Download or read book Effect of residual stresses on the fatigue crack propagation in welded joints written by Nenad Gubeljak and published by . This book was released on 2005 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: The effect of residual stress on the fatigue crack growth was investigated for cyclic tension. Three-point bend specimens were used with through thickness notches at the center line of the welded joint. The experiments were performed for different load amplitudes and load ratios under conditions of small-scale yielding. The influence of the residual stresses on fatigue crack growth was estimated by experimentally observed fatigue crack growth rate and measurement of residual stresses at the surface of specimen. This paper describes an approach taken in two models to estimate the residual stress effect on fatigue crack propagation and to predict remaining service life of a welded structure.
Download or read book Residual Stress Effects in Fatigue written by H. S. Reemsnyder and published by ASTM International. This book was released on 1982 with total page 244 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Residual Stress Effects in Fatigue written by and published by . This book was released on 1982 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Analysis of Welded Structures written by Koichi Masubuchi and published by Elsevier. This book was released on 2013-10-22 with total page 655 pages. Available in PDF, EPUB and Kindle. Book excerpt: Analysis of Welded Structures: Residual Stresses, Distortion, and their Consequences encompasses several topics related to design and fabrication of welded structures, particularly residual stresses and distortion, as well as their consequences. This book first introduces the subject by presenting the advantages and disadvantages of welded structures, as well as the historical overview of the topic and predicted trends. Then, this text considers residual stresses, heat flow, distortion, fracture toughness, and brittle and fatigue fractures of weldments. This selection concludes by discussing the effects of distortion and residual stresses on buckling strength of welded structures and effects of weld defects on service behavior. This book also provides supplementary discussions on some related and selected subjects. This text will be invaluable to metallurgists, welders, and students of metallurgy and welding.
Download or read book Fatigue of Welded Structures written by Timothy Russell Gurney and published by CUP Archive. This book was released on 1979-12-20 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fatigue Testing of Weldments written by D. W. Hoeppner and published by ASTM International. This book was released on 1978 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Fracture and Fatigue of Welded Joints and Structures written by K Macdonald and published by Elsevier. This book was released on 2011-04-19 with total page 353 pages. Available in PDF, EPUB and Kindle. Book excerpt: The failure of any welded joint is at best inconvenient and at worst can lead to catastrophic accidents. Fracture and fatigue of welded joints and structures analyses the processes and causes of fracture and fatigue, focusing on how the failure of welded joints and structures can be predicted and minimised in the design process.Part one concentrates on analysing fracture of welded joints and structures, with chapters on constraint-based fracture mechanics for predicting joint failure, fracture assessment methods and the use of fracture mechanics in the fatigue analysis of welded joints. In part two, the emphasis shifts to fatigue, and chapters focus on a variety of aspects of fatigue analysis including assessment of local stresses in welded joints, fatigue design rules for welded structures, k-nodes for offshore structures and modelling residual stresses in predicting the service life of structures.With its distinguished editor and international team of contributors, Fracture and fatigue of welded joints and structures is an essential reference for mechanical, structural and welding engineers, as well as those in the academic sector with a research interest in the field. - Analyses the processes and causes of fracture and fatigue, focusing predicting and minimising the failure of welded joints in the design process - Assesses the fracture of welded joints and structure featuring constraint-based fracture mechanics for predicting joint failure - Explores specific considerations in fatigue analysis including the assessment of local stresses in welded joints and fatigue design rules for welded structures
Download or read book Welding Deformation and Residual Stress Prevention written by Ninshu Ma and published by Elsevier. This book was released on 2012-04-26 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Generally, welding produces welding deformation and residual stress in the products, which influences the quality and performance of the products. Although many engineers and researchers have made great effort how to control these incidents, they have still remained unresolved. Welding Deformation and Residual Stress Prevention provides a unique computational approach to the prediction of the effects of deformation and residual stress on materials. The goal is to provide engineers and designers with the ability to create their own computational system for predicting and possibly avoiding the problem altogether. - The basic theories including "theory of elastic-plastic analysis" and "inherent strain theory" , and analysis procedures are described using a simple three-bar model - Online simulation software to perform basic analysis on welding mechanics - Examples of strategic methods and procedures are illustrated to have solved various welding-related problems encountered in the process of construction - Appendices present data bases for welding residual stresses, temperature dependent material properties, etc.
Download or read book Cumulative Damage of Welded Joints written by T R Gurney and published by Woodhead Publishing. This book was released on 2006-08-25 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue is a mechanism of failure which involves the formation and growth of cracks under the action of repeated stresses. Ultimately, a crack may propagate to such an extent that total fracture of the member may occur. To avoid fatigue it is essential to design the structure with inherent fatigue strength. However, fatigue strength for variable amplitude loading is not a constant material property and any calculations are necessarily built on a number of assumptions. Cumulative damage of welded joints explores the wealth of research in this important field and its implications for the design and manufacture of welded components.After an Introduction, chapter two introduces the constant amplitude database, which contains results obtained in test conditions and which forms the basis of the basic S-N curves for various types of joint. Chapter three discusses the influence of residual stresses which can have a marked effect on fatigue behaviour. Chapter four explores variable amplitude loading and the problem of how information from laboratory tests, obtained under constant amplitude conditions, can be applied to the design of structures for service conditions. This problem is further investigated in the next chapter which is devoted to two and three level load testing. Chapters six, seven and eight look at the influence that the variety of variable loading spectra can have on fatigue strength, whether narrow or wide band loading or cycles of small stress range. Taking all of this knowledge, chapter nine discusses structure designs.Cumulative damage of welded joints is a comprehensive source of invaluable information for welding engineers, supervisors, inspection personnel and designers. It will also be of great interest for academics working in the fields of structural and mechanical engineering. - Covers the wealth of research in the field of fatigue strength and its role in the design and manufacture of welded components - Invaluable reference source for welding engineers, supervisors, inspection personnel and designers
Download or read book Influence of Residual Stresses on Fatigue Crack Propagation in Electroslag Welds written by BM. Kapadia and published by . This book was released on 1978 with total page 17 pages. Available in PDF, EPUB and Kindle. Book excerpt: An investigation of fatigue crack propagation behavior in air of as-deposited electroslag welds in two hot-rolled structural steels, prepared according to ASTM Specification for Structural Steel (A 36) and ASTM Specification for High-Strength Low-Alloy Structural Steel with 50 000 psi Minimum Yield Point to 4 in. Thick (Grade A) (A 588), has shown that the crack-growth rates (da/dN) in the welds were similar to or up to five times slower than the rate in the base steels. The retardation in crack-growth rate was observed to be substantially greater for crack propagation in the coarse-grained heat-affected-zone (HAZ) and bond-line regions than in the weld metal, but this was not consistently observed. Moreover, marked variations in the microstructure of the weld metal and HAZ did not significantly influence crack propagation. These crack-growth data for the weldments, described in an earlier paper, have been analyzed in the present paper in terms of residual stresses causing the observed retardation in crack-growth rate. In the present work, quantitative comparisons of the crack-growth behavior of the welds were based on a cyclic-life parameter (N1), which was defined as the number of cycles required for precracking the IT wedge-opening-loading (WOL) specimens to a total crack length of 2.54 cm (1 in.). This parameter gave results that were consistent with those based on incremental crack-growth (da/dN) data in the earlier paper. The observed retardation in crack-growth rate in the welds is attributed to compressive residual stresses introduced by welding. This effect was analyzed in the present paper in terms of a stress-intensity-range suppression concept, whereby the applied stress-intensity-factor range is decreased to some lower effective value. The results showed that the beneficial effect of compressive residual stresses on crack propagation appears to be of a variable nature and would diminish following a stress-relief heat treatment.
Download or read book Tubular Structures XIII written by Ben Young and published by CRC Press. This book was released on 2010 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper presents a series of test results carried out on elliptical Concrete-Filled Tube (CFT) columns. The tests were conducted to investigate the effects of variations of concrete strength and column slenderness on the behaviour and axial strength of the columns. The experimental study was carried out on ten specimens of short and long columns with Self-Consolidating Concrete (SCC). One elliptical steel section was used with three different typical concrete strengths to determine the reduction of column strength with the increase in column length. All specimens were tested to failure to assess their load carrying capacity, deformation and structural behaviour.
Download or read book Springer Handbook of Experimental Solid Mechanics written by William N. Sharpe, Jr. and published by Springer Science & Business Media. This book was released on 2008-12-04 with total page 1100 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Springer Handbook of Experimental Solid Mechanics documents both the traditional techniques as well as the new methods for experimental studies of materials, components, and structures. The emergence of new materials and new disciplines, together with the escalating use of on- and off-line computers for rapid data processing and the combined use of experimental and numerical techniques have greatly expanded the capabilities of experimental mechanics. New exciting topics are included on biological materials, MEMS and NEMS, nanoindentation, digital photomechanics, photoacoustic characterization, and atomic force microscopy in experimental solid mechanics. Presenting complete instructions to various areas of experimental solid mechanics, guidance to detailed expositions in important references, and a description of state-of-the-art applications in important technical areas, this thoroughly revised and updated edition is an excellent reference to a widespread academic, industrial, and professional engineering audience.
Download or read book Fatigue of Structures and Materials written by J. Schijve and published by Springer Science & Business Media. This book was released on 2008-12-16 with total page 627 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fatigue of structures and materials covers a wide scope of different topics. The purpose of the present book is to explain these topics, to indicate how they can be analyzed, and how this can contribute to the designing of fatigue resistant structures and to prevent structural fatigue problems in service. Chapter 1 gives a general survey of the topic with brief comments on the signi?cance of the aspects involved. This serves as a kind of a program for the following chapters. The central issues in this book are predictions of fatigue properties and designing against fatigue. These objectives cannot be realized without a physical and mechanical understanding of all relevant conditions. In Chapter 2 the book starts with basic concepts of what happens in the material of a structure under cyclic loads. It illustrates the large number of variables which can affect fatigue properties and it provides the essential background knowledge for subsequent chapters. Different subjects are presented in the following main parts: • Basic chapters on fatigue properties and predictions (Chapters 2–8) • Load spectra and fatigue under variable-amplitude loading (Chapters 9–11) • Fatigue tests and scatter (Chapters 12 and 13) • Special fatigue conditions (Chapters 14–17) • Fatigue of joints and structures (Chapters 18–20) • Fiber-metal laminates (Chapter 21) Each chapter presents a discussion of a speci?c subject.
Download or read book Fatigue and Fracture Testing of Weldments written by Harry I. McHenry and published by ASTM International. This book was released on 1990 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fifteen papers from a symposium held in Sparks, Nev., April 1988. They cover: low and high cycle fatigue, fatigue crack growth, corrosion fatigue, fracture toughness testing, and wide-plate testing. Annotation copyright Book News, Inc. Portland, Or.
Download or read book Stress Determination for Fatigue Analysis of Welded Components written by E. Niemi and published by Woodhead Publishing. This book was released on 1995-04-30 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report introduces definitions of the terminology relevant to stress determination for fatigue analysis of welded components. The various stress concentrations, stress categories and fatigue analysis methods are defined. Fatigue analysis methods considered are nominal stress, hot spot stress, notch stress, notch strain and fracture mechanics approaches. The report also contains comprehensive recommendations concerning the application of finite element methods and experimental methods for stress determination. It is intended for fatigue design of common welded structures, such as cranes, excavators, vehicle frames, bridges, ship hulls, offshore structures etc. fabricated from materials at least 3mm thick. In general, attention is focused on weld details which give rise to fatigue cracking from the surface, notably from the weld toe.
Download or read book Fatigue Life Analyses of Welded Structures written by Tom Lassen and published by John Wiley & Sons. This book was released on 2013-03-01 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Avoiding or controlling fatigue damage is a major issue in the design and inspection of welded structures subjected to dynamic loading. Life predictions are usually used for safe life analysis, i.e. for verifying that it is very unlikely that fatigue damage will occur during the target service life of a structure. Damage tolerance analysis is used for predicting the behavior of a fatigue crack and for planning of in-service scheduled inspections. It should be a high probability that any cracks appearing are detected and repaired before they become critical. In both safe life analysis and the damage tolerance analysis there may be large uncertainties involved that have to be treated in a logical and consistent manner by stochastic modeling. This book focuses on fatigue life predictions and damage tolerance analysis of welded joints and is divided into three parts. The first part outlines the common practice used for safe life and damage tolerance analysis with reference to rules and regulations. The second part emphasises stochastic modeling and decision-making under uncertainty, while the final part is devoted to recent advances within fatigue research on welded joints. Industrial examples that are included are mainly dealing with offshore steel structures. Spreadsheets which accompany the book give the reader the possibility for hands-on experience of fatigue life predictions, crack growth analysis and inspection planning. As such, these different areas will be of use to engineers and researchers.
Download or read book Fatigue Strength of Welded Structures written by S J Maddox and published by Woodhead Publishing. This book was released on 2014-03-14 with total page 211 pages. Available in PDF, EPUB and Kindle. Book excerpt: The key to avoidance of fatigue, which is the main cause of service failures, is good design. In the case of welded joints, which are particularly susceptible to fatigue, design rules are available. However, their effective use requires a good understanding of fatigue and an appreciation of problems concerned with their practical application. Fatigue strength of welded structures has incorporates up-to-date design rules with high academic standards whilst still achieving a practical approach to the subject. The book presents design recommendations which are based largely on those contained in recent British standards and explains how they are applied in practice. Attention is also focused on the relevant aspects of fatigue in welded joints which are not yet incorporated in codes thus providing a comprehensive aid for engineers concerned with the design or assessment of welded components or structures. Background information is given on the fatigue lives of welded joints which will enable the engineer or student to appreciate why there is such a contrast between welded and unwelded parts, why some welded joints perform better than others and how joints can be selected to optimise fatigue performance.
