Download or read book Effect of Texture on Formability and Mechanical Anisotropy of a Severe Plastically Deformed Magnesium Alloy written by Sonia Modarres Razavi and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Magnesium and its alloys have been considered as alternatives to aluminum alloys and steels for structural applications in automotive and aerospace applications due to their superior specific strength and light-weight. However, they have hexagonal-close packed (hcp) structure, and thus have a small number of deformation systems resulting in low ductility and formability near room temperature, anisotropic thermo-mechanical response and strong deformation textures. The aim of this work is to investigate experimentally the effect of crystallographic texture generated during severe plastic deformation (SPD), on the subsequent formability and mechanical flow anisotropy in AZ31B Mg alloy. The proper control of grain size and texture through SPD is expected to result in better low temperature formability and better control of mechanical flow anisotropy. AZ31B Mg alloy has been successfully processed using equal channel angular extrusion (ECAE) following different processing routes, multiple passes, and different processing temperatures, in order to obtain samples with a wide variety of grain sizes, ranging from ~370 nm up to few microns, and crystallographic textures. Low temperature processing of the AZ31B Mg alloy was successful after initial high temperature processing. Smaller grain sizes were achieved using the temperature step-down method leading to incremental reduction in grain size at each ECAE pass. The temperature step-down method was utilized to develop hybrid ECAE routes to obtain specific crystallographic textures. Optimized hybrid ECAE routes were developed which resulted in a high strength/high ductility material with the average grain size of ~370 nm. The ECAE processed alloy showed a high tensile yield strength of ~380 MPa that has never been reported so far in AZ31 ingot metallurgy Mg alloys. The influence of grain size on the critical stress for the activation of individual deformation mechanisms was also investigated by systematically controlling the texture and grain size, and assuming the activation of mainly a single deformation mechanism through the careful selection of the loading direction on the processed samples. It was revealed that the Hall-Petch slope for the basal slip was much smaller than those of prismatic slip and tensile twinning.
Download or read book Magnesium written by Talal al- Samman and published by Cuvillier Verlag. This book was released on 2008 with total page 23 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Superplasticity in Metals and Ceramics written by T. G. Nieh and published by Cambridge University Press. This book was released on 1997-01-23 with total page 288 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes advances in the field of superplasticity, the ability of certain materials to undergo very large tensile strains. This phenomenon has increasing commercial applications, but also presents a fascinating scientific challenge in attempts to understand the physical mechanisms that underpin it. The authors emphasize the materials aspects of superplasticity. Beginning with a brief history of the phenomenon, they describe the two major types of superplasticity-- fine-structure and internal-stress superplasticity-- and discuss their operative mechanisms. They also present microstructural factors controlling the ductility and fracture in superplastic materials. Observations of superplasticity in metals (including aluminum, magnesium, iron, titanium and nickel), ceramics (including monoliths and composites), intermetallics (including iron, nickel, and titanium base), and laminates are thoroughly described. This is a valuable text for graduate students and researchers in materials science and engineering.
Download or read book Fundamentals of Magnesium Alloy Metallurgy written by Mihriban O Pekguleryuz and published by Elsevier. This book was released on 2013-03-11 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: Magnesium and magnesium alloys offer a wealth of valuable properties, making them of great interest for use across a wide range of fields. This has led to extensive research focused on understanding the properties of magnesium and how these can be controlled during processing. Fundamentals of magnesium alloy metallurgy presents an authoritative overview of all aspects of magnesium alloy metallurgy, including physical metallurgy, deformation, corrosion and applications.Beginning with an introduction to the primary production of magnesium, the book goes on to discuss physical metallurgy of magnesium and thermodynamic properties of magnesium alloys. Further chapters focus on understanding precipitation processes of magnesium alloys, alloying behaviour of magnesium, and alloy design. The formation, corrosion and surface finishing of magnesium and its alloys are reviewed, before Fundamentals of magnesium alloy metallurgy concludes by exploring applications across a range of fields. Aerospace, automotive and other structural applications of magnesium are considered, followed by magnesium-based metal matrix composites and the use of magnesium in medical applications.With its distinguished editors and international team of expert contributors, Fundamentals of magnesium alloy metallurgy is a comprehensive tool for all those involved in the production and application of magnesium and its alloys, including manufacturers, welders, heat-treatment and coating companies, engineers, metallurgists, researchers, designers and scientists working with these important materials. - Overviews all aspects of magnesium alloy metallurgy - Discusses physical metallurgy of magnesium and thermodynamic properties of magnesium alloys - Reviews the formation, corrosion and surface finishing of magnesium and its alloys
Download or read book Crystal Plasticity Finite Element Methods written by Franz Roters and published by John Wiley & Sons. This book was released on 2011-08-04 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by the leading experts in computational materials science, this handy reference concisely reviews the most important aspects of plasticity modeling: constitutive laws, phase transformations, texture methods, continuum approaches and damage mechanisms. As a result, it provides the knowledge needed to avoid failures in critical systems udner mechanical load. With its various application examples to micro- and macrostructure mechanics, this is an invaluable resource for mechanical engineers as well as for researchers wanting to improve on this method and extend its outreach.
Download or read book Magnesium written by Karl U. Kainer and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 1088 pages. Available in PDF, EPUB and Kindle. Book excerpt: The need for light-weight materials, especially in the automobile industry, created renewed interest in innovative applications of magnesium materials. This demand has resulted in increased research and development activity in companies and research institutes in order to achieve an improved property profile and better choice of alloy systems. Here, development trends and application potential in different fields like the automotive industry and communication technology are discussed in an interdisciplinary framework.
Download or read book Essential Readings in Magnesium Technology written by Suveen Mathaudhu and published by Springer. This book was released on 2016-12-06 with total page 609 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a compilation of the best papers in the history of Magnesium Technology, a definitive annual reference in the field of magnesium production and related light metals technologies. The volume contains a strong topical mix of application and fundamental research articles on magnesium technology. Section titles: 1.Magnesium Technology History and Overview 2.Electrolytic and Thermal Primary Production 3.Melting, Refining, Recycling, and Life-Cycle Analysis 4.Casting and Solidification 5.Alloy and Microstructural Design 6.Wrought Processing 7.Modeling and Simulation 8.Joining 9.Corrosion, Surface Treatment, and Coating
Download or read book Mechanical Flow Response and Anisotropy of Ultra fine Grained Magnesium and Zinc Alloys written by Majid H. Al Maharbi and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Hexagonal closed packed (hcp) materials, in contrast to cubic materials, possess several processing challenges due to their anisotropic structural response, the wide variety of deformation textures they exhibit, and limited ductility at room temperature. The aim of this work is to investigate, both experimentally and theoretically, the effect os severe plastic deformation, ultrafine grain sizes, crystallographic textures and number of phases on the flow stress anisotropy and tension compression asymmetry, and the mechanisms responsible for these phenomena in two hcp materials: AZ31B Mg alloy consisting of one phase and Zn-8wt.% Al that has an hcp matrix with a secondary facecentered cubic (fcc) phase. Mg and its alloys have high specific strength that can potentially meet the high demand for light weight structural materials and low fuelconsumption in transportation. Zn-Al alloys, on the other hand, can be potential substitutes for several ferrous and non-ferrous materials because of their good mechanical and tribological properties. Both alloys have been successfully processed using equal channel angular extrusion (ECAE) following different processing routes in order to produce samples with a wide variety of microstructures and crystallographic textures for revealing the relationship between microstructural parameters, crystallographic texture and resulting flow stress anisotropy at room temperature. For AZ31B Mg alloy, the texture evolution during ECAE following conventional and hybrid ECAE routes was successfully predicted using visco-plastic self-consistent (VPSC) crystal plasticity model. The flow stress anisotropy and tension-compression (T/C) asymmetry of the as received and processed samples at room temperature were measured and predicted using the same VPSC model coupled with a dislocation-based hardening scheme. The governing mechanisms behind these phenomena are revealed as functions of grains size and crystallographic texture. It was found that the variation in flow stress anisotropy and T/C asymmetry among samples can be explained based on the texture that is generated after each processing path. Therefore, it is possible to control the flow anisotropy and T/C asymmetry in this alloy and similar Mg alloys by controlling the processing route and number of passes, and the selection of processing conditions can be optimized using VPSC simulations. In Zn-8wt.% Al alloy, the hard phase size, morphology, and distribution were found to control the anisotropy in the flow strength and elongation to failure of the ECAE processed samples.
Download or read book Magnesium 2021 written by Alan Luo and published by Springer Nature. This book was released on 2021-05-28 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: This collection from the 12th International Conference on Magnesium Alloys and Their Applications (Mg 2021)—the longest running conference dedicated to the development of magnesium alloys—covers the breadth of magnesium research and development, from primary production to applications to end-of-life management. Authors from academia, government, and industry discuss new developments in magnesium alloys and share valuable insights. Topics in this volume include but are not limited to the following: Primary production Alloy development Solidification and casting processes Forming and thermo-mechanical processing Other manufacturing process development (including joining and additive manufacturing) Corrosion and protection Modeling and simulation Structural, functional, biomedical, and energy applications Advanced characterization and fundamental theories Recycling and environmental issues
Download or read book Magnesium Alloys Containing Rare Earth Metals written by L.L. Rokhlin and published by CRC Press. This book was released on 2003-02-20 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: Magnesium-based alloys containing rare-earth metals are important structural materials, as they combine low density with high-strength properties. This makes them particularly attractive for industry, especially in cases where the low weight of constructions is critical, as in aircraft and space apparatus construction. One of the remarkable feature
Download or read book Crystallographic Texture of Materials written by Satyam Suwas and published by Springer. This book was released on 2016-09-10 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing a comprehensive and invaluable overview of the basics of crystallographic textures and their industrial applications, this book covers a broad range of both structural and functional materials. It introduces the existing methods of representation in an accessible manner and presents a thorough overview of existing knowledge on texture of metallic materials. Texture analysis has widespread use in many industries, and provides crucial input towards the development of new materials and products. There has been rapid growth in the science and art of texture analysis in the last few decades. Other topics addressed within this book include recent research on texture in thin films and non-metals, and the dependence of material properties on texture, and texture control in some engineering materials. This book constitutes an invaluable reference text for researchers and professionals working on texture analysis in metallurgy, materials science and engineering, physics and geology. By using content selectively, it is also highly accessible to undergraduate students.
Download or read book Magnesium Technology 2019 written by Vineet V. Joshi and published by Springer. This book was released on 2019-02-14 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Magnesium Technology Symposium, the event on which this collection is based, is one of the largest yearly gatherings of magnesium specialists in the world. Papers represent all aspects of the field, ranging from primary production to applications to recycling. Moreover, papers explore everything from basic research findings to industrialization. Magnesium Technology 2019 covers a broad spectrum of current topics, including alloys and their properties; cast products and processing; wrought products and processing; forming, joining, and machining; corrosion and surface finishing; and structural applications. In addition, there is coverage of new and emerging applications.
Download or read book Severe Plastic Deformation written by Ghader Faraji and published by Elsevier. This book was released on 2018-07-14 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: Severe Plastic Deformation: Methods, Processing and Properties examines all severe plastic deformation techniques developed over the past two decades, exploring the appropriate severe plastic deformation method for a particular case. The book offers an overview of these methods, introduces ultrafine-grained and nano-grained metals and methods for various bulk, sheet, tubular and large size samples, reviews effective parameters to make a severe plastic deformation method better, from property (mechanical) and processing (cost, time, load, etc.) viewpoints, discusses mechanical, physical and chemical properties of UFG and NS metals, and concludes with various applications for these methods. Over the last several decades, a large number of severe plastic deformation methods have been developed for processing a wide array of metals for superior properties, making this a timely resource. Collects all severe plastic deformation methods in a unique reference Compares severe plastic deformation methods from several viewpoints, including processing and final property Classifies severe plastic deformation methods based on the sample shape and mechanics, as well as the properties achieved in the processed metal Introduces ultrafine-grained and nano-grained metals and methods for various bulk, sheet, tubular and large size samples
Download or read book Nanomaterials by Severe Plastic Deformation written by Michael J. Zehetbauer and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 872 pages. Available in PDF, EPUB and Kindle. Book excerpt: These proceedings of the "Second International Conference on Nanomaterials by Severe Plastic Deformation" review the enormous scientific avalanche that has been developing in the field over recent years. A valuable resource for any scientist and engineer working in this emerging field of nanotechnology.
Download or read book Titanium Alloys written by Jan Sieniawski and published by BoD – Books on Demand. This book was released on 2013-05-15 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book contains six chapters and covers topics dealing with biomedical applications of titanium alloys, surface treatment, relationships between microstructure and mechanical and technological properties, and the effect of radiation on the structure of the titanium alloys.
Download or read book Mechanical Behaviour of Engineering Materials written by Joachim Roesler and published by Springer Science & Business Media. This book was released on 2007-10-16 with total page 540 pages. Available in PDF, EPUB and Kindle. Book excerpt: How do engineering materials deform when bearing mechanical loads? To answer this crucial question, the book bridges the gap between continuum mechanics and materials science. The different kinds of material deformation are explained in detail. The book also discusses the physical processes occurring during the deformation of all classes of engineering materials and shows how these materials can be strengthened to meet the design requirements. It provides the knowledge needed in selecting the appropriate engineering material for a certain design problem. This book is both a valuable textbook and a useful reference for graduate students and practising engineers.
Download or read book Superplasticity in Advanced Materials ICSAM 2018 written by Goroh Itoh and published by Trans Tech Publications Ltd. This book was released on 2018-07-20 with total page 494 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume includes selected and peer reviewed papers presented at the 13th International Conference on Superplasticity in Advanced Materials (ICSAM 2018), August 19-22, 2018, St. Petersburg, Russia. We hope this collection will be interesting and useful for many specialists whose scientific and engineering activity is related to the area of superplastic materials, research of the mechanisms of superplasticity and superplastic processing technologies.
