Download or read book Computational Modelling of the Mechanical Behavior of Nanocrystalline Metals Based on the Deformation Mechanisms and Their Transitions written by Baozhi Zhu and published by . This book was released on 2006 with total page 152 pages. Available in PDF, EPUB and Kindle. Book excerpt: There has been a growing research interest in understanding the mechanical behaviors and the deformation mechanisms of nanocrystalline metals and alloys in the past a few decades, due to their extraordinary mechanical prosperities, such as high strength, hardness, and wear resistance, which have great potentials in engineering applications. As grain sizes in crystalline metals and alloys transit down to the lower end of the nanometer range, the plastic deformations are no longer dominated by the intragrain dislocation activities. Instead deformations assisted by grain boundary start to play a more important role in deciding the mechanical response of the bulk materials, as the interfacial volume fraction increases with the reduction of grain sizes. A polycrystalline constitutive theory is developed in the form of the extend aggregate Taylor model of Asaro and Needleman for the nanocrystalline metals. The plastic deformation description is based on the Asaro, Krysl and Kad (AKK) model, which considers deformation mechanisms such as the emission of perfect, partial dislocations and deformation twins from grain boundary and grain boundary sliding when the grain size is sufficiently small in the nanometer regime (less than 100nm), and their transitions are governed by the factors such as grain size, stacking fault energy, temperature, and strain rate, etc. Therefore the effect of grain size distributions in addition to the mean grain size is considered important on the mechanical response in this constitutive theory. The grain size distributions can be simulated with the experimentally determined lognormal distributions for the electro-deposited nanocrystalline metals for example. Numerical simulations are carried out for nanocrystalline Ni, Cu, Al and Pd, and the simulated phenomena include the mechanical response of these materials when subjected to uniaxial tension and compression under different deformation rates, texture development under high pressure torsion (HPT), and the grain growth effect during nanoindentation, etc, where the contribution of each deformation mechanism is carefully studied. The obtained numerical results are in reasonably good agreement with the experiments. Due to the fact that the deformation mechanisms in nanostructured materials are not yet fully understood, this constitutive theory will need to be further improved with the future findings of deformation mechanisms, which this theory has the flexibility to easily incorporate.
Download or read book Atomistic and Continuum Modeling of Nanocrystalline Materials written by Laurent Capolungo and published by Springer Science & Business Media. This book was released on 2010-03-17 with total page 409 pages. Available in PDF, EPUB and Kindle. Book excerpt: Atomistic and Continuum Modeling of Nanocrystalline Materials develops a complete and rigorous state-of-the-art analysis of the modeling of the mechanical behavior of nanocrystalline (NC) materials. Among other key topics, the material focuses on the novel techniques used to predict the behavior of nanocrystalline materials. Particular attention is given to recent theoretical and computational frameworks combining atomistic and continuum approaches. Also, the most relevant deformation mechanisms governing the response of nanocrystalline materials are addressed and discussed in correlation with available experimental data.
Download or read book Analytical and Computational Modeling of the Mechanical Response of Polycrystalline and Nanocrystalline Metals written by Hsueh-Hung Fu and published by . This book was released on 2003 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Microstructural Heterogeneity and the Mechanical Behavior of Nanocrystalline Metals written by Jagannathan Rajagopalan and published by . This book was released on 2009 with total page 190 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ultrafine grained and nanocrystalline metals have attracted increasing interest, both scientific and commercial, in recent years because of their potentially superior mechanical properties. Their properties, such as very high strength, primarily arise from the change in the underlying deformation mechanisms. Experimental and simulation studies have shown that because of the extremely small grain size conventional dislocation plasticity is curtailed in these materials and grain boundary mediated mechanisms become more important. Although the deformation behavior and the underlying mechanisms in these materials have been investigated in depth, relatively little attention has been focused on the inhomogeneous nature of their microstructure and its influence on their macroscopic response.
Download or read book Plastic Deformation in Nanocrystalline Materials written by Mikhail Gutkin and published by Springer Science & Business Media. This book was released on 2013-04-18 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt: It seems there is no special need to comment on the term 'nanostructure' now, when one often meets the 'nano' words not only in scientific journals but even in newspapers. Moreover, today they are even to be heard in TV and radio programmes. In academic science, where the terms 'nanostructure' and 'nan otechnology' have been extremely popular since the early 1990s, they have been successfully extended to the sphere of economics and business, and now to politics. This is quite natural because nanostructures and nanotechnolo gies will surely serve as a basis for the most advanced and highest technology production in the nearest and probably also the remote future. Hence, the struggle to create and occupy its markets is already under way. In this respect, it is of great interest to review data on the dynamics of U. S. Federal Goverment expenditure for nanotechnology [1,2]. In the fiscal years 1997 and 2002, expenditure was approximately US$116 and US$ 697 million, respectively. In the fiscal year 2004, the President's request for US federal in vestment in nanoscale science, engineering and technology is about US$ 849 million [2]. The indicative budget allocated to the Thematic Priority enti tled 'Nanotechnologies and nanosciences, knowledge-based multifunctional materials and new production processes and devices' for the duration 2002- 2006 of the sixth EU Framework Programme for Research and Technological Development is EUR 1300 million [3].
Download or read book Continuum Models of Deformation Mechanisms in Nanocrystalline Metals written by Antoine Jérusalem and published by . This book was released on 2007 with total page 129 pages. Available in PDF, EPUB and Kindle. Book excerpt: (Cont.) Part of the legacy of this thesis work is a computational framework for large-scale simulation of the continuum-level response of nanocrystalline metals. This parallel computing framework was developed in order to address the necessity of describing the full three-dimensional response of large number of grains subject to a wide range of loading conditions.
Download or read book Cold Rolling Texture of Electrodeposited Nanocrystalline FCC Metals written by Yanling Yang and published by American Academic Press. This book was released on 2018-01-16 with total page 131 pages. Available in PDF, EPUB and Kindle. Book excerpt: Properties of nanocrystalline metals or alloys cannot be predicted according to the phenomena observed in traditional coarse-grained materials. Nanocrystalline materials exhibit special physical and chemical properties, such as extremely high mechanical strength, outstanding thermal, optical, magnetic and electrical properties. Deformation mechanisms of nanocrystalline materials have been discussed for many years. Previous literatures mainly focus on the investigation of deformation behaviors through in-situ experimental methods such as in-situ TEM observation or simulation methods by modeling. With regard to the in-situ TEM observation, it still remains controversial whether the TEM results can represent the deformation behaviors of bulk nanocrystalline materials. In line with the molecular dynamics simulation method, the materials are frequently assumed to be ideal and the strain rate utilized is extraordinarily high. All the above conditions almost cannot be met or validated through experiments. In this work, it is attempted to explore deformation mechanisms of nanocrystalline face-centered cubic metals or alloys based on texture evolution during plastic deformation. Dislocation movements in plastic deformation process are always followed by formation of deformation texture in most cases, and plastic deformation coordinated by grain boundary sliding and/or grain rotation mechanisms does not incur the occurrence of crystallographic texture. Therefore, investigations on texture evolution during plastic deformation are able to provide powerful evidence for the deformation mechanisms of nanocrystalline materials.
Download or read book Dissertation Abstracts International written by and published by . This book was released on 2007 with total page 854 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Defects and Deformation in Nanostructured Metals written by Christopher Earl Carlton and published by . This book was released on 2009 with total page 394 pages. Available in PDF, EPUB and Kindle. Book excerpt: A better understanding of how the nanoscale environment affects the mechanical properties of materials, in particular metallic nanoparticles and nanocrystalline metals is vital to the development of next generation materials. Of special interest is obtaining a fundamental understanding of the inverse Hall-Petch Effect in nanocrystalline metals, and nanoindentation in individual nanoparticles. Understanding these subjects is critical to understanding how the mechanical properties of materials are fundamentally affected by nanoscale dimensions. These topics have been addressed by a combination of theoretical modeling and in-situ nanoindentation transmission electron microscopy (TEM) analysis. Specifically, the study of the inverse Hall-Petch effect in nanocrystalline metals will be investigated by a thorough review of the literature followed by a proposed novel theoretical model that better explains the experimentally observed behavior of nanocrystalline metals. On the other hand, the nanoindentation of individual nanoparticles is a very new research topic that has yet to aggregate a large body of experimental data. In this context, in-situ TEM nanoindentation experiments on silver nanoparticles will be first performed to determine the mechanisms of deformation in these nanostructures. A theoretical explanation for the observed deformation mechanisms will be then developed and its implications will be discussed. In addition to nanoparticles, this study will also provide unique and valuable insight into the deformation mechanisms of nanopillars, a growing area of research despite much controversy and speculation about their actual mechanisms of deformation. After studying the novel behavior of both nanocrystalline metals and nanoparticles, useful applications of both classes of materials will be explored. The discussion of applications will focus on utilizing the interesting behaviors explored in the dissertation. Of particular interest will be applications of nanoparticles and nanocrystalline materials to coatings, radiation resistance and super-plastic materials.
Download or read book Investigating the Mechanical Behavior and Deformation Mechanisms of Ultrafine grained Metal Films Using Ex situ and In situ TEM Techniques written by Ehsan Izadi and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanocrystalline (NC) and Ultrafine-grained (UFG) metal films exhibit a wide range of enhanced mechanical properties compared to their coarse-grained counterparts. These properties, such as very high strength, primarily arise from the change in the underlying deformation mechanisms. Experimental and simulation studies have shown that because of the small grain size, conventional dislocation plasticity is curtailed in these materials and grain boundary mediated mechanisms become more important. Although the deformation behavior and the underlying mechanisms in these materials have been investigated in depth, relatively little attention has been focused on the inhomogeneous nature of their microstructure (particularly originating from the texture of the film) and its influence on their macroscopic response. Furthermore, the rate dependency of mechanical response in NC/UFG metal films with different textures has not been systematically investigated. The objectives of this dissertation are two-fold. The first objective is to carry out a systematic investigation of the mechanical behavior of NC/UFG thin films with different textures under different loading rates. This includes a novel approach to study the effect of texture-induced plastic anisotropy on mechanical behavior of the films. Efforts are made to correlate the behavior of UFG metal films and the underlying deformation mechanisms. The second objective is to understand the deformation mechanisms of UFG aluminum films using in-situ transmission electron microscopy (TEM) experiments with Automated Crystal Orientation Mapping. This technique enables us to investigate grain rotations in UFG Al films and to monitor the microstructural changes in these films during deformation, thereby revealing detailed information about the deformation mechanisms prevalent in UFG metal films.
Download or read book Nanostructure Stabilization and Mechanical Behavior of Binary Nanocrystalline Alloys written by Jason R. Trelewicz and published by . This book was released on 2008 with total page 290 pages. Available in PDF, EPUB and Kindle. Book excerpt: The unique mechanical behavior of nanocrystalline metals has become of great interest in recent years, owing to both their remarkable strength and the emergence of new deformation physics at the nanoscale. Of particular interest has been the breakdown in Hall-Petch strength scaling, which is frequently attributed by atomistic simulations to a mechanistic shift to interface dominated plasticity. Experimental validation has been less abundant, primarily due to the processing challenges associated with achieving homogeneous nanocrystalline samples suitable for mechanical testing. Alloying has been proposed as a potential route to high-quality nanocrystalline metals, although choice of an appropriate alloy system, based on available thermodynamic data, remains elusive. In this thesis, we propose a thermodynamic model for nanostructure stabilization that derives from the energetic state variables characteristic of binary alloys. These modeling results motivate the study of Ni-W alloys in particular, which may be synthesized via aqueous electrodeposition, accessing grain sizes across the entire Hall-Petch breakdown regime as characterized by x-ray diffraction and transmission electron microscopy. Ambient temperature nanoindentation testing is employed to evaluate the mechanical behavior of the as-deposited alloys, assessing the nature of flow, the rate sensitivity, and pressure sensitivity of deformation, with emphasis on property inflections required to bridge the behavior of nanocrystalline metals to amorphous solids. The rate sensitivity, in particular, demonstrates an inherent dependence on nanocrystalline grain size, exhibiting a maximum in the vicinity of the Hall-Petch breakdown as a consequence of a shift to glass-like shear localization. In light of this finding, we study the Hall-Petch breakdown at high strain rates, and show that an "inverse Hall-Petch" weakening regime emerges at high rates. Additional effects from structural relaxation are investigated, and illustrated to strongly influence the strength scaling behavior and shift to inhomogeneous flow. Relaxed samples are also subjected to elevated temperature indentation tests, and the results discussed in the context of thermally-activated plasticity, thus providing a more quantitative analysis of the nanoscale deformation mechanisms.
Download or read book Advances in Nanotechnology Research and Application 2011 Edition written by and published by ScholarlyEditions. This book was released on 2012-01-09 with total page 8760 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advances in Nanotechnology Research and Application: 2011 Edition is a ScholarlyEditions™ eBook that delivers timely, authoritative, and comprehensive information about Nanotechnology. The editors have built Advances in Nanotechnology Research and Application: 2011 Edition on the vast information databases of ScholarlyNews.™ You can expect the information about Nanotechnology in this eBook to be deeper than what you can access anywhere else, as well as consistently reliable, authoritative, informed, and relevant. The content of Advances in Nanotechnology Research and Application: 2011 Edition has been produced by the world’s leading scientists, engineers, analysts, research institutions, and companies. All of the content is from peer-reviewed sources, and all of it is written, assembled, and edited by the editors at ScholarlyEditions™ and available exclusively from us. You now have a source you can cite with authority, confidence, and credibility. More information is available at http://www.ScholarlyEditions.com/.
Download or read book Atomistic Simulations of Defect Nucleation and Free Volume in Nanocrystalline Materials written by Garritt J. Tucker and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Atomistic simulations are employed in this thesis to investigate defect nucleation and free volume of grain boundaries and nanocrystalline materials. Nanocrystalline materials are of particular interest due to their improved mechanical properties and alternative strain accommodation processes at the nanoscale. These processes, or deformation mechanisms, within nanocrystalline materials are strongly dictated by the larger volume fraction of grain boundaries and interfaces due to smaller average grain sizes. The behavior of grain boundaries within nanocrystalline materials is still largely unknown. One reason is that experimental investigation at this scale is often difficult, time consuming, expensive, or impossible with current resources. Atomistic simulations have shown the potential to probe fundamental behavior at these length scales and provide vital insight into material mechanisms. Therefore, work conducted in this thesis will utilize atomistic simulations to explore structure-property relationships of face-centered-cubic grain boundaries, and investigate the deformation of nanocrystalline copper as a function of average grain size. Volume-averaged kinematic metrics are formulated from continuum mechanics theory to estimate nonlocal deformation fields and probe the nanoscale features unique to strain accommodation mechanisms in nanocrystalline metals. The kinematic metrics are also leveraged to explore the tensile deformation of nanocrystalline copper at 10K. The distribution of different deformation mechanisms is calculated and we are able to partition the role of competing mechanisms in the overall strain of the nanocrystalline structure as a function of grain size. Grain boundaries are observed to be influential in smaller grained structures, while dislocation glide is more influential as grain size increases. Under compression, however, the resolved compressive normal stress on interfaces hinders grain boundary plasticity, leading to a tension-compression asymmetry in the strength of nanocrystalline copper. The mechanisms responsible for the asymmetry are probed with atomistic simulations and the volume-averaged metrics. Finally, the utility of the metrics in capturing nonlocal nanoscale deformation behavior and their potential to inform higher-scaled models is discussed.
Download or read book Nanostructured Metals and Alloys written by S H Whang and published by Elsevier. This book was released on 2011-03-22 with total page 840 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile strength, fatigue strength and ductility are important properties of nanostructured metallic materials, which make them suitable for use in applications where strength or strength-to-weight ratios are important. Nanostructured metals and alloys reviews the latest technologies used for production of these materials, as well as recent advances in research into their structure and mechanical properties.One of the most important issues facing nanostructured metals and alloys is how to produce them. Part one describes the different methods used to process bulk nanostructured metals and alloys, including chapters on severe plastic deformation, mechanical alloying and electrodeposition among others. Part two concentrates on the microstructure and properties of nanostructured metals, with chapters studying deformation structures such as twins, microstructure of ferrous alloys by equal channel angular processing, and characteristic structures of nanostructured metals prepared by plastic deformation. In part three, the mechanical properties of nanostructured metals and alloys are discussed, with chapters on such topics as strengthening mechanisms, nanostructured metals based on molecular dynamics computer simulations, and surface deformation. Part four focuses on existing and developing applications of nanostructured metals and alloys, covering topics such as nanostructured steel for automotives, steel sheet and nanostructured coatings by spraying.With its distinguished editor and international team of contributors, Nanostructured metals and alloys is a standard reference for manufacturers of metal components, as well as those with an academic research interest in metals and materials with enhanced properties.
Download or read book Mechanical Properties and Deformation Behavior of Materials Having Ultra Fine Microstructures written by Michael Anthony Nastasi and published by Springer Science & Business Media. This book was released on 1993 with total page 646 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the emerging class of new materials characterized by ultra-fine microstrucures. The NATO ASI which produced this book was the first international scientific meeting devoted to a discussion of the mechanical properties and deformation behavior of materials having grain sizes down to a few nanometers. Topics covered include superplasticity, tribology, and the supermodulus effect. Review chapters cover a variety of other themes including synthesis, characterization, thermodynamic stability, and general physical properties. Much of the work is concerned with the issue of how far conventional techniques and concepts can be extended toward atomic scale probing. Another key issue concerns the structure of nanocrystalline materials, in particular, what is the structure and composition of the internal boundaries. These ultra-fine microstructures have proved to challenge even the finest probes that the materials science community has today.
Download or read book Nanocrystalline Alloys written by Timothy John Rupert and published by . This book was released on 2011 with total page 132 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanocrystalline materials have experienced a great deal of attention in recent years, largely due to their impressive array of physical properties. In particular, nanocrystalline mechanical behavior has been of interest, as incredible strengths are predicted when grain size is reduced to the nanometer range. The vast majority of research to this point has focused on quantifying and understanding the grain size-dependence of strength, leading to the discovery of novel, grain boundary-dominated physics that begin to control deformation at extremely fine grain sizes. With the emergence of this detailed understanding of nanocrystalline deformation mechanisms, the opportunity now exists for studies that explore how other structural features affect mechanical properties in order to identify alternative strengthening mechanisms. In this thesis, we seek to extend our current knowledge of nanocrystalline structure-property relationships beyond just grain size, using combinations of structural characterization, mechanical testing, and atomistic simulations. Controlled experiments on Ni-W are first used to show that solid solution addition and the relaxation of nonequilibrium grain boundary state can dramatically affect the strength of nanocrystalline metals. Next, the sliding wear response of nanocrystalline Ni-W is investigated, to show how alloying and grain boundary structural state affect a more complex mechanical property. This type of mechanical loading also provides a strong driving force for structural evolution, which, in this case, is found to be beneficial. Mechanically-driven grain growth and grain boundary relaxation occur near the surface of the Ni-W samples during sliding, leading to a hardening effect that improves wear resistance and results in a deviation from Archard scaling. Finally, molecular dynamics simulations are performed to confirm that mechanical cycling alone can indeed relax grain boundary structure and strengthen nanocrystalline materials. In all of the cases discuss above, our observations can be directly connected to the unique deformation physics of nanocrystalline materials.
Download or read book Mechanical Properties of Nanocrystalline Materials written by James C. M. Li and published by CRC Press. This book was released on 2011-09-02 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book concentrates on both understanding and development of nanocrystalline materials. The original relation that connects grain size and strength, known as the Hall-Petch relation, is studied in the nanometer grain size region. The breakdown of such a relation is a challenge. Why and how to overcome it? Is the dislocation mechanism still operating when the grain size is very small, approaching the amorphous limit? How do we go from the microstructure information to the continuum description of the mechanical properties?
