Download or read book Trade Catalogs on Hydraulic Brake Refrigerator and Aircraft Parts Tube and Pipe Fittings Hoses Hose Assemblies Drain and Shut off Cocks Automobile Parts Refrigeration Valves and Fittings Hydraulic Brake Fittings Gas Tank Caps Airplane Gasoline Oil Hydraulic and Air Valves Actuating Cylinders Universal Bulkhead and Safety Tube Fittings Fuel Line Assemblies and Silica Gel Strainers written by Weatherhead Company and published by . This book was released on 1934 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Automotive Air Brake Hose and Hose Assemblies written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2005 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This recommended practice covers minimum requirements for air brake hose assemblies made from reinforcedelastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame toaxle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed topotential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of-40 °C to +100 °C.This revision adds a fourth hose type, AIII, for use with permanent fittings only. Table 1 has been revised and nowcontains hoses A and AIII, Table 2 has been added for hoses AI and AII. All other Tables were renumbered accordingly.A note has been added that hose Type AIII in Table 1 can only be coupled with permanent fittings.
Download or read book Hydraulic and Air hydraulic Brakes Preventive Maaintenance written by and published by . This book was released on 1993 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book REFRIGERATION TUBE FITTINGSGENERAL SPECIFICATIONS written by Air Brake Tubing and Tube Ftg Committee and published by . This book was released on 1996 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers complete general and dimensional specifications for refrigeration tube fittings of the flare type specified in Figures 1 to 42 and Tables 1 to 15. These fittings are intended for general use with flared annealed copper tubing in refrigeration applications.Dimensions of single and double 45 degree flares on tubing to be used in conjunction with these fittings are given in Figure 2 and Table 1 of SAE J533.The following general specifications supplement the dimensional data contained in Tables 1 to 15 with respect to all unspecified details.
Download or read book Catalogue Of High Pressure Hydraulic Fittings And Other Flanges written by John [From Old Catalog] Platt and published by Legare Street Press. This book was released on 2022-10-27 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work has been selected by scholars as being culturally important, and is part of the knowledge base of civilization as we know it. This work is in the "public domain in the United States of America, and possibly other nations. Within the United States, you may freely copy and distribute this work, as no entity (individual or corporate) has a copyright on the body of the work. Scholars believe, and we concur, that this work is important enough to be preserved, reproduced, and made generally available to the public. We appreciate your support of the preservation process, and thank you for being an important part of keeping this knowledge alive and relevant.
Download or read book Trade Catalogs on Air and Hydraulic Equipment Controls and Hose and Fittings written by H.E. Linney Co and published by . This book was released on 1960 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Recommended Practices for Hydraulic Hose Assemblies written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2014 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems. J1273 has been reaffirmed to comply with the SAE five-year review policy.
Download or read book AIR BRAKE HOSE written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 1968 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This specification covers six types of air hose intended for use in automotive air brake systems. The system includes all air actuated equipment leading from the air brake line. These types of hose are not to be used from the air compressor to air reservoir if air temperature is in excess of 250 F. The types of hose are as follows: Type AHose shall be mandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings. Type BHose shall be nonmandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings. Type CHose shall be mandrel built having a tube of oil resisting rubber, reinforced with one braid of high tensile steel wire and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. A cotton braid or other suitable material may be used to anchor the cover to the hose. Assemble with permanent type metal end fittings only. Type DHose shall be mandrel built having a tube of oil resisting rubber, reinforced by two cotton or synthetic braids separated by a wire braid. All braids are to be impregnated with an oil and age resisting compound. The wire braid may be of high tensile carbon steel or of series 300 stainless steel. Hose may also have an optional thin cover of oil resisting compound utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings. Class IThe wire braid shall be of high tensile carbon steel. Class IIThe wire braid shall be of 300 series stainless steel. Type EHose shall be mandrel built having a tube of oil resisting lubber, reinforced with two cotton or synthetic braids separated by a wire braid. All braids are to be impregnated with an oil and age resisting compound. This hose is not to be used on any line where abrasion of the outer cover will be encountered in its service. Assemble with reusable type metal end fittings only. Type FHose shall be mandrel built having a tube of oil resisting rubber, reinforced with one 300 Series stainless steel braid and one fabric braid separated by an insulation layer of oil resisting rubber. The fabric braid is to be impregnated with an oil and age resistant compound. Assembled with reusable or permanent type metal end fittings.
Download or read book Tubing Motor Vehicle Brake System Hydraulic written by Hydraulic Brake Components Standards Committee and published by . This book was released on 1990 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a performance requirement qualification specification intended to give reasonable flexibility in the initial engineering selection of materials when fabricated by currently accepted manufacturing processes. It is not intended to be used for quality control purposes.This SAE Recommended Practice covers the tubing intended primarily for use as hydraulic brake lines on motor vehicles. It covers materials, manufacturing processes, and general properties required to meet the wide range of service encountered in automotive applications. To meet this need, it must be formed, assembled, handled, and installed in accordance with sound engineering and manufacturing practices. This specification covers only the basic tubing and does not include attachments such as protective armor or end fittings.
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections Four Bolt Split Flange Type written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2013 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers complete general and dimensional specifications for the flanged heads and split flange clamp halves applicable to four-bolt split flange type tube, pipe, and hose connections with appropriate references to the O-ring seals and attaching components used in their assembly. (See Figures 1 and 2.) Also included are recommended port dimensions and port design considerations.The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections.THE RATED WORKING PRESSURE OF A HOSE ASSEMBLY COMPRISING SAE J518 HOSE CONNECTIONS AND SAE J517 HOSE SHALL NOT EXCEED THE LOWER OF THE TWO WORKING PRESSURE RATED VALUES.Flanged heads shall be as specified in Figure 3 and Table 1. Split flange clamp halves shall be as specified in Figure 4 and Table 1. Port dimensions and spacing shall be as specified in Figure 5 and Table 2.O-ring seals, having nominal dimensions as indicated in Table 1, are used in conjunction with these connections. They shall conform to the seals specified in SAE J120, Table on Dimensions and Tolerances.Bolts for use with these connections shall be of the sizes and lengths indicated in Table 1. They shall be of SAE Grade 5 material or better as specified in SAE J429. Socket head cap screws of SAE Grade 5 material or better are acceptable.Lock washers, if used, shall be in accordance with the light spring lock washers specified in SAE J489, Dimensions of Light, Medium, Heavy, Extra Heavy, and Hi Collar Spring Lock Washers, and of sizes applicable to the corresponding bolts.The following general specifications supplement the dimensional data contained in Table 1 with respect to all unspecified detail. Superseded by SAE J518/1 and SAE J518/2.
Download or read book CATALOGUE OF HIGH PRESSURE HYD written by John Platt and published by Wentworth Press. This book was released on 2016-08-25 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work has been selected by scholars as being culturally important, and is part of the knowledge base of civilization as we know it. This work was reproduced from the original artifact, and remains as true to the original work as possible. Therefore, you will see the original copyright references, library stamps (as most of these works have been housed in our most important libraries around the world), and other notations in the work. This work is in the public domain in the United States of America, and possibly other nations. Within the United States, you may freely copy and distribute this work, as no entity (individual or corporate) has a copyright on the body of the work. As a reproduction of a historical artifact, this work may contain missing or blurred pages, poor pictures, errant marks, etc. Scholars believe, and we concur, that this work is important enough to be preserved, reproduced, and made generally available to the public. We appreciate your support of the preservation process, and thank you for being an important part of keeping this knowledge alive and relevant.
Download or read book Hydraulic Hose Fittings written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2019 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary equipment.The general specifications contained in Sections 1 through 17 are applicable to all hydraulic hose fittings and supplement the detailed specifications for the 100R-series fittings contained in the later sections of this document.This document shall be utilized as a procurement document only to the extent agreed upon by the manufacturer and user.Refer to SAE J517 for specifications of hose and information on hose assemblies. SAE J1273 contains information on application factors affecting hose fittings, hose, and hose assemblies.The rated working pressure of a hose assembly comprising SAE J516 fittings and SAE J517 hoses shall not exceed the lower of the two working pressure rated values.The following are hose fitting types contained in this document: Male and female 45-degree flare hose fittings shall be as shown by the 37-degree flare figures and tables.It is recommended that where step sizes or additional types of fittings are required, they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail. This revision of SAE J516 corrected some typographical errors, included additional verbiage for larger size hexes used on swivel nut fittings, and added Section 17.
Download or read book Hydraulic Flanged Tube Pipe and Hose Connections 4 Screw Flange Connection Part 2 42 MPa Code 62 written by Hydraulic Hose and Hose Fittings Committee and published by . This book was released on 2017 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard covers general and dimensional specifications for the Code 62 metric (type 1) and inch (type 2) flanged heads, flange clamps (FC and FCM), and split flange clamps (FCS and FCSM) applicable to four-screw flange type tube, pipe, and hose connections. Also included are the recommended port dimensions and port design considerations. Type 2 (inch) flange clamps and split flanges are not for new design.The flanged heads specified are incorporated into fittings having suitable means for attachment of tubes, pipes, or hoses to provide connection ends. These connections are intended for application in hydraulic systems, on industrial and commercial products, where it is desired to avoid the use of threaded connections.The rated working pressure of an assembly shall not exceed the least of all the component working pressure rated values.THE FOLLOWING GENERAL SPECIFICATIONS SUPPLEMENT THE DIMENSIONAL DATA CONTAINED IN THE TABLES WITH RESPECT TO ALL UNSPECIFIED DETAIL. PARTS MANUFACTURED TO THIS STANDARD ARE INTERCHANGEABLE WITH ISO 6162-2 AND CONNECTORS TO EITHER STANDARD CAN BE SUPPLIED WITH THE EXCEPTION OF THE -40 AND -48 TYPE 2 CONNECTIONS THAT ARE INCLUDED IN J518-2, BUT NOT ISO 6162-2. The DN 63 (-40) and DN 76 (-48) pad sizes existed for many years as special items in the field. Flange clamps were not available and the pads were used with pipe fittings. A couple of years ago, Italy proposed a clamp and supplied test data to support the design. The type 1 (metric screw) version has been approved at the ISO level. This SAE revision adds the -40 and -48 sizes and adds the inch screw sizes that have been used for years in the field. Finally, an identification groove was added to the flanged head. The groove had been approved many years ago, but never made it into the standard.
Download or read book Flex O Tube Aircraft Hose Assemblies for Hydraulic Oil Fuel Air and Instrument Lines written by Flex-O-Tube Company and published by . This book was released on 1942 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Operator Organizational Direct Support and General Support Maintenance Manual Including Repair Parts List for Repair Kit Hose Assembly Model Number SEHARK NSN 4940 01 080 4213 written by and published by . This book was released on 1992 with total page 176 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ROAD VEHICLEHYDRAULIC BRAKE HOSE ASSEMBLIES FOR USE WITH NON PETROLEUM BASE HYDRAULIC FLUIDS written by Automotive Brake and Steering Hose Standards Comm and published by . This book was released on 1978 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This SAE Standard specifies the test procedures and performance for hydraulic brake hose assemblies to be used in the hydraulic braking system of a road vehicle, and the markings to be put on the brake hose.
Download or read book HYDRAULIC TUBE FITTINGS written by Hydraulic Tube Fittings Committee and published by . This book was released on 1989 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This standard covers complete general and dimensional specifications for 37 degree flared and flareless types of hydraulic tube fittings and O-ring plugs. Also included are pipe fittings for use in conjunction with these tube fittings. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products.These fittings are capable of providing leak-proof, full-flow connections in hydraulic systems operating at working pressures as specified in SAE J1065, "Pressure Ratings for Hydraulic Tubing and Fittings."Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, the values shown in SAE J1065 should not be construed as a guaranteed minimum.For any severe applications, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure that performance levels will be safe and satisfactory.The standard is divided into five sections as follows:
