Download or read book Transport Membrane Condenser for Water and Energy Recovery from Power Plant Flue Gas written by and published by . This book was released on 2012 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The new waste heat and water recovery technology based on a nanoporous ceramic membrane vapor separation mechanism has been developed for power plant flue gas application. The recovered water vapor and its latent heat from the flue gas can increase the power plant boiler efficiency and reduce water consumption. This report describes the development of the Transport Membrane Condenser (TMC) technology in details for power plant flue gas application. The two-stage TMC design can achieve maximum heat and water recovery based on practical power plant flue gas and cooling water stream conditions. And the report includes: Two-stage TMC water and heat recovery system design based on potential host power plant coal fired flue gas conditions; Membrane performance optimization process based on the flue gas conditions, heat sink conditions, and water and heat transport rate requirement; Pilot-Scale Unit design, fabrication and performance validation test results. Laboratory test results showed the TMC system can exact significant amount of vapor and heat from the flue gases. The recovered water has been tested and proved of good quality, and the impact of SO2 in the flue gas on the membrane has been evaluated. The TMC pilot-scale system has been field tested with a slip stream of flue gas in a power plant to prove its long term real world operation performance. A TMC scale-up design approach has been investigated and an economic analysis of applying the technology has been performed.

Download or read book Energy and Water Recovery with Transport Membrane Condenser written by Dexin Wang and published by . This book was released on 2013 with total page 98 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Simultaneous Waste Heat and Water Recovery from Power Plant Flue Gases for Advanced Energy Systems written by and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This final report presents the results of a two-year technology development project carried out by a team of participants sponsored by the Department of Energy (DOE). The objective of this project is to develop a membrane-based technology to recover both water and low grade heat from power plant flue gases. Part of the recovered high-purity water and energy can be used directly to replace plant boiler makeup water as well as improving its efficiency, and the remaining part of the recovered water can be used for Flue Gas Desulfurization (FGD), cooling tower water makeup or other plant uses. This advanced version Transport Membrane Condenser (TMC) with lower capital and operating costs can be applied to existing plants economically and can maximize waste heat and water recovery from future Advanced Energy System flue gases with CO2 capture in consideration, which will have higher moisture content that favors the TMC to achieve higher efficiency.

Download or read book Comprehensive Membrane Science and Engineering written by Enrico Drioli and published by Elsevier. This book was released on 2017-07-20 with total page 1709 pages. Available in PDF, EPUB and Kindle. Book excerpt: Comprehensive Membrane Science and Engineering, Second Edition, Four Volume Set is an interdisciplinary and innovative reference work on membrane science and technology. Written by leading researchers and industry professionals from a range of backgrounds, chapters elaborate on recent and future developments in the field of membrane science and explore how the field has advanced since the previous edition published in 2010. Chapters are written by academics and practitioners across a variety of fields, including chemistry, chemical engineering, material science, physics, biology and food science. Each volume covers a wide spectrum of applications and advanced technologies, such as new membrane materials (e.g. thermally rearranged polymers, polymers of intrinsic microporosity and new hydrophobic fluoropolymer) and processes (e.g. reverse electrodialysis, membrane contractors, membrane crystallization, membrane condenser, membrane dryers and membrane emulsifiers) that have only recently proved their full potential for industrial application. This work covers the latest advances in membrane science, linking fundamental research with real-life practical applications using specially selected case studies of medium and large-scale membrane operations to demonstrate successes and failures with a look to future developments in the field. Contains comprehensive, cutting-edge coverage, helping readers understand the latest theory Offers readers a variety of perspectives on how membrane science and engineering research can be best applied in practice across a range of industries Provides the theory behind the limits, advantages, future developments and failure expectations of local membrane operations in emerging countries

Download or read book Membranes for Industrial Wastewater Recovery and Re use written by S. Judd and published by Elsevier. This book was released on 2003-04-25 with total page 320 pages. Available in PDF, EPUB and Kindle. Book excerpt: In a world in which legislation promotes the recycling of wastewater new technologies are emerging that can fulfil such a remit. The papers that comprise this volume explore those technologies and explain what is driving and what is preventing their widespread implementation.

Download or read book Thermal Energy written by Yatish T. Shah and published by CRC Press. This book was released on 2018-01-12 with total page 1112 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book details sources of thermal energy, methods of capture, and applications. It describes the basics of thermal energy, including measuring thermal energy, laws of thermodynamics that govern its use and transformation, modes of thermal energy, conventional processes, devices and materials, and the methods by which it is transferred. It covers 8 sources of thermal energy: combustion, fusion (solar) fission (nuclear), geothermal, microwave, plasma, waste heat, and thermal energy storage. In each case, the methods of production and capture and its uses are described in detail. It also discusses novel processes and devices used to improve transfer and transformation processes.

Download or read book Hollow Fiber Membrane Contactors written by Anil K. Pabby and published by CRC Press. This book was released on 2020-11-23 with total page 325 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book on hollow fiber contractors presents an up-to-date compilation of the latest developments and milestones in this membrane technology. Hollow Fiber Membrane Contactors: Module Fabrication, Design and Operation, and Potential Applications provides a comprehensive discussion of hollow fiber membrane applications (including a few case studies) in biotechnology, chemical, food, and nuclear engineering. The chapters in this book have been classified using the following, based on different ways of contacting fluids with each other: Gas-liquid contacting; Liquid-liquid contacting; Supported liquid membrane; Supported gas membrane; Fluid-fluid contacting. Other features include: Discusses using non-dispersive solvent extraction, hollow fiber strip dispersion, hollow fiber supported liquid membranes and role of process intensification in integrated use of these processes Provides technical and economic perspectives with several case studies related to specific scenarios Demonstrates module fabrication, design, operation and maintenance of hollow fiber contactors for different applications and performance Presents discussion on newer concepts like membrane emulsification, membrane nanoprecipitation, membrane crystallization and membrane condenser Special focus on emerging areas such as the use of hollow fiber contactor in back end of nuclear fuel cycle, membrane distillation, dehumidification of air and gas absorption and stripping Discusses theoretical analysis including computational modeling of different hollow fiber membrane processes, and presents emphasis on newly developed area of hollow fiber membrane based analytical techniques Presents discussion on upcoming area dealing with hollow fiber contactors-based technology in fermentation and enzymatic transformation and in chiral separations This book is equally suited for newcomers to the field, as well as for engineers and scientists that have basic knowledge in this field but are interested in obtaining more information about specific future applications.

Download or read book Membrane Engineering written by Enrico Drioli and published by Walter de Gruyter GmbH & Co KG. This book was released on 2018-12-17 with total page 458 pages. Available in PDF, EPUB and Kindle. Book excerpt: Modern membrane science and technology aids engineers in developing and designing more efficient and environmentally-friendly processes. The optimal material and membrane selection as well as applications in the many involved industries are provided. This work is the ideal introduction for engineers working in membrane science and applications (wastewater, desalination, adsorption, and catalysis), process engineers in separation science, biologists and biochemists, environmental scientists, and most of all students. Its multidisciplinary approach also stimulates thinking of hybrid technologies for current and future life-saving applications (artificial organs, drug delivery).

Download or read book Optimization of the Fin Configuration of Air cooled Condensing Wet Electrostatic Precipitator for Water Recovery from Power Plant Flue Gas written by Yanhui Chen and published by . This book was released on 2013 with total page 121 pages. Available in PDF, EPUB and Kindle. Book excerpt: Growing concerns about freshwater availability increase the pressure on power plant to reduce water usages. The Innovations for Existing Plants Program from the US Department of Energy's National Energy Technology Laboratory is developing technologies in 5 categories to reduce water use. One of them is reclaiming water from combustion flue gas for usage as cooling water make-up. Considering that heat transfer efficiency is significantly enhanced in both gas and liquid phases due to corona wind and wetted wall inside the wet ESPs, a innovative technology of applying air-cooled condensing wet ESP for water recovery from flue gas was proposed. Additionally, the preliminary results show that the quantities of water extracted by the proposed air-cooled condensing wet ESP far exceed the FGD water make-up. However, the optimization of wet ESP's fin configuration is at an early stage, and the operation condition effects on the determination of optimal fin's configuration are not investigated yet. Thus, in this research, an analytical model of heat process in air-cooled condensing wet ESP system was developed to predict the heat transferred from flue gas to cooling air and the condensation rate of water vapor in the flue gas. Optimum fin's thickness and spacing under the operation conditions of ̊80°F ambient temperature and 5MW fan power were evaluated. In addition, the effects of fan power and ambient temperature on the determination of optimal fin's configuration and water recovery are investigated. It is found that the optimal fin's thickness is 0.25 inches, and the optimal fin's spacing is 0.5 inches with 5MW fan power, and outside cooling air temperature of ̊80°F. Under these optimized parameters, the total amount of water recovery reaches 557.725 gpm. Furthermore, changing ambient temperature has no effects on optimal fin's configuration, while increasing fan power make the optimal fin's thickness and spacing shift to lower value.

Download or read book Renewable Energy Systems written by Martin Kaltschmitt and published by Springer. This book was released on 2012-12-06 with total page 1898 pages. Available in PDF, EPUB and Kindle. Book excerpt: Humanity is facing a steadily diminishing supply of fossil fuels, causing researchers, policy makers, and the population as a whole to turn increasingly to alternative and especially renewable sources of energy to make up this deficit. Gathering over 80 peer-reviewed entries from the Encyclopedia of Sustainability Science and Technologies, Renewable Energy Systems provides an authoritative introduction to a wide variety of renewable energy sources. State-of-the-art coverage includes geothermal power stations, ocean energy, renewable energy from biomass, waste to energy, and wind power. This comprehensive, two-volume work provides an excellent introduction for those entering these fields, as well as new insights for advanced researchers, industry experts, and decision makers.

Download or read book Steam Generators and Waste Heat Boilers written by V. Ganapathy and published by CRC Press. This book was released on 2014-10-10 with total page 544 pages. Available in PDF, EPUB and Kindle. Book excerpt: Incorporates Worked-Out Real-World Problems Steam Generators and Waste Heat Boilers: For Process and Plant Engineers focuses on the thermal design and performance aspects of steam generators, HRSGs and fire tube, water tube waste heat boilers including air heaters, and condensing economizers. Over 120 real-life problems are fully worked out which will help plant engineers in evaluating new boilers or making modifications to existing boiler components without assistance from boiler suppliers. The book examines recent trends and developments in boiler design and technology and presents novel ideas for improving boiler efficiency and lowering gas pressure drop. It helps plant engineers understand and evaluate the performance of steam generators and waste heat boilers at any load. Learn How to Independently Evaluate the Thermal Performance of Boilers and Their Components This book begins with basic combustion and boiler efficiency calculations. It then moves on to estimation of furnace exit gas temperature (FEGT), furnace duty, view factors, heat flux, and boiler circulation calculations. It also describes trends in large steam generator designs such as multiple-module; elevated drum design types of boilers such as D, O, and A; and forced circulation steam generators. It illustrates various options to improve boiler efficiency and lower operating costs. The author addresses the importance of flue gas analysis, fire tube versus water tube boilers used in chemical plants, and refineries. In addition, he describes cogeneration systems; heat recovery in sulfur plants, hydrogen plants, and cement plants; and the effect of fouling factor on performance. The book also explains HRSG simulation process and illustrates calculations for complete performance evaluation of boilers and their components. Helps plant engineers make independent evaluations of thermal performance of boilers before purchasing them Provides numerous examples on boiler thermal performance calculations that help plant engineers develop programming codes with ease Follows the metric and SI system, and British units are shown in parentheses wherever possible Includes calculation procedures for the basic sizing and performance evaluation of a complete steam generator or waste heat boiler system and their components with appendices outlining simplified procedures for estimation of heat transfer coefficients Steam Generators and Waste Heat Boilers: For Process and Plant Engineers serves as a source book for plant engineers, consultants, and boiler designers.

Download or read book Cleaner Combustion and Sustainable World written by Haiying Qi and published by Springer Science & Business Media. This book was released on 2012-11-19 with total page 1306 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cleaner Combustion and Sustainable World is the proceedings of the 7th International Symposium on Coal Combustion which has a significant international influence. It concerns basic research on coal combustion and clean utilization, techniques and equipments of pulverized coal combustion, techniques and equipments of fluidized bed combustion, basic research and techniques of emission control, basic research and application techniques of carbon capture and storage (CCS), etc. Professor Haiying Qi and Bo Zhao both work at the Tsinghua University, China

Download or read book Chemical Engineering Progress written by and published by . This book was released on 2009 with total page 452 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Energy Conversion Engineering written by Ahmed F. Ghoniem and published by Cambridge University Press. This book was released on 2021-11-11 with total page 842 pages. Available in PDF, EPUB and Kindle. Book excerpt: This unique textbook equips students with the theoretical and practical tools needed to model, design, and build efficient and clean low-carbon energy systems. Students are introduced to thermodynamics principles including chemical and electrochemical thermodynamics, moving onto applications in real-world energy systems, demonstrating the connection between fundamental concepts and theoretical analysis, modelling, application, and design. Topics gradually increase in complexity, nurturing student confidence as they build towards the use of advanced concepts and models for low to zero carbon energy conversion systems. The textbook covers conventional and emerging renewable energy conversion systems, including efficient fuel cells, carbon capture cycles, biomass utilisation, geothermal and solar thermal systems, hydrogen and low-carbon fuels. Featuring numerous worked examples, over 100 multi-component homework problems, and online instructor resources including lecture slides, solutions, and sample term projects, this textbook is the perfect teaching resource for an advanced undergraduate and graduate-level course in energy conversion engineering.

Download or read book Inventory of Federal Energy related Environment and Safety Research for written by and published by . This book was released on 1980 with total page 704 pages. Available in PDF, EPUB and Kindle. Book excerpt:

Download or read book Fundamentals and Applications of Supercritical Carbon Dioxide SCO2 Based Power Cycles written by Klaus Brun and published by Woodhead Publishing. This book was released on 2017-01-09 with total page 464 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fundamentals and Applications of Supercritical Carbon Dioxide (SCO2) Based Power Cycles aims to provide engineers and researchers with an authoritative overview of research and technology in this area. Part One introduces the technology and reviews the properties of SCO2 relevant to power cycles. Other sections of the book address components for SCO2 power cycles, such as turbomachinery expanders, compressors, recuperators, and design challenges, such as the need for high-temperature materials. Chapters on key applications, including waste heat, nuclear power, fossil energy, geothermal and concentrated solar power are also included. The final section addresses major international research programs. Readers will learn about the attractive features of SC02 power cycles, which include a lower capital cost potential than the traditional cycle, and the compounding performance benefits from a more efficient thermodynamic cycle on balance of plant requirements, fuel use, and emissions. Represents the first book to focus exclusively on SC02 power cycles Contains detailed coverage of cycle fundamentals, key components, and design challenges Addresses the wide range of applications of SC02 power cycles, from more efficient electricity generation, to ship propulsion

Download or read book Industrial Boilers and Heat Recovery Steam Generators written by V. Ganapathy and published by CRC Press. This book was released on 2002-10-16 with total page 650 pages. Available in PDF, EPUB and Kindle. Book excerpt: Filled with over 225 boiler/HRSG operation and design problems, this book covers steam generators and related systems used in process plants, refineries, chemical plants, electrical utilities, and other industrial settings. Emphasizing the thermal engineering aspects, the author provides information on the design and performance of steam generators