Download or read book AASHTO Guide Specifications for LRFD Seismic Bridge Design written by and published by AASHTO. This book was released on 2009 with total page 249 pages. Available in PDF, EPUB and Kindle. Book excerpt: Covers seismic design for typical bridge types and applies to non-critical and non-essential bridges. Approved as an alternate to the seismic provisions in the AASHTO LRFD Bridge Design Specifications. Differs from the current procedures in the LRFD Specifications in the use of displacement-based design procedures, instead of the traditional force-based "R-Factor" method. Includes detailed guidance and commentary on earthquake resisting elements and systems, global design strategies, demand modeling, capacity calculation, and liquefaction effects. Capacity design procedures underpin the Guide Specifications' methodology; includes prescriptive detailing for plastic hinging regions and design requirements for capacity protection of those elements that should not experience damage.
Download or read book Design Guide for Pile Caps AASHTO written by Timothy Mays and published by . This book was released on 2018-06 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Building Code Requirements for Structural Concrete ACI 318 05 and Commentary ACI 318R 05 written by ACI Committee 318 and published by American Concrete Institute. This book was released on 2005 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Design of Pile Foundations written by Aleksandar Sedmak Vesić and published by Transportation Research Board. This book was released on 1977-01-01 with total page 68 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Examples for the Design of Structural Concrete with Strut and tie Models written by American Concrete Institute. Convention and published by . This book was released on 2002 with total page 264 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Prepared by members of ACI Subcommittee 445-1, Strut and Tie Models, for sessions at the Fall Convention in Phoenix, October 27 to November 1, 2002, and sponsored by Joint ACI-ASCE Committee 445, Shear and Torsion and ACI Committee 318-E, Shear and Torsion."
Download or read book Pile Design and Construction Practice Fifth Edition written by Michael Tomlinson and published by CRC Press. This book was released on 2007-12-06 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: This international handbook is essential for geotechnical engineers and engineering geologists responsible for designing and constructing piled foundations. It explains general principles and practice and details current types of pile, piling equipment and methods. It includes calculations of the resistance of piles to compressive loads, pile groups under compressive loading, piled foundations for resisting uplift and lateral loading and the structural design of piles and pile groups. Marine structures, miscellaneous problems (including machinery foundations, underpinning, mining subsidence areas, contracts and frozen ground), durability of piled foundations, ground investigations, and pile testing are also covered. It introduces the 2005 version of Eurocode7, BS 8004 and other codes, and refers to BS 6349 on maritime structures, and new forms of civil engineering contracts suitable for piling projects. It includes numerous worked examples to the codes, many based on actual problems. It also gives very comprehensive information for students.
Download or read book LRFD Guide Specifications for the Design of Pedestrian Bridges written by American Association of State Highway and Transportation Officials and published by AASHTO. This book was released on 2009 with total page 38 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of Italian Concrete Days 2018 written by Marco di Prisco and published by Springer Nature. This book was released on 2019-09-04 with total page 608 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gathers the best peer-reviewed papers presented at the Italian Concrete Days national conference, held in Lecco, Italy, on June 14-15, 2018. The conference topics encompass the aspects of design, execution, rehabilitation and control of concrete structures, with particular reference to theory and modeling, applications and realizations, materials and investigations, technology and construction techniques. The contributions amply demonstrate that today’s structural concrete applications concern not only new constructions, but more and more rehabilitation, conservation, strengthening and seismic upgrading of existing premises, and that requirements cover new aspects within the frame of sustainability, including environmental friendliness, durability, adaptability and reuse of works and / or materials. As such the book represents an invaluable, up-to-the-minute tool, providing an essential overview of structural concrete, as well as all new materials with cementitious matrices.
Download or read book Basics of Foundation Design written by Bengt Fellenius and published by Lulu.com. This book was released on 2017-03-17 with total page 488 pages. Available in PDF, EPUB and Kindle. Book excerpt: The "Red Book" presents a background to conventional foundation analysis and design. The text is not intended to replace the much more comprehensive 'standard' textbooks, but rather to support and augment these in a few important areas, supplying methods applicable to practical cases handled daily by practising engineers and providing the basic soil mechanics background to those methods. It concentrates on the static design for stationary foundation conditions. Although the topic is far from exhaustively treated, it does intend to present most of the basic material needed for a practising engineer involved in routine geotechnical design, as well as provide the tools for an engineering student to approach and solve common geotechnical design problems.
Download or read book LRFD Bridge Design written by Tim Huff and published by CRC Press. This book was released on 2022-02-23 with total page 387 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book examines and explains material from the 9th edition of the AASHTO LRFD Bridge Design Specifications, including deck and parapet design, load calculations, limit states and load combinations, concrete and steel I-girder design, bearing design, and more. With increased focus on earthquake resiliency, two separate chapters– one on conventional seismic design and the other on seismic isolation applied to bridges– will fully address this vital topic. The primary focus is on steel and concrete I-girder bridges, with regard to both superstructure and substructure design. Features: Includes several worked examples for a project bridge as well as actual bridges designed by the author Examines seismic design concepts and design details for bridges Presents the latest material based on the 9th edition of the LRFD Bridge Design Specifications Covers fatigue, strength, service, and extreme event limit states Includes numerous solved problems and exercises at the end of each chapter to illustrate the concepts presented LRFD Bridge Design: Fundamentals and Applications will serve as a useful text for graduate and upper-level undergraduate civil engineering students as well as practicing structural engineers.
Download or read book AASHTO Guide Specifications for LRFD Seismic Bridge Design written by and published by AASHTO. This book was released on 2011 with total page 271 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work offers guidance on bridge design for extreme events induced by human beings. This document provides the designer with information on the response of concrete bridge columns subjected to blast loads as well as blast-resistant design and detailing guidelines and analytical models of blast load distribution. The content of this guideline should be considered in situations where resisting blast loads is deemed warranted by the owner or designer.
Download or read book Practice Problems for the Civil Engineering PE Exam written by Michael R. Lindeburg and published by Professional Publications Incorporated. This book was released on 2003 with total page 628 pages. Available in PDF, EPUB and Kindle. Book excerpt: More than 430 practice problems with solutions. Updated with new codes and standards tested on the exam.
Download or read book Gravel Roads written by Ken Skorseth and published by . This book was released on 2000 with total page 112 pages. Available in PDF, EPUB and Kindle. Book excerpt: The purpose of this manual is to provide clear and helpful information for maintaining gravel roads. Very little technical help is available to small agencies that are responsible for managing these roads. Gravel road maintenance has traditionally been "more of an art than a science" and very few formal standards exist. This manual contains guidelines to help answer the questions that arise concerning gravel road maintenance such as: What is enough surface crown? What is too much? What causes corrugation? The information is as nontechnical as possible without sacrificing clear guidelines and instructions on how to do the job right.
Download or read book Guide Specifications for Seismic Isolation Design written by and published by AASHTO. This book was released on 2010 with total page 63 pages. Available in PDF, EPUB and Kindle. Book excerpt: This edition is based on the work of NCHRP project 20-7, task 262 and updates the 2nd (1999) edition -- P. ix.
Download or read book Pile Design and Construction Rules of Thumb written by Ruwan Abey Rajapakse and published by Butterworth-Heinemann. This book was released on 2016-02-20 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: Pile Design and Construction Rules of Thumb presents Geotechnical and Civil Engineers a comprehensive coverage of Pile Foundation related theory and practice. Based on the author's experience as a PE, the book brings concise theory and extensive calculations, examples and case studies that can be easily applied by professional in their day-to-day challenges. In its first part, the book covers the fundamentals of Pile Selection: Soil investigation, condition, pile types and how to choose them. In the second part it addresses the Design of Pile Foundations, including different types of soils, pile groups, pile settlement and pile design in rock. Next, the most extensive part covers Design Strategies and contains chapters on loading analysis, load distribution, negative skin friction, design for expansive soils, wave equation analysis, batter piles, seismic analysis and the use of softwares for design aid. The fourth part covers Construction Methods including hammers, Inspection, cost estimation, load tests, offshore piling, beams and caps. In this new and updated edition the author has incorporated new pile designs such as helical, composite, wind turbine monopiles, and spiral coil energy piles. All calculations have been updated to most current materials characteristics and designs available in the market. Also, new chapters on negative skin friction, pile driving, and pile load testing have been added. Practicing Geotechnical, and Civil Engineers will find in this book an excellent handbook for frequent consult, benefiting from the clear and direct calculations, examples, and cases. Civil Engineering preparing for PE exams may benefit from the extensive coverage of the subject. - Convenient for day-to-day consults - Numerous design examples for sandy soils, clay soils, and seismic loadings - Now including helical, composite, wind turbine monopiles, and spiral coil energy piles - Methodologies and case studies for different pile types - Serves as PE exam preparation material
Download or read book Concrete Structures Subjected to Impact and Blast Loadings and Their Combinations written by Chunwei Zhang and published by CRC Press. This book was released on 2022-05-08 with total page 335 pages. Available in PDF, EPUB and Kindle. Book excerpt: Although much research focuses on investigating the responses of reinforced concrete (RC) structures under sole impact or blast loads, the responses of RC structures under a combination of impact and blast loads currently represent a gap in our knowledge. The combined actions of impact and blast loadings may be applied to RC structures during accidental or intentional collision of vessels, vehicles, etc., carrying explosive materials. A comprehensive study on the vulnerability of various structural members is carried out using finite element (FE) simulations under combination of impact and blast loads with the variations of various loading- and structural-related parameters and key parameters. This book introduces various structural analysis approaches for concrete structures when subjected to extreme loads such as impact and blast loadings. The theory of the combinations of impact and blast loads is proposed that can provide primary insights to the specific readers to develop new ideas in impact and blast engineering, including combined actions of extreme loads arising from real-world intentional or accidental events. This book will be of value to students (undergraduate or postgraduate), engineers, and researchers in structural and civil engineering, and specifically, those who are studying and investigating the performances of concrete structures under extreme loads.
Download or read book Design of Highway Bridges written by Richard M. Barker and published by John Wiley & Sons. This book was released on 2013-02-04 with total page 1194 pages. Available in PDF, EPUB and Kindle. Book excerpt: Up-to-date coverage of bridge design and analysis revised to reflect the fifth edition of the AASHTO LRFD specifications Design of Highway Bridges, Third Edition offers detailed coverage of engineering basics for the design of short- and medium-span bridges. Revised to conform with the latest fifth edition of the American Association of State Highway and Transportation Officials (AASHTO) LRFD Bridge Design Specifications, it is an excellent engineering resource for both professionals and students. This updated edition has been reorganized throughout, spreading the material into twenty shorter, more focused chapters that make information even easier to find and navigate. It also features: Expanded coverage of computer modeling, calibration of service limit states, rigid method system analysis, and concrete shear Information on key bridge types, selection principles, and aesthetic issues Dozens of worked problems that allow techniques to be applied to real-world problems and design specifications A new color insert of bridge photographs, including examples of historical and aesthetic significance New coverage of the "green" aspects of recycled steel Selected references for further study From gaining a quick familiarity with the AASHTO LRFD specifications to seeking broader guidance on highway bridge design Design of Highway Bridges is the one-stop, ready reference that puts information at your fingertips, while also serving as an excellent study guide and reference for the U.S. Professional Engineering Examination.
