Download or read book Toward the Optimization of Low temperature Solution based Synthesis of ZnO Nanostructures for Device Applications written by Hatim Alnoor and published by Linköping University Electronic Press. This book was released on 2017-10-06 with total page 67 pages. Available in PDF, EPUB and Kindle. Book excerpt: One-dimensional (1D) nanostructures (NSs) of Zinc Oxide (ZnO) such as nanorods (NRs) have recently attracted considerable research attention due to their potential for the development of optoelectronic devices such as ultraviolet (UV) photodetectors and light-emitting diodes (LEDs). The potential of ZnO NRs in all these applications, however, would require synthesis of high crystal quality ZnO NRs with precise control over the optical and electronic properties. It is known that the optical and electronic properties of ZnO NRs are mostly influenced by the presence of native (intrinsic) and impurities (extrinsic) defects. Therefore, understanding the nature of these intrinsic and extrinsic defects and their spatial distribution is critical for optimizing the optical and electronic properties of ZnO NRs. However, identifying the origin of such defects is a complicated matter, especially for NSs, where the information on anisotropy is usually lost due to the lack of coherent orientation. Thus, the aim of this thesis is towards the optimization of the lowtemperature solution-based synthesis of ZnO NRs for device applications. In this connection, we first started with investigating the effect of the precursor solution stirring durations on the deep level defects concentration and their spatial distribution along the ZnO NRs. Then, by choosing the optimal stirring time, we studied the influence of ZnO seeding layer precursor’s types, and its molar ratios on the density of interface defects. The findings of these investigations were used to demonstrate ZnO NRs-based heterojunction LEDs. The ability to tune the point defects along the NRs enabled us further to incorporate cobalt (Co) ions into the ZnO NRs crystal lattice, where these ions could occupy the vacancies or interstitial defects through substitutional or interstitial doping. Following this, high crystal quality vertically welloriented ZnO NRs have been demonstrated by incorporating a small amount of Co into the ZnO crystal lattice. Finally, the influence of Co ions incorporation on the reduction of core-defects (CDs) in ZnO NRs was systematically examined using electron paramagnetic resonance (EPR).
Download or read book Toward the Optimization of Low temperature Solution based Synthesis of ZnO Nanostructures for Device Applications written by Hatim Alnoor and published by . This book was released on 2017 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: One-dimensional (1D) nanostructures (NSs) of Zinc Oxide (ZnO) such as nanorods (NRs) have recently attracted considerable research attention due to their potential for the development of optoelectronic devices such as ultraviolet (UV) photodetectors and light-emitting diodes (LEDs). The potential of ZnO NRs in all these applications, however, would require synthesis of high crystal quality ZnO NRs with precise control over the optical and electronic properties. It is known that the optical and electronic properties of ZnO NRs are mostly influenced by the presence of native (intrinsic) and impurities (extrinsic) defects. Therefore, understanding the nature of these intrinsic and extrinsic defects and their spatial distribution is critical for optimizing the optical and electronic properties of ZnO NRs. However, identifying the origin of such defects is a complicated matter, especially for NSs, where the information on anisotropy is usually lost due to the lack of coherent orientation. Thus, the aim of this thesis is towards the optimization of the lowtemperature solution-based synthesis of ZnO NRs for device applications. In this connection, we first started with investigating the effect of the precursor solution stirring durations on the deep level defects concentration and their spatial distribution along the ZnO NRs. Then, by choosing the optimal stirring time, we studied the influence of ZnO seeding layer precursor’s types, and its molar ratios on the density of interface defects. The findings of these investigations were used to demonstrate ZnO NRs-based heterojunction LEDs. The ability to tune the point defects along the NRs enabled us further to incorporate cobalt (Co) ions into the ZnO NRs crystal lattice, where these ions could occupy the vacancies or interstitial defects through substitutional or interstitial doping. Following this, high crystal quality vertically welloriented ZnO NRs have been demonstrated by incorporating a small amount of Co into the ZnO crystal lattice. Finally, the influence of Co ions incorporation on the reduction of core-defects (CDs) in ZnO NRs was systematically examined using electron paramagnetic resonance (EPR).
Download or read book Issues in Chemistry and General Chemical Research 2011 Edition written by and published by ScholarlyEditions. This book was released on 2012-01-09 with total page 10508 pages. Available in PDF, EPUB and Kindle. Book excerpt: Issues in Chemistry and General Chemical Research: 2011 Edition is a ScholarlyEditions™ eBook that delivers timely, authoritative, and comprehensive information about Chemistry and General Chemical Research. The editors have built Issues in Chemistry and General Chemical Research: 2011 Edition on the vast information databases of ScholarlyNews.™ You can expect the information about Chemistry and General Chemical Research in this eBook to be deeper than what you can access anywhere else, as well as consistently reliable, authoritative, informed, and relevant. The content of Issues in Chemistry and General Chemical Research: 2011 Edition has been produced by the world’s leading scientists, engineers, analysts, research institutions, and companies. All of the content is from peer-reviewed sources, and all of it is written, assembled, and edited by the editors at ScholarlyEditions™ and available exclusively from us. You now have a source you can cite with authority, confidence, and credibility. More information is available at http://www.ScholarlyEditions.com/.
Download or read book Solution Processed Metal Oxide Thin Films for Electronic Applications written by Zheng Cui and published by Elsevier. This book was released on 2020-06-11 with total page 180 pages. Available in PDF, EPUB and Kindle. Book excerpt: Solution Processed Metal Oxide Thin Films for Electronic Applications discusses the fundamentals of solution processing materials chemistry techniques as they are applied to metal oxide materials systems for key device applications. The book introduces basic information (materials properties, materials synthesis, barriers), discusses ink formulation and solution processing methods, including sol-gel processing, surface functionalization aspects, and presents a comprehensive accounting on the electronic applications of solution processed metal oxide films, including thin film transistors, photovoltaic cells and other electronics devices and circuits. This is an important reference for those interested in oxide electronics, printed electronics, flexible electronics and large-area electronics. Provides in-depth information on solution processing fundamentals, techniques, considerations and barriers combined with key device applications Reviews important device applications, including transistors, light-emitting diodes, and photovoltaic cells Includes an overview of metal oxide materials systems (semiconductors, nanomaterials and thin films), addressing materials synthesis, properties, limitations and surface aspects
Download or read book Carbon and Oxide Nanostructures written by Noorhana Yahya and published by Springer Science & Business Media. This book was released on 2011-01-12 with total page 413 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume covers all aspects of carbon and oxide based nanostructured materials. The topics include synthesis, characterization and application of carbon-based namely carbon nanotubes, carbon nanofibres, fullerenes, carbon filled composites etc. In addition, metal oxides namely, ZnO, TiO2, Fe2O3, ferrites, garnets etc., for various applications like sensors, solar cells, transformers, antennas, catalysts, batteries, lubricants, are presented. The book also includes the modeling of oxide and carbon based nanomaterials. The book covers the topics: Synthesis, characterization and application of carbon nanotubes, carbon nanofibres, fullerenes Synthesis, characterization and application of oxide based nanomaterials. Nanostructured magnetic and electric materials and their applications. Nanostructured materials for petro-chemical industry. Oxide and carbon based thin films for electronics and sustainable energy. Theory, calculations and modeling of nanostructured materials.
Download or read book ZnO Nanostructures written by Yue Zhang and published by Royal Society of Chemistry. This book was released on 2017-06-21 with total page 307 pages. Available in PDF, EPUB and Kindle. Book excerpt: As wide band semiconductors with rich morphologies and interesting electric, optical, mechanical and piezoelectric properties, ZnO nanostructures have great potential in applications, such as strain sensors, UV detectors, blue LED, nano generators, and biosensors. ZnO Nanostructures: Fabrication and Applications covers the controllable synthesis and property optimization of ZnO nanostructures through to the preparation and performance of nanodevices for various applications. The book also includes recent progress in property modulation of ZnO nanomaterials and new types of devices as well as the latest research on self-powered devices and performance modulation of ZnO nanodevices by multi-field coupled effects. Authored by a leading researcher working within the field, this volume is applicable for those working in nanostructure fabrication and device application in industry and academia and is appropriate from advanced undergraduate level upwards.
Download or read book Zinc Oxide Nanostructures written by Magnus Willander and published by CRC Press. This book was released on 2014-07-22 with total page 234 pages. Available in PDF, EPUB and Kindle. Book excerpt: Zinc oxide (ZnO) in its nanostructured form is emerging as a promising material with great potential for the development of many smart electronic devices. This book presents up-to-date information about various synthesis methods to obtain device-quality ZnO nanostructures. It describes both high-temperature (over 100° C) and low-temperature (under 100° C) approaches to synthesizing ZnO nanostructures; device applications for technical and medical devices, light-emitting diodes, electrochemical sensors, nanogenerators, and photodynamic therapy; and the concept of self-powered devices and systems using ZnO nanostructures. The book emphasizes the utilization of non-conventional substrates such as plastic, paper, and textile as new platforms for developing electronics.
Download or read book Zinc Oxide Based Nano Materials and Devices written by , Prof. Dr. Ahmed Nahhas and published by BoD – Books on Demand. This book was released on 2019-10-09 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents a review of recent advances in ZnO-based nanomaterials and devices. ZnO as a nanomaterial has gained substantial interest in the research area of wide bandgap semiconductors and is considered to be one of the major candidates for electronic and photonic applications. ZnO has distinguished and interesting electrical and optical properties and is considered to be a potential material in optoelectronic applications such as solar cells, surface acoustic wave devices, and UV emitters. ZnO's unique properties have attracted several researchers to study its electrical and optical properties. As a nanostructured material, ZnO exhibits many advantages for nanodevices. Moreover, it has the ability to absorb the UV radiation.
Download or read book Contemporary Trends in Semiconductor Devices written by Rupam Goswami and published by Springer Nature. This book was released on 2022-02-16 with total page 313 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book covers evolution, concept and applications of modern semiconductor devices such as tunnel field effect transistors (TFETs), vertical super-thin body MOSFETs, ion sensing FETs (ISFETs), non-conventional solar cells, opto-electro mechanical devices and thin film transistors (TFTs). Comprising of theory, experimentation and applications of devices, the chapters describe state-of-art methods and techniques which shall be highly assistive in having an overall perspective on emerging technologies and working on a research area. The book is aimed at the scholars, enthusiasts and researchers who are currently working on devices in the contemporary era of semiconductor devices. Additionally, the chapters are lucid and descriptive and carry the potential of serving as a reference book for scholars in their undergraduate studies, who are looking ahead for a prospective career in semiconductor devices.
Download or read book Chemical Solution Synthesis for Materials Design and Thin Film Device Applications written by Soumen Das and published by Elsevier. This book was released on 2021-01-09 with total page 748 pages. Available in PDF, EPUB and Kindle. Book excerpt: Chemical Solution Synthesis for Materials Design and Thin Film Device Applications presents current research on wet chemical techniques for thin-film based devices. Sections cover the quality of thin films, types of common films used in devices, various thermodynamic properties, thin film patterning, device configuration and applications. As a whole, these topics create a roadmap for developing new materials and incorporating the results in device fabrication. This book is suitable for graduate, undergraduate, doctoral students, and researchers looking for quick guidance on material synthesis and device fabrication through wet chemical routes. Provides the different wet chemical routes for materials synthesis, along with the most relevant thin film structured materials for device applications Discusses patterning and solution processing of inorganic thin films, along with solvent-based processing techniques Includes an overview of key processes and methods in thin film synthesis, processing and device fabrication, such as nucleation, lithography and solution processing
Download or read book Metal Oxide Based Photocatalysis written by Adriana Zaleska-Medynska and published by Elsevier. This book was released on 2018-04-09 with total page 372 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal Oxide-Based Photocatalysis: Fundamentals and Prospects for Application explains the principles and fundamentals of metal oxide-based photocatalysis and the requirements necessary for their use in photocatalysis. It also discusses preparation methods for photocatalysis, and the advantages, disadvantages and achievements of the most important metal oxides (TiO2, ZnO, Fe2O3, Ta2O3, CuO, NiO, Cr2O3, RuO2, etc.). The book concludes with the most important photocatalytic applications and an overview of the future. Applications are organized by potential needs and solutions, addressing such areas as water treatment, hydrogen production, air treatment, chemical synthesis, and applications in medicine and construction. Provides coverage of applications, presenting needs and solutions Covers essential applications, such as water treatment, hydrogen production, air depollution, medical applications, and much more Includes the characterization of the most important metal oxides used in heterogeneous photocatalysis
Download or read book Nanostructured Zinc Oxide written by Kamlendra Awasthi and published by Elsevier. This book was released on 2021-08-10 with total page 781 pages. Available in PDF, EPUB and Kindle. Book excerpt: Nanostructured Zinc Oxide covers the various routes for the synthesis of different types of nanostructured zinc oxide including; 1D (nanorods, nanowires etc.), 2D and 3D (nanosheets, nanoparticles, nanospheres etc.). This comprehensive overview provides readers with a clear understanding of the various parameters controlling morphologies. The book also reviews key properties of ZnO including optical, electronic, thermal, piezoelectric and surface properties and techniques in order to tailor key properties. There is a large emphasis in the book on ZnO nanostructures and their role in optoelectronics. ZnO is very interesting and widely investigated material for a number of applications. This book presents up-to-date information about the ZnO nanostructures-based applications such as gas sensing, pH sensing, photocatalysis, antibacterial activity, drug delivery, and electrodes for optoelectronics. Reviews methods to synthesize, tailor, and characterize 1D, 2D, and 3D zinc oxide nanostructured materials Discusses key properties of zinc oxide nanostructured materials including optical, electronic, thermal, piezoelectric, and surface properties Addresses most relevant zinc oxide applications in optoelectronics such as light-emitting diodes, solar cells, and sensors
Download or read book Metal Oxide Nanostructures written by Daniela Nunes and published by Elsevier. This book was released on 2018-11-01 with total page 328 pages. Available in PDF, EPUB and Kindle. Book excerpt: Metal Oxide Nanostructures: Synthesis, Properties and Applications covers the theoretical and experimental aspects related to design, synthesis, fabrication, processing, structural, morphological, optical and electronic properties on the topic. In addition, it reviews surface functionalization and hybrid materials, focusing on the advantages of these oxide nanostructures. The book concludes with the current and future prospective applications of these materials. Users will find a complete overview of all the important topics related to oxide nanostructures, from the physics of the materials, to its application. Delves into hybrid structured metal oxides and their promising use in the next generation of electronic devices Includes fundamental chapters on synthesis design and the properties of metal oxide nanostructures Provides an in-depth overview of novel applications, including chromogenics, electronics and energy
Download or read book Nanostructures written by Sadia Ameen and published by BoD – Books on Demand. This book was released on 2020-02-19 with total page 146 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights the functionality, significance, and applicability of nanostructure materials. The chapters in this book provide the logical and comprehensive information pertaining to the recent advances in the synthesis, characterization, and application of nanostructure materials for energy conversion and sensors. Written by an outstanding group of experts in the field, this book presents the latest advances and developments in nanostructure materials. We hope this book will help in describing the current position of nanostructure materials in the technological sphere as well as encourage scientists and engineers in deeper exploration of nanostructure materials to boost the technological advancement.
Download or read book Synthesis of ZnO CuO and Their Composite Nanostructures for Optoelectronics Sensing and Catalytic Applications written by Saima Zaman and published by . This book was released on 2012 with total page 59 pages. Available in PDF, EPUB and Kindle. Book excerpt: Research on nanomaterials has become increasingly popular because of their unique physical, chemical, optical and catalytic properties compared to their bulk counterparts. Therefore, many efforts have been made to synthesize multidimensional nanostructures for new and efficient nanodevices. Among those materials, zinc oxide (ZnO), has gained substantial attention owing to many outstanding properties. ZnO besides its wide bandgap of 3.34 eV exhibits a relatively large exciton binding energy (60 meV) at room temperature which is attractive for optoelectronic applications. Likewise, cupric oxide (CuO), having a narrow band gap of 1.2 eV and a variety of chemo-physical properties that are attractive in many fields. Moreover, composite nanostructures of these two oxides (CuO/ZnO) may pave the way for various new applications.??This thesis can be divided into three parts concerning the synthesis, characterization and applications of ZnO, CuO and their composite nanostructures.??In the first part the synthesis, characterization and the fabrication of ZnO nanorods based hybrid light emitting diodes (LEDs) are discussed. The low temperature chemical growth method was used to synthesize ZnO nanorods on different substrates, specifically on flexible non-crystalline substrates. Hybrid LEDs based on ZnO nanorods combined with p-type polymers were fabricated at low temperature to examine the advantage of both materials. A single and blended light emissive polymers layer was studied for controlling the quality of the emitted white light.??The second part deals with the synthesis of CuO nanostructures (NSs) which were then used to fabricate pH sensors and exploit these NSs as a catalyst for degradation of organic dyes. The fabricated pH sensor exhibited a linear response and good potential stability. Furthermore, the catalytic properties of petals and flowers like CuO NSs in the degradation of organic dyes were studied. The results showed that the catalytic reactivity of the CuO is strongly depending on its shape.??In the third part, an attempt to combine the advantages of both ZnO and CuO NSs was performed by developing a two-step chemical growth method to synthesize the composite NSs. The synthesized CuO/ZnO composite NSs revealed an extended light absorption and enhanced defect related visible emission.
Download or read book Chemically Deposited Nanocrystalline Metal Oxide Thin Films written by Fabian I. Ezema and published by Springer Nature. This book was released on 2021-06-26 with total page 926 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book guides beginners in the areas of thin film preparation, characterization, and device making, while providing insight into these areas for experts. As chemically deposited metal oxides are currently gaining attention in development of devices such as solar cells, supercapacitors, batteries, sensors, etc., the book illustrates how the chemical deposition route is emerging as a relatively inexpensive, simple, and convenient solution for large area deposition. The advancement in the nanostructured materials for the development of devices is fully discussed.
Download or read book 1 Dimensional Metal Oxide Nanostructures written by Zainovia Lockman and published by CRC Press. This book was released on 2018-12-07 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: 1-D metal oxide nanostructures, especially those with semiconducting properties, have attracted much attention in recent years due to their potential and emerging applications, specifically in environment purification and energy devices. For these applications, there have been many efforts to grow 1-D nanostructures in the form of nanotubes, nanorods, and nanowires using processes that conserve energy, are cost effective, and can be scaled up for large-scale production. 1-Dimensional Metal Oxide Nanostructures gathers under one title the most recent development of oxide nanomaterials, especially those fabricated via oxidation process in the nanoscale field. Thermal and anodic oxidation processes are reviewed with an aim to offer an in-depth understanding of mechanisms of 1-D nanostructure formation, their characteristics, and limitations. Other more common methods are also discussed, including sol-gel, hydrothermal, and other templated methods. Important applications of 1-D nanostructures are then presented, focusing on oxides like zinc oxide, titanium oxide, zirconium oxide, copper oxide, and iron oxide. A chapter on carbon nanotubes hybrid with these oxides is also included as well as one on silicon oxide nanowires formation by local anodic oxidation process. Aimed at researchers, academics, and engineers working across the fields of nanotechnology, materials science, chemistry, physics, semiconductors, and environmental and biomedical engineering, this essential reference enables readers to grasp the main concepts of nanomaterials in 1-D: formation technique, characteristics, and uses. It also encourages practical innovations in nanotechnology, especially in curbing pressing global issues related to energy, environment, and security.
