Download or read book Understanding and Control of Transport in Advanced Tokamak Regimes in DIII D written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Transport phenomena are studied in Advanced Tokamak (AT) regimes in the DIII-D tokamak[Plasma Physics and Controlled Nuclear Fusion Research, 1986 (International Atomics Energy Agency, Vienna, 1987), Vol. I, p. 159], with the goal of developing understanding and control during each of three phases: Formation of the internal transport barrier (ITB) with counter neutral beam injection takes place when the heating power exceeds a threshold value of about 9 MW, contrasting to CO-NBI injection, where P[sub threshold]

Download or read book Frontiers in Fusion Research II written by Mitsuru Kikuchi and published by Springer. This book was released on 2015-09-03 with total page 412 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book reviews recent progress in our understanding of tokamak physics related to steady state operation, and addresses the scientific feasibility of a steady state tokamak fusion power system. It covers the physical principles behind continuous tokamak operation and details the challenges remaining and new lines of research towards the realization of such a system. Following a short introduction to tokamak physics and the fundamentals of steady state operation, later chapters cover parallel and perpendicular transport in tokamaks, MHD instabilities in advanced tokamak regimes, control issues, and SOL and divertor plasmas. A final chapter reviews key enabling technologies for steady state reactors, including negative ion source and NBI systems, Gyrotron and ECRF systems, superconductor and magnet systems, and structural materials for reactors. The tokamak has demonstrated an excellent plasma confinement capability with its symmetry, but has an intrinsic drawback with its pulsed operation with inductive operation. Efforts have been made over the last 20 years to realize steady state operation, most promisingly utilizing bootstrap current. Frontiers in Fusion Research II: Introduction to Modern Tokamak Physics will be of interest to graduate students and researchers involved in all aspects of tokamak science and technology.

Download or read book Enhanced Confinement Regimes and Control Technology in the DIII D Tokamak written by and published by . This book was released on 1993 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: Advanced tokamak performance has been demonstrated in the DIII-D tokamak in a series of experiments which brought together developments in technology and improved understanding of the physical principles underlying tokamak operation. The achievement of greatly improved confinement coupled with development of new systems for real time plasma control have permitted investigation of the heretofore hidden or poorly controlled variables which together determine global confinement. These experiments, which included work in transport and control of the plasma boundary, point toward development of operationally and economically attractive reactors based on the tokamak. Some of these experiments are described.

Download or read book Advanced Tokamak Research on the DIII D Tokamak written by and published by . This book was released on 1994 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Advanced Tokamak Physics Experiments on DIII D written by and published by . This book was released on 1998 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Quiescent Double Barrier H Mode Plasmas in the DIII D Tokamak written by and published by . This book was released on 2000 with total page 26 pages. Available in PDF, EPUB and Kindle. Book excerpt: High confinement (H-mode) operation is the choice for next-step tokamak devices based either on conventional or advanced tokamak physics. This choice, however, comes at a significant cost for both the conventional and advanced tokamaks because of the effects of edge localized modes (ELMs). ELMs can produce significant erosion in the divertor and can affect the beta limit and reduced core transport regions needed for advanced tokamak operation. Experimental results from DIII-D this year have demonstrated a new operating regime, the quiescent H-mode regime, which solves these problems. We have achieved quiescent H-mode operation which is ELM-free and yet has good density and impurity control. In addition, we have demonstrated that an internal transport barrier can be produced and maintained inside the H-mode edge barrier for long periods of time (>3.5 seconds or>25 energy confinement times [tau]{sub E}), yielding a quiescent double barrier regime. By slowly ramping the input power, we have achieved [beta]{sub N} H89 = 7 for up to 5 times the [tau]{sub E} of 150 ms. The [beta]{sub N} H89 values of 7 substantially exceed the value of 4 routinely achieved in standard ELMing H-mode. The key factors in creating the quiescent H-mode operation are neutral beam injection in the direction opposite to the plasma current (counter injection) plus cryopumping to reduce the density. Density and impurity control in the quiescent H-mode is possible because of the presence of an edge magnetic hydrodynamic (MHD) oscillation, the edge harmonic oscillation, which enhances the edge particle transport while leaving the energy transport unaffected.

Download or read book DIII D Advanced Tokamak Research Overview written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper reviews recent progress in the development of long-pulse, high performance discharges on the DIII-D tokamak. It is highlighted by a discharge achieving simultaneously[beta][sub N]H of 9, bootstrap current fraction of 0.5, noninductive current fraction of 0.75, and sustained for 16 energy confinement times. The physics challenge has changed in the long-pulse regime. Non-ideal MHD modes are limiting the stability, fast ion driven modes may play a role in fast ion transport which limits the stored energy and plasma edge behavior can affect the global performance. New control tools are being developed to address these issues.

Download or read book ADVANCED TOKAMAK OPERATION USING THE DIII D PLASMA CONTROL SYSTEM written by and published by . This book was released on 2002 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt: A271 ADVANCED TOKAMAK OPERATION USING THE DIII-D PLASMA CONTROL SYSTEM. The principal focus of experimental operations in the DIII-D tokamak is the advanced tokamak (AT) regime to achieve, which requires highly integrated and flexible plasma control. In a high performance advanced tokamak, accurate regulation of the plasma boundary, internal profiles, pumping, fueling, and heating must be well coordinated with MHD control action to stabilize such instabilities as tearing modes and resistive wall modes. Sophisticated monitors of the operational regime must provide detection of off-normal conditions and trigger appropriate safety responses with acceptable levels of reliability. Many of these capabilities are presently implemented in the DIII-D plasma control system (PCS), and are now in frequent or routine operational use. The present work describes recent development, implementation, and operational experience with AT regime control elements for equilibrium control, MHD suppression, and off-normal event detection and response.

Download or read book HIGH PERFORMANCE ADVANCED TOKAMAK REGIMES FOR NEXT STEP EXPERIMENTS written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: OAK-B135 Advanced Tokamak (AT) research in DIII-D seeks to provide a scientific basis for steady-state high performance operation in future devices. These regimes require high toroidal beta to maximize fusion output and poloidal beta to maximize the self-driven bootstrap current. Achieving these conditions requires integrated, simultaneous control of the current and pressure profiles, and active magnetohydrodynamic (MHD) stability control. The building blocks for AT operation are in hand. Resistive wall mode stabilization via plasma rotation and active feedback with non-axisymmetric coils allows routine operation above the no-wall beta limit. Neoclassical tearing modes are stabilized by active feedback control of localized electron cyclotron current drive (ECCD). Plasma shaping and profile control provide further improvements. Under these conditions, bootstrap supplies most of the current. Steady-state operation requires replacing the remaining Ohmic current, mostly located near the half-radius, with noninductive external sources. In DIII-D this current is provided by ECCD, and nearly stationary AT discharges have been sustained with little remaining Ohmic current. Fast wave current drive is being developed to control the central magnetic shear. Density control, with divertor cryopumps, of AT discharges with edge localized moding (ELMing) H-mode edges facilitates high current drive efficiency at reactor relevant collisionalities. A sophisticated plasma control system allows integrated control of these elements. Close coupling between modeling and experiment is key to understanding the separate elements, their complex nonlinear interactions, and their integration into self-consistent high performance scenarios. Progress on this development, and its implications for next-step devices, will be illustrated by results of recent experiment and simulation efforts.

Download or read book Current Profile Modeling to Extend the Duration of High Performance Advanced Tokamak Modes in DIII D written by and published by . This book was released on 1998 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: In DIII-D, as in a number of tokamaks, high performance is obtained with various optimized magnetic shear configurations that exhibit internal transport barriers. Negative central shear (NCS) discharges are created transiently during the current ramp-up by auxiliary heating and current drive from neutral beam injection. Both q{sub min} and the radius at which it occurs, [rho]{sub qmin}, decrease with time as the Ohmic current diffuses inward. The q-profiles calculated using EFIT with external magnetic and Motional Stark Effect (MSE) measurements as constraints are comparable to those calculated with the Corsica code, a time-dependent, 2D equilibrium and 1D transport modeling code. Corsica is used to predict the temporal evolution of the current density from a combination of measured profiles, transport models and neoclassical resistivity. Using these predictive capabilities, the authors are exploring methods for increasing the duration and [rho]{sub qmin} of the NCS configuration by local control of the current density profile with simulations of the possible control available from the electron cyclotron heating and current drive system currently being upgraded on DIII-D. Their intention is not to do a detailed investigation of transport models but rather to provide a reasonable model of heat conductivity to be able to simulate effects of electron cyclotron heating (ECH) and current drive (ECCD) on confinement in NCS configurations. The authors adjust free parameters (c, c1 and c2) in the model to obtain a reasonable representation of the temporal evolution of electron and ion temperature profiles consistent with those measured in selected DIII-D shots. In all cases, they use the measured density profiles rather than self-consistently solve for particle sources and particle transport at this time.

Download or read book State Services for the Blind in California written by and published by . This book was released on 1949 with total page 40 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Overview of Recent Experimental Results from the DIII D Advanced Tokamak Program written by and published by . This book was released on 2002 with total page 39 pages. Available in PDF, EPUB and Kindle. Book excerpt: OAK A271 OVERVIEW OF RECENT EXPERIMENTAL RESULTS FROM THE DIII-D ADVANCED TOKAMAK PROGRAM. The DIII-D research program is developing the scientific basis for advanced tokamak (AT) modes of operation in order to enhance the attractiveness of the tokamak as an energy producing system. Since the last International Atomic Energy Agency (IAEA) meeting, they have made significant progress in developing the building blocks needed for AT operation: (1) they have doubled the magnetohydrodynamic (MHD) stable tokamak operating space through rotational stabilization of the resistive wall mode; (2) using this rotational stabilization, they have achieved [beta]{sub N}H9 e"10 for 4 [tau]{sub E} limited by the neoclassical tearing mode; (3) using real-time feedback of the electron cyclotron current drive (ECCD) location, they have stabilized the (m, n) = (3,2) neoclassical tearing mode and then increased [beta]{sub T} by 60%; (4) they have produced ECCD stabilization of the (2,1) neoclassical tearing mode in initial experiments; (5) they have made the first integrated AT demonstration discharges with current profile control using ECCD; (6) ECCD and electron cyclotron heating (ECH) have been used to control the pressure profile in high performance plasmas; and (7) they have demonstrated stationary tokamak operation for 6.5 s (36 [tau]{sub E}) at the same fusion gain parameter of [beta]{sub N}H9/q952 H"0.4 as ITER but at much higher q95 = 4.2. The authors have developed general improvements applicable to conventional and advanced tokamak operating modes: (1) they have an existence proof of a mode of tokamak operation, quiescent H-mode, which has no pulsed, ELM heat load to the divertor and which can run for long periods of time (3.8 s or 25 [tau]{sub E}) with constant density and constant radiated power; (2) they have demonstrated real-time disruption detection and mitigation for vertical disruption events using high pressure gas jet injection of noble gases; (3) they have found that the heat and particle fluxes to the inner strike points of balanced, double-null divertors are much smaller than to the outer strike points. They have made detailed investigations of the edge pedestal and SOL: (1) Atomic physics and plasma physics both play significant roles in setting the width of the edge density barrier in H-mode; (2) ELM heat flux conducted to the divertor decreases as density increases; (3) Intermittent, bursty transport contributes to cross field particle transport in the scrape-off layer (SOL) of H-mode and, especially, L-mode plasmas.

Download or read book Progress Towards Sustainment of Advanced Tokamak Modes in DIII D written by and published by . This book was released on 1998 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book CONTROL OF MHD STABILITY IN DIII D ADVANCED TOKAMAK DISCHARGES written by M. MURAKAMI and published by . This book was released on 2003 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Physics of Advanced Tokamaks written by and published by . This book was released on 1997 with total page 19 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Motional Stark Effect Upgrades on DIII D written by and published by . This book was released on 1994 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: The measurement and control of the plasma current density profile (or q profile) is critical to the advanced tokamak program on DIII-D.A complete understanding of the stability and transport properties of advanced operating regimes requires detail poloidal field measurements over the entire plasma radius from the core to the edge. In support of this effort, the authors have recently completed an upgrade of the existing MSE diagnostic, increasing the number of channels from 8 to 16. A new viewing geometry has been added to the outer edge of the plasma which improves the radial resolution in this region from 10 cm to

Download or read book Optimized Profiles for Improved Confinement and Stability in the DIII D Tokamak written by and published by . This book was released on 1995 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: Simultaneous achievement of high energy confinement, [tau]{sub E}, and high plasma beta, [beta], leads to an economically attractive compact tokamak fusion reactor. High confinement enhancement, H = [tau]{sub E}/[tau]{sub E-ITER89P} = 4, and high normalized beta [beta]{sub N} = [beta]/(I/aB) = 6%-m-T/MA, have been obtained in DIII-D experimental discharges. These improved confinement and/or improved stability limits are observed in several DIII-D high performance operational regimes: VH-mode, high l{sub i} H-mode, second stable core, and high beta poloidal. The authors have identified several important features of the improved performance in these discharges: details of the plasma shape, toroidal rotation or ExB flow profile, q profile and current density profile, and pressure profile. From the improved physics understanding of these enhanced performance regimes, they have developed operational scenarios which maintain the essential features of the improved confinement and which increase the stability limits using localized current profile control. The stability limit is increased by modifying the interior safety factor profile to be nonmonotonic with high central q, while maintaining the edge current density consistent with the improved transport regimes and the high edge bootstrap current. They have calculated high beta equilibria with [beta]{sub N} = 6.5, stable to ideal n = 1 kinks and stable to ideal ballooning modes. The safety factor at the 95% flux surface is 6, the central q value is 3.9 and the minimum in q is 2.6. The current density profile is maintained by the natural profile of the bootstrap current, and a modest amount of electron cyclotron current drive.