Download or read book Analysis and Design of Matrix Converters for Adjustable Speed Drives and Distributed Power Sources written by Han Ju Cha and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Recently, matrix converter has received considerable interest as a viable alternative to the conventional back-to-back PWM (Pulse Width Modulation) converter in the ac/ac conversion. This direct ac/ac converter provides some attractive characteristics such as: inherent four-quadrant operation; absence of bulky dc-link electrolytic capacitors; clean input power characteristics and increased power density. However, industrial application of the converter is still limited because of some practical issues such as common mode voltage effects, high susceptibility to input power disturbances and low voltage transfer ratio. This dissertation proposes several new matrix converter topologies together with control strategies to provide a solution about the above issues. In this dissertation, a new modulation method which reduces the common mode voltage at the matrix converter is first proposed. The new method utilizes the proper zero vector selection and placement within a sampling period and results in the reduction of the common mode voltage, square rms of ripple components of input current and switching losses. Due to the absence of a dc-link, matrix converter powered ac drivers suffer from input voltage disturbances. This dissertation proposes a new ride-through approach to improve robustness for input voltage disturbances. The conventional matrix converter is modified with the addition of ride-through module and the add-on module provides ride-through capability for matrix converter fed adjustable speed drivers. In order to increase the inherent low voltage transfer ratio of the matrix converter, a new three-phase high-frequency link matrix converter is proposed, where a dual bridge matrix converter is modified by adding a high-frequency transformer into dc-link. The new converter provides flexible voltage transfer ratio and galvanic isolation between input and output ac sources. Finally, the matrix converter concept is extended to dc/ac conversion from ac/ac conversion. The new dc/ac direct converter consists of soft switching full bridge dc/dc converter and three phase voltage source inverter without dc link capacitors. Both converters are synchronized for zero current/voltage switching and result in higher efficiency and lower EMI (Electro Magnetic Interference) throughout the whole load range. Analysis, design example and experimental results are detailed for each proposed topology.

Download or read book Three phase AC AC Power Converters Based on Matrix Converter Topology written by Paweł Szcześniak and published by Springer Science & Business Media. This book was released on 2013-02-28 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: AC voltage frequency changes is one of the most important functions of solid state power converters. The most desirable features in frequency converters are the ability to generate load voltages with arbitrary amplitude and frequency, sinusoidal currents and voltages waveforms; the possibility of providing unity power factor for any load; and, finally, a simple and compact power circuit. Over the past decades, a number of different frequency converter topologies have appeared in the literature, but only the converters with either a voltage or current DC link are commonly used in industrial applications. Improvements in power semiconductor switches over recent years have resulted in the development of many structures of AC-AC converters without DC electric energy storage. Such converters are an alternative solution for frequently recommended systems with DC energy storage and are characterized by a lower price, smaller size and longer lifetime. Most of the these topologies are based on the structure of the matrix converter. Three-Phase AC-AC Power Converters Based On Matrix Converter Topology: Matrix-reactance frequency converters concept presents a review of power frequency converters, with special attention paid to converters without DC energy storage. Particular attention is paid to nine new converters named matrix-reactance frequency converters which have been developed by the author and the team of researchers from Institute of Electrical Engineering at the University of Zielona Góra. The topologies of the presented matrix-reactance frequency converters are based on a three-phase unipolar buck-boost matrix-reactance chopper with source or load switches arranged as in a matrix converter. This kind of approach makes it possible to obtain an output voltage greater than the input one (similar to that in a matrix-reactance chopper) and a frequency conversion (similar to that in a matrix converter). Written for researchers and Ph.D. students working in the field of power electronics converters and drive systems, Three-Phase AC-AC Power Converters Based On Matrix Converter Topology: Matrix-reactance frequency converters concept will also be valuable to power electronics converter designers and users; R&D centers; and readers needing industry solutions in variable speed drive systems, such as automation and aviation.

Download or read book Power Electronics for Renewable Energy Systems Transportation and Industrial Applications written by Haitham Abu-Rub and published by John Wiley & Sons. This book was released on 2014-06-02 with total page 1080 pages. Available in PDF, EPUB and Kindle. Book excerpt: Compiles current research into the analysis and design of power electronic converters for industrial applications and renewable energy systems, presenting modern and future applications of power electronics systems in the field of electrical vehicles With emphasis on the importance and long-term viability of Power Electronics for Renewable Energy this book brings together the state of the art knowledge and cutting-edge techniques in various stages of research. The topics included are not currently available for practicing professionals and aim to enable the reader to directly apply the knowledge gained to their designs. The book addresses the practical issues of current and future electric and plug-in hybrid electric vehicles (PHEVs), and focuses primarily on power electronics and motor drives based solutions for electric vehicle (EV) technologies. Propulsion system requirements and motor sizing for EVs is discussed, along with practical system sizing examples. Key EV battery technologies are explained as well as corresponding battery management issues. PHEV power system architectures and advanced power electronics intensive charging infrastructures for EVs and PHEVs are detailed. EV/PHEV interface with renewable energy is described, with practical examples. This book explores new topics for further research needed world-wide, and defines existing challenges, concerns, and selected problems that comply with international trends, standards, and programs for electric power conversion, distribution, and sustainable energy development. It will lead to the advancement of the current state-of-the art applications of power electronics for renewable energy, transportation, and industrial applications and will help add experience in the various industries and academia about the energy conversion technology and distributed energy sources. Combines state of the art global expertise to present the latest research on power electronics and its application in transportation, renewable energy and different industrial applications Offers an overview of existing technology and future trends, with discussion and analysis of different types of converters and control techniques (power converters, high performance power devices, power system, high performance control system and novel applications) Systematic explanation to provide researchers with enough background and understanding to go deeper in the topics covered in the book

Download or read book Design and Control of Matrix Converters written by Anindya Dasgupta and published by Springer. This book was released on 2017-03-30 with total page 137 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book describes two target applications for synchronous systems: regulated 3-phase voltage supply and voltage sag mitigation. It presents a detailed design procedure for converter switches and filters considering all steady-state, commutation and dynamic requirements. This work has evolved from previously published research by the authors, which in turn is part of a larger effort to expand the application domain of matrix converters to power systems. The objectives of the work have been categorized into the following: developing a dynamic model that provides adequate design insights; designing filters; and devising a control scheme. The low frequency dynamic model is first analyzed for regulated voltage supplies assuming balanced system. The system is modeled relative to a synchronous rotating (dq) frame linearized around an operating point. The input–output variables are related by non-diagonal transfer function matrices. Individual transfer function sub-matrices are sequentially investigated and it is shown that, depending on the input power, input voltage and filter parameters, the appearance of a set of right half zeros is possible. The book then considers filter design, as well as general issues like ripple attenuation, regulation, reactive current loading, and filter losses. The book also addresses additional constraints that may be imposed by dynamic requirements and commutation. In the third stage, voltage controller design is detailed for a 3-phase regulated voltage supply. In dq domain, output voltage control represents a multivariable control problem. This is reduced to a single variable control problem while retaining all possible right half zeros, thereby preserving the internal stability of the system. Consequently, the standard single variable control design technique has been used to design a controller. The analytically predicted dynamic response has been verified by experimental results. It was possible to operate the system beyond the critical power boundary where the right half zeros emerge. Lastly, the developed control approach has been extended to voltage sag mitigation with adequate modifications. A 3-wire linear load and both symmetrical and asymmetrical voltage sags have been considered. Experimentally obtained response time for sag mitigation was found to be less than the power supply holdup time of most of the sensitive equipment. This book will be useful to both researchers and graduate students.

Download or read book High Power Converters and AC Drives written by Bin Wu and published by John Wiley & Sons. This book was released on 2016-12-13 with total page 480 pages. Available in PDF, EPUB and Kindle. Book excerpt: A comprehensive reference of the latest developments in MV drive technology in the area of power converter topologies This new edition reflects the recent technological advancements in the MV drive industry, such as advanced multilevel converters and drive configurations. It includes three new chapters, Control of Synchronous Motor Drives, Transformerless MV Drives, and Matrix Converter Fed Drives. In addition, there are extensively revised chapters on Multilevel Voltage Source Inverters and Voltage Source Inverter-Fed Drives. This book includes a systematic analysis on a variety of high-power multilevel converters, illustrates important concepts with simulations and experiments, introduces various megawatt drives produced by world leading drive manufacturers, and addresses practical problems and their mitigations methods. This new edition: Provides an in-depth discussion and analysis of various control schemes for the MV synchronous motor drives Examines new technologies developed to eliminate the isolation transformer in the MV drives Discusses the operating principle and modulation schemes of matrix converter (MC) topology and multi-module cascaded matrix converters (CMCs) for MV drives, and their application in commercial MV drives Bin Wu is a Professor and Senior NSERC/Rockwell Automation Industrial Research Chair in Power Electronics and Electric Drives at Ryerson University, Canada. He is a fellow of Institute of Electrical and Electronics Engineers (IEEE), Engineering Institute of Canada (EIC), and Canadian Academy of Engineering (CAE). Dr. Wu has published more than 400 papers and holds more than 30 granted/pending US/European patents. He co-authored several books including Power Conversion and Control of Wind Energy Systems and Model Predictive Control of Wind Energy Conversion Systems (both by Wiley-IEEE Press). Mehdi Narimani is a Postdoctoral Research Associate with the Department of Electrical and computer Engineering at Ryerson University, Canada, and Rockwell Automation Canada. He is a senior member of IEEE. Dr. Narimani is author/co-author of more than 50 technical papers and four US/European patents (issued/pending review). His current research interests include power conversion, high power converters, control of power electronics, and renewable energy systems.

Download or read book Dissertation Abstracts International written by and published by . This book was released on 2006 with total page 848 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Modeling and Control of Power Electronic Converters for Microgrid Applications written by Yang Han and published by Springer Nature. This book was released on 2021-08-27 with total page 322 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers the fundamentals of power electronic converter modeling and control, digital simulation, and experimental studies in the area of renewable energy systems and AC/DC microgrid. Recent advanced control methods for voltage source inverters (VSIs) and the hierarchical controlled islanded microgrid are discussed, including the mathematical modeling, controller synthesis, parameter selection and multi-scale stability analysis, and consensus-based control strategies for the microgrid and microgrid clusters. The book will be an invaluable technical reference for practicing engineers and researchers working in the areas of renewable energy, power electronics, energy internet, and smart grid. It can also be utilized as reference book for undergraduate and postgraduate students in electrical engineering.

Download or read book Impedance Source Matrix Converters and Control written by Liu and published by Wiley-Blackwell. This book was released on 2024-10-30 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Emerging Power Converters for Renewable Energy and Electric Vehicles written by Md. Rabiul Islam and published by CRC Press. This book was released on 2021-05-30 with total page 419 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers advancements of power electronic converters and their control techniques for grid integration of large-scale renewable energy sources and electrical vehicles. Major emphasis is on transformer-less direct grid integration, bidirectional power transfer, compensation of grid power quality issues, DC system protection and grounding, interaction in mixed AC/DC systems, AC and DC system stability, design of high-frequency high power density systems with advanced soft magnetic materials, modeling and simulation of mixed AC/DC systems, switching strategies for enhanced efficiency, and protection and reliability for sustainable grid integration. This book is an invaluable resource for professionals active in the field of renewable energy and power conversion. Md. Rabiul Islam received his PhD from the University of Technology Sydney (UTS), Australia. He was appointed as a Lecturer at Rajshahi University of Engineering & Technology (RUET) in 2005 and promoted to full-term Professor in 2017. In early 2018, he joined the School of Electrical, Computer, and Telecommunications Engineering, University of Wollongong, Australia. He is a Senior Member of IEEE. His research interests include the fields of power electronic converters, renewable energy technologies, power quality, electrical machines, electric vehicles, and smart grids. He has authored or coauthored more than 200 publications including 50 IEEE Transactions/IEEE Journal papers. He has been serving as an editor for IEEE Transactions on Energy Conversion and IEEE Power Engineering Letters, and associate editor for IEEE Access. Md. Rakibuzzaman Shah is a Senior Lecturer with the School of Engineering, Information Technology and Physical Science at Federation University Australia. He has worked and consulted with distribution network operators and transmission system operators on individual projects and has done collaborative work on a large number of projects (EPSRC project on multi-terminal HVDC, Scottish and Southern Energy multi-infeed HVDC) - primarily on the dynamic impact of integrating new technologies and power electronics into large systems. He is an active member of the IEEE and CIGRE. He has more than 70 international publications and has spoken at the leading power system conferences around the world. His research interests include future power grids (i.e., renewable energy integration, wide-area control), asynchronous grid connection through VSC-HVDC, application of data mining in power system, distribution system energy management, and low carbon energy systems. Mohd. Hasan Ali is currently an Associate Professor with the Electrical and Computer Engineering Department at the University of Memphis, USA, where he leads the Electric Power and Energy Systems (EPES) Laboratory. His research interests include advanced power systems, smart-grid and microgrid systems, renewable energy systems, and cybersecurity issues in modern power grids. Dr. Ali has more than 190 publications, including 2 books, 4 book chapters, 2 patents, 60 top ranked journal papers, 96 peer-reviewed international conference papers, and 20 national conference papers. He serves as the editor of the IEEE Transactions on Sustainable Energy and IET-Generation, Transmission and Distribution (GTD) journal. Dr. Ali is a Senior Member of the IEEE Power and Energy Society (PES). He is also the Chair of the PES of the IEEE Memphis Section.

Download or read book Power Electronics for Renewable and Distributed Energy Systems written by Sudipta Chakraborty and published by Springer Science & Business Media. This book was released on 2013-06-12 with total page 612 pages. Available in PDF, EPUB and Kindle. Book excerpt: While most books approach power electronics and renewable energy as two separate subjects, Power Electronics for Renewable and Distributed Energy Systems takes an integrative approach; discussing power electronic converters topologies, controls and integration that are specific to the renewable and distributed energy system applications. An overview of power electronic technologies is followed by the introduction of various renewable and distributed energy resources that includes photovoltaics, wind, small hydroelectric, fuel cells, microturbines and variable speed generation. Energy storage systems such as battery and fast response storage systems are discussed along with application-specific examples. After setting forth the fundamentals, the chapters focus on more complex topics such as modular power electronics, microgrids and smart grids for integrating renewable and distributed energy. Emerging topics such as advanced electric vehicles and distributed control paradigm for power system control are discussed in the last two chapters. With contributions from subject matter experts, the diagrams and detailed examples provided in each chapter make Power Electronics for Renewable and Distributed Energy Systems a sourcebook for electrical engineers and consultants working to deploy various renewable and distributed energy systems and can serve as a comprehensive guide for the upper-level undergraduates and graduate students across the globe.

Download or read book Design and Control of Power Converters 2020 written by Manuel Arias and published by MDPI. This book was released on 2021-06-04 with total page 188 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this book, nine papers focusing on different fields of power electronics are gathered, all of which are in line with the present trends in research and industry. Given the generality of the Special Issue, the covered topics range from electrothermal models and losses models in semiconductors and magnetics to converters used in high-power applications. In this last case, the papers address specific problems such as the distortion due to zero-current detection or fault investigation using the fast Fourier transform, all being focused on analyzing the topologies of high-power high-density applications, such as the dual active bridge or the H-bridge multilevel inverter. All the papers provide enough insight in the analyzed issues to be used as the starting point of any research. Experimental or simulation results are presented to validate and help with the understanding of the proposed ideas. To summarize, this book will help the reader to solve specific problems in industrial equipment or to increase their knowledge in specific fields.

Download or read book Switch Mode Power Converters written by Keng C. Wu and published by Elsevier. This book was released on 2005-12-01 with total page 409 pages. Available in PDF, EPUB and Kindle. Book excerpt: Switch-Mode Power Converters introduces an innovative, highly analytical approach to symbolic, closed-form solutions for switched-mode power converter circuits. This is a highly relevant topic to power electronics students and professionals who are involved in the design and analysis of electrical power converters. The author uses extensive equations to explain how solid-state switches convert electrical voltages from one level to another, so that electronic devices (e.g., audio speakers, CD players, DVD players, etc.) can use different voltages more effectively to perform their various functions. Most existing comparable books published as recently as 2002 do not discuss closed-loop operations, nor do they provide either DC closed-loop regulation equations or AC loop gain (stability) formulae. The author Wu, a leading engineer at Lockheed Martin, fills this gap and provides among the first descriptions of how error amplifiers are designed in conjunction with closed-loop bandwidth selection. BENEFIT TO THE READER: Readers will gain a mathematically rigorous introduction to numerous, closed-form solutions that are readily applicable to the design and development of various switch-mode power converters. - Provides symbolic, closed-form solutions for DC and AC studies - Provides techniques for expressing close-loop operation - Gives readers the ability to perform closed-loop regulation and sensitivity studies - Gives readers the ability to design error amplifiers with precision - Employs the concept of the continuity of states in matrix form - Gives accelerated time-domain, steady-state studies using Laplace transform - Gives accelerated time-domain studies using state transition - Extensive use of matrix, linear algebra, implicit functions, and Jacobian determinants - Enables the determination of power stage gain that otherwise could not be obtained

Download or read book Advanced Matrix Converters written by Hui Wang and published by Springer. This book was released on 2024-10-26 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced Matrix Converters: Topology, Modulation, and Control is a comprehensive guide for readers interested in developing advanced direct AC-AC converters, commonly known as matrix converters (MCs). These MCs offer an all-silicon and environmentally friendly solution that has garnered increasing attention in recent years due to their ability to eliminate bulky passive components and improve the converters' power density, conversion efficiency, and reliability. This book covers the principles of topology construction, advanced modulation strategies, application areas, and control methods. It includes topics such as efficient AC-AC conversion, multi-level conversion, and high-performance adjustable speed drives. It is an essential resource for researchers, engineers, and designers who must select the most appropriate new topologies and control methods for specific applications.

Download or read book Analysis Design and Applications of Switched capacitor Converters written by Chun Kit Cheung and published by . This book was released on 2016 with total page 171 pages. Available in PDF, EPUB and Kindle. Book excerpt: Second, a universal SC converter capable of achieving DC-DC, AC-DC and DC-AC power conversions is proposed. Previous SC converters are designed and are only applicable to some particular applications, which are unsuitable for application in situations requiring multi-purpose power conversions. A multi conversion purpose SC converter can resolve the problem. Detailed circuit operations on each type of power conversions are described. The control methodology of the overall system is explained. The required circuitries for programming the control sequence of power switches for achieving various types of power conversions are given. Simulations have been performed to a preliminary proof of the proposed idea. An experimental prototype has been built to demonstrate the proposed idea. It is shown that different types of power conversions can be achieved by only adjusting the control signals of power MOSFETs. Both line and load regulations capabilities, efficiency analysis, and dynamic response under the step change of the load current of the proposed converter are discussed. Third, a multi-port SC converter is introduced for multiple sources or loads applications. Due to the distributed energy resources (DER) characteristic in renewable energy systems, multiple converters are required for different power conversions in the entire system. An alternative approach is proposed to resolve the aforementioned problem, which is through the means of using a multi-port SC converter. The multi-port structure of the proposed SC converter allows the connections of different power sources or loads to a single SC converter, while different power conversions among the connected sources and loads can be performed. An example of an energy system having photovoltaic (PV) panel, battery, and AC voltage grid is considered to discuss the feasibility of the proposed converter. Three different operating modes, including the battery recharging by the PV panel or the AC voltage source, and the AC voltage generation from the PV panel, are defined. Detailed explanations on different operating modes and the overall control methodology are given. Simulation results and experimental verifications, including the line and load regulation capabilities, the efficiency analysis, and the transient response, are given. It has been shown that different power conversions among the connected sources or loads can be readily achieved by using only a single SC converter. This thesis contains seven chapters. The first three chapters give respectively the introduction of the thesis, a literature review on the previous works, and an overview of the SC converters. The accomplished research works in this study are discussed in Chapters 4-6. The objective, theoretical analysis, and experimental verifications of each work are included. The last chapter gives a conclusion to the thesis and a discussion on some possible future works.

Download or read book Impedance Source Power Electronic Converters written by Yushan Liu and published by John Wiley & Sons. This book was released on 2016-08-22 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt: Impedance Source Power Electronic Converters brings together state of the art knowledge and cutting edge techniques in various stages of research related to the ever more popular impedance source converters/inverters. Significant research efforts are underway to develop commercially viable and technically feasible, efficient and reliable power converters for renewable energy, electric transportation and for various industrial applications. This book provides a detailed understanding of the concepts, designs, controls, and application demonstrations of the impedance source converters/inverters. Key features: Comprehensive analysis of the impedance source converter/inverter topologies, including typical topologies and derived topologies. Fully explains the design and control techniques of impedance source converters/inverters, including hardware design and control parameter design for corresponding control methods. Presents the latest power conversion solutions that aim to advance the role of power electronics into industries and sustainable energy conversion systems. Compares impedance source converter/inverter applications in renewable energy power generation and electric vehicles as well as different industrial applications. Provides an overview of existing challenges, solutions and future trends. Supported by calculation examples, simulation models and results. Highly accessible, this is an invaluable resource for researchers, postgraduate/graduate students studying power electronics and its application in industry and renewable energy conversion as well as practising R&D engineers. Readers will be able to apply the presented material for the future design of the next generation of efficient power electronic converters/inverters.

Download or read book Predictive Control of Power Converters and Electrical Drives written by Jose Rodriguez and published by Wiley-IEEE Press. This book was released on 2012-04-30 with total page 246 pages. Available in PDF, EPUB and Kindle. Book excerpt: Describes the general principles and current research into Model Predictive Control (MPC); the most up-to-date control method for power converters and drives The book starts with an introduction to the subject before the first chapter on classical control methods for power converters and drives. This covers classical converter control methods and classical electrical drives control methods. The next chapter on Model predictive control first looks at predictive control methods for power converters and drives and presents the basic principles of MPC. It then looks at MPC for power electronics and drives. The third chapter is on predictive control applied to power converters. It discusses: control of a three-phase inverter; control of a neutral point clamped inverter; control of an active front end rectifier, and; control of a matrix converter. In the middle of the book there is Chapter four - Predictive control applied to motor drives. This section analyses predictive torque control of industrial machines and predictive control of permanent magnet synchronous motors. Design and implementation issues of model predictive control is the subject of the final chapter. The following topics are described in detail: cost function selection; weighting factors design; delay compensation; effect of model errors, and prediction of future references. While there are hundreds of books teaching control of electrical energy using pulse width modulation, this will be the very first book published in this new topic. Unique in presenting a completely new theoretic solution to control electric power in a simple way Discusses the application of predictive control in motor drives, with several examples and case studies Matlab is included on a complementary website so the reader can run their own simulations

Download or read book High Efficiency Power Supply Using New SiC Devices written by Ashot Melkonyan and published by kassel university press GmbH. This book was released on 2007 with total page 159 pages. Available in PDF, EPUB and Kindle. Book excerpt: