Download or read book Diesel Surrogate Fuels for Engine Testing and Chemical Kinetic Modeling written by and published by . This book was released on 2016 with total page 17 pages. Available in PDF, EPUB and Kindle. Book excerpt: The primary objectives of this work were to formulate, blend, and characterize a set of four ultra-low-sulfur diesel surrogate fuels in quantities sufficient to enable their study in single-cylinderengine and combustion-vessel experiments. The surrogate fuels feature increasing levels of compositional accuracy (i.e., increasing exactness in matching hydrocarbon structural characteristics) relative to the single target diesel fuel upon which the surrogate fuels are based. This approach was taken to assist in determining the minimum level of surrogate-fuel compositional accuracy that is required to adequately emulate the performance characteristics of the target fuel under different combustion modes. For each of the four surrogate fuels, an approximately 30-liter batch was blended, and a number of the physical and chemical properties were measured. Lastly, this publication documents the surrogate fuel creation process and the results of the property measurements.

Download or read book Progress in Chemical Kinetic Modeling for Surrogate Fuels written by and published by . This book was released on 2008 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: Gasoline, diesel, and other alternative transportation fuels contain hundreds to thousands of compounds. It is currently not possible to represent all these compounds in detailed chemical kinetic models. Instead, these fuels are represented by surrogate fuel models which contain a limited number of representative compounds. We have been extending the list of compounds for detailed chemical models that are available for use in fuel surrogate models. Detailed models for components with larger and more complicated fuel molecular structures are now available. These advancements are allowing a more accurate representation of practical and alternative fuels. We have developed detailed chemical kinetic models for fuels with higher molecular weight fuel molecules such as n-hexadecane (C16). Also, we can consider more complicated fuel molecular structures like cyclic alkanes and aromatics that are found in practical fuels. For alternative fuels, the capability to model large biodiesel fuels that have ester structures is becoming available. These newly addressed cyclic and ester structures in fuels profoundly affect the reaction rate of the fuel predicted by the model. Finally, these surrogate fuel models contain large numbers of species and reactions and must be reduced for use in multi-dimensional models for spark-ignition, HCCI and diesel engines.

Download or read book Recent Progress in the Development of Diesel Surrogate Fuels written by and published by . This book was released on 2009 with total page 37 pages. Available in PDF, EPUB and Kindle. Book excerpt: There has been much recent progress in the area of surrogate fuels for diesel. In the last few years, experiments and modeling have been performed on higher molecular weight components of relevance to diesel fuel such as n-hexadecane (n-cetane) and 2,2,4,4,6,8,8-heptamethylnonane (iso-cetane). Chemical kinetic models have been developed for all the n-alkanes up to 16 carbon atoms. Also, there has been much experimental and modeling work on lower molecular weight surrogate components such as n-decane and do-decane which are most relevant to jet fuel surrogates, but are also relevant to diesel surrogates where simulation of the full boiling point range is desired. For the cycloalkanes, experimental work on decalin and tetralin recently has been published. For multi-component surrogate fuel mixtures, recent work on modeling of these mixtures and comparisons to real diesel fuel is reviewed. Detailed chemical kinetic models for surrogate fuels are very large in size. Significant progress also has been made in improving the mechanism reduction tools that are needed to make these large models practicable in multidimensional reacting flow simulations of diesel combustion. Nevertheless, major research gaps remain. In the case of iso-alkanes, there are experiments and modeling work on only one of relevance to diesel: iso-cetane. Also, the iso-alkanes in diesel are lightly branched and no detailed chemical kinetic models or experimental investigations are available for such compounds. More components are needed to fill out the iso-alkane boiling point range. For the aromatic class of compounds, there has been no new work for compounds in the boiling point range of diesel. Most of the new work has been on alkyl aromatics that are of the range C7 to C8, below the C10 to C20 range that is needed. For the chemical class of cycloalkanes, experiments and modeling on higher molecular weight components are warranted. Finally for multi-component surrogates needed to treat real diesel, the inclusion of higher molecular weight components is needed in models and experimental investigations.

Download or read book Biologically Derived Diesel Fuel and No Formation written by Stephen Garner and published by . This book was released on 2011 with total page 438 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Chemistry of Diesel Fuels written by Chunsham Song and published by CRC Press. This book was released on 2020-08-08 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edited work covers diesel fuel chemistry in a systematic fashion from initial fuel production to the tail pipe exhaust. The chapters are written by leading experts in the research areas of analytical characterization of diesel fuel, fuel production and refining, catalysis in fuel processing, pollution minimization and control, and diesel fuel additives.

Download or read book Low temperature Combustion and Autoignition written by M.J. Pilling and published by Elsevier. This book was released on 1997-11-27 with total page 823 pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion has played a central role in the development of our civilization which it maintains today as its predominant source of energy. The aim of this book is to provide an understanding of both fundamental and applied aspects of low-temperature combustion chemistry and autoignition. The topic is rooted in classical observational science and has grown, through an increasing understanding of the linkage of the phenomenology to coupled chemical reactions, to quite profound advances in the chemical kinetics of both complex and elementary reactions. The driving force has been both the intrinsic interest of an old and intriguing phenomenon and the centrality of its applications to our economic prosperity. The volume provides a coherent view of the subject while, at the same time, each chapter is self-contained.

Download or read book Characterization and Properties of Petroleum Fractions written by M. R. Riazi and published by ASTM International. This book was released on 2005 with total page 425 pages. Available in PDF, EPUB and Kindle. Book excerpt: The last three chapters of this book deal with application of methods presented in previous chapters to estimate various thermodynamic, physical, and transport properties of petroleum fractions. In this chapter, various methods for prediction of physical and thermodynamic properties of pure hydrocarbons and their mixtures, petroleum fractions, crude oils, natural gases, and reservoir fluids are presented. As it was discussed in Chapters 5 and 6, properties of gases may be estimated more accurately than properties of liquids. Theoretical methods of Chapters 5 and 6 for estimation of thermophysical properties generally can be applied to both liquids and gases; however, more accurate properties can be predicted through empirical correlations particularly developed for liquids. When these correlations are developed with some theoretical basis, they are more accurate and have wider range of applications. In this chapter some of these semitheoretical correlations are presented. Methods presented in Chapters 5 and 6 can be used to estimate properties such as density, enthalpy, heat capacity, heat of vaporization, and vapor pressure. Characterization methods of Chapters 2-4 are used to determine the input parameters needed for various predictive methods. One important part of this chapter is prediction of vapor pressure that is needed for vapor-liquid equilibrium calculations of Chapter 9.

Download or read book The Development of a Detailed Chemical Kinetic Mechanism for Diisobutylene and Comparison to Shock Tube Ignition Times written by and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: There is much demand for chemical kinetic models to represent practical fuels such as gasoline, diesel and aviation fuel. These blended fuels contain hundreds of components whose identity and amounts are often unknown. A chemical kinetic mechanism that would represent the oxidation of all these species with accompanying chemical reactions is intractable with current computational capabilities, chemical knowledge and manpower resources. The use of surrogate fuels is an approach to make the development of chemical kinetic mechanisms for practical fuels tractable. A surrogate fuel model consists of a small number of fuel components that can be used to represent the practical fuel and still predict desired characteristics of the practical fuel. These desired fuel characteristics may include ignition behavior, burning velocity, fuel viscosity, fuel vaporization, and fuel emissions (carbon monoxide, hydrocarbons, soot and nitric oxides). Gasoline consists of many different classes of hydrocarbons including n-alkanes, alkenes, iso-alkanes, cycloalkanes, cycloalkenes, and aromatics. One approach is to use a fuel surrogate that has a single component from each class of hydrocarbon in gasoline so that the unique molecular structure of each class is represented. This approach may lead to reliable predictions of many of the combustion properties of the practical fuel. In order to obtain a fuel surrogate mechanism, detailed chemical kinetic mechanisms must be developed for each component in the surrogate. In this study, a detailed chemical kinetic mechanism is developed for diisobutylene, a fuel intended to represent alkenes in practical fuels such as gasoline, diesel, and aviation fuel. The fuel component diisobutylene usually consists of a mixture of two conjugate olefins of iso-octane: 1- or 2-pentene, 2,4,4-trimethyl. Diisobutylene has a similar molecular structure to iso-octane, so that its kinetics offers insight into the effect of including a double bond in the carbon skeletal structure of iso-octane. There are few previous studies on diisobutylene. Kaiser et al. [1] examined the exhaust emission from a production spark ignition engine with neat diisobutylene and with it mixed with gasoline. They found the exhaust emissions of diisobutylene to be similar to that of iso-octane. They saw a significant increase in the amount of 2-methyl-1,3-butadiene measured in the exhaust of the engine. They also found appreciable amount of propene in the exhaust, but could not explain the source of this product as they did others in terms of C-C bond beta scission of alkyl radicals. Risberg et al. [2] studied a number of fuel blends to evaluate their autoignition quality for use in a homogeneous charge compression ignition engine, using diisobutylene to represent olefins in one of their test fuels. In this study, experiments on the shock tube ignition of both isomers of diisobutylene will be described. Then, the development of a detailed chemical kinetic mechanism for the two isomers of diisobutylene will be discussed.

Download or read book Methodology for Formulating Diesel Surrogate Fuels with Accurate Compositional Ignition Quality and Volatility Characteristics written by and published by . This book was released on 2012 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this study, a novel approach was developed to formulate surrogate fuels having characteristics that are representative of diesel fuels produced from real-world refinery streams. Because diesel fuels typically consist of hundreds of compounds, it is difficult to conclusively determine the effects of fuel composition on combustion properties. Surrogate fuels, being simpler representations of these practical fuels, are of interest because they can provide a better understanding of fundamental fuel-composition and property effects on combustion and emissions-formation processes in internal-combustion engines. In addition, the application of surrogate fuels in numerical simulations with accurate vaporization, mixing, and combustion models could revolutionize future engine designs by enabling computational optimization for evolving real fuels. Dependable computational design would not only improve engine function, it would do so at significant cost savings relative to current optimization strategies that rely on physical testing of hardware prototypes. The approach in this study utilized the state-of-the-art techniques of 13C and 1H nuclear magnetic resonance spectroscopy and the advanced distillation curve to characterize fuel composition and volatility, respectively. The ignition quality was quantified by the derived cetane number. Two well-characterized, ultra-low-sulfur #2 diesel reference fuels produced from refinery streams were used as target fuels: a 2007 emissions certification fuel and a Coordinating Research Council (CRC) Fuels for Advanced Combustion Engines (FACE) diesel fuel. A surrogate was created for each target fuel by blending eight pure compounds. The known carbon bond types within the pure compounds, as well as models for the ignition qualities and volatilities of their mixtures, were used in a multiproperty regression algorithm to determine optimal surrogate formulations. The predicted and measured surrogate-fuel properties were quantitatively compared to the measured target-fuel properties, and good agreement was found.

Download or read book Handbook of Biofuels Production written by Rafael Luque and published by Woodhead Publishing. This book was released on 2022-12-05 with total page 618 pages. Available in PDF, EPUB and Kindle. Book excerpt: Handbook of Biofuels Production: Processes and Technologies, Third Edition provides a comprehensive and systematic reference on a range of biomass conversion processes and technologies. In response to the global increase in the use of biofuels as substitute transportation fuels, advanced chemical, biochemical and thermochemical biofuels production routes are quickly being developed. Substantial additions for this new edition include increased coverage of emerging feedstocks, including microalgae, more emphasis on by-product valorization for biofuels’ production, additional chapters on emerging biofuel production methods, and co-production of biofuels and bioproducts. The book's editorial team is strengthened by the addition of an extra member, and a number of new contributors have been invited to work with authors from the first and second edition to revise existing chapters, with each offering fresh perspectives. This book is an essential reference for professional engineers in the biofuel industry as well as researchers in academia, from post-graduate level and up. Provides systematic and detailed coverage of the processes and technologies being used in the production of first, second and third generation biofuels Evaluates the latest advanced chemical, biochemical and thermochemical technologies, processes and production routes Takes an integrated biorefinery approach, guiding readers through the production of biofuels and their co-products in integrated biorefineries Includes videos of industrial production facilities and equipment, showing how complex processes and reaction apparatus work in a lab and industry setting

Download or read book Thermodynamic and Transport Properties written by Claus Borgnakke and published by . This book was released on 1997-03-10 with total page 272 pages. Available in PDF, EPUB and Kindle. Book excerpt: Thermodynamic and Transport Properties This paperback book/disk set provides a comprehensive collection of thermodynamic tables and transportation properties in an easily accessible format. Featuring both English and SI units, the program features new substances such as the latest refrigerants and fuels. A variety of combinations of properties can be used as input for the disk calculations. This easy-to-use, mouse-driven program offers graphing and printing capabilities. This Outstanding Resource: Features full thermodynamic tables for 25 substances including: water, various refrigerants, cryogenic fluids, and hydrocarbons. Tables include numerical values for equation of state constants and virial coefficients. Highlights transport properties for a variety of gases, liquids, and solids. Covers new substances, such as refrigerants (R-134a, R-123, and R-152a) and fuels (methane, ethane, and ethylene). Contains ideal gas tables with thermochemical properties and equilibrium constants. Includes tables with numerical values for equation of state constants and virial coefficients. Minimum Hardware Requirements: IBM compatible 386 (486 DX or better recommended) VGA graphics Windows 3.1 or later 4 MB RAM 5 MB of available disk space

Download or read book Review of the 21st Century Truck Partnership written by National Research Council and published by National Academies Press. This book was released on 2008-10-19 with total page 130 pages. Available in PDF, EPUB and Kindle. Book excerpt: The 21st Century Truck Partnership (21CTP), a cooperative research and development partnership formed by four federal agencies with 15 industrial partners, was launched in the year 2000 with high hopes that it would dramatically advance the technologies used in trucks and buses, yielding a cleaner, safer, more efficient generation of vehicles. Review of the 21st Century Truck Partnership critically examines and comments on the overall adequacy and balance of the 21CTP. The book reviews how well the program has accomplished its goals, evaluates progress in the program, and makes recommendations to improve the likelihood of the Partnership meeting its goals. Key recommendations of the book include that the 21CTP should be continued, but the future program should be revised and better balanced. A clearer goal setting strategy should be developed, and the goals should be clearly stated in measurable engineering terms and reviewed periodically so as to be based on the available funds.

Download or read book Gasoline Compression Ignition Technology written by Gautam Kalghatgi and published by Springer Nature. This book was released on 2022-01-17 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on gasoline compression ignition (GCI) which offers the prospect of engines with high efficiency and low exhaust emissions at a lower cost. A GCI engine is a compression ignition (CI) engine which is run on gasoline-like fuels (even on low-octane gasoline), making it significantly easier to control particulates and NOx but with high efficiency. The state of the art development to make GCI combustion feasible on practical vehicles is highlighted, e.g., on overcoming problems on cold start, high-pressure rise rates at high loads, transients, and HC and CO emissions. This book will be a useful guide to those in academia and industry.

Download or read book Diesel Fuel Oils written by and published by . This book was released on 1960 with total page 512 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Cleaner Combustion written by Frédérique Battin-Leclerc and published by Springer Science & Business Media. This book was released on 2013-09-06 with total page 657 pages. Available in PDF, EPUB and Kindle. Book excerpt: This overview compiles the on-going research in Europe to enlarge and deepen the understanding of the reaction mechanisms and pathways associated with the combustion of an increased range of fuels. Focus is given to the formation of a large number of hazardous minor pollutants and the inability of current combustion models to predict the formation of minor products such as alkenes, dienes, aromatics, aldehydes and soot nano-particles which have a deleterious impact on both the environment and on human health. Cleaner Combustion describes, at a fundamental level, the reactive chemistry of minor pollutants within extensively validated detailed mechanisms for traditional fuels, but also innovative surrogates, describing the complex chemistry of new environmentally important bio-fuels. Divided into five sections, a broad yet detailed coverage of related research is provided. Beginning with the development of detailed kinetic mechanisms, chapters go on to explore techniques to obtain reliable experimental data, soot and polycyclic aromatic hydrocarbons, mechanism reduction and uncertainty analysis, and elementary reactions. This comprehensive coverage of current research provides a solid foundation for researchers, managers, policy makers and industry operators working in or developing this innovative and globally relevant field.

Download or read book Hcci and Cai Engines for the Automotive Industry written by H Zhao and published by Elsevier. This book was released on 2007-08-02 with total page 557 pages. Available in PDF, EPUB and Kindle. Book excerpt: Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality.HCCI and CAI engines for the automotive industry presents the state-of-the-art in research and development on an international basis, as a one-stop reference work. The background to the development of HCCI / CAI engine technology is described. Basic principles, the technologies and their potential applications, strengths and weaknesses, as well as likely future trends and sources of further information are reviewed in the areas of gasoline HCCI / CAI engines; diesel HCCI engines; HCCI / CAI engines with alternative fuels; and advanced modelling and experimental techniques. The book provides an invaluable source of information for scientific researchers, R&D engineers and managers in the automotive engineering industry worldwide. Presents the state-of-the-art in research and development on an international basis An invaluable source of information for scientific researchers, R&D engineers and managers in the automotive engineering industry worldwide Looks at one of the most promising engine technologies around

Download or read book Thermodynamic Models for Industrial Applications written by Georgios M. Kontogeorgis and published by John Wiley & Sons. This book was released on 2009-12-01 with total page 710 pages. Available in PDF, EPUB and Kindle. Book excerpt: Using an applications perspective Thermodynamic Models for Industrial Applications provides a unified framework for the development of various thermodynamic models, ranging from the classical models to some of the most advanced ones. Among these are the Cubic Plus Association Equation of State (CPA EoS) and the Perturbed Chain Statistical Association Fluid Theory (PC-SAFT). These two advanced models are already in widespread use in industry and academia, especially within the oil and gas, chemical and polymer industries. Presenting both classical models such as the Cubic Equations of State and more advanced models such as the CPA, this book provides the critical starting point for choosing the most appropriate calculation method for accurate process simulations. Written by two of the developers of these models, Thermodynamic Models for Industrial Applications emphasizes model selection and model development and includes a useful “which model for which application” guide. It also covers industrial requirements as well as discusses the challenges of thermodynamics in the 21st Century.