Download or read book Friction Wear and Adhesion Characteristics of Titanium aluminum Alloys in Vacuum written by Donald H. Buckley and published by . This book was released on 1966 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: Friction, wear, and adhesion measurements were made in vacuum of titanium-aluminum alloys containing 11, 16, and 21 weight percent aluminum. Experiments were conducted with a 3/16 inch radius rider sliding on the flat surface of a 2.5 inch diameter disk specimen at loads to 1500 grams. The disk was rotated to produce sliding velocities to 750 centimeters per second. With increasing addition of aluminum to titanium, an increase in lattice ratio for titanium occurred along with a decrease in friction, wear, and adhesion. The increases in lattice ratio with the addition of aluminum to titanium occurred even though the unit cell size decreased; these results are unlike those with the addition of tin and oxygen to alloys exhibited adhesion characteristics which could be considered negligible. These alloys exhibited superior friction and wear properties in vacuum compared with 52100 and 440-C stainless steels. Experiments were conducted with the alloys sliding on themselves and on 440-C stainless steel. Friction was less for the alloys sliding on 440-C stainless than when sliding on themselves.
Download or read book Titanium Alloys written by Maciej Motyka and published by BoD – Books on Demand. This book was released on 2019-11-27 with total page 156 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium alloys, due to unique physical and chemical properties (mainly high relative strength combined with very good corrosion resistance), are considered as an important structural metallic material used in hi-tech industries (e.g. aerospace, space technology). This book provides information on new manufacturing and processing methods of single- and two-phase titanium alloys. The eight chapters of this book are distributed over four sections. The first section (Introduction) indicates the main factors determining application areas of titanium and its alloys. The second section (Manufacturing, two chapters) concerns modern production methods for titanium and its alloys. The third section (Thermomechanical and surface treatment, three chapters) covers problems of thermomechanical processing and surface treatment used for single- and two-phase titanium alloys. The fourth section (Machining, two chapters) describes the recent results of high speed machining of Ti-6Al-4V alloy and the possibility of application of sustainable machining for titanium alloys.
Download or read book Gamma Titanium Aluminide Alloys written by Fritz Appel and published by John Wiley & Sons. This book was released on 2011-10-17 with total page 763 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first book entirely dedicated to the topic emphasizes the relation between basic research and actual processing technologies. As such, it covers complex microstructures down to the nanometer scale, structure/property relationships and potential applications in key industries. From the contents: * Constitution * Thermophysical Constants * Phase Transformations and Microstructures * Deformation Behaviour * Strengthening Mechanisms * Creep * Fracture Behaviour * Fatigue * Oxidation Resistance and Related Issues * Alloy Design * Ingot Production and Component Casting * Powder Metallurgy * Wrought Processing * Joining * Surface Hardening * Applications and Component Assessment
Download or read book The Oxidation and Contamination of Titanium and Its Alloys written by J. M. Ferguson and published by . This book was released on 1968 with total page 22 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experimental programs concerned with the oxidation of titanium and its alloys are reviewed and results compared with those predicted by theory. Wagner-Hauffe theory is used as the primary basis for comparison, and its inconsistencies are pointed out. Fifteen binary alloy systems involving titanium are covered, as well as a few ternary and commercial alloys. A short section discusses the effects of oxygen or nitrogen contamination on the mechanical properties of titanium and its alloys. (Author).
Download or read book Titanium written by Matthew J. Donachie and published by ASM International. This book was released on 2000 with total page 381 pages. Available in PDF, EPUB and Kindle. Book excerpt: Designed to support the need of engineering, management, and other professionals for information on titanium by providing an overview of the major topics, this book provides a concise summary of the most useful information required to understand titanium and its alloys. The author provides a review of the significant features of the metallurgy and application of titanium and its alloys. All technical aspects of the use of titanium are covered, with sufficient metals property data for most users. Because of its unique density, corrosion resistance, and relative strength advantages over competing materials such as aluminum, steels, and superalloys, titanium has found a niche in many industries. Much of this use has occurred through military research, and subsequent applications in aircraft, of gas turbine engines, although more recent use features replacement joints, golf clubs, and bicycles.Contents include: A primer on titanium and its alloys, Introduction to selection of titanium alloys, Understanding titanium's metallurgy and mill products, Forging and forming, Castings, Powder metallurgy, Heat treating, Joining technology and practice, Machining, Cleaning and finishing, Structure/processing/property relationships, Corrosion resistance, Advanced alloys and future directions, Appendices: Summary table of titanium alloys, Titanium alloy datasheets, Cross-reference to titanium alloys, Listing of selected specification and standardization organizations, Selected manufacturers, suppliers, services, Corrosion data, Machining data.
Download or read book Consumable electrode Arc Melting of Titanium and Its Alloys written by R. W. Huber and published by . This book was released on 1957 with total page 46 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book PRICM 8 written by Fernand D. S. Marquis and published by John Wiley & Sons. This book was released on 2013-09-05 with total page 3600 pages. Available in PDF, EPUB and Kindle. Book excerpt: PRICM-8 features the most prominent and largest-scale interactions in advanced materials and processing in the Pacific Rim region. The conference is unique in its intrinsic nature and architecture which crosses many traditional discipline and cultural boundaries. The CD is a comprehensive collection of papers from the 15 symposia presented at this event.
Download or read book Titanium and Titanium Alloys written by Christoph Leyens and published by John Wiley & Sons. This book was released on 2006-03-06 with total page 532 pages. Available in PDF, EPUB and Kindle. Book excerpt: This handbook is an excellent reference for materials scientists and engineers needing to gain more knowledge about these engineering materials. Following introductory chapters on the fundamental materials properties of titanium, readers will find comprehensive descriptions of the development, processing and properties of modern titanium alloys. There then follows detailed discussion of the applications of titanium and its alloys in aerospace, medicine, energy and automotive technology.
Download or read book Lightweight Alloys for Aerospace Applications written by Kumar Jata and published by John Wiley & Sons. This book was released on 2013-10-07 with total page 421 pages. Available in PDF, EPUB and Kindle. Book excerpt: This proceedings volume from the 2001 TMS Annual Meeting & Exhibition covers advances made in the area of scientific understanding of technological application of lightweight alloys. Papers focus on fundamental science as well as application and concentrate on scientific advances in aluminum, magnesium, titanium, and beryllium alloys and their composites. Processing, structure-property relationship, failure mechanisms, and advanced joining themes are also discussed.
Download or read book Titanium Powder Metallurgy written by Ma Qian and published by Butterworth-Heinemann. This book was released on 2015-02-10 with total page 649 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium Powder Metallurgy contains the most comprehensive and authoritative information for, and understanding of, all key issues of titanium powder metallurgy (Ti PM). It summarizes the past, reviews the present and discusses the future of the science and technology of Ti PM while providing the world titanium community with a unique and comprehensive book covering all important aspects of titanium powder metallurgy, including powder production, powder processing, green shape formation, consolidation, property evaluation, current industrial applications and future developments. It documents the fundamental understanding and technological developments achieved since 1937 and demonstrates why powder metallurgy now offers a cost-effective approach to the near net or net shape fabrication of titanium, titanium alloys and titanium metal matrix composites for a wide variety of industrial applications. Provides a comprehensive and in-depth treatment of the science, technology and industrial practice of titanium powder metallurgy Each chapter is delivered by the most knowledgeable expert on the topic, half from industry and half from academia, including several pioneers in the field, representing our current knowledge base of Ti PM. Includes a critical review of the current key fundamental and technical issues of Ti PM. Fills a critical knowledge gap in powder metal science and engineering and in the manufacture of titanium metal and alloys
Download or read book Machining of Light Alloys written by Diego Carou and published by CRC Press. This book was released on 2018-08-06 with total page 230 pages. Available in PDF, EPUB and Kindle. Book excerpt: Aluminium, magnesium and titanium are alloys of special interest for engineering applications in a wide range of sectors such as aeronautics, automotive and medical. Their low density, along with sufficient mechanical properties, makes them especially adequate for sectors such as transportation allowing diminishing weight less fuel consumption and emissions to the atmosphere. Nowadays, machining is still one the most important manufacturing processes, not only for metal parts, but also for specially designed hybrid parts for more demanding new applications. A wide range of valuable research has been done on the machining of conventional engineering materials. However, when dealing with light alloys and hybrid materials containing them, they need to face new challenges. Particularly, it is important to analyse the suitability of the machining of these alloys in the current context of Industry 4.0, focusing on the development of cost-effective and sustainable processes. This book is a comprehensive source on the machining of light alloys, presenting a collection of both experimental and review studies. The work is arranged in eight chapters, presented by a group of international scholars, which analyse the main problems related to the machining of these alloys from different perspectives. Key Features A comprehensive state-of-the-art reference source on machining of light alloys Provides research on conventional and non-conventional machining process Offers current research topics on sustainable machining Presents research on the machining of hybrid materials using light alloys Includes applications for Industry 4.0 environments Machining of Light Alloys: Aluminum, Titanium, and Magnesium The aim of the book is to serve as a tool for helping researchers and practitioners to face machining challenges and facilitating the development of new industrial applications for light alloys.
Download or read book Stress corrosion Cracking in High Strength Steels and in Titanium and Aluminum Alloys written by Benjamin Floyd Brown and published by . This book was released on 1972 with total page 390 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book A High Temperature X ray Diffraction Study of Titanium aluminum Alloys written by Albert John Goldak and published by . This book was released on 1960 with total page 64 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Titanium and Titanium Alloys written by John Laurence Everhart and published by . This book was released on 1954 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Titanium Alloys written by Jan Sieniawski and published by BoD – Books on Demand. This book was released on 2013-05-15 with total page 160 pages. Available in PDF, EPUB and Kindle. Book excerpt: The book contains six chapters and covers topics dealing with biomedical applications of titanium alloys, surface treatment, relationships between microstructure and mechanical and technological properties, and the effect of radiation on the structure of the titanium alloys.
Download or read book Thermal Coatings for Titanium Aluminum Alloys written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-23 with total page 136 pages. Available in PDF, EPUB and Kindle. Book excerpt: Titanium aluminides and titanium alloys are candidate materials for use in hot structure and heat-shield components of hypersonic vehicles because of their good strength-to-weight characteristics at elevated temperature. However, in order to utilize their maximum temperature capability, they must be coated to resist oxidation and to have a high total remittance. Also, surface catalysis for recombination of dissociated species in the aerodynamic boundary layer must be minimized. Very thin chemical vapor deposition (CVD) coatings are attractive candidates for this application because of durability and very light weight. To demonstrate this concept, coatings of boron-silicon and aluminum-boron-silicon compositions were applied to the titanium-aluminides alpha2 (Ti-14Al-21Nb), super-alpha2 (Ti-14Al-23-Nb-2V), and gamma (Ti-33Al-6Nb-1Ta) and to the titanium alloy beta-21S (Ti-15Mo-3Al-3Nb-0.2Si). Coated specimens of each alloy were subjected to a set of simulated hypersonic vehicle environmental tests to determine their properties of oxidation resistance, surface catalysis, radiative emittance, and thermal shock resistance. Surface catalysis results should be viewed as relative performance only of the several coating-alloy combinations tested under the specific environmental conditions of the LaRC Hypersonic Materials Environmental Test System (HYMETS) arc-plasma-heated hypersonic wind tunnel. Tests were also conducted to evaluate the hydrogen transport properties of the coatings and any effects of the coating processing itself on fatigue life of the base alloys. Results are presented for three types of coatings, which are as follows: (1) a single layer boron silicon coating, (2) a single layer aluminum-boron-silicon coating, and (3) a multilayer coating consisting of an aluminum-boron-silicon sublayer with a boron-silicon outer layer. Cunnington, George R. and Clark, Ronald K. and Robinson, John C. Langley Research Center ALUMINIDES; ENVIRONMENTAL TESTS; HYPERSONIC VEHI...
Download or read book Materials Data for Cyclic Loading written by Chr Boller and published by . This book was released on 1987 with total page 388 pages. Available in PDF, EPUB and Kindle. Book excerpt: Based on the author's lecture notes for a course on Physical Chemistry of Oxides at High Temperatures held at the Graduate School of the Tokyo Institute of Technology, this book examines the micromechanism of migration of ions and electronic defects contained in solid and liquid oxides at high temperature. The book is primarily designed for use as a graduate-level text and includes 150 problems for students. The emphasis is on introduction of simple theories for transport properties of oxides, which can be universally used at low and high temperatures, for various combinations of oxides.
