Download or read book Conducted EMC Modeling and EMI Filter Design Integrated Class D Amplifiers and Power Converters written by Roberto Mrad and published by . This book was released on 2014 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt: Switching power management circuits are widely used in battery powered embedded applications in order to increase their autonomy. In particular, for audio applications, Class-D amplifiers are a widespread industrial solution. These, have a similar architecture of a buck converter but having the audio signal as reference. The switching nature of these devices allows us to increase significantly the power efficiency compared to linear audio amplifiers without reducing the audio quality. However, because of the switching behavior, Class-D amplifiers have high levels of electromagnetic (EM) emissions which can disturb the surrounding electronics or might not comply with electromagnetic compatibility (EMC) standards. To overcome this problem much architecture appeared in the state of the art that reduces the emissions, however, this has never been enough to remove electromagnetic interference (EMI) filters. It is then useful to optimize these filters, thus, it has been set as the goal of this PhD thesis. The latter has been divided to four main axes which can be resumed by the following. First, this work started by developing a frequency domain modeling method in order to simulate and predict the EMI of Class-D amplifiers in the final application. The method is based on system to block decomposition and impedance matrix modeling and manipulation. After providing all the theoretical background, the method has been validated on integrated differential Class-D amplifier. The experimental measurements have permitted to validate the method only up to 100MHz. However, this is sufficient to cover the conducted EMC frequency band. Second, the EMI at the supply rails of Class-D amplifiers has been treated. As the battery is often the same power supply for all applications in an embedded system, an EMI filter or a decoupling capacitor is needed to prevent the noise coupling by common impedance. Designing this filter needs the knowledge of the battery impedance at the desired frequencies. Therefore the present work dealt also with measuring the high frequency impedance of a battery. Afterwards, an experimental validation has been carried on with a DC-DC converter and a Class-D amplifier. The developed model allows a virtual test of the switching device in the final application. However, it is more useful if the model is able to help the system integrator in designing filters. Thus, third, the model has been implemented in an optimization loop based on a genetic algorithm in order to optimize the filter response, and also, reduce the additional power losses introduced by an EMI filter. The optimization search space has been limited to the components available on the market and the optimization result is given as component references of the optimal filter referring to the optimal solution found. This procedure has been validated experimentally. Finally, EMI filters often are constituted by magnetic components such as ferrite beads or inductors with magnetic cores. Thus, introducing the EMI filter in the audio path, adds a nonlinear behavior in the audio frequency band. Designing a high quality EMI filter require taking into account this phenomenon and studying its impact of the original amplifier audio performance. Therefore, the Jiles-Atherton model for magnetic materials has been used for ferrite bead modeling. Hereafter, the impact on the time and frequency domain signals has been simulated and compared to measurements. Finally, the total harmonic distortion (THD) has been computed for different signal amplitudes and compared to the THD measured using an audio analyzer. Accurate results have been obtained on a wide range of signal amplitudes. As a conclusion, this work aimed to design optimal EMI filters for Class-D amplifiers. Thus, we dealt with improving their EMI response, reducing their additional power losses and evaluating their impact on the audio quality.

Download or read book Advancements in Automation and Control Technologies written by Sarojini Selvaperumal and published by Trans Tech Publications Ltd. This book was released on 2014-06-18 with total page 872 pages. Available in PDF, EPUB and Kindle. Book excerpt: Selected, peer reviewed papers from the 2014 International Conference on Advancements in Automation and Control (ICAAC 2014), April 11-12, 2014, Ramanathapuram, Tamilnadu, India

Download or read book Electromagnetic Bandgap EBG Structures written by Antonio Orlandi and published by John Wiley & Sons. This book was released on 2017-05-31 with total page 237 pages. Available in PDF, EPUB and Kindle. Book excerpt: An essential guide to the background, design, and application of common-mode filtering structures in modern high-speed differential communication links Written by a team of experts in the field, Electromagnetic Bandgap (EBG) Structures explores the practical electromagnetic bandgap based common mode filters for power integrity applications and covers the theoretical and practical design approaches for common mode filtering in high-speed printed circuit boards, especially for boards in high data-rate systems. The authors describe the classic applications of electromagnetic bandgap (EBG) structures and the phenomena of common mode generation in high speed digital boards. The text also explores the fundamental electromagnetic mechanisms of the functioning of planar EBGs and considers the impact of planar EBGs on the digital signal propagation of single ended and differential interconnects routed on top or between EBGs. The authors examine the concept, design, and modeling of EBG common mode filters in their two forms: on-board and removable. They also provide several comparisons between measurement and electromagnetic simulations that validate the proposed EBG filters' design approach. This important resource: • Presents information on planar EBG based common mode filters for high speed differential digital systems • Provides systematic analysis of the fundamental mechanisms of planar EBG structures • Offers detailed design methodology to create EBG filters without the need for repeated full-wave electromagnetic analysis • Demonstrates techniques for use in practical real-world designs Electromagnetic Bandgap (EBG) Structures: Common Mode Filters for High Speed Digital Systems offers an introduction to the background, design, and application of common-mode filtering structures in modern high-speed differential communication links, a critical issue in high-speed and high-performance systems.

Download or read book Power Line Filter Design for Switched mode Power Supplies written by Mark J. Nave and published by . This book was released on 2010 with total page 183 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Index to IEEE Publications written by Institute of Electrical and Electronics Engineers and published by . This book was released on 1996 with total page 1260 pages. Available in PDF, EPUB and Kindle. Book excerpt: Issues for 1973- cover the entire IEEE technical literature.

Download or read book EMI Filter Design written by Richard Lee Ozenbaugh and published by CRC Press. This book was released on 2000-11-09 with total page 348 pages. Available in PDF, EPUB and Kindle. Book excerpt: Offering simple methods of measuring AC and DC power lines, this highly popular, revised and expanded reference describes the selection of cores, capacitors, mechanical shapes, and styles for the timeliest design, construction, and testing of filters. It presents analyses of matrices of various filter types based on close approximations, observation, and trial and error. Supplying simple parameters and techniques for creating manufacturable, repeatable products, the second edition provides insights into the cause and elimination of common mode noise in lines and equipment, explores new data on spike, pulse, trapezoid, and quasisquare waves, and reviews the latest high-current filters.

Download or read book Distributed Power Amplifiers for RF and Microwave Communications written by Narendra Kumar and published by Artech House. This book was released on 2015-06-01 with total page 365 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new resource presents readers with all relevant information and comprehensive design methodology of wideband amplifiers. This book specifically focuses on distributed amplifiers and their main components, and presents numerous RF and microwave applications including well-known historical and recent architectures, theoretical approaches, circuit simulation, and practical implementation techniques. A great resource for practicing designers and engineers, this book contains numerous well-known and novel practical circuits, architectures, and theoretical approaches with detailed description of their operational principles.

Download or read book The Physical Basis of EMC written by Keith Armstrong and published by . This book was released on 2010 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book PCB Design for Real World EMI Control written by Bruce R. Archambeault and published by Springer Science & Business Media. This book was released on 2013-06-29 with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proper design of printed circuit boards can make the difference between a product passing emissions requirements during the first cycle or not. Traditional EMC design practices have been simply rule-based, that is, a list of rules-of-thumb are presented to the board designers to implement. When a particular rule-of-thumb is difficult to implement, it is often ignored. After the product is built, it will often fail emission requirements and various time consuming and costly add-ons are then required. Proper EMC design does not require advanced degrees from universities, nor does it require strenuous mathematics. It does require a basic understanding of the underlying principles of the potential causes of EMC emissions. With this basic understanding, circuit board designers can make trade-off decisions during the design phase to ensure optimum EMC design. Consideration of these potential sources will allow the design to pass the emissions requirements the first time in the test laboratory. A number of other books have been published on EMC. Most are general books on EMC and do not focus on printed circuit board is intended to help EMC engineers and design design. This book engineers understand the potential sources of emissions and how to reduce, control, or eliminate these sources. This book is intended to be a 'hands-on' book, that is, designers should be able to apply the concepts in this book directly to their designs in the real-world.

Download or read book Noise Reduction Techniques in Electronic Systems written by Henry W. Ott and published by Wiley-Interscience. This book was released on 1988-03-23 with total page 456 pages. Available in PDF, EPUB and Kindle. Book excerpt: This updated and expanded version of the very successful first edition offers new chapters on controlling the emission from electronic systems, especially digital systems, and on low-cost techniques for providing electromagnetic compatibility (EMC) for consumer products sold in a competitive market. There is also a new chapter on the susceptibility of electronic systems to electrostatic discharge. There is more material on FCC regulations, digital circuit noise and layout, and digital circuit radiation. Virtually all the material in the first edition has been retained. Contains a new appendix on FCC EMC test procedures.

Download or read book Automotive Electromagnetic Compatibility EMC written by Terence Rybak and published by Springer Science & Business Media. This book was released on 2007-06-14 with total page 302 pages. Available in PDF, EPUB and Kindle. Book excerpt: Anyone who has operated, serviced, or designed an automobile or truck in the last few years has most certainly noticed that the age of electronics in our vehicles is here! Electronic components and systems are used for everything from the traditional entertainment system to the latest in “drive by wire”, to two-way communication and navigation. The interesting fact is that the automotive industry has been based upon mechanical and materials engineering for much of its history without many of the techniques of electrical and electronic engineering. The emissions controls requirements of the 1970’s are generally recognized as the time when electronics started to make their way into the previous mechanically based systems and functions. While this revolution was going on, the electronics industry developed issues and concepts that were addressed to allow interoperation of the systems in the presence of each other and with the external environment. This included the study of electromagnetic compatibility, as systems and components started to have influence upon each other just due to their operation. EMC developed over the years, and has become a specialized area of engineering applicable to any area of systems that included electronics. Many well-understood aspects of EMC have been developed, just as many aspects of automotive systems have been developed. We are now at a point where the issues of EMC are becoming more and more integrated into the automotive industry.

Download or read book Applications of Power Electronics written by Frede Blaabjerg and published by MDPI. This book was released on 2019-06-24 with total page 476 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power electronics technology is still an emerging technology, and it has found its way into many applications, from renewable energy generation (i.e., wind power and solar power) to electrical vehicles (EVs), biomedical devices, and small appliances, such as laptop chargers. In the near future, electrical energy will be provided and handled by power electronics and consumed through power electronics; this not only will intensify the role of power electronics technology in power conversion processes, but also implies that power systems are undergoing a paradigm shift, from centralized distribution to distributed generation. Today, more than 1000 GW of renewable energy generation sources (photovoltaic (PV) and wind) have been installed, all of which are handled by power electronics technology. The main aim of this book is to highlight and address recent breakthroughs in the range of emerging applications in power electronics and in harmonic and electromagnetic interference (EMI) issues at device and system levels as discussed in ‎robust and reliable power electronics technologies, including fault prognosis and diagnosis technique stability of grid-connected converters and ‎smart control of power electronics in devices, microgrids, and at system levels.

Download or read book Power Supply Cookbook written by Marty Brown and published by Elsevier. This book was released on 2001-06-13 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: Power Supply Cookbook, Second Edition provides an easy-to-follow, step-by-step design framework for a wide variety of power supplies. With this book, anyone with a basic knowledge of electronics can create a very complicated power supply design in less than one day. With the common industry design approaches presented in each section, this unique book allows the reader to design linear, switching, and quasi-resonant switching power supplies in an organized fashion. Formerly complicated design topics such as magnetics, feedback loop compensation design, and EMI/RFI control are all described in simple language and design steps. This book also details easy-to-modify design examples that provide the reader with a design template useful for creating a variety of power supplies. This newly revised edition is a practical, "start-to-finish" design reference. It is organized to allow both seasoned and inexperienced engineers to quickly find and apply the information they need. Features of the new edition include updated information on the design of the output stages, selecting the controller IC, and other functions associated with power supplies, such as: switching power supply control, synchronization of the power supply to an external source, input low voltage inhibitors, loss of power signals, output voltage shut-down, major current loops, and paralleling filter capacitors. It also offers coverage of waveshaping techniques, major loss reduction techniques, snubbers, and quasi-resonant converters. - Guides engineers through a step-by-step design framework for a wide variety of power supplies, many of which can be designed in less than one day - Provides easy-to-understand information about often complicated topics, making power supply design a much more accessible and enjoyable process

Download or read book Switching Power Supplies A Z written by Sanjaya Maniktala and published by Elsevier. This book was released on 2012-04-04 with total page 769 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chapter 1: The Principles of Switching Power Conversion Chapter 2: DC-DC Converter Design and Magnetics Chapter 3: Off-line Converter Design and Magnetics Chapter 4: The Topology FAQ Chapter 5: Optimal Core Selection Chapter 6: Component Ratings, Stresses, Reliability and Life Chapter 7: Optimal Power Components Selection Chapter 8: Conduction and Switching Losses Chapter 9: Discovering New Topologies Chapter 10: Printed Circuit Board Layout Chapter 11: Thermal Management Chapter 12: Feedback Loop Analysis and Stability Chapter 13: Paralleling, Interleaving and Sharing Chapter 14: The Front-End of AC-DC Power Supplies Chapter 15: DM and CM Noise in Switching Power Supplies Chapter 16: Fixing EMI across the Board Chapter 17: Input Capacitor and Stability Chapter 18: The Math behind the Electromagnetic Puzzle Chapter 19: Solved Examples Appendix A.

Download or read book Electromagnetic Compatibility written by David A. Weston and published by CRC Press. This book was released on 2016-11-03 with total page 1311 pages. Available in PDF, EPUB and Kindle. Book excerpt: Revised, updated, and expanded, Electromagnetic Compatibility: Methods, Analysis, Circuits, and Measurement, Third Edition provides comprehensive practical coverage of the design, problem solving, and testing of electromagnetic compatibility (EMC) in electrical and electronic equipment and systems. This new edition provides novel information on theory, applications, evaluations, electromagnetic computational programs, and prediction techniques available. With sixty-nine schematics providing examples for circuit level electromagnetic interference (EMI) hardening and cost effective EMI problem solving, this book also includes 1130 illustrations and tables. Including extensive data on components and their correct implementation, the myths, misapplication, misconceptions, and fallacies that are common when discussing EMC/EMI will also be addressed and corrected.

Download or read book Science Abstracts written by and published by . This book was released on 1995 with total page 1990 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book High Frequency Magnetic Components written by Marian K. Kazimierczuk and published by John Wiley & Sons. This book was released on 2011-08-24 with total page 510 pages. Available in PDF, EPUB and Kindle. Book excerpt: If you are looking for a complete study of the fundamental concepts in magnetic theory, read this book. No other textbook covers magnetic components of inductors and transformers for high-frequency applications in detail. This unique text examines design techniques of the major types of inductors and transformers used for a wide variety of high-frequency applications including switching-mode power supplies (SMPS) and resonant circuits. It describes skin effect and proximity effect in detail to provide you with a sound understanding of high-frequency phenomena. As well as this, you will discover thorough coverage on: integrated inductors and the self-capacitance of inductors and transformers, with expressions for self-capacitances in magnetic components; criteria for selecting the core material, as well as core shape and size, and an evaluation of soft ferromagnetic materials used for magnetic cores; winding resistance at high frequencies; expressions for winding and core power losses when non-sinusoidal inductor or transformer current waveforms contain harmonics. Case studies, practical design examples and procedures (using the area product method and the geometry coefficient method) are expertly combined with concept-orientated explanations and student-friendly analysis. Supplied at the end of each chapter are summaries of the key concepts, review questions, and problems, the answers to which are available in a separate solutions manual. Such features make this a fantastic textbook for graduates, senior level undergraduates and professors in the area of power electronics in addition to electrical and computer engineering. This is also an inimitable reference guide for design engineers of power electronics circuits, high-frequency transformers and inductors in areas such as (SMPS) and RF power amplifiers and circuits.