Download or read book An Introduction to the Ballistics Technical Design of Ammunition written by Paul F. Kisak and published by CreateSpace. This book was released on 2015-01-04 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual is designed to show the "best of the best" ballistics and loading data. The manual is also designed to compare the performance and design characteristics of over 200 popular rounds of ammunition based on maximum muzzle velocity. The manual gives an introduction to the following: 1.) The background, notes, assumptions and formulas used when calculating the ballistic characteristics of ammunition. 2.) Individual tables of ammunition characteristics for over 200 calibers or rounds of ammunition. 3.) A Chart of Gun Powder burn rates. 4.) An Overview of Explosives. 5.) Several Emergency and Survival Preparedness Guides The Following Characteristics are explained and listed in the manual for ease of comparison between rounds (for example - comparing the Optimum Take-down Weight of a .223 vs. 7.62 x 39 mm): Bullet Weight ( Grains): Cartridge Charge (Grains): Muzzle Speed (feet per second): Actual Chamber Pressure in (CUP's): Maximum Allowable SAAMI Pressure (CUP's): Accurate PowderTM Type: Bullet Type (i.e. FMJ, JHP, SWG, etc.): Maximum Cartridge Length (inches): Brass Length (inches): Bullet Length (inches): Bullet Width (inches): Muzzle Energy (foot-pounds): Recoil Impulse I (pound-seconds): Free Recoil Speed VG (feet per second): "Kick" - Free Recoil Energy EG (foot-pounds): Minimum Length of Twist Required for Optimum Stability (inches): Density of Loading: The Rotational Speed in RPM (Revolutions per second): Prof. Hunter John Taylor's Knockout Blow: Sectional Density: Editor John Wooter's L-factor: Ballistic Expert Ed Matuna's Optimum Takedown Game Weight (pounds): Momentum (pounds - feet per second): Maximum Potential Energy of Ignited Powder (foot-pounds): Efficiency of Maximum Energy Produced (%): Average Speed of Bullet in the Barrel (feet per second): Average Pressure on the Bullet in the Barrel (CUP's): Average Energy of the Bullet in the Barrel (foot-pounds): Approximate Ballistic Coefficient: Absolute Effective Range at Sea Level (feet): Absolute Effective Range with 10 mph Tail Wind (feet): Representative Weight of Weapon (pounds): Ratio of Muzzle Energy to Weight of Weapon (%): Bullet Drop at various ranges:
Download or read book Know Your Ammo the Ballistics and Technical Design of Ammunition written by Paul Kisak and published by CreateSpace. This book was released on 2015-10-16 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Know Your Ammo" is designed to show the "best of the best" ballistics and loading data. The manual is also designed to compare the performance and design characteristics of over 200 popular rounds of ammunition based on maximum muzzle velocity. The manual gives an introduction to the following : 1.) The background, notes, assumptions and formulas used when calculating the ballistic characteristics of ammunition. 2.) Individual tables of ammunition characteristics for over 200 calibers or rounds of ammunition. 3.) A Chart of Gun Powder burn rates. 4.) An Overview of Explosives. 5.) Several Emergency and Survival Preparedness GuidesThe Following Characteristics are explained and listed in the manual for ease of comparison between rounds (for example - comparing the Optimum Take-down Weight of a .223 vs. 7.62 x 39 mm):Bullet Weight ( Grains) :Cartridge Charge (Grains) :Muzzle Speed (feet per second) :Actual Chamber Pressure in (CUP's) :Maximum Allowable SAAMI Pressure (CUP's) :Accurate PowderTM Type :Bullet Type (i.e. FMJ, JHP, SWG, etc.) : Maximum Cartridge Length (inches) :Brass Length (inches) :Bullet Length (inches) :Bullet Width (inches) :Muzzle Energy (foot-pounds) :Recoil Impulse I (pound-seconds) :Free Recoil Speed VG (feet per second) :"Kick" - Free Recoil Energy EG (foot-pounds) :Minimum Length of Twist Required for Optimum Stability (inches) :Density of Loading :The Rotational Speed in RPM (Revolutions per second) :Prof. Hunter John Taylor's Knockout Blow :Sectional Density :Editor John Wooter's L-factor :Ballistic Expert Ed Matuna's Optimum Takedown Game Weight (pounds) :Momentum (pounds - feet per second) :Maximum Potential Energy of Ignited Powder (foot-pounds) :Efficiency of Maximum Energy Produced (%) :Average Speed of Bullet in the Barrel (feet per second) :Average Pressure on the Bullet in the Barrel (CUP's) :Average Energy of the Bullet in the Barrel (foot-pounds) :Approximate Ballistic Coefficient :Absolute Effective Range at Sea Level (feet) :Absolute Effective Range with 10 mph Tail Wind (feet) :Representative Weight of Weapon (pounds) :Ratio of Muzzle Energy to Weight of Weapon (%) :Bullet Drop at various ranges :
Download or read book Know Your Ammo the Ballistics and Technical Design of Ammunition written by Paul F. Kisak and published by CreateSpace. This book was released on 2015-06-10 with total page 278 pages. Available in PDF, EPUB and Kindle. Book excerpt: "Know Your Ammo" is designed to show the "best of the best" ballistics and loading data. The manual is also designed to compare the performance and design characteristics of over 200 popular rounds of ammunition based on maximum muzzle velocity. The manual gives an introduction to the following : 1.) The background, notes, assumptions and formulas used when calculating the ballistic characteristics of ammunition. 2.) Individual tables of ammunition characteristics for over 200 calibers or rounds of ammunition. 3.) A Chart of Gun Powder burn rates. 4.) An Overview of Explosives. 5.) Several Emergency and Survival Preparedness Guides The Following Characteristics are explained and listed in the manual for ease of comparison between rounds (for example - comparing the Optimum Take-down Weight of a .223 vs. 7.62 x 39 mm): Bullet Weight ( Grains) : Cartridge Charge (Grains) : Muzzle Speed (feet per second) : Actual Chamber Pressure in (CUP's) : Maximum Allowable SAAMI Pressure (CUP's) : Accurate PowderTM Type : Bullet Type (i.e. FMJ, JHP, SWG, etc.) : Maximum Cartridge Length (inches) : Brass Length (inches) : Bullet Length (inches) : Bullet Width (inches) : Muzzle Energy (foot-pounds) : Recoil Impulse I (pound-seconds) : Free Recoil Speed VG (feet per second) : "Kick" - Free Recoil Energy EG (foot-pounds) : Minimum Length of Twist Required for Optimum Stability (inches) : Density of Loading : The Rotational Speed in RPM (Revolutions per second) : Prof. Hunter John Taylor's Knockout Blow : Sectional Density : Editor John Wooter's L-factor : Ballistic Expert Ed Matuna's Optimum Takedown Game Weight (pounds) : Momentum (pounds - feet per second) : Maximum Potential Energy of Ignited Powder (foot-pounds) : Efficiency of Maximum Energy Produced (%) : Average Speed of Bullet in the Barrel (feet per second) : Average Pressure on the Bullet in the Barrel (CUP's) : Average Energy of the Bullet in the Barrel (foot-pounds) : Approximate Ballistic Coefficient : Absolute Effective Range at Sea Level (feet) : Absolute Effective Range with 10 mph Tail Wind (feet) : Representative Weight of Weapon (pounds) : Ratio of Muzzle Energy to Weight of Weapon (%) : Bullet Drop at various ranges :
Download or read book Ballistics written by Donald E. Carlucci and published by CRC Press. This book was released on 2013-08-26 with total page 598 pages. Available in PDF, EPUB and Kindle. Book excerpt: Providing new chapters, homework problems, case studies, figures, and examples, Ballistics: Theory and Design of Guns and Ammunition, Second Edition encourages superior design and innovative applications in the field of ballistics. It examines the analytical and computational tools used to predict a weapon’s behavior in terms of pressure, stress, and velocity, demonstrating their applications in ammunition and weapons design. What’s New in the Second Edition: Includes computer examples in Mathcad (available on the CRC website) Adds a section of color plates, to better help readers visualize the physical concepts of ballistics Contains sections on modern explosives equations of state for detonation physics modeling and on probability of hit Provides a solutions manual for those teaching college and training courses This book covers exterior ballistics, exploring the physics behind trajectories, including linear and nonlinear aeroballistics, and focuses on the effects of projective impact, including details on shock physics, shaped charges, penetration, fragmentation, and wound ballistics. Reviews and integrates the fundamental science and engineering concepts involved in guns and ammunition Uses straightforward, easy-to-read style, and careful development of complex topics Shares insights rooted in the experience of renowned experts, many associated with the National Defense Industrial Association (NDIA) and International Ballistics Society The field of ballistics comprises three main areas of specialization: interior, exterior, and terminal ballistics. This book explains all three areas, offering a seamless presentation of the complex phenomena that occur during the launch, flight, and impact of a projectile.
Download or read book Ballistics written by Donald E. Carlucci and published by CRC Press. This book was released on 2007-12-14 with total page 514 pages. Available in PDF, EPUB and Kindle. Book excerpt: Even the earliest weapon developers faced the need to understand how and why guns and ammunition work in order to improve their effectiveness. As weapons became more sophisticated, the field of ballistics naturally divided into three main areas of specialization: interior, exterior, and terminal ballistics. Providing unique coverage of all three ar
Download or read book Ballistics written by Donald E. Carlucci and published by CRC Press. This book was released on 2018-03-15 with total page 642 pages. Available in PDF, EPUB and Kindle. Book excerpt: With new chapters, homework problems, case studies, figures, and examples, Ballistics: Theory and Design of Guns and Ammunition, Third Edition encourages superior design and innovative applications in the field of ballistics. It examines the analytical and computational tools for predicting a weapon’s behavior in terms of pressure, stress, and velocity, demonstrating their applications in ammunition and weapons design. New coverage in the Third Edition includes gas-powered guns, and naval ordinance. With its thorough coverage of interior, exterior and terminal ballistics, this new edition continues to be the standard resource for those studying the technology of guns and ammunition.
Download or read book Ballistics written by Donald E. Carlucci and published by CRC Press. This book was released on 2018-03-15 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: With new chapters, homework problems, case studies, figures, and examples, Ballistics: Theory and Design of Guns and Ammunition, Third Edition encourages superior design and innovative applications in the field of ballistics. It examines the analytical and computational tools for predicting a weapon’s behavior in terms of pressure, stress, and velocity, demonstrating their applications in ammunition and weapons design. New coverage in the Third Edition includes gas-powered guns, and naval ordinance. With its thorough coverage of interior, exterior and terminal ballistics, this new edition continues to be the standard resource for those studying the technology of guns and ammunition.
Download or read book An Introduction to the Ballistics of Firearms written by Edited by Paul F. Kisak and published by . This book was released on 2016-02-28 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: This introduction to ballistics is an overview of the essentials involved in the mathematical modeling of the ballistics that pertain to a bullet that is fired from a firearm. This book gives an overview into the classical mechanics of ballistics which includes everything from the internal, transitional, external and terminal ballistics to the equations of motion, trajectory, hydrostatic shock and Stokes' Law. Included are sections on ranged weapons, propellants, firearm, bullet and barrel design. A section on stopping power is especially noteworthy as this is often the factor that drives the design of the weapon. This edition also includes some of the latest ballistics studies from the war in Iraq. Also see "Know Your Ammo!" - An Introduction to the Ballistics & Technical Design of Ammunition at https://www.createspace.com/5804109. & " A Comprehensive Guide to Handgun Ammunition " at https://www.createspace.com/6010094" A Comprehensive Guide to Rifle Ammunition Vol. 1 " - https://www.createspace.com/6098488" A Comprehensive Guide to Rifle Ammunition Vol. 2 " - https://www.createspace.com/6098527" A Comprehensive Guide to Munitions " - https://www.createspace.com/6009915
Download or read book Engineering Design Handbook Gun Series written by Army Material Army Material Command and published by Createspace Independent Publishing Platform. This book was released on 2018-03-04 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: Part of the Army Material Commands series on gun design. This book is a must have for anyone interested in the actual design that goes into any firearm.
Download or read book An Introduction to the Ballistics of Firearms written by Edited by Paul Kisak and published by Createspace Independent Publishing Platform. This book was released on 2014-11-27 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This introduction to ballistics is an overview of the essentials involved in the mathematical modeling of the ballistics that pertain to a bullet that is fired from a firearm. This book gives an overview into the classical mechanics of ballistics which includes everything from the internal, transitional, external and terminal ballistics to the equations of motion, trajectory, hydrostatic shock and Stokes' Law.Included are sections on ranged weapons, propellants, firearm, bullet and barrel design.A section on stopping power is especially noteworthy as this is often the factor that drives the design of the weapon.This edition also includes some of the latest ballistics studies from the war in Iraq.Also see these classics:"Know Your Ammo!" Manual & Guide to Reloading & Comparing the 'Best of the Best' Loads. - https://www.createspace.com/5804109 - $19.95 - 268 pagesThe Basics of Firearms - https://www.createspace.com/6600673 - $19.95 - 214 pagesA Comprehensive Guide to Handgun Ammunition - https://www.createspace.com/6010094 - $19.95 - 510 pagesA Comprehensive Guide to Rifle Ammunition Vol. 1 - https://www.createspace.com/6098488 - $24.95 - 446 pagesA Comprehensive Guide to Rifle Ammunition Vol. 2 - https://www.createspace.com/6098527- $24.95 - 566 pagesThe Basics of Explosives Vol. 1 - https://www.createspace.com/6634824- $19.95 - 246 pagesThe Basics of Explosives Vol. 2 - https://www.createspace.com/6634867- $19.95 - 214 pagesA Comprehensive Guide to Munitions - https://www.createspace.com/6009915- $19.95 - 402 pagesMilitary History - https://www.createspace.com/5850454- $19.95 - 292 pages U.S. Special Operations Command - https://www.createspace.com/6037278- $19.95 - 214 pagesWarfare - https://www.createspace.com/5840104- $19.95 - 402 pages
Download or read book A Comprehensive Guide to Rifle Ammunition Vol 2 Of 2 written by Paul F. Kisak and published by Createspace Independent Publishing Platform. This book was released on 2016-02-15 with total page 566 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rifle Ammunition (commonly shortened to ammo) is propellant and projectile, or broadly anything that can be used in combat and fired from a rifled firearm. The purpose of ammunition is to project force against a selected target. However, the nature of ammunition use also includes delivery or combat supporting munitions such as pyrotechnic or incendiary compounds. Since the design of the cartridge, the meaning has been transferred to the assembly of a projectile and its propellant in a single package. Ammunition involves the application of fire to targets, general use of weapons by personnel, explosives and propellants, cartridge systems, high explosive projectiles (HE), warheads, shaped charge forms of attack on armour and aircraft, carrier projectiles, fuzes, mortar ammunition, small arms ammunition, grenades, mines, pyrotechnics, improved conventional munitions, and terminally guided munition. A "round" is a term synonymous with a single cartridge containing a projectile, propellant, primer and casing. This book focuses on the rifle cartridge, its history, dimensions, construction, assembly and use. This volume 2 of 2 focuses on 150 Cartridges larger than 50 cal. Including Metric Cartridges. You can purchase volume 1 which discusses 132 rounds under 39 caliber at https: //www.createspace.com/ 6098488.
Download or read book The Science of Small Arms Ballistics written by Alvah Buckmore, Jr. and published by CRC Press. This book was released on 2018-07-17 with total page 202 pages. Available in PDF, EPUB and Kindle. Book excerpt: The science of small arms ballistics is seriously underdeveloped and underappreciated. This unique and different book is a comprehensive study that fills a legitimate need for a work that covers the engineering and theory of small arms ballistics. The author shares his extensive research on working out the science of small arm ballistics mathematically and explains his theories, such as the field-effect and the field-effect over trajectory and time, along with new theories on interior, exterior, and terminal ballistics. Each equation describes a mathematical relationship, such as transfer of energy, and has an engineering application to help solve a design problem. Some equations, such as the calculation of bullet length with a given muzzle velocity and rate of twist, represent manipulations of those equations. Some other equations represent a set of mathematical instructions to resolve a technical problem, such as the computation of trajectory or depth of penetration of living tissue in real-time.
Download or read book TOP GUNS Ammunition Ballistics Explosives and Survival Preparedness Manual written by Paul F. Kisak and published by Createspace Independent Pub. This book was released on 2014-10-01 with total page 268 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Top Guns(tm) manual is in the 5th edition and was created and reviewed by experts in their field. The manual is easy to read and use. With the Top Guns(tm) manual you can educate yourself and become an expert in the field of practical ballistics.The "Top Guns (tm)" Ammunition, Ballistics, Explosives & Survivor Preparedness Manual is used to compare and understand the performance and design characteristics of numerous popular rounds of ammunition & explosives. The "TOP GUNS (tm) Manual explains the following: 1.) The background, notes, assumptions and formulas used when calculating the ballistic characteristics. 2.) The individual tables of characteristics for each round based on the values listed such as bullet weight, cartridge charge and powder type. The ballistic calculations involve a variety of equations that seek to predict the behavior and characteristics of the round being fired. The ballistic equations are divided into 1.) Internal Ballistics and 2.) External Ballistics. 3.) A Chart of Gun Powder Burn Rates & Sniper & Downrange cards 4.) An Overview of Explosives 5.) Several Emergency & Survival Preparedness Guides There are nearly 10,000 different kinds of firearms being used in over 150 countries the origins of which date back to the 1600's. These firearms all have one thing in common. The firearm is a complex balance of chemistry, physics, optics, metallurgy and ergonomics. These fields of science are used to design an efficient handheld device that has the metallurgy utilized in such a manner that the firearm barrel and mechanics can withstand the chemical explosion of the gunpowder and propel a round down range in a manner accurate enough to hit a target. This same firearm must also employ the physics of ballistics that produces a bullet that leaves the barrel with the correct amount of spin in order to stabilize the bullet in flight. The firearm must also have a design that employs the exacting physics that allows the energy and pressure of the chemical explosion to propel the bullet through the rifled barrel, use this same energy to eject the casing, cycle the action and repeat this thousands of times using a frame that is lightweight and convenient to aim and carry. The optics must be such that it allows the human eye to focus on a point down-range, usually in order to deliver a bullet reliably on target, whenever needed. All of the above, involve extensive functional decomposition, mathematical modeling and ballistics calculations and testing, in order to produce a reliable mass-produced weapon. Ballistic calculations involve a variety of equations that seek to predict the behavior and characteristics of the round being fired. The equations are usually divided into 1.) Internal Ballistics 2.) Transitional Ballistics 3.) External Ballistics and 4. Terminal Ballistics.The Top Guns (tm) Manual will educate you on the ballistics, the calculations and terms used in designing ammunition.
Download or read book A Comprehensive Guide to Rifle Ammunition Vol 1 Of 2 written by Paul F. Kisak and published by Createspace Independent Publishing Platform. This book was released on 2016-02-15 with total page 446 pages. Available in PDF, EPUB and Kindle. Book excerpt: Rifle Ammunition (commonly shortened to ammo) is propellant and projectile, or broadly anything that can be used in combat and fired from a rifled firearm. The purpose of ammunition is to project force against a selected target. However, the nature of ammunition use also includes delivery or combat supporting munitions such as pyrotechnic or incendiary compounds. Since the design of the cartridge, the meaning has been transferred to the assembly of a projectile and its propellant in a single package. Ammunition involves the application of fire to targets, general use of weapons by personnel, explosives and propellants, cartridge systems, high explosive projectiles (HE), warheads, shaped charge forms of attack on armour and aircraft, carrier projectiles, fuzes, mortar ammunition, small arms ammunition, grenades, mines, pyrotechnics, improved conventional munitions, and terminally guided munition. A "round" is a term synonymous with a single cartridge containing a projectile, propellant, primer and casing. This book focuses on the rifle cartridge, its history, dimensions, construction, assembly and use. This volume 1 focuses on 132 rounds under 39 caliber. You can purchase volume 2 which discusses 150 Cartridges larger than 50cal. Including Metric Cartridges at https: //www.createspace.com/ 6098527.
Download or read book Textbook of Pistols and Revolvers written by Julian S. Hatcher and published by Simon and Schuster. This book was released on 2015-01-27 with total page 715 pages. Available in PDF, EPUB and Kindle. Book excerpt: Originally published in 1935, Textbook of Pistols and Revolvers is a treatise on handguns of the early twentieth century. Written by Major Julian S. Hatcher, an expert on the subject of firearms of all sorts, readers will gain invaluable insight into everything to do with handheld firearms of the 1930s. In his introduction, Hatcher emphasizes that he has made an earnest effort to make this book accessible for both novices and experts. Novices who know nothing whatsoever about firearms and their use can easily learn from this book, while experts will find a technical reference book where “the results of many experiments with pistols and revolvers and their ammunition are tabulated in convenient form.” Covering such subjects as the different methods of shooting and using hand firearms; their mechanism, care and repair; their interior and exterior ballistics; the peculiar suitability of the different kinds for various purposes; the relative effectiveness or stopping power of the various calibers and types of gun and ammunition; and many more, this book is an immense store of knowledge on early handguns. Skyhorse Publishing is proud to publish a broad range of books for hunters and firearms enthusiasts. We publish books about shotguns, rifles, handguns, target shooting, gun collecting, self-defense, archery, ammunition, knives, gunsmithing, gun repair, and wilderness survival. We publish books on deer hunting, big game hunting, small game hunting, wing shooting, turkey hunting, deer stands, duck blinds, bowhunting, wing shooting, hunting dogs, and more. While not every title we publish becomes a New York Times bestseller or a national bestseller, we are committed to publishing books on subjects that are sometimes overlooked by other publishers and to authors whose work might not otherwise find a home.
Download or read book Ammo and Ballistics 6 for Hunters Shooters and Collectors written by Robert Forker and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The entirely updated and revised Ammo & Ballistics 6 is now available and is better than ever! Ammo & Ballistics 6 contains data and illustrations on virtually every sporting cartridge sold in the USA. Besides clear and concise writing that clarifies the complexities of ballistic coefficients and energy versus momentum, this revised edition covers 200-plus calibers . . . from the .17 Mach 2 to the .700 Nitro Express. It contains information on rifle and handgun calibers, and it covers manufacturers, bullet weights, types, and construction. In addition, each caliber has an exact technical drawing with all dimensions and angles. There are over 3,000 tables with ballistic data for every caliber and every load for all commercially loaded hunting ammunition sold in the United States. Tables include velocity, energy, wind drift, bullet drop, and ballistic coefficients up to 1,000 yards. Manufacturers include A-Square, Aguila, ATK, Black Hills, CCI/Speer, Cor-Bon Bullet, Dakota Arms, Eley Ltd., Federal Cartridge, Fiocchi, Hirtenberger, Hornady, Patria Lapua Oy, Lazzeroni, Kynoch (Kynamco Ltd.), MagTech, Norma, Nosler, Inc., PMC (Eldorado Cartridge Corp.), Remington, Dynamit (Nobel-RWS Inc.), Sellier and Bellot, Ultramax, Weatherby, and Winchester. If you want to know where you will be hitting at long distances, this is the book for you. This book is, quite literally, indispensable for the hunter or shooter.
Download or read book A Comprehensive Guide to Munitions written by Paul F. Kisak and published by Createspace Independent Publishing Platform. This book was released on 2016-01-18 with total page 402 pages. Available in PDF, EPUB and Kindle. Book excerpt: Munitions are anything that can be used in combat including bullets, bombs, missiles, warheads, mines, artillery and rockets. Munitions is the collective term for all material used in war. The purpose of munitions is to project force against a selected target. However, the nature of munitions includes delivery or combat supporting munitions such as pyrotechnic or incendiary compounds. Since the design of the cartridge, the meaning has been transferred to the assembly of a projectile and its propellant in a single package. Ammunition involves the application of fire to targets, general use of weapons by personnel, explosives and propellants, cartridge systems, high explosive projectiles (HE), warheads, shaped charge forms of attack on armor and aircraft, carrier projectiles, fuses, mortar ammunition, small arms ammunition, grenades, mines, pyrotechnics, improved conventional munitions, and terminally guided munition. Also see "Know Your Ammo!" - An Introduction to the Ballistics & Technical Design of Ammunition at https: //www.createspace.com/5804109, & An Introduction to the Ballistics of Firearms at https: //www.createspace.com/5119020 & " A Comprehensive Guide to Handgun Ammunition " at https: //www.createspace.com/6010094
