Download or read book Design Information on PH 15 7 Mo Stainless Steel for Aircraft and Missiles written by R. J. Favor and published by . This book was released on 1960 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design Information on 17 7 PH Stainless Steel for Aircraft and Missiles written by R. J. Favor and published by . This book was released on 1960 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design Information on AM 350 Stainless Steel for Aircraft and Missiles written by R. J. Favor and published by . This book was released on 1961 with total page 58 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Mechanical Properties of the 18 Per Cent Nickel Maraging Steels written by J. E. Campbell and published by . This book was released on 1964 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since the combination of tensile properties and toughness that can be obtained with the maraging steels is higher than can be achieved with other steels by simple heat treatments, there is considerable interest in using the maraging steels for critical components such as rocket motor cases, pressure vessels, and aircraft forgings. This report includes information on the tensile, compressive, shear, bearing, dynamic modulus, impact, bend, fatigue, creep, and rupture properties of the 18 per cent nickel maraging steels and on the effect of temperature on these properties. Data for the properties of sheet, bar, and forgings, as well as data illustrating the effect of cold rolling, variation in the heat treatment, and elevated-temperature exposure also are presented. Data on the effect of specimen orientation, which are also included, indicate that the ductility and toughness of specimens designed to evaluate the properties in the short transverse direction are somewhat lower than in the other directions. The high strength and toughness that can be obtained in the 18 per cent nickel maraging steels make them attractive for certain critical applications that require these properties. The fabrication characteristics, weldability, and simple heat treatment are other advantages of these steels. (Author).
Download or read book Environmental and Metallurgical Factors of Stress corrosion Cracking in High strength Steels written by C. J. Slunder and published by . This book was released on 1961 with total page 50 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Titanium alloy Forgings written by H. J. Henning and published by . This book was released on 1960 with total page 96 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book The Application of High Pressure in Metal deformation Processing written by F. W. Boulger and published by . This book was released on 1964 with total page 82 pages. Available in PDF, EPUB and Kindle. Book excerpt: On October 3, 1963, a symposium was sponsored by the Bureau of Naval Weapons, Metalworking Processes and Equipment Program, on the application of high pressure in metal-deformation processing. Past research has shown that superimposed hydrostatic pressure can significantly increase the ductility at fracture of various materials. These observations have stimulated considerable interest in applying this hydrostatic-pressure effect to metal deformation processing, where it was anticipated that improved ductility and fabricability of brittle materials could be realized. Hydrostatic extrusion and hydrodynamic compressive forging were two such fabrication techniques discussed at the symposium, and preliminary results were found to be encouraging. Another fabrication process that will be investigated in the near future is sheet drawing, where the effect of superimposed pressure improves the ductility to fracture, it was noted that pressure cycling did not improve either the strength or ductility of steels containing various amounts of carbon. In addition to the mechanical-property effects, hydrostatic pressure has been found to affect measurably, numerous metallurgical properties of metals and alloys. (Author).
Download or read book The Engineering Properties of Tungsten and Tungsten Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 154 pages. Available in PDF, EPUB and Kindle. Book excerpt: The results of a state-of-the-art survey covering tungsten and ten of its alloys are presented. All data are given in tabular and graphical form covering some of the more important physical, mechanical, and metallurgical properties for each material. References are given at the conclusion of each material section.
Download or read book Physical Metallurgy of Nickel base Superalloys written by C. H. Lund and published by . This book was released on 1961 with total page 54 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Review of Current Data on the Tensile Properties of Metals at Very Low Temperatures written by James Edward Campbell and published by . This book was released on 1961 with total page 90 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Binary and Ternary Phase Diagrams of Columbium Molybdenum Tantalum and Tungsten written by J. J. English and published by . This book was released on 1961 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Oxidation of Tungsten written by Vincent David Barth and published by . This book was released on 1961 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: The report presents a detailed review of available information on the oxidation of W and its alloys. W is relatively inert below 700 C. As the temperature is increased above this level, however, oxidation becomes progressively more rapid, reaching catastrophic rates at temperatures around 1200 C and above. Various theories for the mechanism and rates of W oxidation at different temperatures are reviewed, and the effect of pressure and water vapor on the stability of W oxides is discussed in detail. The elevatedtemperature reactions of W with other materials, such as refractory oxides, and with gases other than oxygen also are covered. Information on the protection of W by alloying and coating is included. (Author).
Download or read book A Discussion of the Physical Metallurgy of the 18 Per Cent Nickel Maraging Steels written by Albert M. Hall and published by . This book was released on 1963 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: Various aspects of the physical metallurgy of the 18 % nickel maraging steels are discussed in this report in the light of the knowledge which has thus far been accumulated on these steels. The 18 % nickel type of maraging steel was singled out for discussion because of its especially attractive combination of strength and fracture toughness, the comparative simplicity with which it can be hardened, and the relative ease with which it can be formed and joined. The highnickel maraging steels are considered to be outstanding members of a loose-knit family of agehardenable or precipitation-hardenable martensitic steels. Some comparisons and analogies are drawn among various members of this family with particular reference to the 18% nickel steels. (Author).
Download or read book The Physical Metallurgy of Cobalt base Superalloys written by H J Wagner and published by . This book was released on 1962 with total page 102 pages. Available in PDF, EPUB and Kindle. Book excerpt: A detailed picture is presented of the physical and chemical phenomena that affect the behavior of cobalt-base superalloys. Solid-solution strengthening is obtained from the high-melting metallic elements molybdenum, tungsten, tantalum, and columbium. These elements also participate in precipitation reactions involving their carbides. Precipitation of intermetallic compounds such as Ni3Ti is an important process in cobalt alloys containing appreciable amounts of nickel and titanium. The relationships among microstructure, heat treatment, and mechanical properties of the important commercial alloys are considered, and whenever possible, explained on the basis of the physical and chem cal processes that occur. (Author).
Download or read book The Engineering Properties of Columbium and Columbium Alloys written by F. F. Schmidt and published by . This book was released on 1963 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: The results of a state-of-the-art survey covering niobium and 18 of its most promising alloys are presented. All data are given in tabular and graphical form covering some of the more important physical, mechanical, and metallurgical properties for each material. References are given at the conclusion of each material section.
Download or read book Brazing for High temperature Service written by H. E. Pattee and published by . This book was released on 1961 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Properties of Coated Refractory Metals written by W. A. Gibeaut and published by . This book was released on 1964 with total page 104 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report summarizes the information generated since the middle of 1961 on the chemical, physical, and mechanical properties of refractory metals that are coated with oxidation-resistant coatings of advanced-experimental or commercial status. It is a supplement to DMIC Report 162, Coatings for the Protection of Refractory Metals from Oxidation, dated November 24, 1961. Recent data on specific silicide- and aluminide- type coatings for columbium, molybdenum, tantalum, and tungsten and their alloys reflect general advances in coating quality and performance, understanding of the behavior of coated systems, and more complete realization of the problems associated with the use of coated hardware.
