Download or read book Automotive exhaust catalysis without noble metals written by Sander Stegenga and published by . This book was released on 1991 with total page 184 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Automobile Catalytic Converters written by Kathleen C. Taylor and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 61 pages. Available in PDF, EPUB and Kindle. Book excerpt: The use of catalytic converters for the purification of automotive exhaust gases is a relatively new technology which was brought into existence by social pressures for the preservation of acceptable environmental conditions. The majority of catalytic practitioners have been able to watch the growth of this technology from its inception to its current state of sophistication. Automotive catalytic converter technology is now in a mature state, and this chapter from Vol. 5 Catalysis: Science and Technology by Dr. K. C. Taylor provides a review which covers both the process chemistry and the most important converter design factors. Contents 1. Introduction. . . . . . . . . . . . . . 2. Emission Regulations in the United States. 3. Exhaust Emission Characteristics. . 3 4. 1981 Emission Control Technology. 5 A. Converters. . . 5 B. Control System. 7 8 ~. Catalyst Screening . 6. Laboratory Testing. .10 7. The Chemical Reactions 13 8. Composition of Three-Way Catalysts. 16 A. Rhodium 17 21 B. Platinum. C. Palladium 22 D. Iridium . 22 23 E. Ruthenium and Nickel. F. Cerium Oxide ..... 23 G. Search for Alternatives to Nohle Metals 24 9. Catalyst Supports . 25 A. Pellets .... 26 B. Monoliths . . 26 10. The Transient Behavior of Three-Way Catalysts 27 II. Deterioration of Three-Way Catalysts. 35 A. Thermal Effects. . . . 35 B. Phosphorus Poisoning. . . 37 C. Lead Poisoning. . . . . . · 38 D. Catalyst Poisoning by Sulfur · 40 12. The 0.4 NO,; Research Objective. · 41 13. Control of Diesel Particulate Emissions.
Download or read book Initial Oxidation Activity of Noble Metal Automotive Exhaust Catalysts written by Gerald J. Barnes and published by . This book was released on 1973 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Catalysis and Automotive Pollution Control II written by A. Crucq and published by Elsevier. This book was released on 1991-11-20 with total page 701 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume constitutes the proceedings of the second symposium on Catalysis and Automotive Pollution Control. CAPoC 2 was a great success from the point of view of its scientific interest, as evidenced by the content of this book, and also from the high participation, some 260 scientists. About two-thirds of the contributors came from the industrial world, mainly the car and oil industries and catalyst manufacturers. This is ample proof that exhaust catalysis remains a major topic of interest. The first part of the book is a general introduction to the problem of automotive pollution. The second, strictly catalytic, part is devoted to fundamental and applied studies on pollution control, with emphasis on exhaust catalytic converters.
Download or read book Catalysis written by John R. Anderson and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 289 pages. Available in PDF, EPUB and Kindle. Book excerpt: Catalytic steam reforming has grown during the last two or three decades into one of the world's great catalytic processes. It is of major economic significance since the products from it form the feed for a number of other major processes. Nevertheless, catalytic steam reforming is a relatively difficult technology. It operates at high temperatures where problems of the maintenance of materials integrity and of catalyst stability and activity are severe, the establishment of high thermal efficiency of the plant is economically vital, and reactor operation is strongly influenced by mass and heat transport effects. The process is the subject of a thorough review by Dr. J. R. Rostrup-Nielsen who discusses both the basic cataly tic chemistry and the way in which this is interrelated with reactor and plant design. The use of catalytic converters for the purification of automotive exhaust gases is a relatively new technology which was brought into existence by social pressures for the preservation of acceptable environmental conditions. The majority of catalytic practitioners have been able to watch the growth of this technology from its inception to its current state of sophistication. Automotive catalytic converter technology is now in a mature state, and the chapter in this volume by Dr. K. C. Taylor provides a review which covers both the process chemistry and the most important converter design factors.
Download or read book Catalysis and Automotive Pollution Control III written by A. Frennet and published by Elsevier. This book was released on 1995-11-02 with total page 959 pages. Available in PDF, EPUB and Kindle. Book excerpt: These proceedings are based on the third of a series of symposia devoted to the use of catalysis for the depollution of exhaust gases of motor vehicles. Although catalysts have been used for this purpose for some thirty years, the subject is still very topical because of its economic impact. The increasing number of submitted, accepted and published papers amply attests to this fact.
Download or read book Catalysis without Precious Metals written by R. Morris Bullock and published by John Wiley & Sons. This book was released on 2011-08-02 with total page 296 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written for chemists in industry and academia, this ready reference and handbook summarizes recent progress in the development of new catalysts that do not require precious metals. The research thus presented points the way to how new catalysts may ultimately supplant the use of precious metals in some types of reactions, while highlighting the remaining challenges. An essential copanion for organic and catalytic chemists, as well as those working with/on organometallics and graduate students. From the contents: * Catalysis Involving the H' Transfer Reactions of First-Row Transition Metals * Catalytic Reduction of Dinitrogen to Ammonia by Molybdenum Complexes * Molybdenum and Tungsten Catalysts for Hydrogenation, Hydrosilylation and Hydrolysis * Iron in Catalytic Alkene and Carbonyl Hydrogenation Reactions * Olefin Oligomerizations and Polymerizations Catalyzed by Iron and Cobalt Complexes * Cobalt and Nickel Catalyzed Reactions Involving C-H and C-N Activation Reactions * Development of Molecular Electrocatalysts for H2 Oxidation and Production Based on Inexpensive Metals * Nickel-Catalyzed Reductinve Couplings and Cyclizations * Copper-Catalyzed Ligand Promoted Ullmann-Type Coupling Reactions * Copper-Catalyzed Azide-Alkyne Cycloaddition * "Frustrated Lewis Pairs": A Metal-Free Strategy for Hydrogenation Catalysis
Download or read book Catalysis and Automotive Pollution Control written by A. Crucq and published by Elsevier. This book was released on 1987-04-01 with total page 521 pages. Available in PDF, EPUB and Kindle. Book excerpt: In June 1984 the EEC Commission proposed new standards of permissible exhaust gas from motor vehicles to be introduced in Europe; these standards were approved by the Ministers of the Environment one year later. As the control of automotive pollution is at present mainly a catalytic problem, it was decided to hold an International Symposium on the subject, and an organizing committee composed of people engaged in catalytic research in the different Belgian Universities was constituted. This was the first Symposium of its kind to be held on an international level, and the quality and scientific interest of the papers presented was exceptional. It is planned to hold a follow-up Symposium in 2 to 3 years' time.The first part of the book is a general introduction to the problem of automotive pollution. The second, properly catalytic, part is devoted to fundamental and applied studies on pollution control, with emphasis on exhaust catalytic converters.
Download or read book Catalysis and Automotive Pollution Control IV written by N. Kruse and published by Elsevier. This book was released on 1998-05-29 with total page 719 pages. Available in PDF, EPUB and Kindle. Book excerpt: In spite of the energy crises and the recession, there has been a global, explosive growth in the amount of motor vehicles. In the past 50 years, the amount has increased from 50 to 700 million vehicles. For economical reasons they will probably continue to be used for a considerable number of years, despite the poor yield of internal combustion engines resulting in the inevitable production of some gaseous pollutants. The subsequent increase of gaseous pollutants in our atmosphere caused by exhaust gas from automobiles has enhanced the problem of the elimination of these pollutants produced by internal combustion engines. Catalysis has proven to be the best solution to lower the content of exhaust gas in pollutants.As its predecessors, CAPoC4 proved to be a suitable platform for discussing technological improvements and developments along with future perspectives and challenges. In the light of new results and further legislative regulations, the following topics were intensely discussed: *low light-off behaviour based on improved catalysts and substrate formulations *efficient adsorber systems for storage of hydrocarbon emissions *electrically heated catalyst systems ahead the main catalyst or, alternatively, close coupled catalysts (at the manifold of the engine) • lean DeNOx catalysts allowing for decomposition of NOx in the oxygen-rich exhaust of direct injection gasoline engines and high speed injection diesel engines or, alternatively, NOx trapping/reduction in a hybrid approach * collection and destruction of dry particulates or soot.There is no doubt that clean vehicle technology is a vital part of improving air quality. Challenges remain and call for technological answers. Catalytic air pollution control is still an area providing a considerable incentive for innovative work.
Download or read book Automotive Pollution Control Catalysts and Devices written by Marshall Sittig and published by William Andrew. This book was released on 1977 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Noble Metals written by Yen-Hsun Su and published by BoD – Books on Demand. This book was released on 2012-02-01 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides a broad spectrum of insights into the optical principle, resource, fabrication, nanoscience, and nanotechnology of noble metal. It also looks at the advanced implementation of noble metal in the field of nanoscale materials, catalysts and biosystem. This book is ideal not only for scientific researchers but also as a reference for professionals in material science, engineering, nonascience and plasmonics.
Download or read book New Frontiers in Catalysis Parts A C written by L. Guczi and published by Elsevier. This book was released on 1993-04-20 with total page 2955 pages. Available in PDF, EPUB and Kindle. Book excerpt: These volumes comprise the proceedings of the major international meeting on catalysis which is held at 4 year intervals. The programme focussed on New Frontiers in Catalysis including nontraditional catalytic materials and environmental catalysis. The contributions cover a wide range of fundamental, applied, industrial and engineering aspects of catalysis. The extensive range of highly efficient industrial techniques for observing and characterizing catalytically important surfaces is evident.The programme covered the following sessions: Mechanism, theory, in situ methods; Catalytic reaction on atomically clean surfaces; Catalytic reaction on zeolites and related substances; New methods and principles for catalyst preparation; Hydrotreatment reactions (HDS, HDN); Characterization of catalysts, application of novel techniques; Selective oxidation; New catalytic aspects of heteropoly acids and related compounds; Reaction of hydrocarbons; Nontraditional catalytic materials; Fuel upgrading; Alkane activation; Acid-base catalysis; New selective catalytic reactons, fine chemicals; Environmental catalysis; Industrial catalysis, deactivation, reactivation; Synthesis from syngas; Electrocatalysis; Photocatalysis.The invited lectures and 433 papers included in these volumes present an update on all areas of catalysis and applications.
Download or read book Supported Metals in Catalysis written by James Arthur Anderson and published by World Scientific. This book was released on 2012 with total page 581 pages. Available in PDF, EPUB and Kindle. Book excerpt: With contributions from experts in supported metal catalysis, from both the industry and academia, this book presents the latest developments in characterization and application of supported metals in heterogeneous catalysis. In addition to a thorough and updated coverage of the traditional aspects of heterogeneous catalysis such as preparation, characterization and use in well-established technologies such as Naphtha reforming, the book also includes emerging areas where supported metal catalysis will make significant contributions in future developments, such as fuel cells and fine chemicals synthesis. The second edition of Supported Metals in Catalysis comes complete with new and updated chapters containing important summaries of research in a rapidly evolving field. Very few other books deal with this highly pertinent subject matter, and as such, it is a must-have for anyone working in the field of heterogeneous catalysis.
Download or read book Advanced Materials in Catalysis written by Frank Bolz and published by Elsevier. This book was released on 2013-10-22 with total page 344 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Materials in Catalysis is a collection of materials that discusses various catalysts. The book presents the physical and chemical properties that indicate that a particular class of materials may be of catalytic interest. The text first covers bimetallic catalysts, and then proceeds to examining the catalytic properties of compounds such as graphite intercalation compounds; oxides with the scheelite structure; and synthetic layered silicates and aluminosilicate. The book also covers reduction catalysts, biological catalysts, and monolithic catalyst supports. The selection will be of great use to students and practitioners of chemistry, particularly those who are involved in research studies that investigate materials problems in catalysis.
Download or read book Composition Modulation of Catalytic Reactors written by P L Silverton and published by CRC Press. This book was released on 1998-11-26 with total page 650 pages. Available in PDF, EPUB and Kindle. Book excerpt: Composition modulation is a method of operating a catalytic reactor to improve catalyst activity or selectivity and has been under study for more than 25 years. In the last few years, several commercial applications have been realized and more will certainly appear. A large international research literature now exists. This book examines this literature and attempts to organize and analyze it with the intent of identifying the magnitude of improvements possible, why modulation is effective, and what questions remain unanswered. Topics include hydrogenation, oxidation, reduction, and polymerization reactions for NOX, SOX, NH3, and hydrocarbons.
Download or read book Consultant Report to the Committee on Motor Vehicle Emissions Commission on Sociotechnical Systems National Research Council on an Evaluation of Catalytic Converters for Control of Automobile Exhaust Pollutants written by and published by . This book was released on 1974 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Precision Process Technology written by M.P.C. Weijnen and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 722 pages. Available in PDF, EPUB and Kindle. Book excerpt: New process technology strategies are required to cope with the future. Fossil feedstocks are losing ground in favour of renewable feedstocks and secondary resources. Conventional processing routes using thermal `sledgehammer' techniques are replaced by highly selective (bio)catalytic conversions. The future process engineer is neither allowed to think in terms of unit operations, nor to take for granted the conventional practice of continuous steady state processing. Hybrid systems and transient operations are more and more frequently encountered. The continuing impressive progress being made in process modelling and control will revolutionize the process industries. In the new generation of chemical production processes the keyword is precision. Precision in terms of selectivity and of efficiency, is required to maximize the utilisation of materials and energy. Moreover, enhanced precision is needed to exploit the quality of materials and energy to the full extent. Only by reducing the squandering of materials, energy and quality will a harmonious relationship be established between the process industries, the economy, and the environment. Process integration, as well as an integrated effort by the disciplines involved in process technology, will be of crucial importance in attaining the goals of precision process technology. These emerging strategies involve an active exchange of tools and ideas between a variety of disciplines, not only in plant design and operation, but even more in the early stages of process development and design. By looking from various angles at what the future has in store for the process industries, this volume systematically lifts the corners of the veil and may inspire to establish a new tradition of precision in process technology.
