techniques, and new designs to comply with recently passed legislation. By keeping the book up to date with new, emerging topics, Boyce ensures that this book will remain the standard and most widely used book in this field. The new Third Edition of the Gas Turbine Engineering Hand Book updates the book to cover the new generation of Advanced gas Turbines. It examines the benefit and some of the major problems that have been encountered by these new turbines. The book keeps abreast of the environmental changes and the industries answer to these new regulations. A new chapter on case histories has been added to enable the engineer in the field to keep abreast of problems that are being encountered and the solutions that have resulted in solving them. - Comprehensive treatment of Gas Turbines from Design to Operation and Maintenance. In depth treatment of Compressors with emphasis on surge, rotating stall, and choke; Combustors with emphasis on Dry Low NOx Combustors; and Turbines with emphasis on Metallurgy and new cooling schemes. An excellent introductory book for the student and field engineers - A special maintenance section dealing with the advanced gas turbines, and special diagnostic charts have been provided that will enable the reader to troubleshoot problems he encounters in the field - The third edition consists of many Case Histories of Gas Turbine problems. This should enable the field engineer to avoid some of these same generic problems
Download or read book Applied Engineering Principles Manual Training Manual NAVSEA written by Naval Sea Systems Command and published by . This book was released on 2019-07-15 with total page 454 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chapter 1 ELECTRICAL REVIEW 1.1 Fundamentals Of Electricity 1.2 Alternating Current Theory 1.3 Three-Phase Systems And Transformers 1.4 Generators 1.5 Motors 1.6 Motor Controllers 1.7 Electrical Safety 1.8 Storage Batteries 1.9 Electrical Measuring Instruments Chapter 2 ELECTRONICS REVIEW 2.1 Solid State Devices 2.2 Magnetic Amplifiers 2.3 Thermocouples 2.4 Resistance Thermometry 2.5 Nuclear Radiation Detectors 2.6 Nuclear Instrumentation Circuits 2.7 Differential Transformers 2.8 D-C Power Supplies 2.9 Digital Integrated Circuit Devices 2.10 Microprocessor-Based Computer Systems Chapter 3 REACTOR THEORY REVIEW 3.1 Basics 3.2 Stability Of The Nucleus 3.3 Reactions 3.4 Fission 3.5 Nuclear Reaction Cross Sections 3.6 Neutron Slowing Down 3.7 Thermal Equilibrium 3.8 Neutron Density, Flux, Reaction Rates, And Power 3.9 Slowing Down, Diffusion, And Migration Lengths 3.10 Neutron Life Cycle And The Six-Factor Formula 3.11 Buckling, Leakage, And Flux Shapes 3.12 Multiplication Factor 3.13 Temperature Coefficient...
Download or read book The Gas Turbine Handbook written by Tony Giampaolo and published by . This book was released on 2003 with total page 405 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Turbomachinery written by Marco Gambini and published by Springer Nature. This book was released on 2020-09-17 with total page 385 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a selection of preliminary sizing procedures for turbomachinery. Applicable to both conventional and non-conventional fluids, these procedures enable users to optimize the kinematics, thermodynamics and geometry of the turbomachinery (in the preliminary design phase) using geometric correlations and losses models; to accurately predict the efficiency of turbomachinery – in most cases, in excellent agreement with CFD calculations; and to consistently analyze all turbomachines (axial and radial turbines, axial and centrifugal compressors, centrifugal pumps). The book is intended for bachelor's and master's students in industrial, mechanical and energy engineering, as well as researchers and professionals in the energy systems and turbomachinery sectors, guiding them step by step through the first sizing of turbomachines and the verification of the technological feasibility of turbomachines designed for new conversion systems operating with unconventional fluids.
Download or read book Turbine Aerodynamics written by Ronald H. Aungier and published by American Society of Mechanical Engineers. This book was released on 2006 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a thorough description of actual, working aerodynamic design and analysis systems, for both axial-flow and radial-flow turbines. It describes the basic fluid dynamic and thermodynamic principles, empirical models and numerical methods used for the full range of procedures and analytical tools that an engineer needs for virtually any type of aerodynamic design or analysis activity for both types of turbine. The book includes sufficient detail for readers to implement all or part of the systems. The author provides practical and effective design strategies for applying both turbine types, which are illustrated by design examples. Comparisons with experimental results are included to demonstrate the prediction accuracy to be expected. This book is intended for practicing engineers concerned with the design and development of turbines and related machinery.
Download or read book Analytical Determination of Radial Inflow Turbine Design Geometry for Maximum Efficiency written by Harold E. Rohlik and published by . This book was released on 1968 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fluid Machinery and Fluid Mechanics written by Jianzhong Xu and published by Springer Science & Business Media. This book was released on 2010-07-05 with total page 445 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Fluid Machinery and Fluid Mechanics: 4th International Symposium (4th ISFMFE)" is the proceedings of 4th International Symposium on Fluid Machinery and Fluid Engineering, held in Beijing November 24-27, 2008. It contains 69 highly informative technical papers presented at the Mei Lecture session and the technical sessions of the symposium. The Chinese Society of Engineering Thermophysics (CSET) organized the First, the Second and the Third International Symposium on Fluid Machinery and Fluid Engineering (1996, 2000 and 2004). The purpose of the 4th Symposium is to provide a common forum for exchange of scientific and technical information worldwide on fluid machinery and fluid engineering for scientists and engineers. The main subject of this symposium is "Fluid Machinery for Energy Conservation". The "Mei Lecture" reports on the most recent developments of fluid machinery in commemoration of the late professor Mei Zuyan. The book is intended for researchers and engineers in fluid machinery and fluid engineering. Jianzhong Xu is a professor at the Chinese Society of Engineering Thermophysics, Chinese Academy of Sciences, Beijing.
