Download or read book Characterization of Multi wall Carbon Nanotubes and Their Applications written by Anestis Katsounaros and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes (CNT) and their applications is a field which has attract a lot of interest in the past two decades. Since the first invention of CNTs in 1991, and in view of utilising nanoantennas, the focus in many laboratories around the world has shifted to trying to lengthen nanotubes longer from nanometers to few centimeters. Eventually this could lead to CNTs' use in sub-millimeter, millimiter wave and microwave antenna applications. In this thesis, fundamental properties of carbon nanotube films are investigated, and some applications such as the use of CNTs as absorbers or CNT doped liquid crystals are considered. The concept of frequency tunable patch antennas is also presented. Simulation and measurement results of the liquid crystal based antenna show that frequency tuning is possible, through the use of a liquid crystal cell as a substrate. Additionally, greater tuning can be achieved using liquid crystals with higher dielectric anisotropy at microwave frequencies. This can be achieved by using CNT doped liquid crystals. As mentioned, microwave and terahertz measurements of vertically aligned carbon nanotube arrays placed on the top surface of a rectangular silicon substrate are presented. The S-parameters are calculated allowing the extraction of the complex permittivity, permeability and conductivity of the samples. Theoretical models are being introduced delineating the behaviour of the multi-walled nanotube (MWNT) samples. The material properties of this film provide useful data for potential microwave and terahertz applications such as absorbers. Finally, finite-difference time-domain (FDTD) modelling of CNTs is introduced, verifying the measurements that have been performed, confirming that CNT arrays can be highly absorptive. A novel estimation of the permittivity and permeability of an individual carbon nanotube is presented and a periodic structure is simulated, under periodic boundary conditions, consisting of solid anisotropic cylinders. In addition, the optical properties of vertically aligned carbon nanotube (V ACNT) arrays, when the periodicity is both within the sub-wavelength and wavelength regime are calculated. The effect of geometrical parameters of the tube such as length, diameter and inter-tube distance between two consecutive tubes are also examined.
Download or read book Carbon Nanotubes and Related Structures written by Dirk M. Guldi and published by John Wiley & Sons. This book was released on 2010-01-26 with total page 562 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by the most prominent experts and pioneers in the field, this ready reference combines fundamental research, recent breakthroughs and real-life applications in one well-organized treatise. As such, both newcomers and established researchers will find here a wide range of current methods for producing and characterizing carbon nanotubes using imaging as well as spectroscopic techniques. One major part of this thorough overview is devoted to the controlled chemical functionalization of carbon nanotubes, covering intriguing applications in photovoltaics, organic electronics and materials design. The latest research on novel carbon-derived structures, such as graphene, nanoonions and carbon pea pods, round off the book.
Download or read book Carbon Nanotube Polymer Composites written by Dimitrios Tasis and published by Royal Society of Chemistry. This book was released on 2015-11-09 with total page 293 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chemically-modified carbon nanotubes (CNTs) exhibit a wide range of physical and chemical properties which makes them an attractive starting material for the preparation of super-strong and highly-conductive fibres and films. Much information is available across the primary literature, making it difficult to obtain an overall picture of the state-of-the-art. This volume brings together some of the leading researchers in the field from across the globe to present the potential these materials have, not only in developing and characterising novel materials but also the devices which can be fabricated from them. Topics featured in the book include Raman characterisation, industrial polymer materials, actuators and sensors and polymer reinforcement, with chapters prepared by highly-cited authors from across the globe. A valuable handbook for any academic or industrial laboratory, this book will appeal to newcomers to the field and established researchers alike.
Download or read book Characterization and Applications of Multiwalled Carbon Nanotubes written by Jenny Marie Hilding and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Carbon Nanotubes written by Michael J. O’Connell and published by CRC Press. This book was released on 2018-10-03 with total page 339 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since their discovery more than a decade ago, carbon nanotubes (CNTs) have held scientists and engineers in captive fascination, seated on the verge of enormous breakthroughs in areas such as medicine, electronics, and materials science, to name but a few. Taking a broad look at CNTs and the tools used to study them, Carbon Nanotubes: Properties and Applications comprises the efforts of leading nanotube researchers led by Michael O’Connell, protégé of the late father of nanotechnology, Richard Smalley. Each chapter is a self-contained treatise on various aspects of CNT synthesis, characterization, modification, and applications. The book opens with a general introduction to the basic characteristics and the history of CNTs, followed by discussions on synthesis methods and the growth of “peapod” structures. Coverage then moves to electronic properties and band structures of single-wall nanotubes (SWNTs), magnetic properties, Raman spectroscopy of electronic and chemical behavior, and electromechanical properties and applications in NEMS (nanoelectromechanical systems). Turning to applications, the final sections of the book explore mechanical properties of SWNTs spun into fibers, sidewall functionalization in composites, and using SWNTs as tips for scanning probe microscopes. Taking a fresh look at this burgeoning field, Carbon Nanotubes: Properties and Applications points the way toward making CNTs commercially viable.
Download or read book Handbook of Carbon Nanotubes written by Jiji Abraham and published by Springer Nature. This book was released on 2022-11-16 with total page 2099 pages. Available in PDF, EPUB and Kindle. Book excerpt: This Handbook covers the fundamentals of carbon nanotubes (CNT), their composites with different polymeric materials (both natural and synthetic) and their potential advanced applications. Three different parts dedicated to each of these aspects are provided, with chapters written by worldwide experts in the field. It provides in-depth information about this material serving as a reference book for a broad range of scientists, industrial practitioners, graduate and undergraduate students, and other professionals in the fields of polymer science and engineering, materials science, surface science, bioengineering and chemical engineering. Part 1 comprises 22 chapters covering early stages of the development of CNT, synthesis techniques, growth mechanism, the physics and chemistry of CNT, various innovative characterization techniques, the need of functionalization and different types of functionalization methods as well as the different properties of CNT. A full chapter is devoted to theory and simulation aspects. Moreover, it pursues a significant amount of work on life cycle analysis of CNT and toxicity aspects. Part 2 covers CNT-based polymer nanocomposites in approximately 23 chapters. It starts with a short introduction about polymer nanocomposites with special emphasis on CNT-based polymer nanocomposites, different manufacturing techniques as well as critical issues concerning CNT-based polymer nanocomposites. The text deeply reviews various classes of polymers like thermoset, elastomer, latex, amorphous thermoplastic, crystalline thermoplastic and polymer fibers used to prepare CNT based polymer composites. It provides detailed awareness about the characterization of polymer composites. The morphological, rheological, mechanical, viscoelastic, thermal, electrical, electromagnetic shielding properties are discussed in detail. A chapter dedicated to the simulation and multiscale modelling of polymer nanocomposites is an additional attraction of this part of the Handbook. Part 3 covers various potential applications of CNT in approximately 27 chapters. It focuses on individual applications of CNT including mechanical applications, energy conversion and storage applications, fuel cells and water splitting, solar cells and photovoltaics, sensing applications, nanofluidics, nanoelectronics and microelectronic devices, nano-optics, nanophotonics and nano-optoelectronics, non-linear optical applications, piezo electric applications, agriculture applications, biomedical applications, thermal materials, environmental remediation applications, anti-microbial and antibacterial properties and other miscellaneous applications and multi-functional applications of CNT based polymer nanocomposites. One chapter is fully focussed on carbon nanotube research developments: published papers and patents. Risks associated with carbon nanotubes and competitive analysis of carbon nanotubes with other carbon allotropes are also addressed in this Handbook.
Download or read book Carbon Nanotubes for Biomedical Applications written by Rüdiger Klingeler and published by Springer Science & Business Media. This book was released on 2011-02-09 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book explores the potential of multi-functional carbon nanotubes for biomedical applications. It combines contributions from chemistry, physics, biology, engineering, and medicine. The complete overview of the state-of-the-art addresses different synthesis and biofunctionalisation routes and shows the structural and magnetic properties of nanotubes relevant to biomedical applications. Particular emphasis is put on the interaction of carbon nanotubes with biological environments, i.e. toxicity, biocompatibility, cellular uptake, intracellular distribution, interaction with the immune system and environmental impact. The insertion of NMR-active substances allows diagnostic usage as markers and sensors, e.g. for imaging and contactless local temperature sensing. The potential of nanotubes for therapeutic applications is highlighted by studies on chemotherapeutic drug filling and release, targeting and magnetic hyperthermia studies for anti-cancer treatment at the cellular level.
Download or read book Organized Networks of Carbon Nanotubes written by K.R.V. Subramanian and published by CRC Press. This book was released on 2020-03-17 with total page 151 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this book, meshes and networks formed out of multiwalled carbon nanotubes are investigated and analyzed, including their use in niche applications such as electro-optic devices, advanced mechanical, thermal and electrical property enhancement, and gene editing. Different properties of multi-walled carbon nanotubes, including random network formation, ordering the meshes and networks by mechanical agitation and application of an external field, using crystallization and cross-linking induced phase separation in homopolymers-CNT composites are discussed with theoretical analysis. The book is aimed at researchers and graduate students in Electrical Engineering; Materials Science and Engineering; Chemical Engineering and Nanotechnology, Electronic circuit design, manufacturing, and characterization.
Download or read book Functionalization and Characterization of Multiwalled Carbon Nanotubes for Nanorobotic Applications written by Kaiyu Shou and published by . This book was released on 2011 with total page 131 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Carbon Nanotubes Synthesis Characterization and Applications written by Kamal K. Kar and published by Research Publishing Service. This book was released on 2011 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Carbon Nanotubes and Graphene written by Kazuyoshi Tanaka and published by Newnes. This book was released on 2014-07-10 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon Nanotubes and Graphene is a timely second edition of the original Science and Technology of Carbon Nanotubes. Updated to include expanded coverage of the preparation, purification, structural characterization, and common application areas of single- and multi-walled CNT structures, this work compares, contrasts, and, where appropriate, unitizes CNT to graphene. This much expanded second edition reference supports knowledge discovery, production of impactful carbon research, encourages transition between research fields, and aids the formation of emergent applications. New chapters encompass recent developments in the theoretical treatments of electronic and vibrational structures, and magnetic, optical, and electrical solid-state properties, providing a vital base to research. Current and potential applications of both materials, including the prospect for large-scale synthesis of graphene, biological structures, and flexible electronics, are also critically discussed. - Updated discussion of properties, structure, and morphology of biological and flexible electronic applications aids fundamental knowledge discovery - Innovative parallel focus on nanotubes and graphene enables you to learn from the successes and failures of, respectively, mature and emergent partner research disciplines - High-quality figures and tables on physical and mathematical applications expertly summarize key information – essential if you need quick, critically relevant data
Download or read book Multi Walled Carbon Nanotubes written by Simone Morais and published by MDPI. This book was released on 2019-07-15 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt: Since their discovery, multi-walled carbon nanotubes (MWCNTs) have received tremendous attention due to their unique electrical, optical, physical, chemical, and mechanical properties. Remarkable advances have been made in the synthesis, purification, structural characterization, functionalization, and application of MWCNTs. Their particular characteristics make them well suited for a plethora of applications in a number of fields, namely nanoelectronics, nanofluids, energy management, (electro)catalysis, materials science, construction of (bio)sensors based on different detection schemes, multifunctional nanoprobes for biomedical imaging, and sorbents for sample preparation or removal of contaminants from wastewater. They are also useful as anti-bacterial agents, drug delivery nanocarriers, etc. The current relevant application areas are countless. This Special Issue presents original research and review articles that address advances, trends, challenges, and future perspectives regarding synthetic routes, structural features, properties, behaviors, and industrial or scientific applications of MWCNTs in established and emerging areas.
Download or read book Perspective of Carbon Nanotubes written by Hosam El-Din Saleh and published by BoD – Books on Demand. This book was released on 2019-12-11 with total page 250 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes belong to new nanomaterials and have been known for almost 20 years, but their history is somewhat lengthier. They have been identified as promising candidates for various applications.High-temperature preparation techniques are conventional techniques for the synthesis of carbon nanotubes using arc discharge or laser ablation, but today these methods are being replaced by low-temperature vapor deposition techniques, since orientation, alignment, nanotube length, diameter, purity, and density of carbon nanotubes can be precisely controlled. The synthesis of carbon nanotubes by chemical vapor deposition on catalyst arrays leads to nanotube models grown from specific sites on surfaces. The controlled synthesis of nanotubes opens up interesting possibilities in nanoscience and nanotechnologies, including electrical, mechanical and electromechanical properties and devices, chemical functionalization, surface chemistry and photochemistry, molecular sensors, and interfacing with moderate biological systems.Carbon nanotubes are used in many applications due to their unique electrical, mechanical, optical, thermal, and other properties. Conductive and high-strength composite materials, energy saving and energy conversion devices, sensors, visualization of field emissions and sources of radiation, means for storing hydrogen, and nanoscale semiconductor devices, probes, and interconnections are some of the many applications of carbon nanotubes.
Download or read book Nanotube Superfiber Materials written by Rachit Malik and published by Elsevier Inc. Chapters. This book was released on 2013-09-16 with total page 62 pages. Available in PDF, EPUB and Kindle. Book excerpt: Individual carbon nanotubes (CNTs) have exceptional mechanical and electrical properties. However, the transfer of these extraordinary qualities into CNT products, without compromising performance, remains a challenge. This chapter presents an overview of the manufacturing of CNT sheets and buckypaper and also describes research performed at the University of Cincinnati in this field. CNT arrays were grown using the chemical vapor deposition method. Sheets were drawn from the spinnable CNT arrays and characterized using scanning electron microscopy to show the highly unidirectional alignment of the nanotubes in the sheet. The anisotropic morphology of the sheet provides superior properties along one material axis as observed by measuring the tensile strength, electrical resistivity, optical transmittance, and electromagnetic interference shielding properties of the material. Surface modification of aligned multiwall nanotube sheets was carried out via incorporation of an atmospheric pressure plasma jet in the sheet posttreatment process. Helium/oxygen plasma was utilized to produce carboxyl (–COO−) functionality on the surface of the nanotubes. X-ray photoelectron spectroscopy confirmed the presence of the functional groups on the nanotube surface. The sheet was further characterized using Raman spectroscopy, Fourier transform infrared spectroscopy, and contact angle testing. Composite laminates made from functionalized CNT sheets showed higher strength than those made with pristine sheets. The effects of plasma power and oxygen concentration were studied in order to determine the best possible parameters for functionalization. Plasma treatment is a useful tool for fast, clean and dry functionalization of CNTs. This study demonstrates the ease of incorporating the plasma tool in the manufacturing process of sheets leading to the production of CNT/polymer composites. Macroscopic structures of nanotubes such as threads and sheets are leading to novel applications.
Download or read book Carbon Nanotubes written by Ann Rose Abraham and published by CRC Press. This book was released on 2022-10-06 with total page 341 pages. Available in PDF, EPUB and Kindle. Book excerpt: This new book discusses a selection of advanced topics on carbon nanotubes—their extraordinary properties, structure, design, fabrication, development, engineering, functionalization, carbon nanotube enabled nanocomposites, characterization, and, moreover, their utility in many applications. The volume highlights the amazing potential of advanced CNT composites in automotive, aeronautics, spacecrafts, transistors replacing Si electronics, energy, purification, hydrogen storage, tissue regeneration, electrochemical supercapacitors, sensing, biomedical applications, agriculture, energy, and technical applications. The book specifically discusses the applications of carbon nanotubes for a greener environment, as well as applications for biomedical uses, in drug delivery, and in display technology. It also explores the uses of CNTs in the energy and aerospace industries, such as for solar energy conversion, as a lubricant additive for enhancing energy efficiency, and more. Other chapters explore the potential of carbon nanotubes in hydrogen storage and carbon nanotube electronics.
Download or read book Carbon Nanomaterials for Agri Food and Environmental Applications written by Kamel Ahmed Abd-Elsalam and published by Micro & Nano Technologies. This book was released on 2019-11 with total page 652 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon Nanomaterials for Agri-food and Environmental Applications discusses the characterization, processing and applications of carbon-based nanostructured materials in the agricultural and environmental sectors. Sections discuss the synthesis and characterization of carbon nanotubes, the technological developments in environmental applications of carbon-based nanomaterials, and agri-food applications. The book also covers the toxic effects of engineered carbon nanoparticles on the environment, and in plants and animals. Finally, quality control and risk management are addressed to assess health and environmental risks. This is an applicable book for graduate students, researchers and those in industrial sectors of science and technology who want to learn more about carbon nanomaterials. Compares a range of carbon-based nanomaterials, showing how they are used for a range of agricultural and environmental applications Discusses the challenges and toxicity of different types of carbon-based nanomaterials for environmental and agricultural applications Explores when different classes of nanomaterial should be used in different environments
Download or read book Carbon Nanotubes written by Siva Yellampalli and published by BoD – Books on Demand. This book was released on 2011-07-20 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: Carbon nanotubes are one of the most intriguing new materials with extraordinary properties being discovered in the last decade. The unique structure of carbon nanotubes provides nanotubes with extraordinary mechanical and electrical properties. The outstanding properties that these materials possess have opened new interesting researches areas in nanoscience and nanotechnology. Although nanotubes are very promising in a wide variety of fields, application of individual nanotubes for large scale production has been limited. The main roadblocks, which hinder its use, are limited understanding of its synthesis and electrical properties which lead to difficulty in structure control, existence of impurities, and poor processability. This book makes an attempt to provide indepth study and analysis of various synthesis methods, processing techniques and characterization of carbon nanotubes that will lead to the increased applications of carbon nanotubes.
