Download or read book Building Code Requirements for Structural Concrete ACI 318 05 and Commentary ACI 318R 05 written by ACI Committee 318 and published by American Concrete Institute. This book was released on 2005 with total page 432 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Joint ACICEB symposium concrete design US and European practices written by FIB – International Federation for Structural Concrete and published by FIB - International Federation for Structural Concrete. This book was released on 1976-08-01 with total page 354 pages. Available in PDF, EPUB and Kindle. Book excerpt: Proceedings of the symposium cosponsored by the American Concrete lnstitute, the Comité Euro International du Béton, the Prestressed Concrete lnstitute, and the Fédération Internationale de la Précontrainte.
Download or read book The Response of Reinforced Concrete to In plane Shear and Normal Stresses written by F. Vecchio and published by . This book was released on 1982 with total page 332 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Torsion of Structural Concrete written by and published by . This book was released on 1968 with total page 526 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Concrete Beams with Openings written by M. A. Mansur and published by CRC Press. This book was released on 1999-01-29 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book compiles state-of-the-art information on the behavior, analysis, and design of concrete beams containing transverse openings. Discussions include the need, effects, and classification of openings as well as the general requirements for fulfilling design pure bending, combined bending, and shear - illustrated with numerical examples torsion alone or in combination with bending and shear large rectangular openings as well as opening size and location on beam behavior methods for analyzing ultimate strength and serviceability requirements effects of torsion in beams large openings in continuous beams and their effects on possible redistribution of internal forces as well as guidelines and procedures for the design of such beams effect of prestressing on the serviceability and strength of beams with web openings design against cracking at openings and ultimate loads Concrete Beams with Openings serves as an invaluable source of information for designers and practicing engineers, especially useful since little or no provision or guidelines are currently available in most building codes.
Download or read book Torsion of Reinforced Concrete written by Thomas Tseng Chuang Hsu and published by Van Nostrand Reinhold Company. This book was released on 1984 with total page 554 pages. Available in PDF, EPUB and Kindle. Book excerpt: Good,No Highlights,No Markup,all pages are intact, Slight Shelfwear,may have the corners slightly dented, may have slight color changes/slightly damaged spine.
Download or read book Creative Systems in Structural and Construction Engineering written by Amarjit Singh and published by CRC Press. This book was released on 2017-11-22 with total page 1040 pages. Available in PDF, EPUB and Kindle. Book excerpt: An examination of creative systems in structural and construction engineering taken from conference proceedings. Topics covered range from construction methods, safety and quality to seismic response of structural elements and soils and pavement analysis.
Download or read book Proceedings of the Canadian Society of Civil Engineering Annual Conference 2021 written by Scott Walbridge and published by Springer Nature. This book was released on 2022-04-13 with total page 583 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises the proceedings of the Annual Conference of the Canadian Society of Civil Engineering 2021. The contents of this volume focus on specialty conferences in construction, environmental, hydrotechnical, materials, structures, transportation engineering, etc. This volume will prove a valuable resource for those in academia and industry.
Download or read book Design of Concrete Structures with Stress Fields written by Aurello Muttoni and published by Birkhäuser. This book was released on 2012-12-06 with total page 150 pages. Available in PDF, EPUB and Kindle. Book excerpt: 17 2 STRESS FIELDS FOR SIMPLE STRUCTURES 2. 1 INTRODUCTION In this chapter the behavior and strength of simple structures made of rein forced or prestressed concrete is investigated with the aid of stress fields. In particular, the webs and flanges of beams, simple walls, brackets, bracing beams and joints of frames are investigated. By this means, the majority of design cases are already covered. In reality, all structural components are three-dimensional. Here, however, components are considered either directly as two-dimensional plate elements (i. e. the plane stress condition with no variation of stress over the thickness of the element) or they are subdivided into several plates. Since two-dimensional structural elements are statically redundant, it is pOSSible for a particular loading to be in equilibrium with many (theoretically an infinite number of) stress states. If the lower bound method of the theory of plasticity is employed, then an admissible stress field or any combination of such stress fields may be selected. In chapter 4 it is shown that this method is suitable for the design of reinforced concrete structures, and the consequence of the choice of the final structural system on the structural behavior is dealt with in detail. The first cases of the use of this method date back to Ritter [6] and Morsch [4], who already at the beginning of the century investigated the resultants of the internal stresses by means of truss models.
Download or read book Behavior of UHPC Structural Members subjected to Pure Torsion written by Mohammed Ismail and published by kassel university press GmbH. This book was released on 2015-01-01 with total page 287 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ultra High Performance Concrete (UHPC) is characterized by a very high compressive strength which may reach more than 200 MPa. The behavior of this material under tension and compression actions has been established to be very brittle in nature. Discontinuous fibers (normally steel fibers) are usually added to the UHPC mix to introduce ductility. In order to investigate the beneficial effects of using fiber reinforced UHPC in structural members subjected to torsion, a series of experimental tests on 17 UHPC beams subjected to pure torsion were carried out. The test beams consisted of plain UHPC beams, UHPC beams reinforced with steel fibers only, UHPC reinforced with steel fibers and different combinations of traditional longitudinal and transverse reinforcement. The plain UHPC beams showed very brittle behavior, whereas the UHPC beams with steel fibers only showed a post cracking ductile behavior. The addition of little steel fiber volume (e.g. 0.5 %) to the plain UHPC beams enhanced the ductility. The enhancement at the ultimate capacity amounts to about 20 %. Meanwhile, the steel fibers with 0.9 % by volume showed much enhanced ductility and a maximum enhancement of the torsional carrying capacity up to 32 %. The addition of moderate steel fiber volume (e.g. 0.9 %) to one type of traditional reinforcement (either longitudinal or transverse) accomplished an effective post cracking torsional carrying mechanism. The steel fibers shows a tendency to replace the missing type of traditional reinforcement, however this should be confirmed by more tests and by using higher steel fiber volumes. A series of experimental tests on fiber reinforced UHPC prisms to investigate the post cracking shear strength and stiffness of the used UHPC mix (e.g. M3Q) was conducted. The results of these tests revealed that this fine grained UHPC mix has a weak post cracking shear behavior. The results of these tests were used later in the Finite Element (F.E) model. An analytical model based on the well known thin-walled tube analogy was developed in order to estimate the torsional carrying capacity of beams under pure torsion having different combinations of steel fibers and traditional reinforcement. The comparison between the test and model results showed very good agreement for all cases. A finite element model based on calibrated small scale tests was developed using ATENA F.E. package to predict the full load-deformation behavior of the test beams. The predictions of the model show very good agreement with the test results.
Download or read book Abhandlungen written by International Association for Bridge and Structural Engineering and published by . This book was released on 1968 with total page 196 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Practical Design of Reinforced Concrete Buildings written by Syed Mehdi Ashraf and published by CRC Press. This book was released on 2017-11-10 with total page 347 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book will provide comprehensive, practical knowledge for the design of reinforced concrete buildings. The approach will be unique as it will focus primarily on the design of various structures and structural elements as done in design offices with an emphasis on compliance with the relevant codes. It will give an overview of the integrated design of buildings and explain the design of various elements such as slabs, beams, columns, walls, and footings. It will be written in easy-to-use format and refer to all the latest relevant American codes of practice (IBC and ASCE) at every stage. The book will compel users to think critically to enhance their intuitive design capabilities.
Download or read book Fracture Mechanics of Concrete written by Surendra P. Shah and published by John Wiley & Sons. This book was released on 1995-09-28 with total page 588 pages. Available in PDF, EPUB and Kindle. Book excerpt: FRACTURE MECHANICS OF CONCRETE AND ROCK This book offers engineers a unique opportunity to learn, frominternationally recognized leaders in their field, about the latesttheoretical advances in fracture mechanics in concrete, reinforcedconcrete structures, and rock. At the same time, it functions as asuperb, graduate-level introduction to fracture mechanics conceptsand analytical techniques. Reviews, in depth, the basic theory behind fracture mechanics * Covers the application of fracture mechanics to compressionfailure, creep, fatigue, torsion, and other advanced topics * Extremely well researched, applies experimental evidence ofdamage to a wide range of design cases * Supplies all relevant formulas for stress intensity * Covers state-of-the-art linear elastic fracture mechanics (LEFM)techniques for analyzing deformations and cracking * Describes nonlinear fracture mechanics (NLFM) and the latestRILEM modeling techniques for testing nonlinear quasi-brittlematerials * And much more Over the past few years, researchers employing techniques borrowedfrom fracture mechanics have made many groundbreaking discoveriesconcerning the causes and effects of cracking, damage, andfractures of plain and reinforced concrete structures and rock.This, in turn, has resulted in the further development andrefinement of fracture mechanics concepts and tools. Yet, despitethe field's growth and the growing conviction that fracturemechanics is indispensable to an understanding of material andstructural failure, there continues to be a surprising shortage oftextbooks and professional references on the subject. Written by two of the foremost names in the field, FractureMechanics of Concrete fills that gap. The most comprehensive bookever written on the subject, it consolidates the latest theoreticalresearch from around the world in a single reference that can beused by students and professionals alike. Fracture Mechanics of Concrete is divided into two sections. In thefirst, the authors lay the necessary groundwork with an in-depthreview of fundamental principles. In the second section, theauthors vividly demonstrate how fracture mechanics has beensuccessfully applied to failures occurring in a wide array ofdesign cases. Key topics covered in these sections include: * State-of-the-art linear elastic fracture mechanics (LEFM)techniques for analyzing deformations and cracking * Nonlinear fracture mechanics (NLFM) and the latest RILEM modelingtechniques for testing nonlinear quasi-brittle materials * The use of R-Curves to describe cracking and fracture inquasi-brittle materials * The application of fracture mechanics to compression failure,creep, fatigue, torsion, and other advanced topics The most timely, comprehensive, and authoritative book on thesubject currently available, Fracture Mechanics of Concrete is botha complete instructional tool for academics and students instructural and geotechnical engineering courses, and anindispensable working resource for practicing engineers.
Download or read book Research Bulletin written by Malaviya Regional Engineering College and published by . This book was released on 1968 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1972 with total page 520 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Journal of the American Concrete Institute written by American Concrete Institute and published by . This book was released on 1985 with total page 1002 pages. Available in PDF, EPUB and Kindle. Book excerpt: Each number includes "Synopsis of recent articles."
Download or read book Magazine of Concrete Research written by and published by . This book was released on 1981 with total page 520 pages. Available in PDF, EPUB and Kindle. Book excerpt:
