Download or read book X Band Klystron Development at the Stanford Linear Accelerator Center written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: X-band klystrons capable of 75 MW and utilizing either solenoidal or Periodic Permanent Magnet (PPM) focusing are undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC). The klystron development is part of an effort to realize components necessary for the construction of the Next Linear Collider (NLC). SLAC has completed a solenoidal-focused X-band klystron development effort to study the design and operation of tubes with beam microperveances of 1.2. As of early 2000, nine 1.2[micro]K klystrons have been tested to 50 MW at 1.5[micro]s. The first 50 MW PPM klystron, constructed in 1996, was designed with a 0.6[micro]K beam at 465 kV and uses a 5-cell traveling-wave output structure. Recent testing of this tube at wider pulsewidths has reached 50 MW at 55% efficiency, 2.4[micro]s and 60 Hz. A 75 MW PPM klystron prototype was constructed in 1998 and has reached the NLC design target of 75 MW at 1.5[micro]s. A new 75 MW PPM klystron design, which is aimed at reducing the cost and increasing the reliability of multi-megawatt PPM klystrons, is under investigation. The tube is scheduled for testing during early 2001.
Download or read book PPM Focused X band Klystron Development at the Stanford Linear Accelerator Center written by and published by . This book was released on 1996 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: X-band klystrons capable of 50 MW and utilizing Periodic Permanent Magnet (PPM) focusing are undergoing design and fabrication at the Stanford Linear Accelerator Center (SLAC). The klystron development is part of an effort to realize components necessary for the construction of the Next Linear Collider (NLC). The first klystron to be tested this year has a 0.6 microK beam at 465 kV, a 5 cells traveling wave output structure and a predicted efficiency of 63%. A 465 kV, 190 A beam stick with 12 periods of PPM focusing has recently operated to verify the gun optics and transmission of the beam in the absence of rf bunching. Beam transmission greater than 99.8% has been measured. Design and simulation of the beam stick and klystron are discussed, along with performance of the beam stick under confined flow and shielded conditions.
Download or read book SLAC RF Source Research at X Band written by and published by . This book was released on 2003 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: X-band klystrons capable of 75 MW and utilizing either solenoidal or Periodic Permanent Magnet (PPM) focusing are undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC). The klystron development is part of an effort to realize components necessary for the construction of the Next Linear Collider (NLC). SLAC has developed a solenoidal-focused X-band klystron which is currently the workhorse of high power component testing for the NLC. A state-of-the-art modulator will drive eight of these tubes which, in turn, will power an rf distribution system referred to as the ''8-pack'' in order to test these modulators and waveguide components. Eventually, in an interest to save millions of dollars per year in the operational cost of the NLC, these tubes will be replaced by PPM klystrons. The PPM devices built to date which fit this class of operation consist of a variety of 50 MW and 75 MW devices constructed by SLAC, KEK (Tsukuba, Japan), and industry. These tubes follow from the successful 50 MW PPM design of 1996. Recent testing of this particular tube at wider pulsewidths has reached 50 MW at 55% efficiency, 2.4[micro]s and 60 Hz. Two 50 MW PPM klystrons produced by industry have been delivered to SLAC. One of these devices arrived with a vacuum suitable for test. Testing during 2001 revealed a serious, but curious, vacuum response which limited the operation to an rf output of[approx]40 MW. A 75 MW PPM klystron prototype was first constructed in 1997 and later modified in 1999 to eliminate oscillations. This tube has reached the NLC design target of 75 MW at 1.5[micro]s though at a significantly reduced rep rate. Two new 75 MW PPM klystrons were constructed and tested in 2002 after a diode was successfully tested in 2001. The new design was aimed at reducing the cost and increasing the reliability of such high-energy devices. The rf circuit and beam focusing for one of these devices was built by industry and incorporated into one of the tubes. Both of these latest devices suffered from a variety of issues concerning gun stability, beam confinement and rf stability. A rebuilt version of this latest design was constructed in early 2003 and completed testing in June. The performance of these various klystrons, particularly during 2002 and 2003, will be presented along with results of studies pertinent to their construction. Design and manufacturing issues of the various klystrons are discussed, along with plans for future modifications and areas of research.
Download or read book Periodic Permanent Magnet Development for Linear Collider X band Klystrons written by and published by . This book was released on 2003 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The Stanford Linear Accelerator Center (SLAC) klystron group is currently designing, fabricating and testing 11.424 GHz klystrons with peak output powers from 50 to 75 MW at 1 to 2[micro]s rf pulsewidths as part of an effort to realize components necessary for the construction of the Next Linear Collider (NLC). In order to eliminate the projected operational-year energy bill for klystron solenoids, Periodic Permanent Magnet (PPM) focusing has been employed on the latest X-band klystron designs. A PPM beam tester has operated at the same repetition rate, voltage and average beam power required for a 75 MW NLC klystron. Prototype 50 and 75 MW PPM klystrons were built and tested during 1996 and 1997 which operate from 50 to 70 MW at efficiencies greater than 55%. Construction and testing of 75 MW research klystrons will continue while the design and reliability is perfected. This paper discusses the design of these PPM klystrons and the results of testing to date along with future plans for the development of a low-cost Design for Manufacture (DFM) 75 MW klystron and invitation for industry participation.
Download or read book High Power Microwaves written by James Benford and published by CRC Press. This book was released on 2015-11-04 with total page 466 pages. Available in PDF, EPUB and Kindle. Book excerpt: Following in the footsteps of its popular predecessors, High Power Microwaves, Third Edition continues to provide a wide-angle, integrated view of the field of high power microwaves (HPMs). This third edition includes significant updates in every chapter as well as a new chapter on beamless systems that covers nonlinear transmission lines.Written b
Download or read book High Energy Density and High Power RF written by David K. Abe and published by Springer Science & Business Media. This book was released on 2006-01-04 with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the seventh in a series of international workshops on high-power and high-energy density microwave devices for accelerator, plasma physics, and defense applications. The scope of this workshop included accelerators for high energy physics, plasma heating and current drive in controlled thermonuclear fusion research, radar and directed energy/high power microwave systems, THz sources and technologies, and advanced 2D/3D computational tool development.
Download or read book Design Optimization and Construction of the Thyratron written by and published by . This book was released on 1999 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: As design studies and various R and D efforts continue on Next Linear Collider (NLC) systems, much R and D work is being done on X-Band klystron development, and development of pulse modulators to drive these X-Band klystrons. A workshop on this subject was held at SLAC in June of 1998, and a follow-up workshop is scheduled at SLAC June 23-25, 1999. At the 1998 workshop, several avenues of R and D were proposed using solid state switching, induction LINAC principles, high voltage hard tubes, and a few more esoteric ideas. An optimized version of the conventional thyratron-PFN-pulse transformer modulator for which there is extensive operating experience is also a strong candidate for use in the NLC. Such a modulator is currently under construction for base line demonstration purposes. The performance of this ''Cost Model'' modulator will be compared to other developing technologies. Important parameters including initial capital cost, operating maintenance cost, reliability, maintainability, power efficiency, in addition to the usual operating parameters of pulse flatness, timing and pulse height jitter, etc. will be considered in the choice of a modulator design for the NLC. This paper updates the progress on this ''Cost Model'' modulator design and construction.
Download or read book Femtosecond Laser Clocked Compact X band High Gradient Photoinjector and Accelerator for Compton Scattering written by Christopher A. DeStefano and published by . This book was released on 2008 with total page 530 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Latest Results in SLAC 75 MW PPM Klystrons written by R. Phillips and published by . This book was released on 2006 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt: 75 MW X-band klystrons utilizing Periodic Permanent Magnet (PPM) focusing have been undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC) for almost nine years. The klystron development has been geared toward realizing the necessary components for the construction of the Next Linear Collider (NLC). The PPM devices built to date which fit this class of operation consist of a variety of 50 MW and 75 MW devices constructed by SLAC, KEK (Tsukuba, Japan) and industry. All these tubes follow from the successful SLAC design of a 50 MW PPM klystron in 1996. In 2004 the latest two klystrons were constructed and tested with preliminary results reported at EPAC2004. The first of these two devices was tested to the full NLC specifications of 75 MW, 1.6 microseconds pulse length, and 120 Hz. This 14.4 kW average power operation came with a tube efficiency>50%. The most recent testing of these last two devices will be presented here. Design and manufacturing issues of the latest klystron, due to be tested by the Fall of 2005, are also discussed.
Download or read book Generation and Application of High Power Microwaves written by R.A Cairns and published by CRC Press. This book was released on 2020-08-18 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written at the graduate level, Generation and Application of High Power Microwaves discusses the basic physics of the generation of microwave and radiofrequency waves in the megawatt power range and the application of these ideas to a range of devices such as klystrons, gyrotrons, and free electron lasers. The book also contains chapters covering the transmission of the power through waveguides and the problems associated with mode conversion in transmission lines. The main application area covered is the heating and current drive in tokamaks and other devices for research into controlled nuclear fusion. Other applications of high power microwave technology are not neglected, and among those discussed are multiple charged ion and soft x-ray sources, electron spin resonance spectroscopy, advanced materials processing, millimeter wave radar, and supercolliders.
Download or read book Energy Research Abstracts written by and published by . This book was released on 1994 with total page 444 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Klystrons Traveling Wave Tubes Magnetrons Crossed field Amplifiers and Gyrotrons written by A.S. Gilmour Jr. and published by Artech House. This book was released on 2011 with total page 883 pages. Available in PDF, EPUB and Kindle. Book excerpt: Microwave tubes are vacuum electron devices used for the generation and amplification of radio frequencies in the microwave range. An established technology area, the use of tubes remains essential in the field today for high-power applications. The culmination of the authorOCOs 50 years of industry experience, this authoritative resource offers you a thorough understanding of the operations and major classes of microwave tubes.Minimizing the use of advanced mathematics, the book places emphasis on clear qualitative explanations of phenomena. This practical reference serves as an excellent introduction for newcomers to the field and offers established tube engineers a comprehensive refresher. Professionals find coverage of all major tube classifications, including klystrons, traveling wave tubes (TWTs), magnetrons, cross field amplifiers, and gyrotrons."
Download or read book Microwave and Millimeter Wave Vacuum Electron Devices Inductive Output Tubes Klystrons Traveling Wave Tubes Magnetrons Crossed Field Amplifiers and Gyrotrons written by A.S. Gilmour, Jr. and published by Artech House. This book was released on 2020-04-30 with total page 880 pages. Available in PDF, EPUB and Kindle. Book excerpt: Written by an internationally recognized as an expert on the subject of microwave (MW) tubes, this book presents and describes the many types of microwave tubes, and despite competition from solid-state devices (those using GaN, SiC, et cetera), which continue to be used widely and find new applications in defense, communications, medical, and industrial drying. Helix traveling wave tubes (TWTs), as well as coupled cavity TWTs are covered. Klystrons, and how they work, are described, along with the physics behind it and examples of devices and their uses. Vacuum electron devices are explained in detail and examines the harsh environment that must exist in tubes if they are to operate properly. The secondary emission process and its role in the operation of crossed-field devices is also discussed. The design of collectors for linear-beam tubes, including power dissipation and power recovery, are explored. Discussions of important noise sources and techniques that can be used to minimize their effects are also included. Presented in full color, this book contains a balance of practical and theoretical material so that those new to microwave tubes as well as experienced microwave tube technicians, engineers, and managers can benefit from its use.
Download or read book Beam Line written by and published by . This book was released on 1990 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ERDA Energy Research Abstracts written by and published by . This book was released on 1983 with total page 1028 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book European Particle Accelerator Conference Epac 94 In 3 Volumes written by Christine Petit-jean-genaz and published by World Scientific. This book was released on 1994-11-26 with total page 2968 pages. Available in PDF, EPUB and Kindle. Book excerpt: These proceedings aim to provide a comprehensive overview of research, technology and applications in the field of accelerators. Contributions from the entire field of accelerators are presented, including low and high energy machines, and medical and industrial accelerators.
Download or read book High Energy Density and High Power RF written by Steven H. Gold and published by American Institute of Physics. This book was released on 2003-12-04 with total page 460 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is the sixth in a series of international workshops on high-power and high-energy density microwave devices for accelerator, plasma physics, and defense applications. Past workshops were held in Dubna, Montauk, Hayama, Pajaro Dunes, and Snowbird. The theme is research and development of techniques to increase microwave energy density and peak power in active and passive microwave devices and components ranging from L-band to W-band. The scope of this workshop has now been broadened to include radar and high power microwave (HPM) systems, space exploration, neutron sources, and even plasma heating and current drive in controlled thermonuclear fusion research.
