Download or read book A Study of Computer Simulation in D I Diesel Engine Performance and Emission Prediction written by Li-zhong Quan and published by . This book was released on 1994 with total page 386 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Engine Modeling and Simulation written by Avinash Kumar Agarwal and published by Springer Nature. This book was released on 2021-12-16 with total page 368 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book focuses on the simulation and modeling of internal combustion engines. The contents include various aspects of diesel and gasoline engine modeling and simulation such as spray, combustion, ignition, in-cylinder phenomena, emissions, exhaust heat recovery. It also explored engine models and analysis of cylinder bore piston stresses and temperature effects. This book includes recent literature and focuses on current modeling and simulation trends for internal combustion engines. Readers will gain knowledge about engine process simulation and modeling, helpful for the development of efficient and emission-free engines. A few chapters highlight the review of state-of-the-art models for spray, combustion, and emissions, focusing on the theory, models, and their applications from an engine point of view. This volume would be of interest to professionals, post-graduate students involved in alternative fuels, IC engines, engine modeling and simulation, and environmental research.
Download or read book Modelling Diesel Combustion written by P. A. Lakshminarayanan and published by Springer Science & Business Media. This book was released on 2010-03-03 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: Phenomenology of Diesel Combustion and Modeling Diesel is the most efficient combustion engine today and it plays an important role in transport of goods and passengers on land and on high seas. The emissions must be controlled as stipulated by the society without sacrificing the legendary fuel economy of the diesel engines. These important drivers caused innovations in diesel engineering like re-entrant combustion chambers in the piston, lower swirl support and high pressure injection, in turn reducing the ignition delay and hence the nitric oxides. The limits on emissions are being continually reduced. The- fore, the required accuracy of the models to predict the emissions and efficiency of the engines is high. The phenomenological combustion models based on physical and chemical description of the processes in the engine are practical to describe diesel engine combustion and to carry out parametric studies. This is because the injection process, which can be relatively well predicted, has the dominant effect on mixture formation and subsequent course of combustion. The need for improving these models by incorporating new developments in engine designs is explained in Chapter 2. With “model based control programs” used in the Electronic Control Units of the engines, phenomenological models are assuming more importance now because the detailed CFD based models are too slow to be handled by the Electronic Control Units. Experimental work is necessary to develop the basic understanding of the pr- esses.
Download or read book Simulation Studies of Diesel Engine Performance with Oxygen Enriched Air and Water Emulsified Fuels written by and published by . This book was released on 1990 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: A computer simulation code of a turbocharged, turbocompound diesel engine was modified to study the effects of using oxygen-enriched combustion air and water-emulsified diesel fuels. Oxygen levels of 21 percent to 40 percent by volume in the combustion air were studied. Water content in the fuel was varied from 0 percent to 50 percent mass. Simulation studies and a review and analysis of previous work in this area led to the following conclusions about expected engine performance and emissions: the power density of the engine is significantly increased by oxygen enrichment. Ignition delay and particulate emissions are reduced. Combustion temperatures and No(subscript x) emissions are increased with oxygen enrichment but could be brought back to the base levels by introducing water in the fuel. The peak cylinder pressure which increases with the power output level might result in mechanical problems with engine components. Oxygen enrichment also provides an opportunity to use cheaper fuel such as No. 6 diesel fuel. Overall, the adverse effects of oxygen enrichment could be countered by the addition of water and it appears that an optimum combination of water content, oxygen level, and base diesel fuel quality may exist. This could yield improved performance and emissions characteristics compared to a state-of-the-art diesel engine. 9 refs., 8 figs.
Download or read book Computer Simulation of the Turbocharged Turbocompounded Diesel Engine System for Studies of Low Heat Rejection Engine Performance written by Dennis N. Assanis and published by . This book was released on 1985 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Computer Simulation of the Turbocharged Turbocompounded Diesel Engine System for Studies of Low Heat Rejection Engine Performance written by Dionissios Nikolaou Assanis and published by . This book was released on 1985 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Studies of Diesel Engine Combustion Using a Multidimensional Computer Simulation written by Constantine A. Varnavas and published by . This book was released on 1990 with total page 192 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Performance Investigations on a Computer Simulated Four Stroke Diesel Engine written by Harold George Weber and published by . This book was released on 1967 with total page 234 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A Quasi dimensional Charge Motion and Turbulence Model for Combustion and Emissions Prediction in Diesel Engines with a fully Variable Valve Train written by Qirui Yang and published by Springer Nature. This book was released on 2021-10-01 with total page 141 pages. Available in PDF, EPUB and Kindle. Book excerpt: Qirui Yang develops a model chain for the simulation of combustion and emissions of diesel engine with fully variable valve train (VVT) based on extensive 3D-CFD simulations, and experimental measurements on the engine test bench. The focus of the work is the development of a quasi-dimensional (QDM) flow model, which sets up a series of sub-models to describe phenomenologically the swirl, squish and axial charge motions as well as the shear-related turbulence production and dissipation. The QDM flow model is coupled with a QDM combustion model and a nitrogen oxides (NOx) / soot emission model. With the established model chain, VVT operating strategies of diesel engine can be developed and optimized as part of the simulation for specific engine performance parameters and the lowest NOx and soot emissions.
Download or read book Three Dimensional Modeling of Diesel Engine Intake Flow Combustion and Emissions 2 written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-17 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: A three-dimensional computer code, KIVA, is being modified to include state-of-the-art submodels for diesel engine flow and combustion. Improved and/or new submodels which have already been implemented and previously reported are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NO(x), and spray/wall impingement with rebounding and sliding drops. Progress on the implementation of improved spray drop drag and drop breakup models, the formulation and testing of a multistep kinetics ignition model, and preliminary soot modeling results are described. In addition, the use of a block structured version of KIVA to model the intake flow process is described. A grid generation scheme was developed for modeling realistic (complex) engine geometries, and computations were made of intake flow in the ports and combustion chamber of a two-intake-value engine. The research also involves the use of the code to assess the effects of subprocesses on diesel engine performance. The accuracy of the predictions is being tested by comparisons with engine experiments. To date, comparisons were made with measured engine cylinder pressure, temperature and heat flux data, and the model results are in good agreement with the experiments. Work is in progress that will allow validation of in-cylinder flow and soot formation predictions. An engine test facility is described that is being used to provide the needed validation data. Test results were obtained showing the effect of injection rate and split injections on engine performance and emissions. Reitz, R. D. and Rutland, C. J. Unspecified Center...
Download or read book Modeling Engine Spray and Combustion Processes written by Gunnar Stiesch and published by Springer Science & Business Media. This book was released on 2003-04-10 with total page 314 pages. Available in PDF, EPUB and Kindle. Book excerpt: The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Download or read book A Computer Simulation of the Turbocharged DI Diesel Engine as an Enchancement of the Vehicle Engine Cooling System Simulation written by Krishna V. Mohan and published by . This book was released on 1997 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Proceedings of the FISITA 2012 World Automotive Congress written by SAE-China and published by Springer Science & Business Media. This book was released on 2012-11-02 with total page 558 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of the FISITA 2012 World Automotive Congress are selected from nearly 2,000 papers submitted to the 34th FISITA World Automotive Congress, which is held by Society of Automotive Engineers of China (SAE-China ) and the International Federation of Automotive Engineering Societies (FISITA). This proceedings focus on solutions for sustainable mobility in all areas of passenger car, truck and bus transportation. Volume 2: Advanced Internal Combustion Engines (II) focuses on: •Flow and Combustion Diagnosis •Engine Design and Simulation •Heat Transfer and Waste Heat Reutilization •Emission Standard and International Regulations Above all researchers, professional engineers and graduates in fields of automotive engineering, mechanical engineering and electronic engineering will benefit from this book. SAE-China is a national academic organization composed of enterprises and professionals who focus on research, design and education in the fields of automotive and related industries. FISITA is the umbrella organization for the national automotive societies in 37 countries around the world. It was founded in Paris in 1948 with the purpose of bringing engineers from around the world together in a spirit of cooperation to share ideas and advance the technological development of the automobile.
Download or read book Simulation of the Diesel Engine Combustion Process Using the Stochastic Reactor Model written by Michal Pasternak and published by Logos Verlag Berlin. This book was released on 2016 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: The present work is concerned with the simulation of combustion, emission formation and fuel effects in Diesel engines. The simulation process is built around a zero-dimensional (0D) direct injection stochastic reactor model (DI-SRM), which is based on a probability density function (PDF) approach. An emphasis is put on the modelling of mixing time to improve the representation of turbulence-chemistry interactions in the 0D DI-SRM. The mixing time model describes the intensity of mixing in the gas-phase for scalars such as enthalpy and species mass fraction. On a crank angle basis, it governs the composition of the gas mixture that is described by PDF distributions for the scalars. The derivation of the mixing time is based on an extended heat release analysis that has been fully automated using a genetic algorithm. The predictive nature of simulations is achieved through the parametrisation of the mixing time model with known engine operating parameters such as speed, load and fuel injection strategy. It is shown that crank angle dependency of the mixing time improves the modelling of local inhomogeneity in the gas-phase for species mass fraction and temperature. In combination with an exact treatment of the non-linearity of reaction kinetics, it enables an accurate prediction of the rate of heat release, in-cylinder pressure and exhaust emissions, such as nitrogen oxides, unburned hydrocarbons and soot, from differently composed fuels. The method developed is particularly tailored for computationally efficient applications that focus on the details of reaction kinetics and the locality of combustion and emission formation in Diesel engines.
Download or read book Transport Phenomena In Combustion written by SH Chan and published by Taylor & Francis. This book was released on 2024-09-06 with total page 1862 pages. Available in PDF, EPUB and Kindle. Book excerpt: This two-volume set presents the proceedings from the 8th International Symposium on Transport Phenomena in Combustion. There are more than 150 chapters that provide an extensive review of topics such as complete numerical simulation of combustion and heat transfer in furnaces and boilers, the interaction of combustion and heat transfer in porous media for low emission, high efficiency applications, industrial combustion technology, experimental and diagnostic methods and active combustion control, and fire research, internal combustion engine, Nox and soot emission.
Download or read book Diesel Engine Modeling written by Society of Automotive Engineers and published by SAE International. This book was released on 1999 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Diesel Engine Transient Operation written by Constantine D. Rakopoulos and published by Springer Science & Business Media. This book was released on 2009-03-10 with total page 408 pages. Available in PDF, EPUB and Kindle. Book excerpt: Traditionally, the study of internal combustion engines operation has focused on the steady-state performance. However, the daily driving schedule of automotive and truck engines is inherently related to unsteady conditions. In fact, only a very small portion of a vehicle’s operating pattern is true steady-state, e. g. , when cruising on a motorway. Moreover, the most critical conditions encountered by industrial or marine engines are met during transients too. Unfortunately, the transient operation of turbocharged diesel engines has been associated with slow acceleration rate, hence poor driveability, and overshoot in particulate, gaseous and noise emissions. Despite the relatively large number of published papers, this very important subject has been treated in the past scarcely and only segmentally as regards reference books. Merely two chapters, one in the book Turbocharging the Internal Combustion Engine by N. Watson and M. S. Janota (McMillan Press, 1982) and another one written by D. E. Winterbone in the book The Thermodynamics and Gas Dynamics of Internal Combustion Engines, Vol. II edited by J. H. Horlock and D. E. Winterbone (Clarendon Press, 1986) are dedicated to transient operation. Both books, now out of print, were published a long time ago. Then, it seems reasonable to try to expand on these pioneering works, taking into account the recent technological advances and particularly the global concern about environmental pollution, which has intensified the research on transient (diesel) engine operation, typically through the Transient Cycles certification of new vehicles.
