Download or read book Digital Signal Processing in Power Electronics Control Circuits written by Krzysztof Sozański and published by Springer Science & Business Media. This book was released on 2013-07-03 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

Download or read book Digital Signal Processing in Power Electronics Control Circuits written by Krzysztof Sozanski and published by Springer. This book was released on 2013-07-06 with total page 265 pages. Available in PDF, EPUB and Kindle. Book excerpt: Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

Download or read book Digital Signal Processing in Power Electronics Control Circuits written by Krzysztof Sozański and published by Springer. This book was released on 2017-05-10 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: This revised and extended second edition covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book discusses signal processing, starting from analog signal acquisition, through conversion to digital form, methods of filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing, a three-phase shunt active power filter and a digital class-D audio power amplifier. The book bridges the gap between power electronics and digital signal processing. Many control algorithms and circuits for power electronics in the current literature are described using analog transmittances. This may not always be acceptable, especially if half of the sampling frequencies and half of the power transistor switching frequencies are close to the band of interest. Therefore in this book, a digital circuit is treated as a digital circuit with its own peculiar characteristics, rather than an analog circuit. This helps to avoid errors and instability. This edition includes a new chapter dealing with selected problems of simulation of power electronics systems together with digital control circuits. The book includes numerous examples using MATLAB and PSIM programs.

Download or read book Programming and Application of a DSP to Control and Regulate Power Electronic Converters Programming in C written by Baris Bagci and published by diplom.de. This book was released on 2014-03-01 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this project has been to study, operate and program the 32-bit 150MIPS TMS320F2812 DSP developed by Texas Instruments Inc. In addition, it has also been a goal to implement fast estimation techniques for control of resonant converters. For this purpose, PWM signals that are generated using this DSP are used. The demands on the system and the hardware to solve the problem were already decided when I started the work. The algorithms were programmed in C/C++ language, compiled, debugged and transferred to the DSP development board in a compiling and simulation tool (downloader), called CCS (Code Composer Studio v2), also provided by Texas Instruments. In the first chapters of this study I give general information about control systems, digital signal processors, digital signal processing and the DSP used in this work. The following chapters tell about PWM, how to configure the PWM outputs and some examples related with PWM signals are given. After a short review of series resonant converters, I presented the last example implemented in this project. I conclude with a summary and provide some hints of future work.

Download or read book Digital Signal Processing in Power System Protection and Control written by Waldemar Rebizant and published by Springer Science & Business Media. This book was released on 2011-07-28 with total page 324 pages. Available in PDF, EPUB and Kindle. Book excerpt: Digital Signal Processing in Power System Protection and Control bridges the gap between the theory of protection and control and the practical applications of protection equipment. Understanding how protection functions is crucial not only for equipment developers and manufacturers, but also for their users who need to install, set and operate the protection devices in an appropriate manner. After introductory chapters related to protection technology and functions, Digital Signal Processing in Power System Protection and Control presents the digital algorithms for signal filtering, followed by measurement algorithms of the most commonly-used protection criteria values and decision-making methods in protective relays. A large part of the book is devoted to the basic theory and applications of artificial intelligence techniques for protection and control. Fuzzy logic based schemes, artificial neural networks, expert systems and genetic algorithms with their advantages and drawbacks are discussed. AI techniques are compared and it is also shown how they can be combined to eliminate the disadvantages and magnify the useful features of particular techniques. The information provided in Digital Signal Processing in Power System Protection and Control can be useful for protection engineers working in utilities at various levels of the electricity network, as well as for students of electrical engineering, especially electrical power engineering. It may also be helpful for other readers who want to get acquainted with and to apply the filtering, measuring and decision-making algorithms for purposes other than protection and control, everywhere fast and on-line signal analysis is needed for proper functioning of the apparatus.

Download or read book Control Circuits in Power Electronics written by Miguel Castilla and published by IET. This book was released on 2016-05-16 with total page 457 pages. Available in PDF, EPUB and Kindle. Book excerpt: Resource added for the Electronics/Biomedical Technology program 106051.

Download or read book Integrated Power Electronic Converters and Digital Control written by Ali Emadi and published by CRC Press. This book was released on 2017-12-19 with total page 350 pages. Available in PDF, EPUB and Kindle. Book excerpt: Because of the demand for higher efficiencies, smaller output ripple, and smaller converter size for modern power electronic systems, integrated power electronic converters could soon replace conventional switched-mode power supplies. Synthesized integrated converters and related digital control techniques address problems related to cost, space, flexibility, energy efficiency, and voltage regulation—the key factors in digital power management and implementation. Meeting the needs of professionals working in power electronics, as well as advanced engineering students, Integrated Power Electronic Converters and Digital Control explores the many benefits associated with integrated converters. This informative text details boost type, buck type, and buck-boost type integrated topologies, as well as other integrated structures. It discusses concepts behind their operation as well specific applications. Topics discussed include: Isolated DC-DC converters such as flyback, forward, push-pull, full-bridge, and half-bridge Power factor correction and its application Definition of the integrated switched-mode power supplies Steady-state analysis of the boost integrated flyback rectifier energy storage converter Dynamic analysis of the buck integrated forward converter Digital control based on the use of digital signal processors (DSPs) With innovations in digital control becoming ever more pervasive, system designers continue to introduce products that integrate digital power management and control integrated circuit solutions, both hybrid and pure digital. This detailed assessment of the latest advances in the field will help anyone working in power electronics and related industries stay ahead of the curve.

Download or read book Signal Processing and Analysis of Electrical Circuit written by Adam Glowacz and published by MDPI. This book was released on 2020-03-13 with total page 604 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Special Issue with 35 published articles shows the significance of the topic “Signal Processing and Analysis of Electrical Circuit”. This topic has been gaining increasing attention in recent times. The presented articles can be categorized into four different areas: signal processing and analysis methods of electrical circuits; electrical measurement technology; applications of signal processing of electrical equipment; fault diagnosis of electrical circuits. It is a fact that the development of electrical systems, signal processing methods, and circuits has been accelerating. Electronics applications related to electrical circuits and signal processing methods have gained noticeable attention in recent times. The methods of signal processing and electrical circuits are widely used by engineers and scientists all over the world. The constituent papers represent a significant contribution to electronics and present applications that can be used in industry. Further improvements to the presented approaches are required for realizing their full potential.

Download or read book Power Electronics and Motor Drives written by Bogdan M. Wilamowski and published by CRC Press. This book was released on 2018-10-03 with total page 1015 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Industrial Electronics Handbook, Second Edition combines traditional and newer, more specialized knowledge that will help industrial electronics engineers develop practical solutions for the design and implementation of high-power applications. Embracing the broad technological scope of the field, this collection explores fundamental areas, including analog and digital circuits, electronics, electromagnetic machines, signal processing, and industrial control and communications systems. It also facilitates the use of intelligent systems—such as neural networks, fuzzy systems, and evolutionary methods—in terms of a hierarchical structure that makes factory control and supervision more efficient by addressing the needs of all production components. Enhancing its value, this fully updated collection presents research and global trends as published in the IEEE Transactions on Industrial Electronics Journal, one of the largest and most respected publications in the field. Power Electronics and Motor Drives facilitates a necessary shift from low-power electronics to the high-power varieties used to control electromechanical systems and other industrial applications. This volume of the handbook: Focuses on special high-power semiconductor devices Describes various electrical machines and motors, their principles of operation, and their limitations Covers power conversion and the high-efficiency devices that perform the necessary switchover between AC and DC Explores very specialized electronic circuits for the efficient control of electric motors Details other applications of power electronics, aside from electric motors—including lighting, renewable energy conversion, and automotive electronics Addresses power electronics used in very-high-power electrical systems to transmit energy Other volumes in the set: Fundamentals of Industrial Electronics Control and Mechatronics Industrial Communication Systems Intelligent Systems

Download or read book Digital Power Electronics and Applications written by Fang Lin Luo and published by Elsevier. This book was released on 2010-07-20 with total page 422 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this book is to describe the theory of Digital Power Electronics and its applications. The authors apply digital control theory to power electronics in a manner thoroughly different from the traditional, analog control scheme. In order to apply digital control theory to power electronics, the authors define a number of new parameters, including the energy factor, pumping energy, stored energy, time constant, and damping time constant. These parameters differ from traditional parameters such as the power factor, power transfer efficiency, ripple factor, and total harmonic distortion. These new parameters result in the definition of new mathematical modeling: • A zero-order-hold (ZOH) is used to simulate all AC/DC rectifiers. • A first-order-hold (FOH) is used to simulate all DC/AC inverters. • A second-order-hold (SOH) is used to simulate all DC/DC converters. • A first-order-hold (FOH) is used to simulate all AC/AC (AC/DC/AC) converters. Presents most up-to-date methods of analysis and control algorithms for developing power electronic converters and power switching circuits Provides an invaluable reference for engineers designing power converters, commercial power supplies, control systems for motor drives, active filters, etc. Presents methods of analysis not available in other books

Download or read book Digital Control in Power Electronics written by Simone Buso and published by Springer Nature. This book was released on 2007-12-31 with total page 153 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the reader, whether an electrical engineering student in power electronics or a design engineer, some typical power converter control problems and their basic digital solutions, based on the most widespread digital control techniques. The presentation is focused on different applications of the same power converter topology, the half-bridge voltage source inverter, considered both in its single- and three-phase implementation. This is chosen as the case study because, besides being simple and well known, it allows the discussion of a significant spectrum of the more frequently encountered digital control applications in power electronics, from digital pulse width modulation (DPWM) and space vector modulation (SVM), to inverter output current and voltage control. The book aims to serve two purposes: to give a basic, introductory knowledge of the digital control techniques applied to power converters, and to raise the interest for discrete time control theory, stimulating new developments in its application to switching power converters.

Download or read book Control Techniques for Power Converters with Integrated Circuit written by Wen-Wei Chen and published by Springer. This book was released on 2017-12-28 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book offers an overview of power electronic applications in the study of power integrated circuit (IC) design, collecting novel research ideas and insights into fast transient response to prevent the output voltage from dropping significantly at the undershoot. It also discusses techniques and training to save energy and increase load efficiency, as well as fast transient response and high efficiency, which are the most important factors for consumer products that implement power IC. Lastly, the book focuses on power electronics for system loop analysis and optimal compensation design to help users and engineers implement their applications. The book is a valuable resource for university researchers, power IC R&D engineers, application engineers and graduate students in power electronics who wish to learn about the power IC design principles, methods, system behavior, and applications in consumer products.

Download or read book Digital Control in Power Electronics written by Simone Buso and published by Morgan & Claypool Publishers. This book was released on 2015-05-01 with total page 231 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the reader, whether an electrical engineering student in power electronics or a design engineer, a selection of power converter control problems and their basic digital solutions, based on the most widespread digital control techniques. The presentation is primarily focused on different applications of the same power converter topology, the half-bridge voltage source inverter, considered both in its single- and three-phase implementation. This is chosen as the test case because, besides being simple and well known, it allows the discussion of a significant spectrum of the most frequently encountered digital control applications in power electronics, from digital pulse width modulation (DPWM) and space vector modulation (SVM), to inverter output current and voltage control, ending with the relatively more complex VSI applications related to the so called smart-grid scenario. This book aims to serve two purposes: (1) to give a basic, introductory knowledge of the digital control techniques applied to power converters; and (2) to raise the interest for discrete time control theory, stimulating new developments in its application to switching power converters.

Download or read book Advanced Digital Signal Processing written by Glenn Zelniker and published by CRC Press. This book was released on 1993-10-28 with total page 694 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a detailed treatment of the concepts and applications of advanced digital signal processing.

Download or read book Real time Digital Signal Processing written by Sen-Maw Kuo and published by 清华大学出版社有限公司. This book was released on 2003 with total page 524 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Programming and Use of TMS320F2812 DSP to Control and Regulate Power Electronic Converters written by Baris Bagci and published by . This book was released on 2003 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt: Research to study, operate, and program the 32-bit 150MIPS TMS320F2812 digital signal processor (DSP) developed by Texas Instruments, Inc. In addition, it is an examination of the implementation of fast estimation techniques for control of resonant converters. For this purpose, pulse-width modulation (PWM) signals that are generated using this DSP are used.

Download or read book Control Circuits in Power Electronics written by Miguel Castilla and published by . This book was released on 2016 with total page 442 pages. Available in PDF, EPUB and Kindle. Book excerpt: Control circuits are a key element in the operation and performance of power electronics converters. This book describes practical issues related to the design and implementation of these control circuits, with a focus on the presentation of the state-of-the-art control solutions, including circuit technology, design techniques, and implementation issues. Topics covered include PWM-based sliding mode control schemes for DC-DC power converters; synthetic-ripple hysteretic controllers for DC/DC converters; one-cycle controlled single phase power inverters; digital PWM control of high-frequency DC-DC switched-mode power converters; microcontroller-based electronic ballasts for high-intensity-discharge lamps; FPGA-based controllers for direct sliding mode control of PWM boost rectifiers; DSP controllers for three-phase unity-power-factor rectifiers and voltage-sourced inverters; FPGADSP controllers for DC-DC converters in renewable energy applications; topologies, modulation and control of multilevel converters; state-of-the-art intelligent gate drivers for IGBT power modules; control of integrated switched capacitor power converters; DSP-based natural frame control schemes for three-phase unity-power-factor rectifiers; dual-core DSP for control and communication in AC microgrids; and the use of computational intelligence for designing power electronics converters. Control Circuits in Power Electronics is an essential reading for researchers, advanced students and practicing design engineers working in power electronics.