EBookClubs

Read Books & Download eBooks Full Online

EBookClubs

Read Books & Download eBooks Full Online

Book Two Phase Flow Through Orifice Plates in a Large Diameter Horizontal Pipeline

Download or read book Two Phase Flow Through Orifice Plates in a Large Diameter Horizontal Pipeline written by Saleh M. Mahmoud and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Two Phase Flow in a Large Diameter Horizontal Pipeline

Download or read book Two Phase Flow in a Large Diameter Horizontal Pipeline written by Tarig Ali Al-Bkoush and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Two phase Pressure Drop in Piping Components

Download or read book Two phase Pressure Drop in Piping Components written by D. E. Fitzsimmons and published by . This book was released on 1964 with total page 74 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Two phase Flow in Pipelines and Heat Exchangers

Download or read book Two phase Flow in Pipelines and Heat Exchangers written by Duncan Chisholm and published by . This book was released on 1983 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book A Study of Two phase Flow in a Large Diameter Horizontal Pipeline and the Measurement of Interfacial Level Gradient in Smooth Stratified Flow Conditions

Download or read book A Study of Two phase Flow in a Large Diameter Horizontal Pipeline and the Measurement of Interfacial Level Gradient in Smooth Stratified Flow Conditions written by Essaied Masoud Ali and published by . This book was released on 1992 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This study investigates the behaviour of two-phase flow in large diameter horizontal pipelines. The study was divided into two main parts: (i) General two-phase flow in 203 mm diameter pipeline, where the pressure drop and void fraction were measured. The pressure drop was measured using 23 bottom tapping points along a 34 m test section. The results were compared with six well known pressure drop models; these models did not allow for diameter size effect, it was therefore not surprising that good agreement was not achieved. A traversing y-ray apparatusw as designed and constructed for the measurements of void fraction. Void fraction measurements were compared with geometrical void fraction calculation, and very satisfactory agreements were obtained. The apparatus was also tested under a different number of chordal positions (steps) to determine the influence of the number of steps on the accuracy of the results. The void fraction results were compared with nine correlations found in the literature; the effect of pipe size was clear. A flow pattern map was also drawn for a 203 mm pipeline, which covered all the possible flow patterns (annular flow could not be obtained in this size of pipe, with the available air supply), and compared with three well known flow pattern maps, where a little agreement was found. (ii) The measurement of interfacial level gradient in the smooth stratified flow conditions. Two depth gauges (probes) were designed, constructed and calibrated for the measurement of the water level change along the test section. The two probes were placed 12 metres apart in the test section, where the flow conditions considered settled. The measurement accuracy of the probes was within 1 mm of liquid height, i. e. less than 1%. Two theoretical models in the field of stratified flow were tested and then modified to improve their ability to predict the present data, and perhaps 11 other data obtained from large diameter pipelines. A model based on the present set of data, following Bishop et. al (1986) approach was proposed, which predicts the present data within RMS of 8%.

Book Two Phase Gas Liquid Flow in Pipes with Different Orientations

Download or read book Two Phase Gas Liquid Flow in Pipes with Different Orientations written by Afshin J. Ghajar and published by Springer Nature. This book was released on 2020-03-14 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book provides design engineers using gas-liquid two-phase flow in different industrial applications the necessary fundamental understanding of the two-phase flow variables. Two-phase flow literature reports a plethora of correlations for determination of flow patterns, void fraction, two- phase pressure drop and non-boiling heat transfer correlations. However, the validity of a majority of these correlations is restricted over a narrow range of two -phase flow conditions. Consequently, it is quite a challenging task for the end user to select an appropriate correlation/model for the type of two-phase flow under consideration. Selection of a correct correlation also requires some fundamental understanding of the two-phase flow physics and the underlying principles/assumptions/limitations associated with these correlations. Thus, it is of significant interest for a design engineer to have knowledge of the flow patterns and their transitions and their influence on two-phase flow variables. To address some of these issues and facilitate selection of appropriate two-phase flow models, this volume presents a succinct review of the flow patterns, void fraction, pressure drop and non-boiling heat transfer phenomenon and recommend some of the well scrutinized modeling techniques.

Book Two phase Adiabatic Flow Through Gate Valve Inserted Into Horizontal Large Diameter Pipeline

Download or read book Two phase Adiabatic Flow Through Gate Valve Inserted Into Horizontal Large Diameter Pipeline written by Salah Ali A. Masheiti and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book An Experimental Study of Two phase Flow in Inclined Pipes

Download or read book An Experimental Study of Two phase Flow in Inclined Pipes written by Howard Dale Beggs and published by . This book was released on 1987 with total page 126 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book A Study on Two phase Flow in a Large Diameter Horizontal Pipeline

Download or read book A Study on Two phase Flow in a Large Diameter Horizontal Pipeline written by Jamaluddin Md Sheriff and published by . This book was released on 1986 with total page 428 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book A Study of Two phase Flow in a Large Diameter Horizontal Pipeline

Download or read book A Study of Two phase Flow in a Large Diameter Horizontal Pipeline written by Abdunaser Ali Saadawi and published by . This book was released on 1991 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Scientific and Technical Aerospace Reports

Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1966 with total page 1492 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Two Phase Flow Patterns and Pressure Drop Studies in a Large Diameter Horizontal Tube

Download or read book Two Phase Flow Patterns and Pressure Drop Studies in a Large Diameter Horizontal Tube written by Shatub Magid Hassan and published by . This book was released on 1983 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Book Orifice Plates and Venturi Tubes

Download or read book Orifice Plates and Venturi Tubes written by Michael Reader-Harris and published by Springer. This book was released on 2015-04-29 with total page 406 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book gives the background to differential-pressure flow measurement and goes through the requirements explaining the reason for them. For those who want to use an orifice plate or a Venturi tube the standard ISO 5167 and its associated Technical Reports give the instructions required. However, they rarely tell the users why they should follow certain instructions. This book helps users of the ISO standards for orifice plates and Venturi tubes to understand the reasons why the standards are as they are, to apply them effectively, and to understand the consequences of deviations from the standards.