Download or read book Flexible Joint Robots written by Mark C. Readman and published by CRC Press. This book was released on 1994-07-13 with total page 164 pages. Available in PDF, EPUB and Kindle. Book excerpt: Joint flexibility from harmonic or direct drives or flexible couplings limits the performance of robots. Performance can be improved by taking into account the fast dynamics that are introduced by joint flexibility. High gain acceleration feedback from the link angles simplifies the robot dynamics, but is limited by joint flexibility. One solution is to use joint torque feedback to stabilize the fast dynamics. In light of this, drive systems that incorporate joint torque sensors are being developed. Flexible Joint Robots is the first book to consider the myriad problems and potential solutions that affect flexible joint robot design. The book covers fundamental concepts, including joint torque feedback control laws, acceleration feedback, and adaptive control laws. It presents a dynamic model of a flexible joint robot in several coordinate systems and includes an analysis of the fast dynamics.

Download or read book Control Problems in Robotics written by Antonio Bicchi and published by Springer Science & Business Media. This book was released on 2007-07-12 with total page 283 pages. Available in PDF, EPUB and Kindle. Book excerpt: The ?eld of robotics continues to ?ourish and develop. In common with general scienti?c investigation, new ideas and implementations emerge quite spontaneously and these are discussed, used, discarded or subsumed at c- ferences, in the reference journals, as well as through the Internet. After a little more maturity has been acquired by the new concepts, then archival publication as a scienti?c or engineering monograph may occur. The goal of the Springer Tracts in Advanced Robotics is to publish new developments and advances in the ?elds of robotics research – rapidly and informally but with a high quality. It is hoped that prospective authors will welcome the opportunity to publish a structured presentation of some of the emerging robotics methodologies and technologies. The edited volume by Antonio Bicchi, Henrik Christensen and Domenico Prattichizzo is the outcome of the second edition of a workshop jointly sponsored by the IEEE Control Systems Society and the IEEE Robotics and Automation Society. Noticeably, the previous volume was published in the Springer Lecture Notes on Control and Information Sciences. The authors are recognised as leading scholars internationally. A n- ber of challenging control problems on the forefront of today’s research in robotics and automation are covered, with special emphasis on vision, sensory-feedback control, human-centered robotics, manipulation, planning, ?exible and cooperative robots, assembly systems.

Download or read book Springer Handbook of Robotics written by Bruno Siciliano and published by Springer. This book was released on 2016-07-27 with total page 2259 pages. Available in PDF, EPUB and Kindle. Book excerpt: The second edition of this handbook provides a state-of-the-art overview on the various aspects in the rapidly developing field of robotics. Reaching for the human frontier, robotics is vigorously engaged in the growing challenges of new emerging domains. Interacting, exploring, and working with humans, the new generation of robots will increasingly touch people and their lives. The credible prospect of practical robots among humans is the result of the scientific endeavour of a half a century of robotic developments that established robotics as a modern scientific discipline. The ongoing vibrant expansion and strong growth of the field during the last decade has fueled this second edition of the Springer Handbook of Robotics. The first edition of the handbook soon became a landmark in robotics publishing and won the American Association of Publishers PROSE Award for Excellence in Physical Sciences & Mathematics as well as the organization’s Award for Engineering & Technology. The second edition of the handbook, edited by two internationally renowned scientists with the support of an outstanding team of seven part editors and more than 200 authors, continues to be an authoritative reference for robotics researchers, newcomers to the field, and scholars from related disciplines. The contents have been restructured to achieve four main objectives: the enlargement of foundational topics for robotics, the enlightenment of design of various types of robotic systems, the extension of the treatment on robots moving in the environment, and the enrichment of advanced robotics applications. Further to an extensive update, fifteen new chapters have been introduced on emerging topics, and a new generation of authors have joined the handbook’s team. A novel addition to the second edition is a comprehensive collection of multimedia references to more than 700 videos, which bring valuable insight into the contents. The videos can be viewed directly augmented into the text with a smartphone or tablet using a unique and specially designed app. Springer Handbook of Robotics Multimedia Extension Portal: http://handbookofrobotics.org/

Download or read book Distributed Autonomous Robotic Systems 3 written by Tim Lueth and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Distributed autonomous robotic systems (DARS) are systems composed of multiple autonomous units such as modules, cells, processors, agents, and robots. Combination or cooperative operation of multiple autonomous units is expected to lead to desirable features such as flexibility, fault tolerance, and efficiency. The DARS is the leading established conference on distributed autonomous systems. All papers have the common goal to contribute solutions to the very demanding task of designing distributed systems to realize robust and intelligent robotic systems.

Download or read book Brain Body and Machine written by Jorge Angeles and published by Springer Science & Business Media. This book was released on 2010-10-01 with total page 364 pages. Available in PDF, EPUB and Kindle. Book excerpt: The reader will find here papers on human-robot interaction as well as human safety algorithms; haptic interfaces; innovative instruments and algorithms for the sensing of motion and the identification of brain neoplasms; and, even a paper on a saxophone-playing robot.

Download or read book Springer Handbook of Automation written by Shimon Y. Nof and published by Springer Nature. This book was released on 2023-06-16 with total page 1533 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook incorporates new developments in automation. It also presents a widespread and well-structured conglomeration of new emerging application areas, such as medical systems and health, transportation, security and maintenance, service, construction and retail as well as production or logistics. The handbook is not only an ideal resource for automation experts but also for people new to this expanding field.

Download or read book A Roadmap for Cognitive Development in Humanoid Robots written by David Vernon and published by Springer Science & Business Media. This book was released on 2011-12-28 with total page 233 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book addresses the central role played by development in cognition. The focus is on applying our knowledge of development in natural cognitive systems, specifically human infants, to the problem of creating artificial cognitive systems in the guise of humanoid robots. The approach is founded on the three-fold premise that (a) cognition is the process by which an autonomous self-governing agent acts effectively in the world in which it is embedded, (b) the dual purpose of cognition is to increase the agent's repertoire of effective actions and its power to anticipate the need for future actions and their outcomes, and (c) development plays an essential role in the realization of these cognitive capabilities. Our goal in this book is to identify the key design principles for cognitive development. We do this by bringing together insights from four areas: enactive cognitive science, developmental psychology, neurophysiology, and computational modelling. This results in roadmap comprising a set of forty-three guidelines for the design of a cognitive architecture and its deployment in a humanoid robot. The book includes a case study based on the iCub, an open-systems humanoid robot which has been designed specifically as a common platform for research on embodied cognitive systems .

Download or read book Underactuated Robotic Hands written by Lionel Birglen and published by Springer Science & Business Media. This book was released on 2008-02-11 with total page 248 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a cornerstone publication in robotic grasping. The authors have developed an internationally recognized expertise in this area. Additionally, they designed and built several prototypes which attracted the attention of the scientific community. The purpose of this book is to summarize years of research and to present, in an attractive format, the expertise developed by the authors on a new technology for grasping which has achieved great success both in theory and in practice.

Download or read book Delft Pneumatic Bipeds written by Martjin Wisse and published by Springer Science & Business Media. This book was released on 2007-06-29 with total page 143 pages. Available in PDF, EPUB and Kindle. Book excerpt: In this book, Martijn Wisse and Richard Q. van der Linde provide a detailed description of their research on pneumatic biped robots at the Delft University of Technology, The Netherlands. The book covers the basic theory of passive dynamic walking and explains the implementation of pneumatic McKibben muscles in a series of successful prototypes.

Download or read book Informatics in Control Automation and Robotics written by Juan Andrade Cetto and published by Springer Science & Business Media. This book was released on 2011-03-15 with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present book includes a set of selected papers from the fourth “International Conference on Informatics in Control Automation and Robotics” (ICINCO 2009), held in Milan, Italy, from 2 to 5 July 2009. The conference was organized in three simultaneous tracks: “Intelligent Control Systems and Optimization”, “Robotics and Automation” and “Systems Modeling, Signal Processing and Control”. The book is based on the same structure. ICINCO received 365 paper submissions, not including those of workshops, from 55 countries, in all continents. After a double blind paper review performed by the Program Committee only 34 submissions were accepted as full papers and thus selected for oral presentation, leading to a full paper acceptance ratio of 9%. Additional papers were accepted as short papers and posters. A further refinement was made after the conference, based also on the assessment of presentation quality, so that this book includes the extended and revised versions of the very best papers of ICINCO 2009. Commitment to high quality standards is a major concern of ICINCO that will be maintained in the next editions of this conference, including not only the stringent paper acceptance ratios but also the quality of the program committee, keynote lectures, workshops and logistics.

Download or read book Autonomous Flying Robots written by Kenzo Nonami and published by Springer Science & Business Media. This book was released on 2010-09-15 with total page 341 pages. Available in PDF, EPUB and Kindle. Book excerpt: The advance in robotics has boosted the application of autonomous vehicles to perform tedious and risky tasks or to be cost-effective substitutes for their - man counterparts. Based on their working environment, a rough classi cation of the autonomous vehicles would include unmanned aerial vehicles (UAVs), - manned ground vehicles (UGVs), autonomous underwater vehicles (AUVs), and autonomous surface vehicles (ASVs). UAVs, UGVs, AUVs, and ASVs are called UVs (unmanned vehicles) nowadays. In recent decades, the development of - manned autonomous vehicles have been of great interest, and different kinds of autonomous vehicles have been studied and developed all over the world. In part- ular, UAVs have many applications in emergency situations; humans often cannot come close to a dangerous natural disaster such as an earthquake, a ood, an active volcano, or a nuclear disaster. Since the development of the rst UAVs, research efforts have been focused on military applications. Recently, however, demand has arisen for UAVs such as aero-robotsand ying robotsthat can be used in emergency situations and in industrial applications. Among the wide variety of UAVs that have been developed, small-scale HUAVs (helicopter-based UAVs) have the ability to take off and land vertically as well as the ability to cruise in ight, but their most importantcapability is hovering. Hoveringat a point enables us to make more eff- tive observations of a target. Furthermore, small-scale HUAVs offer the advantages of low cost and easy operation.

Download or read book Identification of Dynamic Systems written by Rolf Isermann and published by Springer. This book was released on 2011-04-08 with total page 705 pages. Available in PDF, EPUB and Kindle. Book excerpt: Precise dynamic models of processes are required for many applications, ranging from control engineering to the natural sciences and economics. Frequently, such precise models cannot be derived using theoretical considerations alone. Therefore, they must be determined experimentally. This book treats the determination of dynamic models based on measurements taken at the process, which is known as system identification or process identification. Both offline and online methods are presented, i.e. methods that post-process the measured data as well as methods that provide models during the measurement. The book is theory-oriented and application-oriented and most methods covered have been used successfully in practical applications for many different processes. Illustrative examples in this book with real measured data range from hydraulic and electric actuators up to combustion engines. Real experimental data is also provided on the Springer webpage, allowing readers to gather their first experience with the methods presented in this book. Among others, the book covers the following subjects: determination of the non-parametric frequency response, (fast) Fourier transform, correlation analysis, parameter estimation with a focus on the method of Least Squares and modifications, identification of time-variant processes, identification in closed-loop, identification of continuous time processes, and subspace methods. Some methods for nonlinear system identification are also considered, such as the Extended Kalman filter and neural networks. The different methods are compared by using a real three-mass oscillator process, a model of a drive train. For many identification methods, hints for the practical implementation and application are provided. The book is intended to meet the needs of students and practicing engineers working in research and development, design and manufacturing.

Download or read book Autonomous Robotic Systems written by Changjiu Zhou and published by Physica. This book was released on 2013-03-20 with total page 505 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book contains an edited collection of eighteen contributions on soft and hard computing techniques and their applications to autonomous robotic systems. Each contribution has been exclusively written for this volume by a leading researcher. The volume demonstrates the various ways that the soft computing and hard computing techniques can be used in different integrated manners to better develop autonomous robotic systems that can perform various tasks of vision, perception, cognition, thinking, pattern recognition, decision-making, and reasoning and control, amongst others. Each chapter of the book is self-contained and points out the future direction of research. "It is a must reading for students and researchers interested in exploring the potentials of the fascinating field that will form the basis for the design of the intelligent machines of the future" (Madan M. Gupta)

Download or read book Product Design and Development written by Karl T. Ulrich and published by Irwin/McGraw-Hill. This book was released on 2004 with total page 392 pages. Available in PDF, EPUB and Kindle. Book excerpt: This text presents a set of product development techniques aimed at bringing together the marketing, design, and manufacturing functions of the enterprise. The integrative methods facilitate problem-solving and decision-making.

Download or read book Enabling Manufacturing Competitiveness and Economic Sustainability written by Hoda A. ElMaraghy and published by Springer Science & Business Media. This book was released on 2011-09-29 with total page 674 pages. Available in PDF, EPUB and Kindle. Book excerpt: The changing manufacturing environment requires more responsive and adaptable manufacturing systems. The theme of the 4th International Conference on Changeable, Agile, Reconfigurable and Virtual production (CARV2011) is “Enabling Manufacturing Competitiveness and Economic Sustainability”. Leading edge research and best implementation practices and experiences, which address these important issues and challenges, are presented. The proceedings include advances in manufacturing systems design, planning, evaluation, control and evolving paradigms such as mass customization, personalization, changeability, re-configurability and flexibility. New and important concepts such as the dynamic product families and platforms, co-evolution of products and systems, and methods for enhancing manufacturing systems’ economic sustainability and prolonging their life to produce more than one product generation are treated. Enablers of change in manufacturing systems, production volume and capability scalability and managing the volatility of markets, competition among global enterprises and the increasing complexity of products, manufacturing systems and management strategies are discussed. Industry challenges and future directions for research and development needed to help both practitioners and academicians are presented.

Download or read book Innovations in Robot Mobility and Control written by Srikanta Patnaik and published by Springer. This book was released on 2006-04-20 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: There exists quite a vast literature on mobile robots, covering fundamental principles on motion control and path-planning in indoor environments using ultrasonic/laser transducers. However, there is a scarcity of books/collective documents on vision based navigation of mobile robots and multi-agent systems. The book Innovations in Robot Mobility and Control fills this gap. It attempts to develop interesting models for vision based map building in indoor and outdoor environments, precise motion control, navigation in dynamic environment, and above all multi-agent co-operation of robots. The most important aspects of this book is that the principles and models introduced in the text are all field-tested, and thus can readily be used in solving real world problems, such as factory automation, disposal of nuclear wastes, landmine clearing and computerized surgery. The chapters presented in the book have been contributed by specialist researchers from different disciplines of robotics. The book thus is unique in its contents and originality. Though contributed by several researchers, the presentation style of the book is uniform throughout. Primarily meant for graduate students and researchers in robotics, the book is equally useful to interested audience of any discipline for its contents and simplicity in presentation style.

Download or read book Transforming Automobile Assembly written by Koichi Shimokawa and published by Springer Science & Business Media. This book was released on 2012-12-06 with total page 421 pages. Available in PDF, EPUB and Kindle. Book excerpt: For the world's leading car-makers, the early 1990s brought radical changes. The reports published by MIT shocked management in European and American industries. Former major companies had to face consequences no one had expected. The assembly-lines were reorganized in order to achieve higher quality at lower costs. Five years after the MIT report, this book poses the question: What are the results of this revolution in work organization? Scientists and practitioners, many of them involved in earlier reports, evaluate the changes to the automotive industry in Europe and Japan. An insight into recent concepts in automation and the organization of production.