Download or read book Contaminants Removal and Rare Earth Elements Recovery from Coal Mine Drainage by Using bio electro Chemical Methods written by Meisam Peiravi and published by . This book was released on 2018 with total page 276 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mining activities, as essential as they are for our economy and our society, bring pollutants such as acid mine drainage (AMD) which contains dissolved metal(loid)s into the environment. There are different technologies currently being practiced to treat AMD, but many of these methods are prohibitive in industry due to high energy, material and labor requirements. This study investigated two emerging technologies to treat AMD with high removal rates of some metals. In addition, as AMD contains strategic metals such as rare earth elements (REEs), hydrometallurgical and biosorptive approaches were used to recover REEs from AMD, hydrometallurgical recovery method was also applied for coal by-products for the method developed. A two-chamber bioelectrochemical system (BES) was used to remove different types of metals from AMD. After 7 days, the pH of the cathode solution increased from 2.5 to 7.3. More than 99% of Al, Fe and Pb were removed, and removal rates of 93%, 91%, 89% and 69% were achieved for Cd, Zn, Mn, and Co, respectively, at the biocathode. Energy-dispersive X-ray spectroscopy (EDS) studies revealed the deposition of the various metals on the cathode surface, and some metals were detected in precipitates from the cathode chamber. During the BES operation, ~30-50 mV of closed circuit voltage was obtained for different conditions. A single-chambered BES study was conducted for the removal of Cd, Ni, and Mn in mine drainage. Compared to a double chamber, a single chamber BES is easier to design and operate. The removal process was studied with activated sludge from a local wastewater treatment plant. The effect of applied voltage, time, and initial concertation of these metals on their removal rate was studied. For Cd initial concentrations of 625 and 165 μg/L, 1.0 V showed the highest removal efficiency, and ~93 and 95% of Cd were removed, respectively. For a Ni initial concentration of 2,440 μg/L, 72% was removed under 1.0 V compared to the control of 77%. However, for a lower initial Ni concentration of 190 μg/L, 1.0 V was better compared than other conditions, and it removed 92% of Ni. For a Mn initial concentration of 1,800 μg/L, 1.0 V had a better result, however, only ~19% of the Mn was removed. For a lower Mn initial concentration of 390 μg/L, 1.0 V was favorable only at 24 h and the removal rate was ~37%. Nanoscale zerovalent iron (nZVI) was used to remove contaminants from AMD. These contaminants include transition metals (Co, Ni, Cu, Mn, and Zn), alkali and alkaline earth metals (Li, Mg, and Ca), metalloid (As), nonmetals (Se and S), and active metal (Al). Purchased nZVI in concentrations of 10-6500 mg/L was used for a reaction duration of up to 480 min. The pH of the AMD increased linearly with increasing concentrations of nZVI, with a maximum of 6.0 ± 0.1 at 6500 mg/L of nZVI. Cu and Al had the highest removal rate among all other elements. With 10 mg/L of nZVI, ~100% of Cu was removed within 120 min. Up to ~98% of Al was removed with 5000 mg/L of nZVI in 480 min. Reuse of the purchased nZVI was studied for the first time for AMD treatment; after reuse in the second cycle, the nZVI was no longer effective. Lab-made nZVI by the precipitation method was tested for a longer time of 48 h. Removal rates for different elements did not change after ~8 h (e.g., 480 min), and in general, the lab-made nZVI had better removal efficiency compared to the purchased nZVI, with removal rate of ~28-79% when using 80 mg/L of the lab-made nZVI. Besides Cu, Al, Ni, and Co, successful removal of Mg and Ca, as well as S, Co, Li, As, and Se from AMD was reported for the first time by using nZVI. Different coal ranks were examined for REE concentration from coal ash. Maximum REE content of more than 700 mg/kg was observed for the highest-rank coal (anthracite) sample, and that was used for leaching and recovery studies. Hydrometallurgical processes including leaching, solvent extraction, stripping, and precipitation were performed to recover REEs from coal ash. Nitric acid leaching tests were conducted at 95 °C using a 4×2×2 factorial design. The results indicated that the highest rate of light REEs (LREEs) recovery was achieved at the highest molarity of the acid solution, lowest solids content and longest retention time. However, the highest rate of heavy REEs (HREEs) recovery needed only an intermediate level of acid molarity. The highest recovery rates of 90% for LREEs and 94% for HREEs were obtained. Recirculation of the leachate was conducted to prepare the REE-concentrated solution for the solvent extraction. (Abstract shortened by ProQuest.)

Download or read book Recovery of Byproducts from Acid Mine Drainage Treatment written by Elvis Fosso-Kankeu and published by John Wiley & Sons. This book was released on 2020-09-04 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt: Recent developments have provided the opportunity to recover valuable materials from AMD treatment; this is a sustainable approach that allows to reduce waste while generating incomes that balance the cost of the treatment. This book provides insights to innovative and affordable routes for AMD valorisation that can certainly motivate the mining industry to effectively manage their wastes and minimize environmental impact while generating jobs opportunities.

Download or read book Electrokinetic Remediation for Environmental Security and Sustainability written by Alexandra B. Ribeiro and published by John Wiley & Sons. This book was released on 2021-03-22 with total page 732 pages. Available in PDF, EPUB and Kindle. Book excerpt: Electrokinetic Remediation for Environmental Security and Sustainability Explore this comprehensive reference on the remediation of contaminated substrates, filled with cutting-edge research and practical case studies Electrokinetic Remediation for Environmental Security and Sustainability delivers a thorough review of electrokinetic remediation (EKR) for the treatment of inorganic and organic contaminants in contaminated substrates. The book highlights recent progress and developments in EKR in the areas of resource recovery, the removal of pollutants, and environmental remediation. It also discusses the use of EKR in conjunction with nanotechnology and phytoremediation. Throughout the book, case studies are presented that involve the field implementation of EKR technologies. The book also includes discussions of enhanced electrokinetic remediation of dredged co-contaminated sediments, solar-powered bioelectrokinetics for the mitigation of contaminated agricultural soil, advanced electro-fenton for remediation of organics, electrokinetic remediation for PPCPs in contaminated substrates, and the electrokinetic remediation of agrochemicals such as organochlorine compounds. Other topics include: A thorough introduction to the modelling of electrokinetic remediation An exploration of the electrokinetic recovery of tungsten and removal of arsenic from mining secondary resources An analysis of pharmaceutically active compounds in wastewater treatment plants with a discussion of electrochemical advanced oxidation as an on-site treatment A review of rare earth elements, including general concepts and recovery techniques, like electrodialytic extraction A treatment of hydrocarbon-contaminated soil in cold climate conditions Perfect for environmental engineers and scientists, geologists, chemical engineers, biochemical engineers, and scientists working with green technology, Electrokinetic Remediation for Environmental Security and Sustainability will also earn a place in the libraries of academic and industry researchers, engineers, regulators, and policy makers with an interest in the remediation of contaminated natural resources.

Download or read book Metal Recovery from Electronic Waste Biological Versus Chemical Leaching for Recovery of Copper and Gold written by Arda Işildar and published by CRC Press. This book was released on 2018-10-30 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: Waste electrical and electronic equipment (WEEE) generation is a global problem. Despite the growing awareness and deterring legislation, most of the WEEE is disposed improperly, i.e. landfilled or otherwise shipped overseas, and treated in sub-standard conditions. Informal recycling of WEEE has catastrophic effects on humans and the environment. WEEE contains considerable quantities of valuable metals such as base metals, precious metals and rare earth elements (REE). Metal recovery from WEEE is conventionally carried out by pyrometallurgical and hydrometallurgical methods. In this PhD research, novel metal recovery technologies from WEEE are investigated. Using acidophilic and cyanide-generating bacteria, copper and gold were removed from crushed electronic waste with removal efficiencies of 98.4 and 44.0%, respectively. The leached metals in solution were recovered using sulfidic precipitation and electrowinning separation techniques. Finally, a techno-economic assessment of the technology was studied. This research addresses the knowledge gap on two metal extraction approaches, namely chemical and biological, from a secondary source of metals. The essential parameters of the selective metal recovery processes, scale-up potential, techno-economic and sustainability assessment have been studied.

Download or read book Bioremediation Nutrients and Other Valuable Product Recovery written by Lakhveer Singh and published by Elsevier. This book was released on 2020-12-04 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: Bioremediation and Nutrients and Other Valuable Products Recovery: Using Bio-electrochemical Systems reviews key applications in transforming fuel waste substrates into simple low impact and easily assimilative compounds that are environmentally non-labile and tolerant. The book emphasizes waste treatment and nutrient removal and recovery from a diverse array of waste substrates, utilizing Bioelectrochemical Systems (BES) approaches. Throughout, the work emphasizes the utilization of electrode and/or electrolyte components in building self-sustaining fuel cell systems that target the removal of both conventional and emerging pollutants, along with the production of energy. Bioremediation strategies with potential scale-up options for wastewater treatment, metal removal and soil remediation drug derivates and emerging contaminants are discussed with particular emphasis. Chapters explore applications for these varied pollutants, together with prospects in waste minimization, nutrient recycling, water purification and bioremediation of natural resources. Explores a detailed panorama of potential known pollutants with detailed reviews on their removal and recovery Discusses bioproduct recovery application frontiers across wastewater treatment and bioremediation, metal removal and soil remediation, extraction of drug derivates and emerging contaminants Emphasizes pilot scale-up and commercialization potential for each recovery application discussed

Download or read book Mining E waste and Coal Ash in Landfills for Rare Earth Elements Using Bioleaching Methods written by Samiha Karim and published by . This book was released on 2022 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Bioleaching is an economical process to extract rare earth elements, which requires less energyand produces less toxic gases than chemical extraction methods. However, the extraction efficiency varies with different parameters. Bioleaching mechanisms, as well as factors controlling the process, were comprehensively analyzed in this study. The quantitative analysis will help optimize bioleaching process parameters for the high co-extraction of metals. Analyzing 61 peer-reviewed articles on bioleaching, we identified three main factors that affect the bioleaching mechanism - microorganism type, source type, and specific REE. Extraction efficiency varies between 0 to 100% based on the condition used in the study. Among different types of microorganisms used to extract REE, fungi were found to have a competitive advantage over other microorganisms such as chemolithoautotrophs or heterotrophs. Primary and secondary sources of REE are typically used for extraction. Among them, electronic waste leaches more REE per unit mass of source reacted, irrespective of the microorganism type. Extraction efficiencies of transition metals were higher than those of REEs

Download or read book Bio Geotechnologies for Mine Site Rehabilitation written by M.N.V. Prasad and published by Elsevier. This book was released on 2018-01-02 with total page 732 pages. Available in PDF, EPUB and Kindle. Book excerpt: Bio-Geotechnologies for Mine Site Rehabilitation deals with the biological, physical, chemical, and engineering approaches necessary for the reclamation of mine waste. As mining has negative effects on natural resources and deteriorates the quality of the surrounding environment, this book provides coverage across different types of mining industries, which are currently creating industrial deserts overloaded with technogenic waste. The book offers cost-effective strategies and approaches for contaminated sites, along with remediation and rehabilitation methods for contaminated soils and waste dumps. It is an essential resource for students and academics, but is also ideal for applied professionals in environmental geology, mineral geologists, biotechnologists and policymakers. Deals with global and holistic approaches of abandoned mine land rehabilitation Includes mine waste rehabilitation case studies from around the world Covers integrated technologies, such as bioremediation of metalliferous soil Provide strategies for sustainable ecosystems on mine spoil dumps Offers novel methods for the remediation of acid mine drainage

Download or read book Bioelectrochemistry Stimulated Environmental Remediation written by Ai-Jie Wang and published by Springer. This book was released on 2019-09-14 with total page 310 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews the latest advances in the bioelectrochemical degradation of recalcitrant environmental contaminants. The first part introduces readers to the basic principles and methodologies of bioelectrochemical systems, electron-respiring microorganisms, the electron transfer mechanism and functional electrode materials. In turn, the second part addresses the bioelectrochemical remediation/treatment of various environmental pollutants (including highly toxic refractory organics, heavy metals, and nitrates) in wastewater, sediment and wetlands. Reactor configuration optimization, hybrid technology amplification and enhanced removal principles and techniques are also discussed. The book offers a valuable resource for all researchers and professionals working in environmental science and engineering, bioelectrochemistry, environmental microbiology and biotechnology.

Download or read book Metal Removal and Recovery from Mining Wastewater and E waste Leachate written by Suthee Janyasuthiwong and published by CRC Press. This book was released on 2020-02-18 with total page 161 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal contamination in the environment is a persisting global issue. The metal reservoirs in the earth have declined due to society’s needs and due to uncontrolled mining activities. Therefore, the idea to recover metals from waste streams has emerged. In this thesis, cost competitive technologies such as adsorption using agro-wastes and precipitation using an inverse fluidized bed (IFB) reactor were investigated, with special emphasis on the recovery of base metals. Groundnut shell showed good potential for metal (Cu, Pb and Zn) removal. From artificial neural network modeling, the performance of the sulfate reducing bacteria (SRB) was found to be strongly pH dependent; the removal efficiency of Cu and Zn in the IFB at pH 5.0 was >97%. Electronic waste is a good candidate as secondary metal resource. The recovery of Cu from computer printed circuited boards (PCBs) using biogenic sulfide precipitation was investigated as well. Using this technology, Cu could be recovered at ~0.48 g Cu/g PCBs.

Download or read book Agromining Farming for Metals written by Antony van der Ent and published by Springer Nature. This book was released on 2020-12-07 with total page 482 pages. Available in PDF, EPUB and Kindle. Book excerpt: This second and expanded edition of the first book on agromining (phytomining) presents a comprehensive overview of the metal farming & recovery of the agromining production chain. Agromining is an emerging technology that aims to transform the extraction of sources of target elements not accessible by traditional mining and processing techniques. Agromining, which is based on sustainable development, uses hyperaccumulator plants as 'metal crops' farmed on sub-economic soils or minerals wastes to obtain valuable target elements. This volume is edited and authored by the pioneers in the rapidly expanding field of agromining and presents the latest insights and developments in the field. This book provides in-depth information on the global distribution and ecology of hyperaccumulator plants, their biogeochemical pathways, the influence of rhizosphere microbes, the physiology and molecular biology of hyperaccumulation, as well as aspects of propagation and conservation of these unusual plants. It describes the agronomy of metal crops and opportunities for incorporating agromining into rehabilitation and mine closure, including test cases for agromining of nickel, cobalt, manganese, arsenic, selenium, cadmium, zinc, thallium, rare earth elements and platinum group elements. Since the first edition was published, there have successful nickel agromining field trials in the tropics (in Malaysia and Guatemala), and these are presented in a dedicated case study chapter. Other new chapters focus on the processing of bio-ore for elements other than nickel, such as rare earth elements and cadmium, and on agromining from industrial wastes such as tailings, and industrial by-products and sites. Furthermore, the book features two new chapters that provide a comprehensive assessment of accumulation a very wide range elements from the Periodic Table in various plant species around the globe, and a chapter on practical methods for discovery of hyperaccumulator plant species in the field and in the herbarium. This book is of interest to environmental professionals in the minerals industry, government regulators, and academics.

Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1974 with total page 852 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Application of Nanotechnology in Mining Processes written by Elvis Fosso-Kankeu and published by John Wiley & Sons. This book was released on 2022-01-31 with total page 384 pages. Available in PDF, EPUB and Kindle. Book excerpt: b”Application of Nanotechnology in Mining ProcessesNanotechnology has revolutionized processes in many industries but its application in the mining industry has not been widely discussed. This unique book provides an overview of the successful implementation of nanotechnology in some of the key environmental and beneficiation mining processes. This book explores extensively the potential of nanotechnology to revolutionize the mining industry which has been relying for a very long on processes with limited efficiencies. The nine specialized chapters focus on applying nanoflotation to improve mineral processing, effective extraction of metals from leachates or pregnant solutions using nanoscale supramolecular hosts, and development of nano-adsorbents or nano-based strategies for the remediation or valorization of AMD. The application of nanotechnology in mining has so far received little attention from the industry and researchers and this groundbreaking book features critical issues so far under-reported in the literature: Application of nanotechnology in mineral processing for the enhancement of froth flotation Development of smart nanomaterials and application for the treatment of acid mine drainage Recovery of values from pregnant solutions using nanoadsorbents Valorization of AMD through formation of multipurpose nanoproducts. Audience Industrial interest will be from mining plant operators, environmental managers, water treatment plants managers, and operators. Researchers in nanotechnology, environmental science, mining, and metallurgy engineering will find the book valuable, as will government entities such as regulatory bodies officers and environmentalists.

Download or read book Enhanced Bioweathering of Coal for Rare Earth Element Extraction and Concentration written by Ankur Sachan and published by . This book was released on 2019 with total page 256 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rare earth elements (REEs) are a group of seventeen elements that include scandium, yttrium, and fifteen of the lanthanide series elements, which are used in a variety of consumer goods and for defense purposes. Acquiring a domestic profitable source of REEs is a critical national need as most of the global supply comes from one country, China. To counter this problem, the US is actively looking at alternative sources of REEs by implementing unconventional methods of extraction. Coal is one of the alternative sources of REEs. Alaskan coal from Wishbone Hill and Healy are known to contain REEs up to 286 ppm and 524 ppm, respectively, while having concentrations as high as 950 ppm on ash basis in some density fractions. Microbial leaching or bioleaching is a novel method that can be used for extraction of REEs from coal as microbes are known to affect earth’s surface over geologic time by playing critical roles in weathering of minerals. A certain species of bacteria, Shewanella oneidensis MR-1, was used to separate the REEs from Wishbone Hill and Healy coal samples. The experiments were performed for various density fractions of both coals by varying solids percentage, temperature, size of coal, and bacterial concentration, and recovery of REEs for these conditions was recorded. Highest individual recovery of neodymium, 75.3%, was obtained for Wishbone Hill 1.3 floats, while a maximum of 98.4% total REE recovery was obtained for Healy 1.3 sinks. Healy coal has the higher total recovery of REEs in comparison to Wishbone Hill coal. Bioleaching process was also compared to the acid leaching process. Healy coal responded better to bioleaching than the acid leaching process. The Wishbone Hill coal had comparable recoveries of bioleaching with acid leaching, although they were always less than acid leaching.

Download or read book Bioelectrochemical Oxidation Processes for Wastewater Treatment written by Maulin P. Shah and published by CRC Press. This book was released on 2024-09-30 with total page 292 pages. Available in PDF, EPUB and Kindle. Book excerpt: Toxic and hazardous pollutant treatment of wastewater is a longstanding challenge faced in every region across the globe. Growing urbanization, combined with the increased use of detergent soaps, cleansing agents with new formulations, chemical fertilizers, and pesticides, has greatly added to the global wastewater pollution burden. Conventional methods of wastewater treatment are somewhat successful in decontamination, but these current techniques require more time and energy than newer, novel techniques. Bioelectrochemical oxidation systems (BEOSs), for example, have greatly aided in wastewater treatment sustainability and efficiency, and offer promising solutions for different types of energy recovery options. Bioelectrochemical Oxidation Processes for Wastewater Treatment examines the latest hybrid technologies utilizing algae, bacteria, and various other chemical agents, and discusses the major challenges in large-scale operations, as well as forward-looking techniques to make treatment processes even more sustainable in the future. It: Discusses the fundamentals of biological wastewater treatment and bioelectrochemical oxidation systems, as well as their advantages and limitations. Presents the recent trends and developments in bioelectrochemical oxidation systems for achieving environmentally sustainable wastewater treatment. Describes carbon capture and resource recovery from wastewater using bioelectrochemical oxidation systems. Addresses the challenges of large-scale implementation of bioelectrochemical oxidation systems in existing and new wastewater treatment plants.

Download or read book Biohydrometallurgical Processes written by Satarupa Dey and published by CRC Press. This book was released on 2023-12-06 with total page 373 pages. Available in PDF, EPUB and Kindle. Book excerpt: Extensive industrialization has led to an increased release of toxic metals into the soil and air. Industrial waste can include mine overburden, bauxite residue, and E waste, and these can serve as a source of valuable recoverable metals. There are relatively simple methods to recycle these wastes, but they require additional chemicals, are expensive, and generate secondary waste that causes environmental pollution. Biohydrometallurgical processing is a cost-effective and ecofriendly alternative where biological processes help conserve dwindling ore resources and extract metals in a nonpolluting way. Microbes can be used in metal extraction from primary ores, waste minerals, and industrial and mining wastes. Biohydrometallurgical Processes: Metal Recovery and Remediation serves as a useful guide for microbiologists, biotechnologists, and various industrialists dealing with mining, metallurgy, chemical engineering, and environmental sciences. Features: Examines advances in biohydrometallurgy, biomineralization, and bioleaching techniques Discusses the importance of bacteria in biohydrometallurgical processes and microbial interventions for waste cleanup and upgradation of minerals Presents the latest techniques for biosynthesis related to different metals, along with recent developments in alternative procedures using extremophiles and leaching bacteria

Download or read book Electrochemical Remediation Technologies for Polluted Soils Sediments and Groundwater written by Krishna R. Reddy and published by John Wiley & Sons. This book was released on 2009-08-04 with total page 756 pages. Available in PDF, EPUB and Kindle. Book excerpt: An unmatched reference on electrochemical technologies for soil, sediment, and groundwater pollution remediation Electrochemical technologies are emerging as important approaches for effective and efficient pollution remediation, both on their own and in concert with other remediation techniques. Electrochemical Remediation Technologies for Polluted Soils, Sediments and Groundwater provides a systematic and clear explanation of fundamentals, field applications, as well as opportunities and challenges in developing and implementing electrochemical remediation technologies. Written by leading authorities in their various areas, the text summarizes the latest research and offers case studies that illustrate equipment, installation, and methods employed in real-world remediations. Divided into nine sections, the coverage includes: Introduction and fundamental principles Remediation of heavy metals and other inorganic pollutants Remediation of organic pollutants Remediation of mixed contaminants Electrokinetic barriers Integrated (coupled) technologies Mathematical modeling Economic and regulatory considerations Field applications and performance assessment Unique as a comprehensive reference on the subject, Electrochemical Remediation Technologies for Polluted Soils, Sediments and Groundwater will serve as a valuable resource to all environmental engineers, scientists, regulators, and policymakers.

Download or read book Emerging Contaminants in the Terrestrial Aquatic Atmosphere Continuum written by Willis Gwenzi and published by Elsevier. This book was released on 2022-05-06 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt: Emerging Contaminants in Terrestrial and Aquatic Environments: Occurrence, Health Risks, and Mitigation provides the latest information on the synthesis of the occurrence, behavior, human health risks and mitigation of emerging contaminants in developing countries. First highlighting sources, industrial applications, key drivers and regulatory frameworks, the book then goes on to discuss the nature of emerging contaminants, including organic (e.g., pharmaceuticals), inorganic (e.g., rare earth elements) and biological agents (e.g., antimicrobial resistance). It then presents the dissemination, environmental behavior, and fate in terrestrial and aquatic systems as well as the human and ecological exposure pathways, health risks, and more. Offering a transdisciplinary approach that brings together perspectives and contributions from experts in environmental sciences, hydrology, environmental engineering, ecotoxicology, chemistry, material sciences, and legal and policy aspects, the book provides an approachable and flexible resource for researchers and upper-level students with diverse academic backgrounds. Adopts a lifecycle perspective by including industrial applications, behavior and fate and human health risks and removal Focuses on developing regions and covers a wide range of emerging contaminants, including those often overlooked in earlier books such as rare earth elements and antimicrobial resistance Presents a clear understanding of the contrasts between developed and developing countries with respect to emerging contaminants and their health risks and mitigation, including water and wastewater treatment systems commonly used in developing countries Covers human and ecological health risks in developing countries