Download or read book Understanding Porosity Formation and Prevention when Welding Titanium Alloys with 1 mu m Wavelength Laser Beams written by Jonathan Edward Blackburn and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Keyhole laser welding is a joining technology characterised by the high focussed power density applied to the workpiece, facilitating deep penetration at high processing speeds. High aspect-ratio welds produced using this process invariably have narrow heat-affected-zones and minimal thermal distortion compared with traditional arc welding processes. Furthermore, the ability to process out of vacuum and the easy robotic manipulation of fibre optically delivered 1[mu]m wavelength laser beams, allow keyhole laser welding to process geometrically complex components. The widespread uptake of keyhole laser welding for the production of titanium alloy components in the aerospace industry has been limited by the stringent weld quality requirements. Producing welds with levels of subsurface weld metal porosity content meeting the required weld quality criteria has been the primary obstacle. Here, three techniques for controlling the levels of weld metal porosity when welding titanium alloys with Nd:YAG rod lasers have been developed. Characterisation of the welding processes using high speed photography and optical spectroscopy, have allowed an original scientific understanding of the effects these methods have on the keyhole, melt pool and vapour plume behaviour. Combining this with a thorough assessment of the weld qualities produced, has enabled the effects of these process behaviours on the formation of weld metal porosity to be determined. It was found that with the correct process parameters a directed gas jet and a dual focus laser welding condition can both be used to reduce the occurrence of keyhole collapse during Nd:YAG laser welding. The directed gas jet prevents the formation of a beam attenuating vapour plume and interacts with the molten metal to produce a stable welding condition, whereas the dual focus laser welding condition reduces fluctuations in the process due to an enlarged keyhole. When applied, both techniques reduced the occurrence of porosity in the weld metal of full penetration butt welds produced in titanium alloys. A modulated Nd:YAG laser output, with the correct waveform and modulation frequency, also reduced the occurrence of porosity in the weld metal compared with welds produced with a continuous-wave output. This was a result of an oscillating wave being set-up in the melt pool which manipulated the keyhole geometry and prevented instabilities in the process being established. In addition, the potential for welding titanium alloys to the required weld quality criteria with state-of-the-art Yb-fibre lasers has been assessed. It was found that the high power densities of suitably focussed laser beams with excellent beam quality, were capable of producing low-porosity full penetration butt welds in titanium alloys without the techniques required for laser beams with a lower beam quality. These new techniques for keyhole laser welding of titanium alloys will encourage the uptake of keyhole laser welding for producing near-net-shape high-performance aerospace components. The advantages offered by this joining technology include high productivity, low heat input and easy robotic automation.
Download or read book Understanding porosity formation and prevention when welding titanium alloys with 1 m wavelength laser beams written by Jonathan Edward Blackburn and published by . This book was released on 2011 with total page 224 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Understanding Porosity Formation and Prevention when Welding Titanium Alloys with 1 m Wavelength Laser Beams written by Jonathan Edward Blackburn and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Handbook of Laser Welding Technologies written by S Katayama and published by Elsevier. This book was released on 2013-06-30 with total page 685 pages. Available in PDF, EPUB and Kindle. Book excerpt: Laser welding is a rapidly developing and versatile technology which has found increasing applications in industry and manufacturing. It allows the precision welding of small and hard-to-reach areas, and is particularly suitable for operation under computer or robotic control. The Handbook of laser welding technologies reviews the latest developments in the field and how they can be used across a variety of applications. Part one provides an introduction to the fundamentals of laser welding before moving on to explore developments in established technologies including CO2 laser welding, disk laser welding and laser micro welding technology. Part two highlights laser welding technologies for various materials including aluminium and titanium alloys, plastics and glass. Part three focuses on developments in emerging laser welding technologies with chapters on the applications of robotics in laser welding and developments in the modelling and simulation of laser and hybrid laser welding. Finally, part four explores the applications of laser welding in the automotive, railway and shipbuilding industries. The Handbook of laser welding technologies is a technical resource for researchers and engineers using laser welding technologies, professionals requiring an understanding of laser welding techniques and academics interested in the field. Provides an introduction to the fundamentals of laser welding including characteristics, welding defects and evolution of laser welding Discusses developments in a number of techniques including disk, conduction and laser micro welding Focusses on technologies for particular materials such as light metal alloys, plastics and glass
Download or read book Hybrid Laser Arc Welding written by F O Olsen and published by Elsevier. This book was released on 2009-06-26 with total page 336 pages. Available in PDF, EPUB and Kindle. Book excerpt: Hybrid laser-arc welding (HLAW) is a combination of laser welding with arc welding that overcomes many of the shortfalls of both processes. This important book gives a comprehensive account of hybrid laser-arc welding technology and applications. The first part of the book reviews the characteristics of the process, including the properties of joints produced by hybrid laser-arc welding and ways of assessing weld quality. Part two discusses applications of the process to such metals as magnesium alloys, aluminium and steel as well as the use of hybrid laser-arc welding in such sectors as ship building and the automotive industry. With its distinguished editor and international team of contributors, Hybrid laser-arc welding is a valuable source of reference for all those using this important welding technology. Reviews arc and laser welding including both advantages and disadvantages of the hybrid laser-arc approach Explores the characteristics of the process including the properties of joints produced by hybrid laser-arc welding and ways of assessing weld quality Examines applications of the process including magnesium alloys, aluminium and steel with specific focus on applications in the shipbuilding and automotive industries
Download or read book Titanium Powder Metallurgy written by Ma Qian and published by Butterworth-Heinemann. This book was released on 2015-02-10 with total page 649 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium Powder Metallurgy contains the most comprehensive and authoritative information for, and understanding of, all key issues of titanium powder metallurgy (Ti PM). It summarizes the past, reviews the present and discusses the future of the science and technology of Ti PM while providing the world titanium community with a unique and comprehensive book covering all important aspects of titanium powder metallurgy, including powder production, powder processing, green shape formation, consolidation, property evaluation, current industrial applications and future developments. It documents the fundamental understanding and technological developments achieved since 1937 and demonstrates why powder metallurgy now offers a cost-effective approach to the near net or net shape fabrication of titanium, titanium alloys and titanium metal matrix composites for a wide variety of industrial applications. Provides a comprehensive and in-depth treatment of the science, technology and industrial practice of titanium powder metallurgy Each chapter is delivered by the most knowledgeable expert on the topic, half from industry and half from academia, including several pioneers in the field, representing our current knowledge base of Ti PM. Includes a critical review of the current key fundamental and technical issues of Ti PM. Fills a critical knowledge gap in powder metal science and engineering and in the manufacture of titanium metal and alloys
Download or read book Laser Material Processing written by William M. Steen and published by Springer Science & Business Media. This book was released on 2013-04-18 with total page 416 pages. Available in PDF, EPUB and Kindle. Book excerpt: New chapters on bending and cleaning reflect the changes in the field since the last edition, completing the range of practical knowledge about the processes possible with lasers already familiar to users of this well-known text. Professor Steen's lively presentation is supported by a number of original cartoons by Patrick Wright and Noel Ford, which will bring a smile to your face and ease the learning process. From the reviews: "...well organized, and the text is very practical...The engineering community will find this book informative and useful." (OPTICS AND PHOTONICS NEWS, July/August 2005)
Download or read book Al Si Alloys written by Francisco C. Robles Hernandez and published by Springer. This book was released on 2017-07-02 with total page 253 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book details aluminum alloys with special focus on the aluminum silicon (Al‐Si) systems – that are the most abundant alloys second only to steel. The authors include a description of the manufacturing principles, thermodynamics, and other main characteristics of Al‐Si alloys. Principles of processing, testing, and in particular applications in the Automotive, Aeronautical and Aerospace fields are addressed.
Download or read book Handbook of Manufacturing Engineering and Technology written by Andrew Y. C. Nee and published by Springer. This book was released on 2014-10-31 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Springer Reference Work Handbook of Manufacturing Engineering and Technology provides overviews and in-depth and authoritative analyses on the basic and cutting-edge manufacturing technologies and sciences across a broad spectrum of areas. These topics are commonly encountered in industries as well as in academia. Manufacturing engineering curricula across universities are now essential topics covered in major universities worldwide.
Download or read book Semiconductor Laser Engineering Reliability and Diagnostics written by Peter W. Epperlein and published by John Wiley & Sons. This book was released on 2013-01-25 with total page 522 pages. Available in PDF, EPUB and Kindle. Book excerpt: This reference book provides a fully integrated novel approach to the development of high-power, single-transverse mode, edge-emitting diode lasers by addressing the complementary topics of device engineering, reliability engineering and device diagnostics in the same book, and thus closes the gap in the current book literature. Diode laser fundamentals are discussed, followed by an elaborate discussion of problem-oriented design guidelines and techniques, and by a systematic treatment of the origins of laser degradation and a thorough exploration of the engineering means to enhance the optical strength of the laser. Stability criteria of critical laser characteristics and key laser robustness factors are discussed along with clear design considerations in the context of reliability engineering approaches and models, and typical programs for reliability tests and laser product qualifications. Novel, advanced diagnostic methods are reviewed to discuss, for the first time in detail in book literature, performance- and reliability-impacting factors such as temperature, stress and material instabilities. Further key features include: practical design guidelines that consider also reliability related effects, key laser robustness factors, basic laser fabrication and packaging issues; detailed discussion of diagnostic investigations of diode lasers, the fundamentals of the applied approaches and techniques, many of them pioneered by the author to be fit-for-purpose and novel in the application; systematic insight into laser degradation modes such as catastrophic optical damage, and a wide range of technologies to increase the optical strength of diode lasers; coverage of basic concepts and techniques of laser reliability engineering with details on a standard commercial high power laser reliability test program. Semiconductor Laser Engineering, Reliability and Diagnostics reflects the extensive expertise of the author in the diode laser field both as a top scientific researcher as well as a key developer of high-power highly reliable devices. With invaluable practical advice, this new reference book is suited to practising researchers in diode laser technologies, and to postgraduate engineering students.
Download or read book Welding and Joining of Magnesium Alloys written by L Liu and published by Woodhead Publishing. This book was released on 2010-10-28 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Due to the wide application of magnesium alloys in metals manufacturing, it is very important to employ a reliable method of joining these reactive metals together and to other alloys. Welding and joining of magnesium alloys provides a detailed review of both established and new techniques for magnesium alloy welding and their characteristics, limitations and applications. Part one covers general issues in magnesium welding and joining, such as welding materials, metallurgy and the joining of magnesium alloys to other metals such as aluminium and steel. The corrosion and protection of magnesium alloy welds are also discussed. In part two particular welding and joining techniques are reviewed, with chapters covering such topics as inert gas welding, metal inert gas welding and laser welding, as well as soldering, mechanical joining and adhesive bonding. The application of newer techniques to magnesium alloys, such as hybrid laser-arc welding, activating flux tungsten inert gas welding and friction stir, is also discussed. With its distinguished editor and expert team of contributors, Welding and joining of magnesium alloys is a comprehensive reference for producers of primary magnesium and those using magnesium alloys in the welding, automotive and other such industries, as well as academic researchers in metallurgy and materials science.
Download or read book Materials written by Michael F. Ashby and published by Butterworth-Heinemann. This book was released on 2013-10-09 with total page 899 pages. Available in PDF, EPUB and Kindle. Book excerpt: Materials, Third Edition, is the essential materials engineering text and resource for students developing skills and understanding of materials properties and selection for engineering applications. This new edition retains its design-led focus and strong emphasis on visual communication while expanding its inclusion of the underlying science of materials to fully meet the needs of instructors teaching an introductory course in materials. A design-led approach motivates and engages students in the study of materials science and engineering through real-life case studies and illustrative applications. Highly visual full color graphics facilitate understanding of materials concepts and properties. For instructors, a solutions manual, lecture slides, online image bank, and materials selection charts for use in class handouts or lecture presentations are available at http://textbooks.elsevier.com. The number of worked examples has been increased by 50% while the number of standard end-of-chapter exercises in the text has been doubled. Coverage of materials and the environment has been updated with a new section on Sustainability and Sustainable Technology. The text meets the curriculum needs of a wide variety of courses in the materials and design field, including introduction to materials science and engineering, engineering materials, materials selection and processing, and materials in design. Design-led approach motivates and engages students in the study of materials science and engineering through real-life case studies and illustrative applications Highly visual full color graphics facilitate understanding of materials concepts and properties Chapters on materials selection and design are integrated with chapters on materials fundamentals, enabling students to see how specific fundamentals can be important to the design process For instructors, a solutions manual, lecture slides, online image bank and materials selection charts for use in class handouts or lecture presentations are available at http://textbooks.elsevier.com Links with the Cambridge Engineering Selector (CES EduPack), the powerful materials selection software. See www.grantadesign.com for information NEW TO THIS EDITION: Text and figures have been revised and updated throughout The number of worked examples has been increased by 50% The number of standard end-of-chapter exercises in the text has been doubled Coverage of materials and the environment has been updated with a new section on Sustainability and Sustainable Technology
Download or read book Welding Processes Handbook written by Klas Weman and published by Woodhead Publishing. This book was released on 2003 with total page 208 pages. Available in PDF, EPUB and Kindle. Book excerpt: Welding processes handbookis an introductory guide to all of the main welding processes. It is specifically designed for students on EWF courses and newcomers to welding and is suitable as a textbook for European welding courses in accordance with guidelines from the European Welding Federation. Welding processes and equipment necessary for each process are described so that they can be applied to all instruction levels required by the EWF and the important areas of welded joint design, quality assurance and costing are also covered in detail.
Download or read book Welding Engineering written by David H. Phillips and published by John Wiley & Sons. This book was released on 2016-02-16 with total page 308 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides an introduction to all of the important topics in welding engineering. It covers a broad range of subjects and presents each topic in a relatively simple, easy to understand manner, with emphasis on the fundamental engineering principles. • Comprehensive coverage of all welding engineering topics • Presented in a simple, easy to understand format • Emphasises concepts and fundamental principles
Download or read book Engineering Materials 2 written by Michael F. Ashby and published by Elsevier. This book was released on 2014-06-28 with total page 380 pages. Available in PDF, EPUB and Kindle. Book excerpt: Provides a thorough explanation of the basic properties of materials; of how these can be controlled by processing; of how materials are formed, joined and finished; and of the chain of reasoning that leads to a successful choice of material for a particular application. The materials covered are grouped into four classes: metals, ceramics, polymers and composites. Each class is studied in turn, identifying the families of materials in the class, the microstructural features, the processes or treatments used to obtain a particular structure and their design applications. The text is supplemented by practical case studies and example problems with answers, and a valuable programmed learning course on phase diagrams.
Download or read book Introduction to Permanent Plug and Abandonment of Wells written by Mahmoud Khalifeh and published by Springer Nature. This book was released on 2020-01-27 with total page 285 pages. Available in PDF, EPUB and Kindle. Book excerpt: This open access book offers a timely guide to challenges and current practices to permanently plug and abandon hydrocarbon wells. With a focus on offshore North Sea, it analyzes the process of plug and abandonment of hydrocarbon wells through the establishment of permanent well barriers. It provides the reader with extensive knowledge on the type of barriers, their functioning and verification. It then discusses plug and abandonment methodologies, analyzing different types of permanent plugging materials. Last, it describes some tests for verifying the integrity and functionality of installed permanent barriers. The book offers a comprehensive reference guide to well plugging and abandonment (P&A) and well integrity testing. The book also presents new technologies that have been proposed to be used in plugging and abandoning of wells, which might be game-changing technologies, but they are still in laboratory or testing level. Given its scope, it addresses students and researchers in both academia and industry. It also provides information for engineers who work in petroleum industry and should be familiarized with P&A of hydrocarbon wells to reduce the time of P&A by considering it during well planning and construction.
Download or read book Failure Analysis of Heat Treated Steel Components written by Lauralice de Campos Franceschini Canale and published by ASM International. This book was released on 2008 with total page 651 pages. Available in PDF, EPUB and Kindle. Book excerpt:
